[PATCH v10 00/12] Add soundcard support for sc7280 based platforms.

[PATCH v10 00/12] Add soundcard support for sc7280 based platforms.

[Srinivasa Rao Mandadapu]

This patch set is to add bolero digital macros, WCD and maxim codecs nodes
for audio on sc7280 based platforms.

This patch set depends on:
    -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=631506
    -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=601249
    -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=634203
    -- Clock reset control patches

Changes Since V9:
    -- Move wcd codec and digital codec nodes to sc7280-qcard file.
    -- Modify the reg property as per link number in sound node.
    -- Fix the us-euro pin control usage in wcd codec node.
    -- Move wcd pin control nodes to specific crd board files.
    -- Sort max98360a codec node in alphabetical order.
    -- Modify the commit messages.
Changes Since V8:
    -- Split patches as per sc7280 CRD revision 3, 4 and 5 boards.
    -- Add corresponding dt nodes for herobrine crd boards.
    -- Update dai-link node names as per dt-bindings in sound node.
    -- Add reg property in sound node as per dt-bindings which was removed in previous series.
    -- Fix typo errors.
    -- Update wcd codec pin control properties in board specific files.
Changes Since V7:
    -- Remove redundant interrupt names in soundwire node.
    -- Fix typo errors.
    -- Remove redundant reg property in sound node.
    -- Rebased on top of latest kernel tip.
Changes Since V6:
    -- Modify link-names and audio routing in a sound node.
    -- Move amp_en pin control node to appropriate consumer patch.
    -- Split patches as per digital macro codecs and board specific codecs and sort it.
    -- Modify label and node names to lpass specific.
Changes Since V5:
    -- Move soc specific bolero digital codec nodes to soc specific file.
    -- Bring wcd938x codec reset pin control and US/EURO HS selection nodes from other series.
    -- Change node name and remove redundant status property in sound node.
Changes Since V4:
    -- Update nodes in sorting order.
    -- Update DTS node names as per dt-bindings.
    -- Update Node properties in proper order.
    -- Update missing pinctrl properties like US/EURO HS selection, wcd reset control.
    -- Remove redundant labels.
    -- Remove unused size cells and address cells in tx macro node.
    -- Keep all same nodes at one place, which are defined in same file.
    -- Add max98360a codec node to herobrine board specific targets.
Changes Since V3:
    -- Move digital codec macro nodes to board specific dtsi file.
    -- Update pin controls in lpass cpu node.
    -- Update dependency patch list.
    -- Create patches on latest kernel.
Changes Since V2:
    -- Add power domains to digital codec macro nodes.
    -- Change clock node usage in lpass cpu node.
    -- Add codec mem clock to lpass cpu node.
    -- Modify the node names to be generic.
    -- Move sound and codec nodes to root node.
    -- sort dai links as per reg.
    -- Fix typo errors.
Changes Since V1:
    -- Update the commit message of cpu node patch.
    -- Add gpio control property to support Euro headset in wcd938x node.
    -- Fix clock properties in lpass cpu and digital codec macro node.

Srinivasa Rao Mandadapu (12):
  arm64: dts: qcom: sc7280: Add nodes for soundwire and va tx rx digital
    macro codecs
  arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD
    1.0/2.0 and IDP boards
  arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD
    3.0/3.1
  arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0/2.0 and
    IDP boards
  arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 3.0/3.1
  arm64: dts: qcom: sc7280: Add max98360a codec for CRD 1.0/2.0 and IDP
    boards
  arm64: dts: qcom: sc7280: herobrine: Add max98360a codec node
  arm64: dts: qcom: sc7280: Add lpass cpu node
  arm64: dts: qcom: sc7280: Enable lpass cpu node for CRD 1.0/2.0 and
    IDP boards.
  arm64: dts: qcom: sc7280: Enable lpass cpu node for CRD 3.0/3.1
  arm64: dts: qcom: sc7280: Add sound node for CRD 1.0/2.0 and IDP
    boards
  arm64: dts: qcom: sc7280: Add sound node for CRD 3.0/3.1

 arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts        |  37 ++++
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 150 +++++++++++++++
 arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi    |   8 +
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi          | 218 ++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi        |  75 ++++++++
 arch/arm64/boot/dts/qcom/sc7280.dtsi              | 190 +++++++++++++++++++
 6 files changed, 678 insertions(+)

-- 
2.7.4

[PATCH v10 01/12] arm64: dts: qcom: sc7280: Add nodes for soundwire and va tx rx digital macro codecs

[Srinivasa Rao Mandadapu]

SC7280 has VA, TX and RX macros with SoundWire Controllers to attach with
external codecs using soundwire masters. Add these nodes for sc7280 based
platforms audio use case.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 128 +++++++++++++++++++++++++++++++++++
 1 file changed, 128 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index fe500f4..9c46dc4 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2035,6 +2035,114 @@
 			#clock-cells = <1>;
 		};
 
+		lpass_rx_macro: codec@3200000 {
+			compatible = "qcom,sc7280-lpass-rx-macro";
+			reg = <0 0x03200000 0 0x1000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&lpass_rx_swr>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+				 <&lpass_va_macro>;
+			clock-names = "mclk", "npl", "fsgen";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
+		swr0: soundwire@3210000 {
+			compatible = "qcom,soundwire-v1.6.0";
+			reg = <0 0x03210000 0 0x2000>;
+
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lpass_rx_macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <0>;
+			qcom,dout-ports = <5>;
+
+			resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
+			reset-names = "swr_audio_cgcr";
+
+			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
+			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x3f 0x1f 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x01>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		lpass_tx_macro: codec@3220000 {
+			compatible = "qcom,sc7280-lpass-tx-macro";
+			reg = <0 0x03220000 0 0x1000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&lpass_tx_swr>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+				 <&lpass_va_macro>;
+			clock-names = "mclk", "npl", "fsgen";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
+		swr1: soundwire@3230000 {
+			compatible = "qcom,soundwire-v1.6.0";
+			reg = <0 0x03230000 0 0x2000>;
+
+			interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 130 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lpass_tx_macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <3>;
+			qcom,dout-ports = <0>;
+
+			resets = <&lpass_audiocc LPASS_AUDIO_SWR_TX_CGCR>;
+			reset-names = "swr_audio_cgcr";
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0x01 0x00 0x02>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-word-length =	/bits/ 8 <0xff 0x00 0xff>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-lane-control =	/bits/ 8 <0x00 0x01 0x00>;
+			qcom,port-offset = <1>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
 		lpass_audiocc: clock-controller@3300000 {
 			compatible = "qcom,sc7280-lpassaudiocc";
 			reg = <0 0x03300000 0 0x30000>;
@@ -2046,6 +2154,26 @@
 			#power-domain-cells = <1>;
 		};
 
+		lpass_va_macro: codec@3370000 {
+			compatible = "qcom,sc7280-lpass-va-macro";
+			reg = <0 0x03370000 0 0x1000>;
+
+			pinctrl-0 = <&lpass_dmic01>;
+			pinctrl-names = "default";
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>;
+			clock-names = "mclk";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
 		lpass_aon: clock-controller@3380000 {
 			compatible = "qcom,sc7280-lpassaoncc";
 			reg = <0 0x03380000 0 0x30000>;
-- 
2.7.4

[PATCH v10 02/12] arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD 1.0/2.0 and IDP boards

[Srinivasa Rao Mandadapu]

Enable rx, tx and va macro codecs and soundwire nodes on revision 3,
4 (aka CRD 1.0 and 2.0) and IDP boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 35 ++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 2f863c0..6cb5fc4 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -238,6 +238,19 @@
 	modem-init;
 };
 
+&lpass_rx_macro {
+	status = "okay";
+};
+
+&lpass_tx_macro {
+	status = "okay";
+};
+
+&lpass_va_macro {
+	status = "okay";
+	vdd-micb-supply = <&vreg_bob>;
+};
+
 &pcie1 {
 	status = "okay";
 	perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
@@ -298,6 +311,28 @@
 	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
 };
 
+&swr0 {
+	status = "okay";
+
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		#sound-dai-cells = <1>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		#sound-dai-cells = <1>;
+		qcom,tx-port-mapping = <1 2 3 4>;
+	};
+};
+
 &uart5 {
 	compatible = "qcom,geni-debug-uart";
 	status = "okay";
-- 
2.7.4

Re: [PATCH v10 02/12] arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD 1.0/2.0 and IDP boards

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:31PM +0530, Srinivasa Rao Mandadapu wrote:
> Enable rx, tx and va macro codecs and soundwire nodes on revision 3,
> 4 (aka CRD 1.0 and 2.0) and IDP boards.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v10 03/12] arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD 3.0/3.1

[Srinivasa Rao Mandadapu]

Enable rx, tx and va macro codecs and soundwire nodes for
CRD rev5+ (aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 20 ++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi        | 22 ++++++++++++++++++++++
 2 files changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index b06f61e..9348728 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -81,6 +81,18 @@ ap_ts_pen_1v8: &i2c13 {
 	};
 };
 
+&lpass_rx_macro {
+	status = "okay";
+};
+
+&lpass_tx_macro {
+	status = "okay";
+};
+
+&lpass_va_macro {
+	status = "okay";
+};
+
 /* For nvme */
 &pcie1 {
 	status = "okay";
@@ -101,6 +113,14 @@ ap_ts_pen_1v8: &i2c13 {
 	status = "okay";
 };
 
+&swr0 {
+	status = "okay";
+};
+
+&swr1 {
+	status = "okay";
+};
+
 /* PINCTRL - BOARD-SPECIFIC */
 
 /*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
index b833ba1..11d37cb 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -293,6 +293,10 @@
 	modem-init;
 };
 
+&lpass_va_macro {
+	vdd-micb-supply = <&vreg_bob>;
+};
+
 &pcie1_phy {
 	vdda-phy-supply = <&vreg_l10c_0p88>;
 	vdda-pll-supply = <&vreg_l6b_1p2>;
@@ -326,6 +330,24 @@
 	no-sdio;
 };
 
+&swr0 {
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		#sound-dai-cells = <1>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr1 {
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		#sound-dai-cells = <1>;
+		qcom,tx-port-mapping = <1 2 3 4>;
+	};
+};
+
 uart_dbg: &uart5 {
 	compatible = "qcom,geni-debug-uart";
 	status = "okay";
-- 
2.7.4

Re: [PATCH v10 03/12] arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD 3.0/3.1

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:32PM +0530, Srinivasa Rao Mandadapu wrote:
> Enable rx, tx and va macro codecs and soundwire nodes for
> CRD rev5+ (aka CRD 3.0/3.1) boards.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v10 04/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0/2.0 and IDP boards

[Srinivasa Rao Mandadapu]

Add wcd9385 codec node for audio use case on sc7280 based platforms
of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards.
Add tlmm gpio property for switching CTIA/OMTP Headset.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts | 14 ++++++++++
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi   | 43 ++++++++++++++++++++++++++++++
 2 files changed, 57 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
index 344338a..9c21207 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
@@ -87,6 +87,13 @@ ap_ts_pen_1v8: &i2c13 {
 	pins = "gpio51";
 };
 
+&wcd9385 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>;
+	pinctrl-1 = <&wcd_reset_n_sleep>, <&us_euro_hs_sel>;
+	us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+};
+
 &tlmm {
 	tp_int_odl: tp-int-odl {
 		pins = "gpio7";
@@ -105,4 +112,11 @@ ap_ts_pen_1v8: &i2c13 {
 		function = "gpio";
 		bias-disable;
 	};
+
+	us_euro_hs_sel: us-euro-hs-sel {
+		pins = "gpio81";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 6cb5fc4..72e6a6c 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -20,6 +20,34 @@
 		serial1 = &uart7;
 	};
 
+	wcd9385: audio-codec-1 {
+		compatible = "qcom,wcd9385-codec";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&wcd_reset_n>;
+		pinctrl-1 = <&wcd_reset_n_sleep>;
+
+		reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		vdd-rxtx-supply = <&vreg_l18b_1p8>;
+		vdd-io-supply = <&vreg_l18b_1p8>;
+		vdd-buck-supply = <&vreg_l17b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+							  500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		#sound-dai-cells = <1>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		label = "gpio-keys";
@@ -678,6 +706,21 @@
 		function = "gpio";
 		bias-pull-down;
 	};
+
+	wcd_reset_n: wcd-reset-n {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		output-high;
+	};
+
+	wcd_reset_n_sleep: wcd-reset-n-sleep {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		output-low;
+	};
 };
 
 &remoteproc_wpss {
-- 
2.7.4

Re: [PATCH v10 04/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0/2.0 and IDP boards

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:33PM +0530, Srinivasa Rao Mandadapu wrote:
> Add wcd9385 codec node for audio use case on sc7280 based platforms
> of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards.
> Add tlmm gpio property for switching CTIA/OMTP Headset.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v10 05/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 3.0/3.1

[Srinivasa Rao Mandadapu]

Add wcd9385 codec node for audio use case on CRD rev5+ (aka CRD 3.0/3.1)
boards. Add tlmm gpio property for switching CTIA/OMTP Headset.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts |  4 ++
 arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi        | 53 +++++++++++++++++++++++
 2 files changed, 57 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index 9348728..46480b2 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -121,6 +121,10 @@ ap_ts_pen_1v8: &i2c13 {
 	status = "okay";
 };
 
+&wcd9385 {
+	status = "okay";
+};
+
 /* PINCTRL - BOARD-SPECIFIC */
 
 /*
diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
index 11d37cb..a7f0b1f 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -29,6 +29,37 @@
 		serial0 = &uart5;
 		serial1 = &uart7;
 	};
+
+	wcd9385: audio-codec-1 {
+		compatible = "qcom,wcd9385-codec";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>;
+		pinctrl-1 = <&wcd_reset_n_sleep>, <&us_euro_hs_sel>;
+
+		reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+		us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		vdd-rxtx-supply = <&vreg_l18b_1p8>;
+		vdd-io-supply = <&vreg_l18b_1p8>;
+		vdd-buck-supply = <&vreg_l17b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+							  500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		#sound-dai-cells = <1>;
+
+		status = "disabled";
+	};
 };
 
 &apps_rsc {
@@ -566,4 +597,26 @@ mos_bt_uart: &uart7 {
 		bias-pull-up;
 		drive-strength = <2>;
 	};
+
+	us_euro_hs_sel: us-euro-hs-sel {
+		pins = "gpio81";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	wcd_reset_n: wcd-reset-n {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		output-high;
+	};
+
+	wcd_reset_n_sleep: wcd-reset-n-sleep {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		output-low;
+	};
 };
-- 
2.7.4

Re: [PATCH v10 05/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 3.0/3.1

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:34PM +0530, Srinivasa Rao Mandadapu wrote:
> Add wcd9385 codec node for audio use case on CRD rev5+ (aka CRD 3.0/3.1)
> boards. Add tlmm gpio property for switching CTIA/OMTP Headset.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v10 06/12] arm64: dts: qcom: sc7280: Add max98360a codec for CRD 1.0/2.0 and IDP boards

[Srinivasa Rao Mandadapu]

Add max98360a codec node for audio use case on revision 3, 4
(aka CRD 1.0 and 2.0) and IDP boards.
Add amp_en node for max98360a codec pin control.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 72e6a6c..8503bd1 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -20,6 +20,14 @@
 		serial1 = &uart7;
 	};
 
+	max98360a: audio-codec-0 {
+		compatible = "maxim,max98360a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&amp_en>;
+		sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <0>;
+	};
+
 	wcd9385: audio-codec-1 {
 		compatible = "qcom,wcd9385-codec";
 		pinctrl-names = "default", "sleep";
@@ -624,6 +632,12 @@
 };
 
 &tlmm {
+	amp_en: amp-en {
+		pins = "gpio63";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
 	bt_en: bt-en {
 		pins = "gpio85";
 		function = "gpio";
-- 
2.7.4

[PATCH v10 07/12] arm64: dts: qcom: sc7280: herobrine: Add max98360a codec node

[Srinivasa Rao Mandadapu]

Add max98360a codec node for audio use case on all herobrine boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index d58045d..5da2246 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -295,6 +295,14 @@
 
 	/* BOARD-SPECIFIC TOP LEVEL NODES */
 
+	max98360a: audio-codec-0 {
+		compatible = "maxim,max98360a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&amp_en>;
+		sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <0>;
+	};
+
 	pwmleds {
 		compatible = "pwm-leds";
 		status = "disabled";
-- 
2.7.4

Re: [PATCH v10 07/12] arm64: dts: qcom: sc7280: herobrine: Add max98360a codec node

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:36PM +0530, Srinivasa Rao Mandadapu wrote:
> Add max98360a codec node for audio use case on all herobrine boards.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v10 08/12] arm64: dts: qcom: sc7280: Add lpass cpu node

[Srinivasa Rao Mandadapu]

Add lpass cpu node for audio on sc7280 based platforms.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 62 ++++++++++++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 9c46dc4..9b764c7 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -21,6 +21,7 @@
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/reset/qcom,sdm845-pdc.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/sound/qcom,lpass.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -2195,6 +2196,67 @@
 			#power-domain-cells = <1>;
 		};
 
+		lpass_cpu: audio@3987000 {
+			compatible = "qcom,sc7280-lpass-cpu";
+
+			reg = <0 0x03987000 0 0x68000>,
+			      <0 0x03b00000 0 0x29000>,
+			      <0 0x03260000 0 0xc000>,
+			      <0 0x03280000 0 0x29000>,
+			      <0 0x03340000 0 0x29000>,
+			      <0 0x0336c000 0 0x3000>;
+			reg-names = "lpass-hdmiif",
+				    "lpass-lpaif",
+				    "lpass-rxtx-cdc-dma-lpm",
+				    "lpass-rxtx-lpaif",
+				    "lpass-va-lpaif",
+				    "lpass-va-cdc-dma-lpm";
+
+			iommus = <&apps_smmu 0x1820 0>,
+				 <&apps_smmu 0x1821 0>,
+				 <&apps_smmu 0x1832 0>;
+
+			power-domains =	<&rpmhpd SC7280_LCX>;
+			power-domain-names = "lcx";
+			required-opps = <&rpmhpd_opp_nom>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_AUDIO_HM_H_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_EXT_MCLK0_CLK>,
+				 <&lpasscore LPASS_CORE_CC_SYSNOC_MPORT_CORE_CLK>,
+				 <&lpasscore LPASS_CORE_CC_EXT_IF0_IBIT_CLK>,
+				 <&lpasscore LPASS_CORE_CC_EXT_IF1_IBIT_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM0_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM1_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM2_CLK>,
+				 <&lpass_aon LPASS_AON_CC_VA_MEM0_CLK>;
+			clock-names = "aon_cc_audio_hm_h",
+				      "audio_cc_ext_mclk0",
+				      "core_cc_sysnoc_mport_core",
+				      "core_cc_ext_if0_ibit",
+				      "core_cc_ext_if1_ibit",
+				      "audio_cc_codec_mem",
+				      "audio_cc_codec_mem0",
+				      "audio_cc_codec_mem1",
+				      "audio_cc_codec_mem2",
+				      "aon_cc_va_mem0";
+
+			#sound-dai-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "lpass-irq-lpaif",
+					  "lpass-irq-hdmi",
+					  "lpass-irq-vaif",
+					  "lpass-irq-rxtxif";
+
+			status = "disabled";
+		};
+
 		lpass_hm: clock-controller@3c00000 {
 			compatible = "qcom,sc7280-lpasshm";
 			reg = <0 0x3c00000 0 0x28>;
-- 
2.7.4

[PATCH v10 09/12] arm64: dts: qcom: sc7280: Enable lpass cpu node for CRD 1.0/2.0 and IDP boards.

[Srinivasa Rao Mandadapu]

Enable lpass cpu node and add pin control and dai-links for audio on sc7280
based platforms of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 8503bd1..c09a17d 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -274,6 +274,34 @@
 	modem-init;
 };
 
+&lpass_cpu {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mi2s1_data0>, <&mi2s1_sclk>, <&mi2s1_ws>;
+
+	dai-link@1 {
+		reg = <MI2S_SECONDARY>;
+		qcom,playback-sd-lines = <0>;
+	};
+
+	dai-link@5 {
+		reg = <LPASS_DP_RX>;
+	};
+
+	dai-link@6 {
+		reg = <LPASS_CDC_DMA_RX0>;
+	};
+
+	dai-link@19 {
+		reg = <LPASS_CDC_DMA_TX3>;
+	};
+
+	dai-link@25 {
+		reg = <LPASS_CDC_DMA_VA_TX0>;
+	};
+};
+
 &lpass_rx_macro {
 	status = "okay";
 };
-- 
2.7.4

[PATCH v10 10/12] arm64: dts: qcom: sc7280: Enable lpass cpu node for CRD 3.0/3.1

[Srinivasa Rao Mandadapu]

Enable lpass cpu node and add pin control and dai-links for audio on
sc7280 based platforms of rev5+ (aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 28 +++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index 46480b2..ba13d62 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -81,6 +81,34 @@ ap_ts_pen_1v8: &i2c13 {
 	};
 };
 
+&lpass_cpu {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mi2s1_data0>, <&mi2s1_sclk>, <&mi2s1_ws>;
+
+	dai-link@1 {
+		reg = <MI2S_SECONDARY>;
+		qcom,playback-sd-lines = <0>;
+	};
+
+	dai-link@5 {
+		reg = <LPASS_DP_RX>;
+	};
+
+	dai-link@6 {
+		reg = <LPASS_CDC_DMA_RX0>;
+	};
+
+	dai-link@19 {
+		reg = <LPASS_CDC_DMA_TX3>;
+	};
+
+	dai-link@25 {
+		reg = <LPASS_CDC_DMA_VA_TX0>;
+	};
+};
+
 &lpass_rx_macro {
 	status = "okay";
 };
-- 
2.7.4

[PATCH v10 11/12] arm64: dts: qcom: sc7280: Add sound node for CRD 1.0/2.0 and IDP boards

[Srinivasa Rao Mandadapu]

Add dt nodes for sound card support on revision 3, 4
(aka CRD 1.0 and 2.0) and IDP boards, which is using WCD9385 headset
playback, capture, I2S speaker playback and DMICs via VA macro.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts | 23 +++++++
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi   | 98 ++++++++++++++++++++++++++++++
 2 files changed, 121 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
index 9c21207..dddb505 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
@@ -87,6 +87,29 @@ ap_ts_pen_1v8: &i2c13 {
 	pins = "gpio51";
 };
 
+&sound {
+	audio-routing =
+		"IN1_HPHL", "HPHL_OUT",
+		"IN2_HPHR", "HPHR_OUT",
+		"AMIC1", "MIC BIAS1",
+		"AMIC2", "MIC BIAS2",
+		"VA DMIC0", "MIC BIAS1",
+		"VA DMIC1", "MIC BIAS1",
+		"VA DMIC2", "MIC BIAS3",
+		"VA DMIC3", "MIC BIAS3",
+		"TX SWR_ADC0", "ADC1_OUTPUT",
+		"TX SWR_ADC1", "ADC2_OUTPUT",
+		"TX SWR_ADC2", "ADC3_OUTPUT",
+		"TX SWR_DMIC0", "DMIC1_OUTPUT",
+		"TX SWR_DMIC1", "DMIC2_OUTPUT",
+		"TX SWR_DMIC2", "DMIC3_OUTPUT",
+		"TX SWR_DMIC3", "DMIC4_OUTPUT",
+		"TX SWR_DMIC4", "DMIC5_OUTPUT",
+		"TX SWR_DMIC5", "DMIC6_OUTPUT",
+		"TX SWR_DMIC6", "DMIC7_OUTPUT",
+		"TX SWR_DMIC7", "DMIC8_OUTPUT";
+};
+
 &wcd9385 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>;
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index c09a17d..6b6ade8 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -85,6 +85,104 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&nvme_pwren>;
 	};
+
+	sound: sound {
+		compatible = "google,sc7280-herobrine";
+		model = "sc7280-wcd938x-max98360a-1mic";
+
+		audio-routing =
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC1", "MIC BIAS1",
+			"AMIC2", "MIC BIAS2",
+			"VA DMIC0", "MIC BIAS3",
+			"VA DMIC1", "MIC BIAS3",
+			"VA DMIC2", "MIC BIAS1",
+			"VA DMIC3", "MIC BIAS1",
+			"TX SWR_ADC0", "ADC1_OUTPUT",
+			"TX SWR_ADC1", "ADC2_OUTPUT",
+			"TX SWR_ADC2", "ADC3_OUTPUT",
+			"TX SWR_DMIC0", "DMIC1_OUTPUT",
+			"TX SWR_DMIC1", "DMIC2_OUTPUT",
+			"TX SWR_DMIC2", "DMIC3_OUTPUT",
+			"TX SWR_DMIC3", "DMIC4_OUTPUT",
+			"TX SWR_DMIC4", "DMIC5_OUTPUT",
+			"TX SWR_DMIC5", "DMIC6_OUTPUT",
+			"TX SWR_DMIC6", "DMIC7_OUTPUT",
+			"TX SWR_DMIC7", "DMIC8_OUTPUT";
+
+		qcom,msm-mbhc-hphl-swh = <1>;
+		qcom,msm-mbhc-gnd-swh = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#sound-dai-cells = <0>;
+
+		dai-link@0 {
+			link-name = "MAX98360A";
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_SECONDARY>;
+			};
+
+			codec {
+				sound-dai = <&max98360a>;
+			};
+		};
+
+		dai-link@1 {
+			link-name = "DisplayPort";
+			reg = <1>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_DP_RX>;
+			};
+
+			codec {
+				sound-dai = <&mdss_dp>;
+			};
+		};
+
+		dai-link@2 {
+			link-name = "WCD9385 Playback";
+			reg = <2>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_RX0>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 0>, <&swr0 0>, <&lpass_rx_macro 0>;
+			};
+		};
+
+		dai-link@3 {
+			link-name = "WCD9385 Capture";
+			reg = <3>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_TX3>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 1>, <&swr1 0>, <&lpass_tx_macro 0>;
+			};
+		};
+
+		dai-link@4 {
+			link-name = "DMIC";
+			reg = <4>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_VA_TX0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_va_macro 0>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
-- 
2.7.4

Re: [PATCH v10 11/12] arm64: dts: qcom: sc7280: Add sound node for CRD 1.0/2.0 and IDP boards

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:40PM +0530, Srinivasa Rao Mandadapu wrote:
> Add dt nodes for sound card support on revision 3, 4
> (aka CRD 1.0 and 2.0) and IDP boards, which is using WCD9385 headset
> playback, capture, I2S speaker playback and DMICs via VA macro.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v10 12/12] arm64: dts: qcom: sc7280: Add sound node for CRD 3.0/3.1

[Srinivasa Rao Mandadapu]

Add dt nodes for sound card support on rev5+ (aka CRD 3.0/3.1) boards,
which is using WCD9385 headset playback, capture, I2S speaker playback
and DMICs via VA macro.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 98 +++++++++++++++++++++++
 1 file changed, 98 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index ba13d62..1a18ab17 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -12,6 +12,104 @@
 / {
 	model = "Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+)";
 	compatible = "google,hoglin", "qcom,sc7280";
+
+	sound: sound {
+		compatible = "google,sc7280-herobrine";
+		model = "sc7280-wcd938x-max98360a-1mic";
+
+		audio-routing =
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC1", "MIC BIAS1",
+			"AMIC2", "MIC BIAS2",
+			"VA DMIC0", "MIC BIAS1",
+			"VA DMIC1", "MIC BIAS1",
+			"VA DMIC2", "MIC BIAS3",
+			"VA DMIC3", "MIC BIAS3",
+			"TX SWR_ADC0", "ADC1_OUTPUT",
+			"TX SWR_ADC1", "ADC2_OUTPUT",
+			"TX SWR_ADC2", "ADC3_OUTPUT",
+			"TX SWR_DMIC0", "DMIC1_OUTPUT",
+			"TX SWR_DMIC1", "DMIC2_OUTPUT",
+			"TX SWR_DMIC2", "DMIC3_OUTPUT",
+			"TX SWR_DMIC3", "DMIC4_OUTPUT",
+			"TX SWR_DMIC4", "DMIC5_OUTPUT",
+			"TX SWR_DMIC5", "DMIC6_OUTPUT",
+			"TX SWR_DMIC6", "DMIC7_OUTPUT",
+			"TX SWR_DMIC7", "DMIC8_OUTPUT";
+
+		qcom,msm-mbhc-hphl-swh = <1>;
+		qcom,msm-mbhc-gnd-swh = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#sound-dai-cells = <0>;
+
+		dai-link@0 {
+			link-name = "MAX98360A";
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_SECONDARY>;
+			};
+
+			codec {
+				sound-dai = <&max98360a>;
+			};
+		};
+
+		dai-link@1 {
+			link-name = "DisplayPort";
+			reg = <1>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_DP_RX>;
+			};
+
+			codec {
+				sound-dai = <&mdss_dp>;
+			};
+		};
+
+		dai-link@2 {
+			link-name = "WCD9385 Playback";
+			reg = <2>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_RX0>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 0>, <&swr0 0>, <&lpass_rx_macro 0>;
+			};
+		};
+
+		dai-link@3 {
+			link-name = "WCD9385 Capture";
+			reg = <3>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_TX3>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 1>, <&swr1 0>, <&lpass_tx_macro 0>;
+			};
+		};
+
+		dai-link@4 {
+			link-name = "DMIC";
+			reg = <4>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_VA_TX0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_va_macro 0>;
+			};
+		};
+	};
 };
 
 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
-- 
2.7.4

Re: [PATCH v10 12/12] arm64: dts: qcom: sc7280: Add sound node for CRD 3.0/3.1

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:41PM +0530, Srinivasa Rao Mandadapu wrote:
> Add dt nodes for sound card support on rev5+ (aka CRD 3.0/3.1) boards,
> which is using WCD9385 headset playback, capture, I2S speaker playback
> and DMICs via VA macro.
> 
> Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
> Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
> Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v10 00/12] Add soundcard support for sc7280 based platforms.

[Matthias Kaehlcke]

On Fri, Apr 22, 2022 at 07:38:29PM +0530, Srinivasa Rao Mandadapu wrote:
> This patch set is to add bolero digital macros, WCD and maxim codecs nodes
> for audio on sc7280 based platforms.
> 
> This patch set depends on:
>     -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=631506

There's a newer version (v10) [1]

which should be ready to land now that 'Add pin control support for lpass
sc7280' [2] has landed in Linus' pinctrl tree

>     -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=601249

These are flagged as 'Queued', so probably landing soon.

>     -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=634203

There is a newer version [3] which seems ready to land.

>     -- Clock reset control patches

What is this? I don't think I have seen an upstream version of this.
Please provide a link, or if it hasn't be posted upstream yet make sure
it is done ASAP.

[1]https://patchwork.kernel.org/project/linux-arm-msm/list/?series=632316
[2] https://patchwork.kernel.org/project/linux-arm-msm/list/?series=633019&state=*
[3] https://patchwork.kernel.org/project/linux-arm-msm/patch/1650621734-10297-1-git-send-email-quic_srivasam@quicinc.com/

Re: [PATCH v10 00/12] Add soundcard support for sc7280 based platforms.

[Srinivasa Rao Mandadapu]

On 4/26/2022 12:00 AM, Matthias Kaehlcke wrote:
> On Fri, Apr 22, 2022 at 07:38:29PM +0530, Srinivasa Rao Mandadapu wrote:
>> This patch set is to add bolero digital macros, WCD and maxim codecs nodes
>> for audio on sc7280 based platforms.
>>
>> This patch set depends on:
>>      -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=631506
> There's a newer version (v10) [1]
>
> which should be ready to land now that 'Add pin control support for lpass
> sc7280' [2] has landed in Linus' pinctrl tree
Yes. It's ready for landing. But will post the next version, as per new 
herobrine dts files for rev5+ boards.
>
>>      -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=601249
> These are flagged as 'Queued', so probably landing soon.
Yes. They may land soon.
>
>>      -- https://patchwork.kernel.org/project/linux-arm-msm/list/?series=634203
> There is a newer version [3] which seems ready to land.
Yes. It's reviewed.
>
>>      -- Clock reset control patches
> What is this? I don't think I have seen an upstream version of this.
> Please provide a link, or if it hasn't be posted upstream yet make sure
> it is done ASAP.
These patches are yet to upstream by Clock team. Requested them to do ASAP.
>
> [1]https://patchwork.kernel.org/project/linux-arm-msm/list/?series=632316
> [2] https://patchwork.kernel.org/project/linux-arm-msm/list/?series=633019&state=*
> [3] https://patchwork.kernel.org/project/linux-arm-msm/patch/1650621734-10297-1-git-send-email-quic_srivasam@quicinc.com/