From: "Guido Günther" <guido.gunther@puri.sm>
To: Chris Morgan <macroalpha82@gmail.com>
Cc: dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
krzysztof.kozlowski+dt@linaro.org, robh+dt@kernel.org,
daniel@ffwll.ch, airlied@gmail.com, sam@ravnborg.org,
thierry.reding@gmail.com, megous@megous.com, kernel@puri.sm,
Chris Morgan <macromorgan@hotmail.com>
Subject: Re: [PATCH 2/2] drm/panel: st7703: Add support for Anbernic RG353V-V2 panel
Date: Fri, 20 Jan 2023 10:06:48 +0100 [thread overview]
Message-ID: <Y8pZqPH0rDSfxhVr@qwark.sigxcpu.org> (raw)
In-Reply-To: <20230119230415.1283379-3-macroalpha82@gmail.com>
Hi,
On Thu, Jan 19, 2023 at 05:04:15PM -0600, Chris Morgan wrote:
> From: Chris Morgan <macromorgan@hotmail.com>
>
> The Anbernic RG353V-V2 is a 5 inch panel used in a new revision of the
> Anbernic RG353V handheld gaming device. Add support for it.
>
> Unfortunately it appears this controller is not able to support 120hz
> or 100hz mode like the first revision panel.
>
> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> ---
> drivers/gpu/drm/panel/panel-sitronix-st7703.c | 102 +++++++++++++++++-
> 1 file changed, 99 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> index 86a472b01360..2ed0cdfa86de 100644
> --- a/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> +++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> @@ -28,6 +28,7 @@
> /* Manufacturer specific Commands send via DSI */
> #define ST7703_CMD_ALL_PIXEL_OFF 0x22
> #define ST7703_CMD_ALL_PIXEL_ON 0x23
> +#define ST7703_CMD_SETAPID 0xB1
> #define ST7703_CMD_SETDISP 0xB2
> #define ST7703_CMD_SETRGBIF 0xB3
> #define ST7703_CMD_SETCYC 0xB4
> @@ -41,12 +42,15 @@
> #define ST7703_CMD_UNKNOWN_BF 0xBF
> #define ST7703_CMD_SETSCR 0xC0
> #define ST7703_CMD_SETPOWER 0xC1
> +#define ST7703_CMD_SETECO 0xC6
> +#define ST7703_CMD_SETIO 0xC7
> +#define ST7703_CMD_SETCABC 0xC8
> #define ST7703_CMD_SETPANEL 0xCC
> -#define ST7703_CMD_UNKNOWN_C6 0xC6
> #define ST7703_CMD_SETGAMMA 0xE0
> #define ST7703_CMD_SETEQ 0xE3
> #define ST7703_CMD_SETGIP1 0xE9
> #define ST7703_CMD_SETGIP2 0xEA
> +#define ST7703_CMD_UNKNOWN_EF 0xEF
>
> struct st7703 {
> struct device *dev;
> @@ -266,8 +270,7 @@ static int xbd599_init_sequence(struct st7703 *ctx)
> * ESD_DET_TIME_SEL = 0 frames
> */);
>
> - /* Undocumented command. */
> - dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_C6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
> + dsi_dcs_write_seq(dsi, ST7703_CMD_SETECO, 0x01, 0x00, 0xFF, 0xFF, 0x00);
Thanks for catching this! Would make sense to split that into a separate
commit. With that fixed
Reviewed-by: Guido Günther <agx@sigxcpu.org>
-- Guido
>
> dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
> 0x74, /* VBTHS, VBTLS: VGH = 17V, VBL = -11V */
> @@ -355,6 +358,98 @@ static const struct st7703_panel_desc xbd599_desc = {
> .init_sequence = xbd599_init_sequence,
> };
>
> +static int rg353v2_init_sequence(struct st7703 *ctx)
> +{
> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> +
> + /*
> + * Init sequence was supplied by the panel vendor.
> + */
> +
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC, 0xf1, 0x12, 0x83);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETAPID, 0x00, 0x00, 0x00,
> + 0xda, 0x80);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP, 0x00, 0x13, 0x70);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF, 0x10, 0x10, 0x28,
> + 0x28, 0x03, 0xff, 0x00, 0x00, 0x00, 0x00);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP, 0x0a, 0x0a);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, 0x92, 0x92);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT, 0x25, 0x22,
> + 0xf0, 0x63);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI, 0x33, 0x81, 0x05,
> + 0xf9, 0x0e, 0x0e, 0x20, 0x00, 0x00, 0x00, 0x00,
> + 0x00, 0x00, 0x00, 0x44, 0x25, 0x00, 0x90, 0x0a,
> + 0x00, 0x00, 0x01, 0x4f, 0x01, 0x00, 0x00, 0x37);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x47);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_BF, 0x02, 0x11, 0x00);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR, 0x73, 0x73, 0x50, 0x50,
> + 0x00, 0x00, 0x12, 0x50, 0x00);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER, 0x53, 0xc0, 0x32,
> + 0x32, 0x77, 0xe1, 0xdd, 0xdd, 0x77, 0x77, 0x33,
> + 0x33);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETECO, 0x82, 0x00, 0xbf, 0xff,
> + 0x00, 0xff);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETIO, 0xb8, 0x00, 0x0a, 0x00,
> + 0x00, 0x00);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETCABC, 0x10, 0x40, 0x1e,
> + 0x02);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0b);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA, 0x00, 0x07, 0x0d,
> + 0x37, 0x35, 0x3f, 0x41, 0x44, 0x06, 0x0c, 0x0d,
> + 0x0f, 0x11, 0x10, 0x12, 0x14, 0x1a, 0x00, 0x07,
> + 0x0d, 0x37, 0x35, 0x3f, 0x41, 0x44, 0x06, 0x0c,
> + 0x0d, 0x0f, 0x11, 0x10, 0x12, 0x14, 0x1a);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ, 0x07, 0x07, 0x0b, 0x0b,
> + 0x0b, 0x0b, 0x00, 0x00, 0x00, 0x00, 0xff, 0x00,
> + 0xc0, 0x10);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1, 0xc8, 0x10, 0x02, 0x00,
> + 0x00, 0xb0, 0xb1, 0x11, 0x31, 0x23, 0x28, 0x80,
> + 0xb0, 0xb1, 0x27, 0x08, 0x00, 0x04, 0x02, 0x00,
> + 0x00, 0x00, 0x00, 0x04, 0x02, 0x00, 0x00, 0x00,
> + 0x88, 0x88, 0xba, 0x60, 0x24, 0x08, 0x88, 0x88,
> + 0x88, 0x88, 0x88, 0x88, 0x88, 0xba, 0x71, 0x35,
> + 0x18, 0x88, 0x88, 0x88, 0x88, 0x88, 0x00, 0x00,
> + 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> + 0x00, 0x00, 0x00);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2, 0x97, 0x0a, 0x82, 0x02,
> + 0x03, 0x07, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> + 0x81, 0x88, 0xba, 0x17, 0x53, 0x88, 0x88, 0x88,
> + 0x88, 0x88, 0x88, 0x80, 0x88, 0xba, 0x06, 0x42,
> + 0x88, 0x88, 0x88, 0x88, 0x88, 0x88, 0x23, 0x00,
> + 0x00, 0x02, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
> + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> + 0x00);
> + mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_EF, 0xff, 0xff, 0x01);
> +
> + return 0;
> +}
> +
> +static const struct drm_display_mode rg353v2_mode = {
> + .hdisplay = 640,
> + .hsync_start = 640 + 40,
> + .hsync_end = 640 + 40 + 2,
> + .htotal = 640 + 40 + 2 + 80,
> + .vdisplay = 480,
> + .vsync_start = 480 + 18,
> + .vsync_end = 480 + 18 + 2,
> + .vtotal = 480 + 18 + 2 + 28,
> + .clock = 24150,
> + .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> + .width_mm = 70,
> + .height_mm = 57,
> +};
> +
> +static const struct st7703_panel_desc rg353v2_desc = {
> + .mode = &rg353v2_mode,
> + .lanes = 4,
> + .mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
> + MIPI_DSI_MODE_NO_EOT_PACKET | MIPI_DSI_MODE_LPM,
> + .format = MIPI_DSI_FMT_RGB888,
> + .init_sequence = rg353v2_init_sequence,
> +};
> +
> static int st7703_enable(struct drm_panel *panel)
> {
> struct st7703 *ctx = panel_to_st7703(panel);
> @@ -615,6 +710,7 @@ static void st7703_remove(struct mipi_dsi_device *dsi)
> }
>
> static const struct of_device_id st7703_of_match[] = {
> + { .compatible = "anbernic,rg353v-panel-v2", .data = &rg353v2_desc },
> { .compatible = "rocktech,jh057n00900", .data = &jh057n00900_panel_desc },
> { .compatible = "xingbangda,xbd599", .data = &xbd599_desc },
> { /* sentinel */ }
> --
> 2.34.1
>
next prev parent reply other threads:[~2023-01-20 9:06 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-19 23:04 [PATCH 0/2] drm/panel: Add Anbernic RG353V-V2 Panel Chris Morgan
2023-01-19 23:04 ` [PATCH 1/2] dt-bindings: panel: Add compatible for Anbernic RG353V-V2 panel Chris Morgan
2023-01-20 8:19 ` Krzysztof Kozlowski
2023-01-20 9:05 ` Guido Günther
2023-01-19 23:04 ` [PATCH 2/2] drm/panel: st7703: Add support " Chris Morgan
2023-01-20 9:06 ` Guido Günther [this message]
2023-01-20 15:13 ` Chris Morgan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y8pZqPH0rDSfxhVr@qwark.sigxcpu.org \
--to=guido.gunther@puri.sm \
--cc=airlied@gmail.com \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=kernel@puri.sm \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=macroalpha82@gmail.com \
--cc=macromorgan@hotmail.com \
--cc=megous@megous.com \
--cc=robh+dt@kernel.org \
--cc=sam@ravnborg.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).