devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Vinod Koul <vkoul@kernel.org>
To: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Kishon Vijay Abraham I <kishon@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Heiko Stuebner <heiko@sntech.de>,
	linux-phy@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, kernel@collabora.com
Subject: Re: [PATCHv2 5/7] phy: phy-rockchip-inno-usb2: add rk3588 phy tuning support
Date: Wed, 12 Apr 2023 22:14:08 +0530	[thread overview]
Message-ID: <ZDbf2At0EakD09af@matsya> (raw)
In-Reply-To: <20230403202307.120562-6-sebastian.reichel@collabora.com>

On 03-04-23, 22:23, Sebastian Reichel wrote:
> On RK3588 some registers need to be tweaked to support waking up from
> suspend when a USB device is plugged into a port from a suspended PHY.
> Without this change USB devices only work when they are plugged at
> boot time.
> 
> Apart from that it optimizes settings to avoid devices toggling
> between fullspeed and highspeed mode.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 63 +++++++++++++++++++
>  1 file changed, 63 insertions(+)
> 
> diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
> index 3a78c5bf11d4..9f6d09da7fbd 100644
> --- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
> +++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
> @@ -33,6 +33,8 @@
>  #define SCHEDULE_DELAY		(60 * HZ)
>  #define OTG_SCHEDULE_DELAY	(2 * HZ)
>  
> +struct rockchip_usb2phy;
> +
>  enum rockchip_usb2phy_port_id {
>  	USB2PHY_PORT_OTG,
>  	USB2PHY_PORT_HOST,
> @@ -163,6 +165,7 @@ struct rockchip_usb2phy_port_cfg {
>   * struct rockchip_usb2phy_cfg - usb-phy configuration.
>   * @reg: the address offset of grf for usb-phy config.
>   * @num_ports: specify how many ports that the phy has.
> + * @phy_tuning: phy default parameters tuning.
>   * @clkout_ctl: keep on/turn off output clk of phy.
>   * @port_cfgs: usb-phy port configurations.
>   * @chg_det: charger detection registers.
> @@ -170,6 +173,7 @@ struct rockchip_usb2phy_port_cfg {
>  struct rockchip_usb2phy_cfg {
>  	unsigned int	reg;
>  	unsigned int	num_ports;
> +	int (*phy_tuning)(struct rockchip_usb2phy *rphy);
>  	struct usb2phy_reg	clkout_ctl;
>  	const struct rockchip_usb2phy_port_cfg	port_cfgs[USB2PHY_NUM_PORTS];
>  	const struct rockchip_chg_det_reg	chg_det;
> @@ -1400,6 +1404,12 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
>  		goto disable_clks;
>  	}
>  
> +	if (rphy->phy_cfg->phy_tuning) {
> +		ret = rphy->phy_cfg->phy_tuning(rphy);
> +		if (ret)
> +			goto disable_clks;
> +	}
> +
>  	index = 0;
>  	for_each_available_child_of_node(np, child_np) {
>  		struct rockchip_usb2phy_port *rport = &rphy->ports[index];
> @@ -1468,6 +1478,55 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
>  	return ret;
>  }
>  
> +static int rk3588_usb2phy_tuning(struct rockchip_usb2phy *rphy)
> +{
> +	int ret = 0;

superfluous init

> +	bool usb3otg = false;
> +	/*
> +	 * utmi_termselect = 1'b1 (en FS terminations)
> +	 * utmi_xcvrselect = 2'b01 (FS transceiver)
> +	 */
> +	int suspend_cfg = 0x14;
> +
> +	if (rphy->phy_cfg->reg == 0x0000 || rphy->phy_cfg->reg == 0x4000) {
> +		/* USB2 config for USB3_0 and USB3_1 */
> +		suspend_cfg |= 0x01; /* utmi_opmode = 2'b01 (no-driving) */
> +		usb3otg = true;
> +	} else if (rphy->phy_cfg->reg == 0x8000 || rphy->phy_cfg->reg == 0xc000) {
> +		/* USB2 config for USB2_0 and USB2_1 */
> +		suspend_cfg |= 0x00; /* utmi_opmode = 2'b00 (normal) */
> +	} else {
> +		return -EINVAL;
> +	}
> +
> +	/* Deassert SIDDQ to power on analog block */
> +	ret = regmap_write(rphy->grf, 0x0008, GENMASK(29, 29) | 0x0000);
> +	if (ret)
> +		return ret;
> +
> +	/* Do reset after exit IDDQ mode */
> +	ret = rockchip_usb2phy_reset(rphy);
> +	if (ret)
> +		return ret;
> +
> +	/* suspend configuration */
> +	ret |= regmap_write(rphy->grf, 0x000c, GENMASK(20, 16) | suspend_cfg);
> +
> +	/* HS DC Voltage Level Adjustment 4'b1001 : +5.89% */
> +	ret |= regmap_write(rphy->grf, 0x0004, GENMASK(27, 24) | 0x0900);
> +
> +	/* HS Transmitter Pre-Emphasis Current Control 2'b10 : 2x */
> +	ret |= regmap_write(rphy->grf, 0x0008, GENMASK(20, 19) | 0x0010);
> +
> +	if (!usb3otg)
> +		return ret;
> +
> +	/* Pullup iddig pin for USB3_0 OTG mode */
> +	ret |= regmap_write(rphy->grf, 0x0010, GENMASK(17, 16) | 0x0003);
> +
> +	return ret;
> +}
> +
>  static const struct rockchip_usb2phy_cfg rk3228_phy_cfgs[] = {
>  	{
>  		.reg = 0x760,
> @@ -1785,6 +1844,7 @@ static const struct rockchip_usb2phy_cfg rk3588_phy_cfgs[] = {
>  	{
>  		.reg = 0x0000,
>  		.num_ports	= 1,
> +		.phy_tuning	= rk3588_usb2phy_tuning,
>  		.clkout_ctl	= { 0x0000, 0, 0, 1, 0 },
>  		.port_cfgs	= {
>  			[USB2PHY_PORT_OTG] = {
> @@ -1821,6 +1881,7 @@ static const struct rockchip_usb2phy_cfg rk3588_phy_cfgs[] = {
>  	{
>  		.reg = 0x4000,
>  		.num_ports	= 1,
> +		.phy_tuning	= rk3588_usb2phy_tuning,
>  		.clkout_ctl	= { 0x0000, 0, 0, 1, 0 },
>  		.port_cfgs	= {
>  			[USB2PHY_PORT_OTG] = {
> @@ -1857,6 +1918,7 @@ static const struct rockchip_usb2phy_cfg rk3588_phy_cfgs[] = {
>  	{
>  		.reg = 0x8000,
>  		.num_ports	= 1,
> +		.phy_tuning	= rk3588_usb2phy_tuning,
>  		.clkout_ctl	= { 0x0000, 0, 0, 1, 0 },
>  		.port_cfgs	= {
>  			[USB2PHY_PORT_HOST] = {
> @@ -1877,6 +1939,7 @@ static const struct rockchip_usb2phy_cfg rk3588_phy_cfgs[] = {
>  	{
>  		.reg = 0xc000,
>  		.num_ports	= 1,
> +		.phy_tuning	= rk3588_usb2phy_tuning,
>  		.clkout_ctl	= { 0x0000, 0, 0, 1, 0 },
>  		.port_cfgs	= {
>  			[USB2PHY_PORT_HOST] = {
> -- 
> 2.39.2

-- 
~Vinod

  reply	other threads:[~2023-04-12 16:45 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-04-03 20:23 [PATCHv2 0/7] phy-rockchip-inno-usb2: add RK3588 support Sebastian Reichel
2023-04-03 20:23 ` [PATCHv2 1/7] dt-bindings: soc: rockchip: add rk3588 usb2phy syscon Sebastian Reichel
2023-04-04 14:26   ` Rob Herring
2023-04-03 20:23 ` [PATCHv2 2/7] dt-bindings: phy: rockchip,inno-usb2phy: add rk3588 Sebastian Reichel
2023-04-04 14:27   ` Rob Herring
2023-04-03 20:23 ` [PATCHv2 3/7] phy: phy-rockchip-inno-usb2: add rk3588 support Sebastian Reichel
2023-04-03 20:23 ` [PATCHv2 4/7] phy: phy-rockchip-inno-usb2: add reset support Sebastian Reichel
2023-04-03 20:23 ` [PATCHv2 5/7] phy: phy-rockchip-inno-usb2: add rk3588 phy tuning support Sebastian Reichel
2023-04-12 16:44   ` Vinod Koul [this message]
2023-04-03 20:23 ` [PATCHv2 6/7] phy: phy-rockchip-inno-usb2: simplify phy clock handling Sebastian Reichel
2023-04-03 20:23 ` [PATCHv2 7/7] phy: phy-rockchip-inno-usb2: simplify getting match data Sebastian Reichel
2023-05-02  9:37 ` (subset) [PATCHv2 0/7] phy-rockchip-inno-usb2: add RK3588 support Heiko Stuebner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ZDbf2At0EakD09af@matsya \
    --to=vkoul@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=heiko@sntech.de \
    --cc=kernel@collabora.com \
    --cc=kishon@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=robh+dt@kernel.org \
    --cc=sebastian.reichel@collabora.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).