Re: [PATCH v3 3/7] arm64: defconfig: enable drivers for TQ TQMa8MxML-MBa8Mx

[Abel Vesa <abel.vesa@nxp.com>]

On 21-12-01 08:29:44, Alexander Stein wrote:
> With the device tree in place, enable missing drivers as modules, if
> possible. PHY driver needs built-in for interrupt support.
> 
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Changes in v3:
> * None
> 
> Changes in v2:
> * Add interconnect driver for imx8mm and imx8mn
> 
>  arch/arm64/configs/defconfig | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index 0da6a944d5cd..44ce56dd2638 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -363,6 +363,7 @@ CONFIG_MICROSEMI_PHY=y
>  CONFIG_AT803X_PHY=y
>  CONFIG_REALTEK_PHY=y
>  CONFIG_ROCKCHIP_PHY=y
> +CONFIG_DP83867_PHY=y
>  CONFIG_VITESSE_PHY=y
>  CONFIG_USB_PEGASUS=m
>  CONFIG_USB_RTL8150=m
> @@ -397,6 +398,7 @@ CONFIG_TOUCHSCREEN_EDT_FT5X06=m
>  CONFIG_INPUT_MISC=y
>  CONFIG_INPUT_PM8941_PWRKEY=y
>  CONFIG_INPUT_PM8XXX_VIBRATOR=m
> +CONFIG_INPUT_PWM_BEEPER=m
>  CONFIG_INPUT_PWM_VIBRA=m
>  CONFIG_INPUT_HISI_POWERKEY=y
>  # CONFIG_SERIO_SERPORT is not set
> @@ -556,6 +558,7 @@ CONFIG_BATTERY_MAX17042=m
>  CONFIG_CHARGER_BQ25890=m
>  CONFIG_CHARGER_BQ25980=m
>  CONFIG_SENSORS_ARM_SCPI=y
> +CONFIG_SENSORS_JC42=m
>  CONFIG_SENSORS_LM90=m
>  CONFIG_SENSORS_PWM_FAN=m
>  CONFIG_SENSORS_RASPBERRYPI_HWMON=m
> @@ -793,6 +796,7 @@ CONFIG_SND_SOC_RT5659=m
>  CONFIG_SND_SOC_SIMPLE_AMPLIFIER=m
>  CONFIG_SND_SOC_SIMPLE_MUX=m
>  CONFIG_SND_SOC_TAS571X=m
> +CONFIG_SND_SOC_TLV320AIC32X4_I2C=m
>  CONFIG_SND_SOC_WCD934X=m
>  CONFIG_SND_SOC_WM8904=m
>  CONFIG_SND_SOC_WM8960=m
> @@ -908,6 +912,7 @@ CONFIG_RTC_DRV_DS1307=m
>  CONFIG_RTC_DRV_HYM8563=m
>  CONFIG_RTC_DRV_MAX77686=y
>  CONFIG_RTC_DRV_RK808=m
> +CONFIG_RTC_DRV_PCF85063=m
>  CONFIG_RTC_DRV_PCF85363=m
>  CONFIG_RTC_DRV_M41T80=m
>  CONFIG_RTC_DRV_RX8581=m
> @@ -1175,6 +1180,8 @@ CONFIG_SLIM_QCOM_NGD_CTRL=m
>  CONFIG_MUX_MMIO=y
>  CONFIG_INTERCONNECT=y
>  CONFIG_INTERCONNECT_IMX=m
> +CONFIG_INTERCONNECT_IMX8MM=m
> +CONFIG_INTERCONNECT_IMX8MN=m

Nope. The interconnect doesn't work without imx8m-ddrc
and imx-bus devfreq drivers. Those drivers do not work
yet. 

So please drop the interconnect configs for now.


>  CONFIG_INTERCONNECT_IMX8MQ=m
>  CONFIG_INTERCONNECT_QCOM=y
>  CONFIG_INTERCONNECT_QCOM_MSM8916=m
> -- 
> 2.25.1
>