From: Abel Vesa <abel.vesa@linaro.org>
To: Vinod Koul <vkoul@kernel.org>
Cc: mani@kernel.org, Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Kishon Vijay Abraham I <kishon@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
devicetree@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v2 6/6] phy: qcom-qmp-ufs: Add SM8550 support
Date: Mon, 16 Jan 2023 16:14:54 +0200 [thread overview]
Message-ID: <Y8Vb3jBR2AtAJlWQ@linaro.org> (raw)
In-Reply-To: <Y8GkZKwvOc5nPSjI@matsya>
On 23-01-14 00:05:16, Vinod Koul wrote:
> On 12-01-23, 15:05, Abel Vesa wrote:
> > Add SM8550 specific register layout and table configs.
>
> Not related, but was this tested with the UFS Gear 4 support from Mani?
> It would be great to have that added (here or separately)
I mentioned both Mani's and Dmitry's patchsets in the cover letter.
This patchset is based on both those patchsets.
>
> >
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> > drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 100 ++++++++++++++++++++++++
> > 1 file changed, 100 insertions(+)
> >
> > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> > index 5936a3a05002..a9b666f32f59 100644
> > --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> > @@ -95,6 +95,13 @@ static const unsigned int sm8150_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
> > [QPHY_PCS_POWER_DOWN_CONTROL] = QPHY_V4_PCS_UFS_POWER_DOWN_CONTROL,
> > };
> >
> > +static const unsigned int sm8550_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
> > + [QPHY_START_CTRL] = QPHY_V6_PCS_UFS_PHY_START,
> > + [QPHY_PCS_READY_STATUS] = QPHY_V6_PCS_UFS_READY_STATUS,
> > + [QPHY_SW_RESET] = QPHY_V6_PCS_UFS_SW_RESET,
> > + [QPHY_PCS_POWER_DOWN_CONTROL] = QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,
> > +};
> > +
> > static const struct qmp_phy_init_tbl msm8996_ufsphy_serdes[] = {
> > QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x0e),
> > QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0xd7),
> > @@ -599,6 +606,61 @@ static const struct qmp_phy_init_tbl sm8350_ufsphy_g4_pcs[] = {
> > QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_BIST_FIXED_PAT_CTRL, 0x0a),
> > };
> >
> > +static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_INITVAL2, 0x00),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x4c),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x99),
> > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x07),
> > +};
> > +
> > +static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
> > + QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x05),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
> > +};
> > +
> > +static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4, 0x0f),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
> > +
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1, 0xc2),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3, 0x1a),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B6, 0x60),
> > +
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE2_B3, 0x9e),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE2_B6, 0x60),
> > +
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B3, 0x9e),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B4, 0x0e),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B5, 0x36),
> > + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B8, 0x02),
> > +};
> > +
> > +static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
> > + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_SIGDET_CTRL2, 0x69),
> > + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
> > + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
> > + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
> > + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
> > +};
> > +
> > struct qmp_ufs_offsets {
> > u16 serdes;
> > u16 pcs;
> > @@ -703,6 +765,10 @@ static const char * const sm8450_ufs_phy_clk_l[] = {
> > "qref", "ref", "ref_aux",
> > };
> >
> > +static const char * const sm8550_ufs_phy_clk_l[] = {
> > + "qref", "ref",
> > +};
> > +
> > static const char * const sdm845_ufs_phy_clk_l[] = {
> > "ref", "ref_aux",
> > };
> > @@ -721,6 +787,15 @@ static const struct qmp_ufs_offsets qmp_ufs_offsets_v5 = {
> > .rx2 = 0xa00,
> > };
> >
> > +static const struct qmp_ufs_offsets qmp_ufs_offsets_v6 = {
> > + .serdes = 0,
> > + .pcs = 0x400,
> > + .tx = 0x1000,
> > + .rx = 0x1200,
> > + .tx2 = 0x1800,
> > + .rx2 = 0x1a00,
> > +};
> > +
> > static const struct qmp_phy_cfg msm8996_ufsphy_cfg = {
> > .lanes = 1,
> >
> > @@ -958,6 +1033,28 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
> > .regs = sm8150_ufsphy_regs_layout,
> > };
> >
> > +static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
> > + .lanes = 2,
> > +
> > + .offsets = &qmp_ufs_offsets_v6,
> > +
> > + .tbls = {
> > + .serdes = sm8550_ufsphy_serdes,
> > + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_serdes),
> > + .tx = sm8550_ufsphy_tx,
> > + .tx_num = ARRAY_SIZE(sm8550_ufsphy_tx),
> > + .rx = sm8550_ufsphy_rx,
> > + .rx_num = ARRAY_SIZE(sm8550_ufsphy_rx),
> > + .pcs = sm8550_ufsphy_pcs,
> > + .pcs_num = ARRAY_SIZE(sm8550_ufsphy_pcs),
> > + },
> > + .clk_list = sm8550_ufs_phy_clk_l,
> > + .num_clks = ARRAY_SIZE(sm8550_ufs_phy_clk_l),
> > + .vreg_list = qmp_phy_vreg_l,
> > + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
> > + .regs = sm8550_ufsphy_regs_layout,
> > +};
> > +
> > static void qmp_ufs_configure_lane(void __iomem *base,
> > const struct qmp_phy_init_tbl tbl[],
> > int num,
> > @@ -1467,6 +1564,9 @@ static const struct of_device_id qmp_ufs_of_match_table[] = {
> > }, {
> > .compatible = "qcom,sm8450-qmp-ufs-phy",
> > .data = &sm8450_ufsphy_cfg,
> > + }, {
> > + .compatible = "qcom,sm8550-qmp-ufs-phy",
> > + .data = &sm8550_ufsphy_cfg,
> > },
> > { },
> > };
> > --
> > 2.34.1
>
> --
> ~Vinod
prev parent reply other threads:[~2023-01-16 14:34 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-12 13:05 [PATCH v2 0/6] phy: qualcomm: Add UFS support for SM8550 Abel Vesa
2023-01-12 13:05 ` [PATCH v2 1/6] dt-bindings: phy: Add QMP UFS PHY comptible " Abel Vesa
2023-01-12 14:32 ` Krzysztof Kozlowski
2023-01-12 13:05 ` [PATCH v2 2/6] phy: qcom-qmp: qserdes-com: Add v6 register offsets Abel Vesa
2023-01-12 13:05 ` [PATCH v2 3/6] phy: qcom-qmp: qserdes-txrx: " Abel Vesa
2023-01-12 13:05 ` [PATCH v2 4/6] phy: qcom-qmp: qserdes-txrx-ufs: " Abel Vesa
2023-01-12 13:05 ` [PATCH v2 5/6] phy: qcom-qmp: pcs-ufs: " Abel Vesa
2023-01-12 13:05 ` [PATCH v2 6/6] phy: qcom-qmp-ufs: Add SM8550 support Abel Vesa
2023-01-12 15:29 ` Johan Hovold
2023-01-13 18:35 ` Vinod Koul
2023-01-16 14:14 ` Abel Vesa [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y8Vb3jBR2AtAJlWQ@linaro.org \
--to=abel.vesa@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kishon@kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=mani@kernel.org \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).