[PATCH v1 00/49] ARM: dts: imx: Use #pwm-cells = <3> for imx27-pwm device

[PATCH v1 00/49] ARM: dts: imx: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

Hello,

this series addresses many warnings of the type:

	arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
	        from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

that is emitted when building with CHECK_DTBS=1.

This completes the conversion started with

	fa28d8212ede ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
	4c6f19ab2aed ("dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles")

Best regards
Uwe

Uwe Kleine-König (49):
  ARM: dts: imx51-ts4800: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx53-m53evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx53-ppd: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx53-kp: Drop redundant settings in pwm nodes
  ARM: dts: imx53-tqma: Use #pwm-cells = <3> for imx27-pwm devices
  ARM: dts: imx6dl-aristainetos_4: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6dl-aristainetos_7: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6dl-mamoj: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-ba16: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-bosch-acc: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-apf6dev: Use #pwm-cells = <3> for imx27-pwm devices
  ARM: dts: imx6qdl-aristainetos2: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-cubox-i: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-emcon: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-gw52xx: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-gw53xx: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-gw54xx: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-gw560x: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-gw5903: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-gw5904: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-icore: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-nit6xlite: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-nitrogen6_max: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-nitrogen6_som2: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-nitrogen6x: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-phytec-mira: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-sabreauto: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-sabrelite: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-sabresd: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-savageboard: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-skov-cpu: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-kp: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-novena: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-pistachio: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-prti6q: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-var-dt6customboard: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sl-evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sll-evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sx-nitrogen6sx: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sx-sdb: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sx-softing-vining-2000: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-14x14-evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-ccimx6ulsbcpro: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-geam: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-imx6ull-opos6uldev: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-isiot: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-kontron-bl-43: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-kontron-bl-common: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-pico: Use #pwm-cells = <3> for imx27-pwm device

 arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts           |  3 +--
 arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts           |  2 +-
 arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi              | 10 +---------
 arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts           |  3 +--
 arch/arm/boot/dts/nxp/imx/imx53-mba53.dts            |  2 +-
 arch/arm/boot/dts/nxp/imx/imx53-ppd.dts              |  6 ++----
 arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi          |  8 --------
 arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts  |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts  |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts           |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi            |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts        | 10 +++-------
 arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi              |  6 ++----
 arch/arm/boot/dts/nxp/imx/imx6q-novena.dts           |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts           |  3 +--
 .../boot/dts/nxp/imx/imx6q-var-dt6customboard.dts    |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi       |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi       |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi         |  9 +++------
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi        |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi         |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi     |  6 ++----
 arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi |  9 +++------
 .../arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi |  6 ++----
 arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi    |  6 ++----
 arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi   |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi     |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi     |  9 +++------
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi       |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi   |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi      |  1 -
 arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts             |  4 +---
 arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts            |  4 +---
 arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts     |  4 +---
 arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi            |  4 +---
 .../boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts  | 12 +++---------
 arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi      |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts  |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts            |  3 +--
 .../boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi  |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi          |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts   |  3 +--
 .../boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi   |  3 +--
 arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi           |  3 +--
 51 files changed, 64 insertions(+), 150 deletions(-)


base-commit: 4cece764965020c22cff7665b18a012006359095
-- 
2.43.0

[PATCH v1 01/49] ARM: dts: imx51-ts4800: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx51-ts4800.dtb: pwm@73fb4000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts b/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
index f7408722d68a..2bd0761c7e90 100644
--- a/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
@@ -45,7 +45,7 @@ backlight_reg: regulator-backlight {
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 78770>;
+		pwms = <&pwm1 0 78770 0>;
 		brightness-levels = <0 150 200 255>;
 		default-brightness-level = <1>;
 		power-supply = <&backlight_reg>;
@@ -113,7 +113,6 @@ &ipu_di0_disp1 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm_backlight>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 02/49] ARM: dts: imx53-m53evk: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx53-m53evk.dtb: pwm@53fb4000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts b/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
index c323b4dbe9f0..1353d985969c 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
@@ -41,7 +41,7 @@ display1_in: endpoint {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 3000>;
+		pwms = <&pwm1 0 3000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		power-supply = <&reg_backlight>;
@@ -313,7 +313,6 @@ &ipu_di1_disp1 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 03/49] ARM: dts: imx53-ppd: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx53-ppd.dtb: pwm@53fb4000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx53-ppd.dtb: pwm@53fb8000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx53-ppd.dts | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts b/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
index 70c4a4852256..e939acc1c88b 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
@@ -167,7 +167,7 @@ reg_3v3_lcd: regulator-3v3-lcd {
 
 	pwm_bl: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35
 				     38 40 43 45 48 51 53 56 58 61 63 66 68 71
 				     73 76 79 81 84 86 89 91 94 96 99 102 104
@@ -187,7 +187,7 @@ led-controller-1 {
 
 		led-1 {
 			label = "alarm-brightness";
-			pwms = <&pwm1 0 100000>;
+			pwms = <&pwm1 0 100000 0>;
 			max-brightness = <255>;
 		};
 	};
@@ -628,14 +628,12 @@ &pmu {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 04/49] ARM: dts: imx53-kp: Drop redundant settings in pwm nodes

[Uwe Kleine-König]

imx53-kp.dtsi includes imx53-tqma53.dtsi which already sets #pwm-cells
to 2. So the two nodes can be dropped without resulting in any changes
in the compiled device tree blobs.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi | 8 --------
 1 file changed, 8 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
index 4508f34139a0..8b25416a5303 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
@@ -162,14 +162,6 @@ MX53_PAD_EIM_D20__GPIO3_20 0x1e4
 	>;
 };
 
-&pwm1 {
-	#pwm-cells = <2>;
-};
-
-&pwm2 {
-	#pwm-cells = <2>;
-};
-
 &uart1 {
 	status = "okay";
 };
-- 
2.43.0

[PATCH v1 05/49] ARM: dts: imx53-tqma: Use #pwm-cells = <3> for imx27-pwm devices

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dtb: pwm@53fb4000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dtb: pwm@53fb8000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dtb: pwm@53fb4000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dtb: pwm@53fb8000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx53-mba53.dtb: pwm@53fb4000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx53-mba53.dtb: pwm@53fb8000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts  | 2 +-
 arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi     | 2 +-
 arch/arm/boot/dts/nxp/imx/imx53-mba53.dts   | 2 +-
 arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi | 8 --------
 4 files changed, 3 insertions(+), 11 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts b/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
index 0e7f071fd10e..f6f116366643 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
@@ -13,7 +13,7 @@ / {
 
 	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		power-supply = <&reg_backlight>;
 		brightness-levels = <0 24 28 32 36
 				     40 44 48 52 56
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
index 8b25416a5303..ae5f87b8612d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
@@ -13,7 +13,7 @@ buzzer {
 		compatible = "pwm-beeper";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_buzzer>;
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 	};
 
 	gpio-buttons {
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
index 6a37616cef1c..2117de872703 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
@@ -17,7 +17,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>;
 		default-brightness-level = <10>;
 		enable-gpios = <&gpio7 7 0>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
index 294811bfc8d2..b2d7271d1d24 100644
--- a/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
@@ -202,14 +202,6 @@ MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
 	};
 };
 
-&pwm1 {
-	#pwm-cells = <2>;
-};
-
-&pwm2 {
-	#pwm-cells = <2>;
-};
-
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-- 
2.43.0

[PATCH v1 06/49] ARM: dts: imx6dl-aristainetos_4: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
index cc861a43eb58..a5ac79346854 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
@@ -14,7 +14,7 @@ / {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		enable-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
@@ -79,6 +79,5 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
-- 
2.43.0

[PATCH v1 07/49] ARM: dts: imx6dl-aristainetos_7: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
index b6cb78870cd5..5a25bdbbeb68 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
@@ -49,7 +49,7 @@ display0_in: endpoint {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 3000>;
+		pwms = <&pwm3 0 3000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		pinctrl-names = "default";
@@ -69,6 +69,5 @@ &ipu1_di0_disp0 {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
-- 
2.43.0

[PATCH v1 08/49] ARM: dts: imx6dl-mamoj: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
index 028951955bde..72ee236d2f5e 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 25000>; /* 25000ns -> 40kHz */
+		pwms = <&pwm3 0 25000 0>; /* 25000ns -> 40kHz */
 		brightness-levels = <0 4 8 16 32 64 128 160 192 224 255>;
 		default-brightness-level = <7>;
 	};
@@ -303,7 +303,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 09/49] ARM: dts: imx6q-ba16: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6q-b450v3.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-b650v3.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-b850v3.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-dms-ba16.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
index f266f1b7e0cf..09d9ca0cb332 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
@@ -55,7 +55,7 @@ backlight_lvds: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_display>;
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
 				      10  11  12  13  14  15  16  17  18  19
 				      20  21  22  23  24  25  26  27  28  29
@@ -349,7 +349,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 10/49] ARM: dts: imx6q-bosch-acc: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
index 02648806c275..d3f14b4d3b51 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
@@ -36,7 +36,7 @@ memory@10000000 {
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 200000>;
+		pwms = <&pwm1 0 200000 0>;
 		brightness-levels = <0 61 499 1706 4079 8022 13938 22237 33328 47623 65535>;
 		num-interpolated-steps = <10>;
 		default-brightness-level = <60>;
@@ -117,14 +117,14 @@ led_red: led-0 {
 			color = <LED_COLOR_ID_RED>;
 			max-brightness = <248>;
 			default-state = "off";
-			pwms = <&pwm2 0 500000>;
+			pwms = <&pwm2 0 500000 0>;
 		};
 
 		led_white: led-1 {
 			color = <LED_COLOR_ID_WHITE>;
 			max-brightness = <248>;
 			default-state = "off";
-			pwms = <&pwm3 0 500000>;
+			pwms = <&pwm3 0 500000 0>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -484,28 +484,24 @@ lvds0_out: endpoint {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 11/49] ARM: dts: imx6qdl-apf6dev: Use #pwm-cells = <3> for imx27-pwm devices

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-apf6dev.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-apf6dev.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
index 338d292553ad..3a46ade3b6bd 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
@@ -13,7 +13,7 @@ chosen {
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 191000>;
+		pwms = <&pwm3 0 191000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <0>;
 		power-supply = <&reg_5v>;
@@ -212,7 +212,6 @@ &pcie {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 12/49] ARM: dts: imx6qdl-aristainetos2: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_4.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_7.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
index db1bc511e71f..758eaf9d93d2 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
@@ -46,7 +46,7 @@
 / {
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		enable-gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
@@ -346,7 +346,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 13/49] ARM: dts: imx6qdl-cubox-i: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-emmc-som-v15.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-som-v15.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-cubox-i.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-emmc-som-v15.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-som-v15.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
index 1e530d892b76..761566ae3cf5 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
@@ -64,7 +64,7 @@ led-1 {
 			active-low;
 			label = "imx6:red:front";
 			max-brightness = <248>;
-			pwms = <&pwm1 0 50000>;
+			pwms = <&pwm1 0 50000 0>;
 		};
 	};
 
@@ -233,7 +233,6 @@ MX6QDL_PAD_EIM_DA8__GPIO3_IO08	0x17059
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
-- 
2.43.0

[PATCH v1 14/49] ARM: dts: imx6qdl-emcon: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
index 42b2ba23aefc..a308a3584b62 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
@@ -66,7 +66,7 @@ lvds_backlight: lvds-backlight {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lvds_bl>;
 		enable-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>;
-		pwms = <&pwm1 0 50000>;
+		pwms = <&pwm1 0 50000 0>;
 		brightness-levels = <
 			0 4 8 16 32 64 80 96 112
 			128 144 160 176 250
@@ -78,7 +78,7 @@ lvds_backlight: lvds-backlight {
 	pwm_fan: pwm-fan {
 		compatible = "pwm-fan";
 		#cooling-cells = <2>;
-		pwms = <&pwm4 0 50000>;
+		pwms = <&pwm4 0 50000 0>;
 		cooling-levels = <0 64 127 191 255>;
 		status = "disabled";
 	};
@@ -145,7 +145,7 @@ rgb_backlight: rgb-backlight {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rgb_bl>;
 		enable-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <
 			250 176 160 144 128 112
 			96 80 64 48 32 16 8 1
@@ -736,17 +736,14 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
-- 
2.43.0

[PATCH v1 15/49] ARM: dts: imx6qdl-gw52xx: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-gw52xx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-gw52xx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
index 535679c27d6f..48ffb3ee01bd 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
@@ -25,7 +25,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -520,7 +520,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 16/49] ARM: dts: imx6qdl-gw53xx: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-gw53xx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-gw53xx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
index 3e1c572af582..1eae438fbdae 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
@@ -25,7 +25,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -517,7 +517,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 17/49] ARM: dts: imx6qdl-gw54xx: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-gw54xx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-gw54xx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
index 0ffa0357a6fa..c2ec8572c8a5 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
@@ -26,7 +26,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -570,7 +570,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default", "state_dio";
 	pinctrl-0 = <&pinctrl_pwm4_backlight>;
 	pinctrl-1 = <&pinctrl_pwm4_dio>;
-- 
2.43.0

[PATCH v1 18/49] ARM: dts: imx6qdl-gw560x: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-gw560x.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
index 46cf4080fec3..7cee983da669 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
@@ -66,7 +66,7 @@ chosen {
 
 	backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <
 			0  1  2  3  4  5  6  7  8  9
 			10 11 12 13 14 15 16 17 18 19
@@ -619,7 +619,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 19/49] ARM: dts: imx6qdl-gw5903: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-gw5903.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-gw5903.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
index a74cde050158..fbc704c064b6 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
@@ -56,7 +56,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <
 			0  1  2  3  4  5  6  7  8  9
 			10 11 12 13 14 15 16 17 18 19
@@ -502,7 +502,6 @@ timing0: g101evn010 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 20/49] ARM: dts: imx6qdl-gw5904: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-gw5904.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-gw5904.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
index 1e723807ab4c..070506279186 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
@@ -70,7 +70,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -586,7 +586,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 21/49] ARM: dts: imx6qdl-icore: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-icore.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-icore-mipi.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-icore.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-icore-mipi.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap10.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap12.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
index efe11524b885..9975b6ee433d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
@@ -20,7 +20,7 @@ chosen {
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 100000>;
+		pwms = <&pwm3 0 100000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -245,7 +245,6 @@ mipi_csi2_in: endpoint {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 22/49] ARM: dts: imx6qdl-nit6xlite: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-nit6xlite.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-nit6xlite.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
index f2542d725ce7..a30cf0d06206 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
@@ -108,7 +108,7 @@ led-j46-pin3 {
 
 	backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -117,7 +117,7 @@ backlight-lcd {
 
 	backlight_lvds0: backlight-lvds0 {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -499,7 +499,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -512,7 +511,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 23/49] ARM: dts: imx6qdl-nitrogen6_max: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
index 32a110a35b02..33174febf410 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
@@ -183,7 +183,7 @@ led-ttymxc4-rs232 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -192,7 +192,7 @@ backlight_lcd: backlight-lcd {
 
 	backlight_lvds0: backlight-lvds0 {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -201,7 +201,7 @@ backlight_lvds0: backlight-lvds0 {
 
 	backlight_lvds1: backlight-lvds1 {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 5000000>;
+		pwms = <&pwm2 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -735,14 +735,12 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
@@ -755,7 +753,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 24/49] ARM: dts: imx6qdl-nitrogen6_som2: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_som2.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_som2.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_som2.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_som2.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
index 414196b75991..8e64314fa8b2 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
@@ -17,7 +17,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -26,7 +26,7 @@ backlight_lcd: backlight-lcd {
 
 	backlight_lvds0: backlight-lvds0 {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -641,7 +641,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -654,7 +653,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 25/49] ARM: dts: imx6qdl-nitrogen6x: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-nitrogen6x.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-nitrogen6x.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6x.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6x.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
index f278b14911ce..121177273dd0 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
@@ -134,7 +134,7 @@ sound {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -143,7 +143,7 @@ backlight_lcd: backlight-lcd {
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -596,7 +596,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -609,7 +608,6 @@ &pwm3 {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 26/49] ARM: dts: imx6qdl-phytec-mira: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-phytec-mira-rdk-nand.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-emmc.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-nand.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-phytec-mira-rdk-nand.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
index 1ca4d219609f..0b4c09b09c03 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
@@ -15,7 +15,7 @@ backlight: backlight {
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_backlight>;
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		status = "okay";
 	};
 
@@ -224,7 +224,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 27/49] ARM: dts: imx6qdl-sabreauto: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-sabreauto.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
index 68e97180d33e..69b9d7a4bcef 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
@@ -153,7 +153,7 @@ sound-spdif {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		status = "okay";
@@ -802,7 +802,6 @@ timing0: hsd100pxn1 {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 28/49] ARM: dts: imx6qdl-sabrelite: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
index 84c8a9531e18..9c502bf77d0b 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
@@ -99,7 +99,7 @@ mipi_xclk: mipi_xclk {
 		#clock-cells = <0>;
 		clock-frequency = <22000000>;
 		clock-output-names = "mipi_pwm3";
-		pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
+		pwms = <&pwm3 0 45 0>; /* 1 / 45 ns = 22 MHz */
 		status = "okay";
 	};
 
@@ -162,7 +162,7 @@ sound {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -171,7 +171,7 @@ backlight_lcd: backlight-lcd {
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -654,21 +654,18 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 29/49] ARM: dts: imx6qdl-sabresd: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-sabresd.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-sabresd.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6qp-sabresd.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
index 4fe58764b929..8f4f5fba68cc 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
@@ -119,7 +119,7 @@ sound {
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		status = "okay";
@@ -755,7 +755,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 30/49] ARM: dts: imx6qdl-savageboard: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-savageboard.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-savageboard.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
index 02e6d36e85fa..6823a639ed2f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
@@ -83,7 +83,7 @@ panel_bl: backlight {
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <4>;
 		power-supply = <&reg_3p3v>;
-		pwms = <&pwm1 0 10000>;
+		pwms = <&pwm1 0 10000 0>;
 	};
 
 	reg_3p3v: regulator-3p3v {
@@ -140,7 +140,6 @@ lvds0_out: endpoint {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 31/49] ARM: dts: imx6qdl-skov-cpu: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt6.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt2.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt6.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-skov-reve-mi1010ait-1cp1.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
index d59d5d0e1d19..6ab71a729fd8 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
@@ -282,7 +282,6 @@ i2c_rtc: rtc@51 {
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
-- 
2.43.0

[PATCH v1 32/49] ARM: dts: imx6q-kp: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6q-kp-tpc.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6q-kp-tpc.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
index 091903f53a56..c425d427663d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
@@ -15,7 +15,7 @@
 / {
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 255>;
 		num-interpolated-steps = <255>;
 		default-brightness-level = <250>;
@@ -23,7 +23,7 @@ backlight_lcd: backlight-lcd {
 
 	beeper {
 		compatible = "pwm-beeper";
-		pwms = <&pwm2 0 500000>;
+		pwms = <&pwm2 0 500000 0>;
 	};
 
 	lcd_display: display {
@@ -378,14 +378,12 @@ MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 33/49] ARM: dts: imx6q-novena: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6q-novena.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-novena.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts b/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
index a7d5a68110fc..d392b5bd2eea 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
@@ -67,7 +67,7 @@ chosen {
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 10000000>;
+		pwms = <&pwm1 0 10000000 0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight_novena>;
 		power-supply = <&reg_lvds_lcd>;
@@ -465,7 +465,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
-- 
2.43.0

[PATCH v1 34/49] ARM: dts: imx6q-pistachio: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
index 46c6b96d8073..56b77cc0af2b 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
@@ -124,7 +124,7 @@ sound {
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
+		pwms = <&pwm1 0 50000 0>;
 		brightness-levels = <
 			0  /*1  2  3  4  5  6*/  7  8  9
 			10 11 12 13 14 15 16 17 18 19
@@ -571,7 +571,6 @@ lvds0_out: endpoint {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 35/49] ARM: dts: imx6q-prti6q: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts b/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
index 3508a2cd928a..a7d5693c5ab7 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
@@ -22,7 +22,7 @@ backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
 		default-brightness-level = <1>;
@@ -292,7 +292,6 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 36/49] ARM: dts: imx6q-var-dt6customboard: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
index 2290c1237634..0225a621ec7a 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
@@ -18,7 +18,7 @@ / {
 
 	backlight_lvds: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 248>;
 		default-brightness-level = <7>;
 		status = "okay";
@@ -203,7 +203,6 @@ lvds1_out: endpoint {
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
-- 
2.43.0

[PATCH v1 37/49] ARM: dts: imx6sl-evk: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6sl-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable these devices. Drop this property, too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
index 239bc6dfc584..31eee0419af7 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
@@ -23,7 +23,7 @@ memory@80000000 {
 
 	backlight_display: backlight_display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
@@ -584,10 +584,8 @@ display_out: endpoint {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
 };
 
 &reg_vdd1p1 {
-- 
2.43.0

[PATCH v1 38/49] ARM: dts: imx6sll-evk: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6sll-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable this device. Drop this property, too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
index e3e9b0ec4f73..febc2dd9967d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
@@ -26,7 +26,7 @@ memory@80000000 {
 
 	backlight_display: backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -314,10 +314,8 @@ display_out: endpoint {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
 };
 
 &snvs_poweroff {
-- 
2.43.0

[PATCH v1 39/49] ARM: dts: imx6sx-nitrogen6sx: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable this device. Drop this property, too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
index cd9cbc9ccc9e..8adc2b362ab2 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
@@ -18,7 +18,7 @@ memory@80000000 {
 
 	backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		power-supply = <&reg_3p3v>;
@@ -229,10 +229,8 @@ &pcie {
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
-	status = "okay";
 };
 
 &ssi1 {
-- 
2.43.0

[PATCH v1 40/49] ARM: dts: imx6sx-sdb: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6sx-sdb-reva.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6sx-sdb-sai.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable this device. Drop this property, too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
index c6e85e4a0883..0c6ed5f988c2 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
@@ -23,7 +23,7 @@ memory@80000000 {
 
 	backlight_display: backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
@@ -295,10 +295,8 @@ display_out: endpoint {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
 };
 
 &snvs_poweroff {
-- 
2.43.0

[PATCH v1 41/49] ARM: dts: imx6sx-softing-vining-2000: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dtb: pwm@22a8000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

There is no need for an explicit status = "okay" in the pwm nodes as
the soc dtsi doesn't disable these devices. Drop these properties, too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 .../boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts  | 12 +++---------
 1 file changed, 3 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
index bfcd8f7d86dd..f999eb244373 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
@@ -46,19 +46,19 @@ led-controller {
 		led-1 {
 			label = "red";
 			max-brightness = <255>;
-			pwms = <&pwm6 0 50000>;
+			pwms = <&pwm6 0 50000 0>;
 		};
 
 		led-2 {
 			label = "green";
 			max-brightness = <255>;
-			pwms = <&pwm2 0 50000>;
+			pwms = <&pwm2 0 50000 0>;
 		};
 
 		led-3 {
 			label = "blue";
 			max-brightness = <255>;
-			pwms = <&pwm1 0 50000>;
+			pwms = <&pwm1 0 50000 0>;
 		};
 	};
 };
@@ -505,24 +505,18 @@ &pcie {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
-	status = "okay";
 };
 
 &pwm6 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm6>;
-	status = "okay";
 };
 
 &reg_arm {
-- 
2.43.0

[PATCH v1 42/49] ARM: dts: imx6ul-14x14-evk: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ull-14x14-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ulz-14x14-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
index f10f0525490b..9cfb99ac9e9d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
@@ -16,7 +16,7 @@ memory@80000000 {
 
 	backlight_display: backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -277,7 +277,6 @@ display_out: endpoint {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 43/49] ARM: dts: imx6ul-ccimx6ulsbcpro: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dtb: pwm@20f0000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
index 1762bc47e18d..ed61ae8524fa 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
@@ -18,7 +18,7 @@ / {
 
 	lcd_backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm5 0 50000>;
+		pwms = <&pwm5 0 50000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -168,7 +168,6 @@ &pwm4 {
 };
 
 &pwm5 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm5>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 44/49] ARM: dts: imx6ul-geam: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6ul-geam.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
index 2ca18f3dad0a..cdbb8c435cd6 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
@@ -21,7 +21,7 @@ memory@80000000 {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm8 0 100000>;
+		pwms = <&pwm8 0 100000 0>;
 		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
 				     10 11 12 13 14 15 16 17 18 19
 				     20 21 22 23 24 25 26 27 28 29
@@ -194,7 +194,6 @@ timing0: timing0 {
 };
 
 &pwm8 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 45/49] ARM: dts: imx6ul-imx6ull-opos6uldev: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6ul-opos6uldev.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ull-opos6uldev.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
index af337f18a266..be3cacb4fa7a 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
@@ -9,7 +9,7 @@ chosen {
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 191000>;
+		pwms = <&pwm3 0 191000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_5v>;
@@ -143,7 +143,6 @@ lcdif_out: endpoint {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 46/49] ARM: dts: imx6ul-isiot: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6ul-isiot-emmc.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
index 14fc4828ba4e..ee86c36205f9 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
@@ -20,7 +20,7 @@ chosen {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm8 0 100000>;
+		pwms = <&pwm8 0 100000 0>;
 		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
 				     10 11 12 13 14 15 16 17 18 19
 				     20 21 22 23 24 25 26 27 28 29
@@ -187,7 +187,6 @@ timing0: timing0 {
 };
 
 &pwm8 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 47/49] ARM: dts: imx6ul-kontron-bl-43: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warning:

	arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dtb: pwm@20f8000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
index 0c643706a158..4e8191a65211 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
@@ -14,7 +14,7 @@ / {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm7 0 5000000>;
+		pwms = <&pwm7 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -41,7 +41,6 @@ &lcdif {
 };
 
 &pwm7 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm7>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 48/49] ARM: dts: imx6ul-kontron-bl-common: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
index 33d5f27285a4..d8f7877349c9 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
@@ -35,7 +35,7 @@ led3 {
 
 	pwm-beeper {
 		compatible = "pwm-beeper";
-		pwms = <&pwm8 0 5000>;
+		pwms = <&pwm8 0 5000 0>;
 	};
 
 	reg_3v3: regulator-3v3 {
@@ -152,7 +152,6 @@ rtc@32 {
 };
 
 &pwm8 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
-- 
2.43.0

[PATCH v1 49/49] ARM: dts: imx6ul-pico: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

The binding dictates using 3 pwm-cells. Adhere to that.

This fixes the following dtbs_check warnings:

	arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ul-pico-hobbit.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
	arch/arm/boot/dts/nxp/imx/imx6ul-pico-pi.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
		from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
index 07dcecbe485d..fe307f49b9e5 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
@@ -22,7 +22,7 @@ chosen {
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -177,7 +177,6 @@ display_out: endpoint {
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
-- 
2.43.0

Re: [PATCH v1 00/49] ARM: dts: imx: Use #pwm-cells = <3> for imx27-pwm device

[Uwe Kleine-König]

[-- Attachment #1: Type: text/plain, Size: 829 bytes --]

Hello,

On Fri, Apr 05, 2024 at 11:41:47PM +0200, Uwe Kleine-König wrote:
> this series addresses many warnings of the type:
> 
> 	arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
> 	        from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
> 
> that is emitted when building with CHECK_DTBS=1.
> 
> This completes the conversion started with
> 
> 	fa28d8212ede ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
> 	4c6f19ab2aed ("dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles")

Gentle ping! I would expect that Shawn picks up this series.

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v1 00/49] ARM: dts: imx: Use #pwm-cells = <3> for imx27-pwm device

[Shawn Guo]

On Fri, Apr 26, 2024 at 09:40:24PM +0200, Uwe Kleine-König wrote:
> Hello,
> 
> On Fri, Apr 05, 2024 at 11:41:47PM +0200, Uwe Kleine-König wrote:
> > this series addresses many warnings of the type:
> > 
> > 	arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
> > 	        from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
> > 
> > that is emitted when building with CHECK_DTBS=1.
> > 
> > This completes the conversion started with
> > 
> > 	fa28d8212ede ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
> > 	4c6f19ab2aed ("dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles")
> 
> Gentle ping! I would expect that Shawn picks up this series.

Thanks for reminding!  Applied all, thanks!

Shawn