Re: [PATCH 2/2] media: gc2145: implement basic dvp bus support

[Sakari Ailus <sakari.ailus@linux.intel.com>]

Hi Andrey,

On Sun, Feb 18, 2024 at 01:03:08AM +0300, Andrey Skvortsov wrote:
> Tested on PinePhone with libcamera-based GNOME screenshot.
> 
> Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
> ---
>  drivers/media/i2c/gc2145.c | 117 ++++++++++++++++++++++++++++---------
>  1 file changed, 90 insertions(+), 27 deletions(-)
> 
> diff --git a/drivers/media/i2c/gc2145.c b/drivers/media/i2c/gc2145.c
> index bef7b0e056a8..9a70b8d504e1 100644
> --- a/drivers/media/i2c/gc2145.c
> +++ b/drivers/media/i2c/gc2145.c
> @@ -39,6 +39,10 @@
>  #define GC2145_REG_ANALOG_MODE1	CCI_REG8(0x17)
>  #define GC2145_REG_OUTPUT_FMT	CCI_REG8(0x84)
>  #define GC2145_REG_SYNC_MODE	CCI_REG8(0x86)
> +#define GC2145_SYNC_MODE_VSYNC_POL	BIT(0)
> +#define GC2145_SYNC_MODE_HSYNC_POL	BIT(1)
> +#define GC2145_SYNC_MODE_OPCLK_POL	BIT(2)
> +#define GC2145_SYNC_MODE_OPCLK_GATE	BIT(3)
>  #define GC2145_SYNC_MODE_COL_SWITCH	BIT(4)
>  #define GC2145_SYNC_MODE_ROW_SWITCH	BIT(5)
>  #define GC2145_REG_BYPASS_MODE	CCI_REG8(0x89)
> @@ -53,6 +57,12 @@
>  #define GC2145_REG_GLOBAL_GAIN	CCI_REG8(0xb0)
>  #define GC2145_REG_CHIP_ID	CCI_REG16(0xf0)
>  #define GC2145_REG_PAD_IO	CCI_REG8(0xf2)
> +#define GC2145_REG_PLL_MODE1	CCI_REG8(0xf7)
> +#define GC2145_REG_PLL_MODE2	CCI_REG8(0xf8)
> +#define GC2145_REG_CM_MODE	CCI_REG8(0xf9)
> +#define GC2145_REG_CLK_DIV_MODE	CCI_REG8(0xfa)
> +#define GC2145_REG_ANALOG_PWC	CCI_REG8(0xfc)
> +#define GC2145_REG_PAD_IO	CCI_REG8(0xf2)
>  #define GC2145_REG_PAGE_SELECT	CCI_REG8(0xfe)
>  /* Page 3 */
>  #define GC2145_REG_DPHY_ANALOG_MODE1	CCI_REG8(0x01)
> @@ -598,6 +608,7 @@ struct gc2145 {
>  	struct v4l2_subdev sd;
>  	struct media_pad pad;
>  
> +	struct v4l2_fwnode_endpoint ep; /* the parsed DT endpoint info */
>  	struct regmap *regmap;
>  	struct clk *xclk;
>  
> @@ -612,6 +623,11 @@ struct gc2145 {
>  	const struct gc2145_mode *mode;
>  };
>  
> +static inline bool gc2145_is_csi2(const struct gc2145 *gc2145)
> +{
> +	return gc2145->ep.bus_type == V4L2_MBUS_CSI2_DPHY;

This is used in a single place. Could you move this comparison there?

> +}
> +
>  static inline struct gc2145 *to_gc2145(struct v4l2_subdev *_sd)
>  {
>  	return container_of(_sd, struct gc2145, sd);
> @@ -773,6 +789,38 @@ static int gc2145_set_pad_format(struct v4l2_subdev *sd,
>  	return 0;
>  }
>  
> +static int gc2145_config_dvp_mode(struct gc2145 *gc2145,
> +				   const struct gc2145_format *gc2145_format)
> +{
> +	int ret = 0;
> +	u64 sync_mode;
> +	int flags;
> +
> +	flags = gc2145->ep.bus.parallel.flags;
> +
> +	ret = cci_read(gc2145->regmap, GC2145_REG_SYNC_MODE, &sync_mode, NULL);
> +	if (ret)
> +		return ret;
> +
> +	sync_mode &= ~(GC2145_SYNC_MODE_VSYNC_POL |
> +		       GC2145_SYNC_MODE_HSYNC_POL |
> +		       GC2145_SYNC_MODE_OPCLK_POL);
> +
> +	if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
> +		sync_mode |= GC2145_SYNC_MODE_VSYNC_POL;
> +
> +	if (flags & V4L2_MBUS_HSYNC_ACTIVE_LOW)
> +		sync_mode |= GC2145_SYNC_MODE_HSYNC_POL;
> +
> +	if (flags & V4L2_MBUS_PCLK_SAMPLE_FALLING)
> +		sync_mode |= GC2145_SYNC_MODE_OPCLK_POL;
> +
> +	cci_write(gc2145->regmap, GC2145_REG_SYNC_MODE, sync_mode, &ret);
> +	cci_write(gc2145->regmap, GC2145_REG_PAD_IO, 0x0f, &ret);
> +
> +	return ret;
> +}
> +
>  static const struct cci_reg_sequence gc2145_common_mipi_regs[] = {
>  	{GC2145_REG_PAGE_SELECT, 0x03},
>  	{GC2145_REG_DPHY_ANALOG_MODE1, GC2145_DPHY_MODE_PHY_CLK_EN |
> @@ -895,10 +943,13 @@ static int gc2145_start_streaming(struct gc2145 *gc2145,
>  		goto err_rpm_put;
>  	}
>  
> -	/* Perform MIPI specific configuration */
> -	ret = gc2145_config_mipi_mode(gc2145, gc2145_format);
> +	/* Perform interface specific configuration */
> +	if (gc2145_is_csi2(gc2145))
> +		ret = gc2145_config_mipi_mode(gc2145, gc2145_format);
> +	else
> +		ret = gc2145_config_dvp_mode(gc2145, gc2145_format);
>  	if (ret) {
> -		dev_err(&client->dev, "%s failed to write mipi conf\n",
> +		dev_err(&client->dev, "%s failed to write interface conf\n",
>  			__func__);
>  		goto err_rpm_put;
>  	}
> @@ -924,6 +975,9 @@ static void gc2145_stop_streaming(struct gc2145 *gc2145)
>  			GC2145_CSI2_MODE_EN | GC2145_CSI2_MODE_MIPI_EN, 0,
>  			&ret);
>  	cci_write(gc2145->regmap, GC2145_REG_PAGE_SELECT, 0x00, &ret);
> +
> +	/* Disable dvp streaming */
> +	cci_write(gc2145->regmap, GC2145_REG_PAD_IO, 0x00, &ret);
>  	if (ret)
>  		dev_err(&client->dev, "%s failed to write regs\n", __func__);
>  
> @@ -1233,9 +1287,8 @@ static int gc2145_init_controls(struct gc2145 *gc2145)
>  static int gc2145_check_hwcfg(struct device *dev)
>  {
>  	struct fwnode_handle *endpoint;
> -	struct v4l2_fwnode_endpoint ep_cfg = {
> -		.bus_type = V4L2_MBUS_CSI2_DPHY
> -	};

First try D-PHY and if that fails, then try PARALLEL.

> +	struct v4l2_subdev *sd = dev_get_drvdata(dev);
> +	struct gc2145 *gc2145 = to_gc2145(sd);
>  	int ret;
>  
>  	endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL);
> @@ -1244,36 +1297,46 @@ static int gc2145_check_hwcfg(struct device *dev)
>  		return -EINVAL;
>  	}
>  
> -	ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &ep_cfg);
> +	ret = v4l2_fwnode_endpoint_parse(endpoint, &gc2145->ep);

You won't have any link frequencies available with this change.

>  	fwnode_handle_put(endpoint);
>  	if (ret)
>  		return ret;
>  
> -	/* Check the number of MIPI CSI2 data lanes */
> -	if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) {
> -		dev_err(dev, "only 2 data lanes are currently supported\n");
> -		ret = -EINVAL;
> -		goto out;
> -	}
> +	switch (gc2145->ep.bus_type) {
> +	case V4L2_MBUS_CSI2_DPHY:
> +		/* Check the link frequency set in device tree */
> +		if (!gc2145->ep.nr_of_link_frequencies) {
> +			dev_err(dev, "link-frequencies property not found in DT\n");
> +			ret = -EINVAL;
> +			goto out;
> +		}
> +
> +		/* Check the number of MIPI CSI2 data lanes */
> +		if (gc2145->ep.bus.mipi_csi2.num_data_lanes != 2) {
> +			dev_err(dev, "only 2 data lanes are currently supported\n");
> +			ret = -EINVAL;
> +			goto out;
> +		}
> +
> +		if (gc2145->ep.nr_of_link_frequencies != 3 ||
> +			gc2145->ep.link_frequencies[0] != GC2145_640_480_LINKFREQ ||
> +			gc2145->ep.link_frequencies[1] != GC2145_1280_720_LINKFREQ ||
> +			gc2145->ep.link_frequencies[2] != GC2145_1600_1200_LINKFREQ) {
> +			dev_err(dev, "Invalid link-frequencies provided\n");
> +			ret = -EINVAL;
> +			goto out;
> +		}
> +		break;
>  
> -	/* Check the link frequency set in device tree */
> -	if (!ep_cfg.nr_of_link_frequencies) {
> -		dev_err(dev, "link-frequency property not found in DT\n");
> +	case V4L2_MBUS_PARALLEL:
> +		break;
> +	default:
> +		dev_err(dev, "unsupported bus type %u\n",
> +			gc2145->ep.bus_type);

Fits on the previous line.

>  		ret = -EINVAL;
>  		goto out;
>  	}
> -
> -	if (ep_cfg.nr_of_link_frequencies != 3 ||
> -	    ep_cfg.link_frequencies[0] != GC2145_640_480_LINKFREQ ||
> -	    ep_cfg.link_frequencies[1] != GC2145_1280_720_LINKFREQ ||
> -	    ep_cfg.link_frequencies[2] != GC2145_1600_1200_LINKFREQ) {
> -		dev_err(dev, "Invalid link-frequencies provided\n");
> -		ret = -EINVAL;
> -	}
> -
>  out:
> -	v4l2_fwnode_endpoint_free(&ep_cfg);
> -
>  	return ret;
>  }
>  

-- 
Regards,

Sakari Ailus