Re: [PATCH v7 2/8] pwm: pca9685: Support hardware readout

[Clemens Gruber <clemens.gruber@pqgruber.com>]

On Wed, Apr 07, 2021 at 07:31:35AM +0200, Uwe Kleine-König wrote:
> On Tue, Apr 06, 2021 at 06:41:34PM +0200, Clemens Gruber wrote:
> > Implements .get_state to read-out the current hardware state.
> > 
> > The hardware readout may return slightly different values than those
> > that were set in apply due to the limited range of possible prescale and
> > counter register values.
> > 
> > Also note that although the datasheet mentions 200 Hz as default
> > frequency when using the internal 25 MHz oscillator, the calculated
> > period from the default prescaler register setting of 30 is 5079040ns.
> > 
> > Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
> > ---
> > Changes since v6:
> > - Added a comment regarding the division (Suggested by Uwe)
> > - Rebased
> > 
> >  drivers/pwm/pwm-pca9685.c | 46 +++++++++++++++++++++++++++++++++++++++
> >  1 file changed, 46 insertions(+)
> > 
> > diff --git a/drivers/pwm/pwm-pca9685.c b/drivers/pwm/pwm-pca9685.c
> > index 5a2ce97e71fd..d4474c5ff96f 100644
> > --- a/drivers/pwm/pwm-pca9685.c
> > +++ b/drivers/pwm/pwm-pca9685.c
> > @@ -333,6 +333,51 @@ static int pca9685_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> >  	return 0;
> >  }
> >  
> > +static void pca9685_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> > +				  struct pwm_state *state)
> > +{
> > +	struct pca9685 *pca = to_pca(chip);
> > +	unsigned long long duty;
> > +	unsigned int val = 0;
> > +
> > +	/* Calculate (chip-wide) period from prescale value */
> > +	regmap_read(pca->regmap, PCA9685_PRESCALE, &val);
> > +	/*
> > +	 * PCA9685_OSC_CLOCK_MHZ is 25, i.e. an integer divider of 1000.
> > +	 * The following calculation is therefore only a multiplication
> > +	 * and we are not losing precision.
> > +	 */
> > +	state->period = (PCA9685_COUNTER_RANGE * 1000 / PCA9685_OSC_CLOCK_MHZ) *
> > +			(val + 1);
> > +
> > +	/* The (per-channel) polarity is fixed */
> > +	state->polarity = PWM_POLARITY_NORMAL;
> > +
> > +	if (pwm->hwpwm >= PCA9685_MAXCHAN) {
> > +		/*
> > +		 * The "all LEDs" channel does not support HW readout
> > +		 * Return 0 and disabled for backwards compatibility
> > +		 */
> > +		state->duty_cycle = 0;
> > +		state->enabled = false;
> > +		return;
> > +	}
> > +
> > +	duty = pca9685_pwm_get_duty(pca, pwm->hwpwm);
> > +
> > +	state->enabled = !!duty;
> > +	if (!state->enabled) {
> > +		state->duty_cycle = 0;
> > +		return;
> > +	} else if (duty == PCA9685_COUNTER_RANGE) {
> > +		state->duty_cycle = state->period;
> > +		return;
> > +	}
> > +
> > +	duty *= state->period;
> > +	state->duty_cycle = duty / PCA9685_COUNTER_RANGE;
> 
> Given that with duty = 0 the chip is still "on" and changing the duty
> will first complete the currently running period, I'd model duty=0 as
> enabled. This also simplifies the code a bit, to something like:
> 
> 
> 	state->enabled = true;
> 	duty = pca9685_pwm_get_duty(pca, pwm->hwpwm);
> 	state->duty_cycle = div_round_up(duty * state->period, PCA9685_COUNTER_RANGE);
> 
> (I'm using round-up here assuming apply uses round-down to get
> idempotency. In the current patch set state this is wrong however.)

So, in your opinion, every requested PWM of the pca9685 should always be
enabled by default (from the PWM core viewpoint) ?

And this wouldn't break the following because pwm_get_state does not
actually read out the hw state:
pwm_get_state -> enabled=true duty=0
pwm_apply_state -> enabled =false duty=0
pwm_get_state -> enabled=false duty=0

Thanks,
Clemens