From: Vinod Koul <vkoul@kernel.org>
To: Frank Li <Frank.Li@nxp.com>
Cc: devicetree@vger.kernel.org, fushi.peng@nxp.com,
imx@lists.linux.dev, kernel@pengutronix.de, kishon@kernel.org,
krzysztof.kozlowski+dt@linaro.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-phy@lists.infradead.org,
robh+dt@kernel.org, s.hauer@pengutronix.de, shawnguo@kernel.org
Subject: Re: [PATCH v4 4/6] phy: cadence: salvo: add .set_mode API
Date: Tue, 16 May 2023 22:05:06 +0530 [thread overview]
Message-ID: <ZGOwukxGLdRHNL0l@matsya> (raw)
In-Reply-To: <20230516154329.3155031-5-Frank.Li@nxp.com>
On 16-05-23, 11:43, Frank Li wrote:
> From: Peter Chen <peter.chen@nxp.com>
>
> For NXP platform design, the PHY can't know VBUS well, it causes the FSM
> in controller seeing the disconnection at L1 use case. With .set_mode API
> introduced, the controller driver could force PHY seeing B Session VALID
> when it is at the device mode (VBUS is there), and keep FSM working well.
>
> Signed-off-by: Peter Chen <peter.chen@nxp.com>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> drivers/phy/cadence/phy-cadence-salvo.c | 29 +++++++++++++++++++++++++
> 1 file changed, 29 insertions(+)
>
> diff --git a/drivers/phy/cadence/phy-cadence-salvo.c b/drivers/phy/cadence/phy-cadence-salvo.c
> index b9866dc146ce..41616f786321 100644
> --- a/drivers/phy/cadence/phy-cadence-salvo.c
> +++ b/drivers/phy/cadence/phy-cadence-salvo.c
> @@ -92,6 +92,7 @@
> /* USB2 PHY register definition */
> #define UTMI_REG15 0xaf
> #define UTMI_AFE_RX_REG5 0x12
> +#define UTMI_AFE_BC_REG4 0x29
>
> /* TB_ADDR_TX_RCVDETSC_CTRL */
> #define RXDET_IN_P3_32KHZ BIT(0)
> @@ -105,6 +106,9 @@
> /* 0us, txvalid is ready just after HS/FS transmitters have powered up */
> #define TXVALID_GATE_THRESHOLD_HS_0US (BIT(4) | BIT(5))
>
> +#define SET_B_SESSION_VALID (BIT(6) | BIT(5))
> +#define CLR_B_SESSION_VALID (BIT(6))
> +
> struct cdns_reg_pairs {
> u16 val;
> u32 off;
> @@ -124,6 +128,13 @@ struct cdns_salvo_phy {
> };
>
> static const struct of_device_id cdns_salvo_phy_of_match[];
> +static const struct cdns_salvo_data cdns_nxp_salvo_data;
> +
> +static bool cdns_is_nxp_phy(struct cdns_salvo_phy *salvo_phy)
> +{
> + return salvo_phy->data == &cdns_nxp_salvo_data;
> +}
> +
> static u16 cdns_salvo_read(struct cdns_salvo_phy *salvo_phy, u32 offset, u32 reg)
> {
> return (u16)readl(salvo_phy->base + offset +
> @@ -273,11 +284,29 @@ static int cdns_salvo_phy_power_off(struct phy *phy)
> return 0;
> }
>
> +static int cdns_salvo_set_mode(struct phy *phy, enum phy_mode mode, int submode)
> +{
> + struct cdns_salvo_phy *salvo_phy = phy_get_drvdata(phy);
> +
> + if (!cdns_is_nxp_phy(salvo_phy))
> + return 0;
> +
> + if (mode == PHY_MODE_INVALID)
> + cdns_salvo_write(salvo_phy, USB2_PHY_OFFSET, UTMI_AFE_BC_REG4,
> + CLR_B_SESSION_VALID);
> + else if (mode == PHY_MODE_USB_DEVICE)
> + cdns_salvo_write(salvo_phy, USB2_PHY_OFFSET, UTMI_AFE_BC_REG4,
> + SET_B_SESSION_VALID);
no else?
> +
> + return 0;
return success even when mode is not handled?
> +}
> +
> static const struct phy_ops cdns_salvo_phy_ops = {
> .init = cdns_salvo_phy_init,
> .power_on = cdns_salvo_phy_power_on,
> .power_off = cdns_salvo_phy_power_off,
> .owner = THIS_MODULE,
> + .set_mode = cdns_salvo_set_mode,
> };
>
> static int cdns_salvo_phy_probe(struct platform_device *pdev)
> --
> 2.34.1
--
~Vinod
next prev parent reply other threads:[~2023-05-16 16:35 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-16 15:43 [PATCH v4 0/6] phy: cadence: salvo: some fixes and workarounds Frank Li
2023-05-16 15:43 ` [PATCH v4 1/6] phy: cadence: salvo: add access for USB2PHY Frank Li
2023-05-16 15:43 ` [PATCH v4 2/6] phy: cadence: salvo: decrease delay value to zero for txvalid Frank Li
2023-05-16 15:43 ` [PATCH v4 3/6] phy: cadence: salvo: add bist fix Frank Li
2023-05-16 16:34 ` Vinod Koul
2023-05-16 15:43 ` [PATCH v4 4/6] phy: cadence: salvo: add .set_mode API Frank Li
2023-05-16 16:35 ` Vinod Koul [this message]
2023-05-16 15:43 ` [PATCH v4 5/6] phy: cadence: salvo: Add cdns,usb2-disconnect-threshold-microvolt property Frank Li
2023-05-16 15:43 ` [PATCH v4 6/6] dt-bindings: phy: cdns,salvo: add property cdns,usb2-disconnect-threshold-microvolt Frank Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ZGOwukxGLdRHNL0l@matsya \
--to=vkoul@kernel.org \
--cc=Frank.Li@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=fushi.peng@nxp.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=kishon@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).