[PATCH 0/2] arm64: dts: qcom: Add missing nodes to X1E80100 base dtsi and CRD dts

[PATCH 0/2] arm64: dts: qcom: Add missing nodes to X1E80100 base dtsi and CRD dts

[Abel Vesa]

This patchset adds all missing nodes in order to describe the entire
platform. Most of these have dependencies on multimedia clock
controllers and so the entire patchset depends on the clock controllers
patchset:
https://lore.kernel.org/all/20231212-x1e80100-clock-controllers-v1-0-0de1af44dcb3@linaro.org/

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
Abel Vesa (2):
      arm64: dts: qcom: x1e80100: Add all missing nodes
      arm64: dts: qcom: x1e80100: Add missing nodes for CRD

 arch/arm64/boot/dts/qcom/x1e80100-crd.dts |  303 +++++++
 arch/arm64/boot/dts/qcom/x1e80100.dtsi    | 1282 ++++++++++++++++++++++++++++-
 2 files changed, 1580 insertions(+), 5 deletions(-)
---
base-commit: 10ef05bf74d045c6636bcbaf2cc60aabbda8a54c
change-id: 20231201-x1e80100-dts-missing-nodes-a09f1ed99999

Best regards,
-- 
Abel Vesa <abel.vesa@linaro.org>

[PATCH 1/2] arm64: dts: qcom: x1e80100: Add all missing nodes

[Abel Vesa]

Add all missing nodes which describe entire X1E80100 platform.

Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 1282 +++++++++++++++++++++++++++++++-
 1 file changed, 1277 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index da691e2f3209..61cc36554eab 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -4,11 +4,16 @@
  */
 
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,x1e80100-dispcc.h>
 #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
+#include <dt-bindings/clock/qcom,x1e80100-gpucc.h>
+#include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/interconnect/qcom,icc.h>
 #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
 #include <dt-bindings/power/qcom,rpmhpd.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -662,6 +667,58 @@ smem_mem: smem@ffe00000 {
 		};
 	};
 
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <443>, <429>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-cdsp {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <94>, <432>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_cdsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_cdsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
 	soc: soc@0 {
 		compatible = "simple-bus";
 
@@ -677,13 +734,13 @@ gcc: clock-controller@100000 {
 			clocks = <&bi_tcxo_div2>,
 				 <&sleep_clk>,
 				 <0>,
+				 <&pcie4_phy>,
 				 <0>,
+				 <&pcie6a_phy>,
 				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>;
+				 <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
+				 <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
+				 <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
 
 			power-domains = <&rpmhpd RPMHPD_CX>;
 			#clock-cells = <1>;
@@ -691,6 +748,17 @@ gcc: clock-controller@100000 {
 			#power-domain-cells = <1>;
 		};
 
+		ipcc: mailbox@408000 {
+			compatible = "qcom,x1e80100-ipcc", "qcom,ipcc";
+			reg = <0 0x00408000 0 0x1000>;
+
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			#mbox-cells = <2>;
+		};
+
 		gpi_dma2: dma-controller@800000 {
 			compatible = "qcom,x1e80100-gpi-dma", "qcom,sm6350-gpi-dma";
 			reg = <0 0x00800000 0 0x60000>;
@@ -2428,6 +2496,165 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
 			};
 		};
 
+		gpucc: clock-controller@3d90000 {
+			compatible = "qcom,x1e80100-gpucc";
+			reg = <0 0x3d90000 0 0xa000>;
+			clocks = <&bi_tcxo_div2>,
+				 <&gcc GCC_GPU_GPLL0_CPH_CLK_SRC>,
+				 <&gcc GCC_GPU_GPLL0_DIV_CPH_CLK_SRC>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		camcc: clock-controller@ade0000 {
+			compatible = "qcom,x1e80100-camcc";
+			reg = <0 0xade0000 0 0x20000>;
+			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&bi_tcxo_div2>,
+				 <&bi_tcxo_ao_div2>,
+				 <&sleep_clk>;
+			power-domains = <&rpmhpd RPMHPD_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			status = "disabled";
+		};
+
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,x1e80100-dispcc";
+			reg = <0 0xaf00000 0 0x20000>;
+			clocks = <&bi_tcxo_div2>,
+				 <&bi_tcxo_ao_div2>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&sleep_clk>,
+				 <0>, /* dsi0 */
+				 <0>,
+				 <0>, /* dsi1 */
+				 <0>,
+				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp0 */
+				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>, /* dp0 */
+				 <0>, /* dp1 */
+				 <0>,
+				 <0>, /* dp2 */
+				 <0>,
+				 <&mdss_dp3_phy 0>, /* dp3 */
+				 <&mdss_dp3_phy 1>;
+			power-domains = <&rpmhpd RPMHPD_MMCX>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		usb_1_ss0_hsphy: phy@fd3000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0x0 0x0fd3000 0x0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss0_qmpphy: phy@fd5000 {
+			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
+			reg = <0 0xfd5000 0 0x4000>;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc GCC_USB_1_PHY_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB4_0_DP0_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss1_hsphy: phy@fd9000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0x0 0x0fd9000 0x0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss1_qmpphy: phy@fda000 {
+			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
+			reg = <0 0xfda000 0 0x4000>;
+
+			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc GCC_USB30_SEC_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
+				 <&gcc GCC_USB4_1_DP0_PHY_SEC_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss2_hsphy: phy@fde000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0x0 0x0fde000 0x0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_TERT_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss2_qmpphy: phy@fdf000 {
+			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
+			reg = <0 0xfdf000 0 0x4000>;
+
+			clocks = <&gcc GCC_USB3_TERT_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_TERT_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_TERT_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc GCC_USB30_TERT_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_TERT_BCR>,
+				 <&gcc GCC_USB4_2_DP0_PHY_TERT_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
 		cnoc_main: interconnect@1500000 {
 			compatible = "qcom,x1e80100-cnoc-main";
 			reg = <0 0x1500000 0 0x14400>;
@@ -2536,12 +2763,204 @@ mmss_noc: interconnect@1780000 {
 			#interconnect-cells = <2>;
 		};
 
+		pcie6a: pci@1bf8000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-x1e80100";
+			reg = <0x0 0x01bf8000 0x0 0x3000>,
+			      <0x0 0x70000000 0x0 0xf1d>,
+			      <0x0 0x70000f20 0x0 0xa8>,
+			      <0x0 0x70001000 0x0 0x1000>,
+			      <0x0 0x70100000 0x0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <7>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 843 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 844 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 845 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 772 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_6A_AUX_CLK>,
+				 <&gcc GCC_PCIE_6A_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_6A_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_6A_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_6A_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_SOUTH_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "noc_aggr_south_sf";
+
+			assigned-clocks = <&gcc GCC_PCIE_6A_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_south_anoc MASTER_PCIE_6A 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_6A 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			resets = <&gcc GCC_PCIE_6A_BCR>,
+				<&gcc GCC_PCIE_6A_LINK_DOWN_BCR>;
+			reset-names = "pci", "link_down";
+
+			power-domains = <&gcc GCC_PCIE_6A_GDSC>;
+
+			phys = <&pcie6a_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie6a_phy: phy@1bfc000 {
+			compatible = "qcom,x1e80100-qmp-gen4x2-pcie-phy";
+			reg = <0x0 0x01bfc000 0x0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_6A_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_6A_CFG_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_6A_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_6A_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_6A_PHY_BCR>,
+				 <&gcc GCC_PCIE_6A_NOCSR_COM_PHY_BCR>;
+			reset-names = "phy", "phy_nocsr";
+
+			assigned-clocks = <&gcc GCC_PCIE_6A_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc GCC_PCIE_6_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie6a_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie4: pci@1c08000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-x1e80100";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x7c000000 0 0xf1d>,
+			      <0 0x7c000f40 0 0xa8>,
+			      <0 0x7c001000 0 0x1000>,
+			      <0 0x7c100000 0 0x100000>,
+			      <0 0x01c0b000 0 0x1000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x7c200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x7c300000 0x0 0x7c300000 0x0 0x3d00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <5>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0", "msi1", "msi2", "msi3";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
+				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_4_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_4_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "noc_aggr_south_sf";
+
+			assigned-clocks = <&gcc GCC_PCIE_4_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_south_anoc MASTER_PCIE_4 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_4 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			resets = <&gcc GCC_PCIE_4_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc GCC_PCIE_4_GDSC>;
+
+			phys = <&pcie4_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie4_phy: phy@1c0e000 {
+			compatible = "qcom,x1e80100-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
+				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_4_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_4_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_4_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_4_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc GCC_PCIE_4_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie4_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0 0x01f40000 0 0x20000>;
 			#hwlock-cells = <1>;
 		};
 
+		tcsr: clock-controller@1fc0000 {
+			compatible = "qcom,x1e80100-tcsr", "syscon";
+			reg = <0 0x01fc0000 0 0x30000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
 		gem_noc: interconnect@26400000 {
 			compatible = "qcom,x1e80100-gem-noc";
 			reg = <0 0x26400000 0 0x311200>;
@@ -2587,6 +3006,739 @@ lpass_lpicx_noc: interconnect@7430000 {
 			#interconnect-cells = <2>;
 		};
 
+		usb_2_hsphy: phy@88e0000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0x0 0x088e0000 0x0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_USB20_HS_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss2: usb@a0f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a0f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_TERT_AXI_CLK>,
+				 <&gcc GCC_USB30_TERT_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_TERT_AXI_CLK>,
+				 <&gcc GCC_USB30_TERT_SLEEP_CLK>,
+				 <&gcc GCC_USB30_TERT_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_TERT_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_TERT_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 10 IRQ_TYPE_EDGE_RISING>,
+					      <&pdc 57 IRQ_TYPE_EDGE_RISING>,
+					      <&pdc 58 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc GCC_USB30_TERT_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_TERT_BCR>;
+
+			interconnects = <&usb_south_anoc MASTER_USB3_2 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_2 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_1_ss2_dwc3: usb@a000000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a000000 0 0xcd00>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x14a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+				phys = <&usb_1_ss2_hsphy>, <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy", "usb3-phy";
+
+				port {
+					usb_1_ss2_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_2: usb@a2f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a2f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB2_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB20_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB2_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB20_SLEEP_CLK>,
+				 <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB20_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 50 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 49 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "pwr_event",
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq";
+
+			power-domains = <&gcc GCC_USB20_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB20_PRIM_BCR>;
+
+			interconnects = <&usb_north_anoc MASTER_USB2 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB2 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_2_dwc3: usb@a200000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a200000 0 0xcd00>;
+				interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x14e0 0x0>;
+				phys = <&usb_2_hsphy>;
+				phy-names = "usb2-phy";
+
+				port {
+					usb_2_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_1_ss0: usb@a6f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_USB_ANOC_NORTH_AHB_CLK>,
+				 <&gcc GCC_CFG_NOC_USB_ANOC_SOUTH_AHB_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_RISING>,
+					      <&pdc 61 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "pwr_event",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_1_ss0_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1420 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+				phys = <&usb_1_ss0_hsphy>, <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy", "usb3-phy";
+
+				port {
+					usb_1_ss0_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_1_ss1: usb@a8f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a8f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 47 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 11 IRQ_TYPE_EDGE_RISING>,
+					      <&pdc 60 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "pwr_event",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc GCC_USB30_SEC_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_SEC_BCR>;
+
+			interconnects = <&usb_south_anoc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_1_ss1_dwc3: usb@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a800000 0 0xcd00>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1460 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+				phys = <&usb_1_ss1_hsphy>, <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy", "usb3-phy";
+
+				port {
+					usb_1_ss1_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,x1e80100-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+			assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK_SRC>;
+			assigned-clock-parents = <&dispcc DISP_CC_PLL0>;
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			interconnects = <&mmss_noc MASTER_MDP 0 &gem_noc SLAVE_LLCC 0>,
+					<&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "mdp0-mem",
+					     "mdp1-mem";
+
+			power-domains = <&dispcc DISP_CC_MDSS_CORE_GDSC>;
+
+			iommus = <&apps_smmu 0x1c00 0x2>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,x1e80100-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp",
+					    "vbif";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&gcc GCC_DISP_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
+					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_intf0_out: endpoint {
+							remote-endpoint = <&mdss_dp0_in>;
+						};
+					};
+
+					port@4 {
+						reg = <4>;
+
+						mdss_intf4_out: endpoint {
+							remote-endpoint = <&mdss_dp1_in>;
+						};
+					};
+
+					port@5 {
+						reg = <5>;
+
+						mdss_intf5_out: endpoint {
+							remote-endpoint = <&mdss_dp3_in>;
+						};
+					};
+
+					port@6 {
+						reg = <6>;
+
+						mdss_intf6_out: endpoint {
+							remote-endpoint = <&mdss_dp2_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-325000000 {
+						opp-hz = /bits/ 64 <325000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-375000000 {
+						opp-hz = /bits/ 64 <375000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-514000000 {
+						opp-hz = /bits/ 64 <514000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp0: displayport-controller@ae90000 {
+				compatible = "qcom,x1e80100-dp";
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0x600>,
+				      <0 0xae91000 0 0x400>,
+				      <0 0xae91400 0 0x400>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <12>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
+				clock-names = "core_iface", "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				operating-points-v2 = <&mdss_dp0_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp0_in: endpoint {
+							remote-endpoint = <&mdss_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dp0_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp1: displayport-controller@ae98000 {
+				compatible = "qcom,x1e80100-dp";
+				reg = <0 0xae98000 0 0x200>,
+				      <0 0xae98200 0 0x200>,
+				      <0 0xae98400 0 0x600>,
+				      <0 0xae99000 0 0x400>,
+				      <0 0xae99400 0 0x400>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <13>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
+				clock-names = "core_iface", "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface", "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				phys = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				operating-points-v2 = <&mdss_dp1_opp_table>;
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp1_in: endpoint {
+							remote-endpoint = <&mdss_intf4_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp1_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dp1_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp2: displayport-controller@ae9a000 {
+				compatible = "qcom,x1e80100-dp";
+				reg = <0 0xae9a000 0 0x200>,
+				      <0 0xae9a200 0 0x200>,
+				      <0 0xae9a400 0 0x600>,
+				      <0 0xae9b000 0 0x400>,
+				      <0 0xae9b400 0 0x400>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
+				clock-names = "core_iface", "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface", "stream_pixel";
+				interrupt-parent = <&mdss>;
+				interrupts = <14>;
+				phys = <&mdss_dp2_phy>;
+				phy-names = "dp";
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dp2_phy 0>, <&mdss_dp2_phy 1>;
+				operating-points-v2 = <&mdss_dp2_opp_table>;
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dp2_in: endpoint {
+							remote-endpoint = <&mdss_intf6_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+					};
+				};
+
+				mdss_dp2_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp3: displayport-controller@aea0000 {
+				compatible = "qcom,x1e80100-dp", "qcom,sm8350-dp";
+				reg = <0 0xaea0000 0 0x200>,
+				      <0 0xaea0200 0 0x200>,
+				      <0 0xaea0400 0 0x600>,
+				      <0 0xaea1000 0 0x400>,
+				      <0 0xaea1400 0 0x400>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
+				clock-names = "core_iface", "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface", "stream_pixel";
+				interrupt-parent = <&mdss>;
+				interrupts = <15>;
+				phys = <&mdss_dp3_phy>;
+				phy-names = "dp";
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dp3_phy 0>, <&mdss_dp3_phy 1>;
+				operating-points-v2 = <&mdss_dp3_opp_table>;
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp3_in: endpoint {
+							remote-endpoint = <&mdss_intf5_out>;
+
+							link-frequencies = /bits/ 64 <8100000000>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+					};
+				};
+
+				mdss_dp3_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+		};
+
+		mdss_dp2_phy: phy@aec2a00 {
+			compatible = "qcom,x1e80100-dp-phy";
+			reg = <0 0x0aec2a00 0 0x19c>,
+			      <0 0x0aec2200 0 0xec>,
+			      <0 0x0aec2600 0 0xec>,
+			      <0 0x0aec2000 0 0x1c8>;
+
+			clocks = <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>,
+				 <&dispcc DISP_CC_MDSS_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
+
+			power-domains = <&rpmhpd RPMHPD_MX>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		mdss_dp3_phy: phy@aec5a00 {
+			compatible = "qcom,x1e80100-dp-phy";
+			reg = <0 0x0aec5a00 0 0x19c>,
+			      <0 0x0aec5200 0 0xec>,
+			      <0 0x0aec5600 0 0xec>,
+			      <0 0x0aec5000 0 0x1c8>;
+
+			clocks = <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>,
+				 <&dispcc DISP_CC_MDSS_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
+
+			power-domains = <&rpmhpd RPMHPD_MX>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,x1e80100-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
@@ -2599,6 +3751,18 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		aoss_qmp: power-management@c300000 {
+			compatible = "qcom,x1e80100-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x400>;
+			interrupt-parent = <&ipcc>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+		};
+
+
 		tlmm: pinctrl@f100000 {
 			compatible = "qcom,x1e80100-tlmm";
 			reg = <0 0x0f100000 0 0xf00000>;
@@ -3492,6 +4656,29 @@ frame@1780d000 {
 			};
 		};
 
+		cpucp_mbox: mailbox@18830000 {
+			compatible = "qcom,x1e80100-cpucp-mbox", "qcom,cpucp-mbox";
+			reg = <0 0x18830000 0 0x300>, <0 0x17430000 0 0x4C08>;
+
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+
+			#mbox-cells = <1>;
+		};
+
+		sram: sram@18b4e000 {
+			compatible = "mmio-sram";
+			reg = <0x0 0x18b4e000 0x0 0x400>;
+			ranges = <0x0 0x0 0x18b4e000 0x400>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			cpu_scp_lpri: scmi-shmem@0 {
+				compatible = "arm,scmi-shmem";
+				reg = <0x0 0x400>;
+			};
+		};
+
 		system-cache-controller@25000000 {
 			compatible = "qcom,x1e80100-llcc";
 			reg = <0 0x25000000 0 0x200000>,
@@ -3514,6 +4701,91 @@ system-cache-controller@25000000 {
 				    "llcc_broadcast_base";
 			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		remoteproc_adsp: remoteproc@30000000 {
+			compatible = "qcom,x1e80100-adsp-pas";
+			reg = <0x0 0x30000000 0x0 0x100>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd RPMHPD_LCX>,
+					<&rpmhpd RPMHPD_LMX>;
+			power-domain-names = "lcx", "lmx";
+
+			interconnects = <&lpass_lpicx_noc MASTER_LPASS_PROC 0 &mc_virt SLAVE_EBI1 0>;
+
+			memory-region = <&adspslpi_mem>, <&q6_adsp_dtb_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+			};
+		};
+
+		remoteproc_cdsp: remoteproc@32300000 {
+			compatible = "qcom,x1e80100-cdsp-pas";
+			reg = <0x0 0x32300000 0x0 0x1400000>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd RPMHPD_CX>,
+					<&rpmhpd RPMHPD_MXC>,
+					<&rpmhpd RPMHPD_NSP>;
+			power-domain-names = "cx", "mxc", "nsp";
+
+			interconnects = <&nsp_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;
+
+			memory-region = <&cdsp_mem>, <&q6_cdsp_dtb_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_cdsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "cdsp";
+				qcom,remote-pid = <5>;
+			};
+		};
 	};
 
 	timer {

-- 
2.34.1

Re: [PATCH 1/2] arm64: dts: qcom: x1e80100: Add all missing nodes

[Konrad Dybcio]

On 12/12/23 11:24, Abel Vesa wrote:
> Add all missing nodes which describe entire X1E80100 platform.
"all" doesn't really mean all :|

couple of patch-wide observations below

[...]

>   
> +		gpucc: clock-controller@3d90000 {
> +			compatible = "qcom,x1e80100-gpucc";
> +			reg = <0 0x3d90000 0 0xa000>;
Please make sure the address part is padded to 8 hex digits
[...]

> +		usb_1_ss2_hsphy: phy@fde000 {
> +			compatible = "qcom,x1e80100-snps-eusb2-phy",
> +				     "qcom,sm8550-snps-eusb2-phy";
> +			reg = <0x0 0x0fde000 0x0 0x154>;
and please choose 0x0 vs 0 and stick to one (which seems to
be 0 in this file)

[...]

> +		pcie6a: pci@1bf8000 {
> +			device_type = "pci";
> +			compatible = "qcom,pcie-x1e80100";
> +			reg = <0x0 0x01bf8000 0x0 0x3000>,
> +			      <0x0 0x70000000 0x0 0xf1d>,
> +			      <0x0 0x70000f20 0x0 0xa8>,
> +			      <0x0 0x70001000 0x0 0x1000>,
> +			      <0x0 0x70100000 0x0 0x100000>;
> +			reg-names = "parf", "dbi", "elbi", "atu", "config";
one per line, please

> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x100000>,
> +				 <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;
> +			bus-range = <0x00 0xff>;
> +
> +			dma-coherent;
> +
> +			linux,pci-domain = <7>;
> +			num-lanes = <2>;
> +
> +			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 0 843 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc 0 0 0 844 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc 0 0 0 845 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc 0 0 0 772 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
you can drop these comments
[...]

> +				clocks = <&gcc GCC_DISP_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> +					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
> +					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				clock-names = "bus",
> +					      "nrt_bus",
> +					      "iface",
> +					      "lut",
> +					      "core",
> +					      "vsync";
you probably should list the ROT clock here too
[...]

> +		cpucp_mbox: mailbox@18830000 {
> +			compatible = "qcom,x1e80100-cpucp-mbox", "qcom,cpucp-mbox";
This is not upstream

> +			reg = <0 0x18830000 0 0x300>, <0 0x17430000 0 0x4C08>;
lowercase hex

Konrad

Re: [PATCH 1/2] arm64: dts: qcom: x1e80100: Add all missing nodes

[Abel Vesa]

On 23-12-12 17:21:19, Konrad Dybcio wrote:
> 
> 
> On 12/12/23 11:24, Abel Vesa wrote:
> > Add all missing nodes which describe entire X1E80100 platform.
> "all" doesn't really mean all :|
> 

Well, all the nodes where we have support working (for now).

But I'll re-word it to say "add some missing nodes".

> couple of patch-wide observations below
> 
> [...]
> 
> > +		gpucc: clock-controller@3d90000 {
> > +			compatible = "qcom,x1e80100-gpucc";
> > +			reg = <0 0x3d90000 0 0xa000>;
> Please make sure the address part is padded to 8 hex digits

Will do.

> [...]
> 
> > +		usb_1_ss2_hsphy: phy@fde000 {
> > +			compatible = "qcom,x1e80100-snps-eusb2-phy",
> > +				     "qcom,sm8550-snps-eusb2-phy";
> > +			reg = <0x0 0x0fde000 0x0 0x154>;
> and please choose 0x0 vs 0 and stick to one (which seems to
> be 0 in this file)

I'll use 0x0 in all reg as I think this is more consistent.

> 
> [...]
> 
> > +		pcie6a: pci@1bf8000 {
> > +			device_type = "pci";
> > +			compatible = "qcom,pcie-x1e80100";
> > +			reg = <0x0 0x01bf8000 0x0 0x3000>,
> > +			      <0x0 0x70000000 0x0 0xf1d>,
> > +			      <0x0 0x70000f20 0x0 0xa8>,
> > +			      <0x0 0x70001000 0x0 0x1000>,
> > +			      <0x0 0x70100000 0x0 0x100000>;
> > +			reg-names = "parf", "dbi", "elbi", "atu", "config";
> one per line, please

Will do.

> 
> > +			#address-cells = <3>;
> > +			#size-cells = <2>;
> > +			ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x100000>,
> > +				 <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;
> > +			bus-range = <0x00 0xff>;
> > +
> > +			dma-coherent;
> > +
> > +			linux,pci-domain = <7>;
> > +			num-lanes = <2>;
> > +
> > +			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>;
> > +			interrupt-names = "msi";
> > +
> > +			#interrupt-cells = <1>;
> > +			interrupt-map-mask = <0 0 0 0x7>;
> > +			interrupt-map = <0 0 0 1 &intc 0 0 0 843 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> > +					<0 0 0 2 &intc 0 0 0 844 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> > +					<0 0 0 3 &intc 0 0 0 845 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> > +					<0 0 0 4 &intc 0 0 0 772 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> you can drop these comments

Will do.

> [...]
> 
> > +				clocks = <&gcc GCC_DISP_AHB_CLK>,
> > +					 <&gcc GCC_DISP_HF_AXI_CLK>,
> > +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> > +					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
> > +					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > +				clock-names = "bus",
> > +					      "nrt_bus",
> > +					      "iface",
> > +					      "lut",
> > +					      "core",
> > +					      "vsync";
> you probably should list the ROT clock here too

Will look into it.

> [...]
> 
> > +		cpucp_mbox: mailbox@18830000 {
> > +			compatible = "qcom,x1e80100-cpucp-mbox", "qcom,cpucp-mbox";
> This is not upstream

It's a new driver, so bindings patches will come with it.

> 
> > +			reg = <0 0x18830000 0 0x300>, <0 0x17430000 0 0x4C08>;
> lowercase hex

Will do.

> 
> Konrad

Re: [PATCH 1/2] arm64: dts: qcom: x1e80100: Add all missing nodes

[Krzysztof Kozlowski]

On 14/12/2023 16:33, Abel Vesa wrote:
>>
>>> +		cpucp_mbox: mailbox@18830000 {
>>> +			compatible = "qcom,x1e80100-cpucp-mbox", "qcom,cpucp-mbox";
>> This is not upstream
> 
> It's a new driver, so bindings patches will come with it.

Driver does not have to, but all bindings must be posted or applied when
the DTS is sent. Otherwise we will start new release with warnings already.

If bindings are not ready, postpone the node.

Best regards,
Krzysztof

Re: [PATCH 1/2] arm64: dts: qcom: x1e80100: Add all missing nodes

[Abel Vesa]

On 23-12-14 17:33:54, Abel Vesa wrote:
> On 23-12-12 17:21:19, Konrad Dybcio wrote:
> > 
> > 
> > On 12/12/23 11:24, Abel Vesa wrote:
> > > Add all missing nodes which describe entire X1E80100 platform.
> > "all" doesn't really mean all :|
> > 

[...]

> > 
> > > +				clocks = <&gcc GCC_DISP_AHB_CLK>,
> > > +					 <&gcc GCC_DISP_HF_AXI_CLK>,
> > > +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > > +					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> > > +					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
> > > +					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > > +				clock-names = "bus",
> > > +					      "nrt_bus",
> > > +					      "iface",
> > > +					      "lut",
> > > +					      "core",
> > > +					      "vsync";
> > you probably should list the ROT clock here too
> 
> Will look into it.
> 

There is no ROT clock.

[PATCH 2/2] arm64: dts: qcom: x1e80100: Add missing nodes for CRD

[Abel Vesa]

Add all missing nodes for the X1E80100 CRD reference device.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 303 ++++++++++++++++++++++++++++++
 1 file changed, 303 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index c209ae59c6b5..4f7f83d49847 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -22,6 +22,72 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_role_switch>;
+					};
+				};
+			};
+		};
+
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_role_switch>;
+					};
+				};
+			};
+		};
+
+		connector@2 {
+			compatible = "usb-c-connector";
+			reg = <2>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss2_in: endpoint {
+						remote-endpoint = <&usb_1_ss2_role_switch>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 
@@ -403,10 +469,144 @@ vreg_l3j_0p8: ldo3 {
 	};
 };
 
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpad_default>;
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&kybd_default>;
+		wakeup-source;
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts0_default>;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp3 {
+	compatible = "qcom,x1e80100-dp";
+	/delete-property/ #sound-dai-cells;
+
+	data-lanes = <0 1 2 3>;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+			mdss_dp3_out: endpoint {
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a {
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
 &qupv3_2 {
 	status = "okay";
 };
 
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/adsp.mbn",
+			"qcom/x1e80100/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/cdsp.mbn",
+			"qcom/x1e80100/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <34 2>, /* Unused */
 			       <44 4>, /* SPI (TPM) */
@@ -418,9 +618,112 @@ edp_reg_en: edp-reg-en-state {
 		drive-strength = <16>;
 		bias-disable;
 	};
+
+	kybd_default: kybd-default-state {
+		int-n-pins {
+			pins = "gpio67";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	tpad_default: tpad-default-state {
+		int-n-pins {
+			pins = "gpio3";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	ts0_default: ts0-default-state {
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n-pins {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
 };
 
 &uart21 {
 	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss0_role_switch {
+	remote-endpoint = <&pmic_glink_ss0_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss1_role_switch {
+	remote-endpoint = <&pmic_glink_ss1_in>;
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss2_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss2_role_switch {
+	remote-endpoint = <&pmic_glink_ss2_in>;
+};

-- 
2.34.1

Re: [PATCH 2/2] arm64: dts: qcom: x1e80100: Add missing nodes for CRD

[Konrad Dybcio]

On 12/12/23 11:24, Abel Vesa wrote:
> Add all missing nodes for the X1E80100 CRD reference device.
> 
> Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
[...]

> +
> +	kybd_default: kybd-default-state {
> +		int-n-pins {
You can remove this level of indentation

Konrad