[PATCH 0/3] arm64: dts: qcom: x1e80100: Describe 3 USB Type-C connectors currently used

[PATCH 0/3] arm64: dts: qcom: x1e80100: Describe 3 USB Type-C connectors currently used

[Abel Vesa]

Both QCP and CRD boards using X Elite (x1e80100) make use of 3 USB
Type-C ports (USB1 SS0, SS1, and SS2). Describe the graph for the USB
part of each one of them for now. The DP port will come at a later stage
since there are some muxes/retimers involved, depending on the type of
board.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
Abel Vesa (3):
      arm64: dts: qcom: x1e80100: Add ports nodes to USB1 SS[0-2] PHYs and controllers
      arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors
      arm64: dts: qcom: x1e80100-qcp: Add pmic-glink node with all 3 connectors

 arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 143 ++++++++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/x1e80100.dtsi    | 123 +++++++++++++++++++++++--
 3 files changed, 403 insertions(+), 6 deletions(-)
---
base-commit: 3689b0ef08b70e4e03b82ebd37730a03a672853a
change-id: 20231214-x1e80100-dts-pmic-glink-65e351579b8b

Best regards,
-- 
Abel Vesa <abel.vesa@linaro.org>

[PATCH 1/3] arm64: dts: qcom: x1e80100: Add ports nodes to USB1 SS[0-2] PHYs and controllers

[Abel Vesa]

All PHYs, being QMP combo type, implement both USB and DP. Add the port
nodes for high-speed, super-speed and DP to all 3 PHYs belonging to
USB1. Also add the counterpart nodes for the DWC3 controllers.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 123 +++++++++++++++++++++++++++++++--
 1 file changed, 117 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 5f90a0b3c016..63e85c5ea6c9 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -2543,6 +2543,29 @@ usb_1_ss0_qmpphy: phy@fd5000 {
 			#phy-cells = <1>;
 
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_1_ss0_qmpphy_out: endpoint {};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_1_ss0_qmpphy_usb_ss_in: endpoint {};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_1_ss0_qmpphy_dp_in: endpoint {};
+				};
+			};
 		};
 
 		usb_1_ss1_hsphy: phy@fd9000 {
@@ -2583,6 +2606,29 @@ usb_1_ss1_qmpphy: phy@fda000 {
 			#phy-cells = <1>;
 
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_1_ss1_qmpphy_out: endpoint {};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_1_ss1_qmpphy_usb_ss_in: endpoint {};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_1_ss1_qmpphy_dp_in: endpoint {};
+				};
+			};
 		};
 
 		usb_1_ss2_hsphy: phy@fde000 {
@@ -2623,6 +2669,29 @@ usb_1_ss2_qmpphy: phy@fdf000 {
 			#phy-cells = <1>;
 
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_1_ss2_qmpphy_out: endpoint {};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_1_ss2_qmpphy_usb_ss_in: endpoint {};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_1_ss2_qmpphy_dp_in: endpoint {};
+				};
+			};
 		};
 
 		cnoc_main: interconnect@1500000 {
@@ -3445,8 +3514,22 @@ usb_1_ss2_dwc3: usb@a000000 {
 
 				dma-coherent;
 
-				port {
-					usb_1_ss2_role_switch: endpoint {
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_ss2_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_ss2_dwc3_ss: endpoint {
+						};
 					};
 				};
 			};
@@ -3590,8 +3673,22 @@ usb_1_ss0_dwc3: usb@a600000 {
 
 				dma-coherent;
 
-				port {
-					usb_1_ss0_role_switch: endpoint {
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_ss0_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_ss0_dwc3_ss: endpoint {
+						};
 					};
 				};
 			};
@@ -3673,8 +3770,22 @@ usb_1_ss1_dwc3: usb@a800000 {
 
 				dma-coherent;
 
-				port {
-					usb_1_ss1_role_switch: endpoint {
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_ss1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_ss1_dwc3_ss: endpoint {
+						};
 					};
 				};
 			};

-- 
2.34.1

[PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Abel Vesa]

Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
for USB only, for now. The DP port will come at a later stage since it
uses a retimer.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
 1 file changed, 143 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index c5c2895b37c7..2fcc994cbb89 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -49,6 +49,101 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+					};
+				};
+			};
+		};
+
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+					};
+				};
+			};
+		};
+
+		connector@2 {
+			compatible = "usb-c-connector";
+			reg = <2>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss2_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss2_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss2_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss2_qmpphy_out>;
+					};
+				};
+			};
+		};
+	};
+
 	sound {
 		compatible = "qcom,x1e80100-sndcard";
 		model = "X1E80100-CRD";
@@ -852,6 +947,22 @@ &usb_1_ss0_dwc3 {
 	usb-role-switch;
 };
 
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_dwc3_ss {
+	remote-endpoint = <&usb_1_ss0_qmpphy_usb_ss_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss0_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_ss0_dwc3_ss>;
+};
+
 &usb_1_ss1_hsphy {
 	vdd-supply = <&vreg_l2e_0p8>;
 	vdda12-supply = <&vreg_l3e_1p2>;
@@ -874,6 +985,22 @@ &usb_1_ss1_dwc3 {
 	usb-role-switch;
 };
 
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_dwc3_ss {
+	remote-endpoint = <&usb_1_ss1_qmpphy_usb_ss_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss1_ss_in>;
+};
+
+&usb_1_ss1_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_ss1_dwc3_ss>;
+};
+
 &usb_1_ss2_hsphy {
 	vdd-supply = <&vreg_l2e_0p8>;
 	vdda12-supply = <&vreg_l3e_1p2>;
@@ -895,3 +1022,19 @@ &usb_1_ss2_dwc3 {
 	dr_mode = "host";
 	usb-role-switch;
 };
+
+&usb_1_ss2_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss2_hs_in>;
+};
+
+&usb_1_ss2_dwc3_ss {
+	remote-endpoint = <&usb_1_ss2_qmpphy_usb_ss_in>;
+};
+
+&usb_1_ss2_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss2_ss_in>;
+};
+
+&usb_1_ss2_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_ss2_dwc3_ss>;
+};

-- 
2.34.1

[PATCH 3/3] arm64: dts: qcom: x1e80100-qcp: Add pmic-glink node with all 3 connectors

[Abel Vesa]

Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
for USB only, for now. The DP port will come at a later stage since it
uses a mux.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 143 ++++++++++++++++++++++++++++++
 1 file changed, 143 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 2061fbe7b75a..a7eecf84b6d6 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -23,6 +23,101 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+					};
+				};
+			};
+		};
+
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+					};
+				};
+			};
+		};
+
+		connector@2 {
+			compatible = "usb-c-connector";
+			reg = <2>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss2_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss2_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss2_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss2_qmpphy_out>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 
@@ -548,6 +643,22 @@ &usb_1_ss0_dwc3 {
 	usb-role-switch;
 };
 
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_dwc3_ss {
+	remote-endpoint = <&usb_1_ss0_qmpphy_usb_ss_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss0_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_ss0_dwc3_ss>;
+};
+
 &usb_1_ss1_hsphy {
 	vdd-supply = <&vreg_l2e_0p8>;
 	vdda12-supply = <&vreg_l3e_1p2>;
@@ -570,6 +681,22 @@ &usb_1_ss1_dwc3 {
 	usb-role-switch;
 };
 
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_dwc3_ss {
+	remote-endpoint = <&usb_1_ss1_qmpphy_usb_ss_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss1_ss_in>;
+};
+
+&usb_1_ss1_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_ss1_dwc3_ss>;
+};
+
 &usb_1_ss2_hsphy {
 	vdd-supply = <&vreg_l2e_0p8>;
 	vdda12-supply = <&vreg_l3e_1p2>;
@@ -591,3 +718,19 @@ &usb_1_ss2_dwc3 {
 	dr_mode = "host";
 	usb-role-switch;
 };
+
+&usb_1_ss2_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss2_hs_in>;
+};
+
+&usb_1_ss2_dwc3_ss {
+	remote-endpoint = <&usb_1_ss2_qmpphy_usb_ss_in>;
+};
+
+&usb_1_ss2_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss2_ss_in>;
+};
+
+&usb_1_ss2_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_ss2_dwc3_ss>;
+};

-- 
2.34.1

Re: [PATCH 1/3] arm64: dts: qcom: x1e80100: Add ports nodes to USB1 SS[0-2] PHYs and controllers

[Dmitry Baryshkov]

On Mon, May 27, 2024 at 11:07:27AM +0300, Abel Vesa wrote:
> All PHYs, being QMP combo type, implement both USB and DP. Add the port
> nodes for high-speed, super-speed and DP to all 3 PHYs belonging to
> USB1. Also add the counterpart nodes for the DWC3 controllers.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 123 +++++++++++++++++++++++++++++++--
>  1 file changed, 117 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index 5f90a0b3c016..63e85c5ea6c9 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -2543,6 +2543,29 @@ usb_1_ss0_qmpphy: phy@fd5000 {
>  			#phy-cells = <1>;
>  
>  			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					usb_1_ss0_qmpphy_out: endpoint {};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					usb_1_ss0_qmpphy_usb_ss_in: endpoint {};
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usb_1_ss0_qmpphy_dp_in: endpoint {};

Unless the configuration is dynamic or platform-dependent, please link DWC3, QMP PHY and DP nodes in the SoC.dtsi.

> +				};
> +			};
>  		};
>  
>  		usb_1_ss1_hsphy: phy@fd9000 {
> @@ -2583,6 +2606,29 @@ usb_1_ss1_qmpphy: phy@fda000 {
>  			#phy-cells = <1>;
>  
>  			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					usb_1_ss1_qmpphy_out: endpoint {};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					usb_1_ss1_qmpphy_usb_ss_in: endpoint {};
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usb_1_ss1_qmpphy_dp_in: endpoint {};
> +				};
> +			};
>  		};
>  
>  		usb_1_ss2_hsphy: phy@fde000 {
> @@ -2623,6 +2669,29 @@ usb_1_ss2_qmpphy: phy@fdf000 {
>  			#phy-cells = <1>;
>  
>  			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					usb_1_ss2_qmpphy_out: endpoint {};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					usb_1_ss2_qmpphy_usb_ss_in: endpoint {};
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usb_1_ss2_qmpphy_dp_in: endpoint {};
> +				};
> +			};
>  		};
>  
>  		cnoc_main: interconnect@1500000 {
> @@ -3445,8 +3514,22 @@ usb_1_ss2_dwc3: usb@a000000 {
>  
>  				dma-coherent;
>  
> -				port {
> -					usb_1_ss2_role_switch: endpoint {
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +
> +						usb_1_ss2_dwc3_hs: endpoint {
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +
> +						usb_1_ss2_dwc3_ss: endpoint {
> +						};
>  					};
>  				};
>  			};
> @@ -3590,8 +3673,22 @@ usb_1_ss0_dwc3: usb@a600000 {
>  
>  				dma-coherent;
>  
> -				port {
> -					usb_1_ss0_role_switch: endpoint {
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +
> +						usb_1_ss0_dwc3_hs: endpoint {
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +
> +						usb_1_ss0_dwc3_ss: endpoint {
> +						};
>  					};
>  				};
>  			};
> @@ -3673,8 +3770,22 @@ usb_1_ss1_dwc3: usb@a800000 {
>  
>  				dma-coherent;
>  
> -				port {
> -					usb_1_ss1_role_switch: endpoint {
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +
> +						usb_1_ss1_dwc3_hs: endpoint {
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +
> +						usb_1_ss1_dwc3_ss: endpoint {
> +						};
>  					};
>  				};
>  			};
> 
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Dmitry Baryshkov]

On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:
> Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> for USB only, for now. The DP port will come at a later stage since it
> uses a retimer.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
>  1 file changed, 143 insertions(+)

Please rebase on top of https://lore.kernel.org/linux-arm-msm/20240429-usb-link-dtsi-v1-12-87c341b55cdf@linaro.org/, sorry about it.

> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> index c5c2895b37c7..2fcc994cbb89 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> @@ -49,6 +49,101 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	pmic-glink {
> +		compatible = "qcom,x1e80100-pmic-glink",
> +			     "qcom,sm8550-pmic-glink",
> +			     "qcom,pmic-glink";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
> +
> +		connector@0 {
> +			compatible = "usb-c-connector";
> +			reg = <0>;
> +			power-role = "dual";
> +			data-role = "dual";

Does this match the information reported by UCSI?

> +


-- 
With best wishes
Dmitry

Re: [PATCH 3/3] arm64: dts: qcom: x1e80100-qcp: Add pmic-glink node with all 3 connectors

[Dmitry Baryshkov]

On Mon, May 27, 2024 at 11:07:29AM +0300, Abel Vesa wrote:
> Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> for USB only, for now. The DP port will come at a later stage since it
> uses a mux.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 143 ++++++++++++++++++++++++++++++
>  1 file changed, 143 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
> index 2061fbe7b75a..a7eecf84b6d6 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
> @@ -23,6 +23,101 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	pmic-glink {
> +		compatible = "qcom,x1e80100-pmic-glink",
> +			     "qcom,sm8550-pmic-glink",
> +			     "qcom,pmic-glink";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
> +
> +		connector@0 {
> +			compatible = "usb-c-connector";
> +			reg = <0>;
> +			power-role = "dual";
> +			data-role = "dual";

Same question as for the previous patch.

> +

-- 
With best wishes
Dmitry

Re: [PATCH 1/3] arm64: dts: qcom: x1e80100: Add ports nodes to USB1 SS[0-2] PHYs and controllers

[Konrad Dybcio]

On 5/27/24 10:07, Abel Vesa wrote:
> All PHYs, being QMP combo type, implement both USB and DP. Add the port
> nodes for high-speed, super-speed and DP to all 3 PHYs belonging to
> USB1. Also add the counterpart nodes for the DWC3 controllers.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

You can substitute this with

https://lore.kernel.org/linux-arm-msm/20240512-typec-fix-sm8250-v4-8-ad153c747a97@linaro.org/

Konrad

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Konrad Dybcio]

On 5/27/24 10:07, Abel Vesa wrote:
> Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> for USB only, for now. The DP port will come at a later stage since it
> uses a retimer.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
>   1 file changed, 143 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> index c5c2895b37c7..2fcc994cbb89 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> @@ -49,6 +49,101 @@ chosen {
>   		stdout-path = "serial0:115200n8";
>   	};
>   
> +	pmic-glink {
> +		compatible = "qcom,x1e80100-pmic-glink",
> +			     "qcom,sm8550-pmic-glink",
> +			     "qcom,pmic-glink";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
> +
> +		connector@0 {

Could you describe them somehow? e.g.


/* Left rear port */
connector @0 {


There is probably some better terminology to describe the one closer and
farther away from the user, do as you will..

For the QCP, they're numbered on the chassis

Konrad

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Dmitry Baryshkov]

On Tue, May 28, 2024 at 02:28:08PM +0200, Konrad Dybcio wrote:
> 
> 
> On 5/27/24 10:07, Abel Vesa wrote:
> > Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> > for USB only, for now. The DP port will come at a later stage since it
> > uses a retimer.
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >   arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
> >   1 file changed, 143 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > index c5c2895b37c7..2fcc994cbb89 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > @@ -49,6 +49,101 @@ chosen {
> >   		stdout-path = "serial0:115200n8";
> >   	};
> > +	pmic-glink {
> > +		compatible = "qcom,x1e80100-pmic-glink",
> > +			     "qcom,sm8550-pmic-glink",
> > +			     "qcom,pmic-glink";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
> > +				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
> > +				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
> > +
> > +		connector@0 {
> 
> Could you describe them somehow? e.g.

Which reminds me that we should add OF bindings for physical_location
driver.

> 
> 
> /* Left rear port */
> connector @0 {
> 
> 
> There is probably some better terminology to describe the one closer and
> farther away from the user, do as you will..
> 
> For the QCP, they're numbered on the chassis
> 
> Konrad

-- 
With best wishes
Dmitry

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Johan Hovold]

On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:
> Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> for USB only, for now. The DP port will come at a later stage since it
> uses a retimer.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
>  1 file changed, 143 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> index c5c2895b37c7..2fcc994cbb89 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> @@ -49,6 +49,101 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	pmic-glink {
> +		compatible = "qcom,x1e80100-pmic-glink",
> +			     "qcom,sm8550-pmic-glink",
> +			     "qcom,pmic-glink";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
> +				    <&tlmm 125 GPIO_ACTIVE_HIGH>;

With this series applied, I'm getting the following error on boot of the
CRD:

	ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying

Known issue? Do you need to enable some quirk in the UCSI driver?

Johan

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Dmitry Baryshkov]

On Mon, 3 Jun 2024 at 11:48, Johan Hovold <johan@kernel.org> wrote:
>
> On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:
> > Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> > for USB only, for now. The DP port will come at a later stage since it
> > uses a retimer.
> >
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 143 ++++++++++++++++++++++++++++++
> >  1 file changed, 143 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > index c5c2895b37c7..2fcc994cbb89 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> > @@ -49,6 +49,101 @@ chosen {
> >               stdout-path = "serial0:115200n8";
> >       };
> >
> > +     pmic-glink {
> > +             compatible = "qcom,x1e80100-pmic-glink",
> > +                          "qcom,sm8550-pmic-glink",
> > +                          "qcom,pmic-glink";
> > +             #address-cells = <1>;
> > +             #size-cells = <0>;
> > +             orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
> > +                                 <&tlmm 123 GPIO_ACTIVE_HIGH>,
> > +                                 <&tlmm 125 GPIO_ACTIVE_HIGH>;
>
> With this series applied, I'm getting the following error on boot of the
> CRD:
>
>         ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying
>
> Known issue? Do you need to enable some quirk in the UCSI driver?

Not that I know. The message is caused by the UCSI not responding to
the PPM_RESET command. A trace from pmic-glink would be helpful.

-- 
With best wishes
Dmitry

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Johan Hovold]

On Mon, Jun 03, 2024 at 11:49:51AM +0300, Dmitry Baryshkov wrote:
> On Mon, 3 Jun 2024 at 11:48, Johan Hovold <johan@kernel.org> wrote:
> > On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:
> > > Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> > > for USB only, for now. The DP port will come at a later stage since it
> > > uses a retimer.

> > With this series applied, I'm getting the following error on boot of the
> > CRD:
> >
> >         ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying
> >
> > Known issue? Do you need to enable some quirk in the UCSI driver?
> 
> Not that I know. The message is caused by the UCSI not responding to
> the PPM_RESET command. A trace from pmic-glink would be helpful.

I don't have time to look into this right now, so only reporting to
Abel.

Looks like there are two more warnings earlier on boot which appear to
be related:

[   10.730571] ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: invalid connector number, ignoring
[   10.730656] pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: invalid connector number, ignoring

Johan

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Dmitry Baryshkov]

On Mon, Jun 03, 2024 at 11:26:28AM +0200, Johan Hovold wrote:
> On Mon, Jun 03, 2024 at 11:49:51AM +0300, Dmitry Baryshkov wrote:
> > On Mon, 3 Jun 2024 at 11:48, Johan Hovold <johan@kernel.org> wrote:
> > > On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:
> > > > Add the pmic-glink node and describe all 3 USB Type-C connectors. Do this
> > > > for USB only, for now. The DP port will come at a later stage since it
> > > > uses a retimer.
> 
> > > With this series applied, I'm getting the following error on boot of the
> > > CRD:
> > >
> > >         ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying
> > >
> > > Known issue? Do you need to enable some quirk in the UCSI driver?
> > 
> > Not that I know. The message is caused by the UCSI not responding to
> > the PPM_RESET command. A trace from pmic-glink would be helpful.
> 
> I don't have time to look into this right now, so only reporting to
> Abel.

Not having the hardware and not having the dumps I probalby can't help
either.

> Looks like there are two more warnings earlier on boot which appear to
> be related:
> 
> [   10.730571] ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: invalid connector number, ignoring
> [   10.730656] pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: invalid connector number, ignoring

It well might be.

-- 
With best wishes
Dmitry

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Johan Hovold]

On Mon, Jun 03, 2024 at 11:26:28AM +0200, Johan Hovold wrote:
> On Mon, Jun 03, 2024 at 11:49:51AM +0300, Dmitry Baryshkov wrote:
> > On Mon, 3 Jun 2024 at 11:48, Johan Hovold <johan@kernel.org> wrote:
> > > On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:

> I don't have time to look into this right now, so only reporting to
> Abel.
> 
> Looks like there are two more warnings earlier on boot which appear to
> be related:
> 
> [   10.730571] ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: invalid connector number, ignoring
> [   10.730656] pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: invalid connector number, ignoring

Ok, it's just the pmic ucsi driver that is hardcoding max two ports
still. I'll send a fix.

Johan

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Dmitry Baryshkov]

On Mon, 3 Jun 2024 at 12:49, Johan Hovold <johan@kernel.org> wrote:
>
> On Mon, Jun 03, 2024 at 11:26:28AM +0200, Johan Hovold wrote:
> > On Mon, Jun 03, 2024 at 11:49:51AM +0300, Dmitry Baryshkov wrote:
> > > On Mon, 3 Jun 2024 at 11:48, Johan Hovold <johan@kernel.org> wrote:
> > > > On Mon, May 27, 2024 at 11:07:28AM +0300, Abel Vesa wrote:
>
> > I don't have time to look into this right now, so only reporting to
> > Abel.
> >
> > Looks like there are two more warnings earlier on boot which appear to
> > be related:
> >
> > [   10.730571] ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: invalid connector number, ignoring
> > [   10.730656] pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: invalid connector number, ignoring
>
> Ok, it's just the pmic ucsi driver that is hardcoding max two ports
> still. I'll send a fix.

https://lore.kernel.org/linux-arm-msm/20240527-x1e80100-soc-qcom-pmic-glink-v1-1-e5c4cda2f745@linaro.org/

-- 
With best wishes
Dmitry

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Johan Hovold]

On Mon, Jun 03, 2024 at 11:49:04AM +0200, Johan Hovold wrote:
> On Mon, Jun 03, 2024 at 11:26:28AM +0200, Johan Hovold wrote:

> > [   10.730571] ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: invalid connector number, ignoring
> > [   10.730656] pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: invalid connector number, ignoring
> 
> Ok, it's just the pmic ucsi driver that is hardcoding max two ports
> still. I'll send a fix.

Abel had already sent a fix for the above here:

	https://lore.kernel.org/lkml/20240527-x1e80100-soc-qcom-pmic-glink-v1-1-e5c4cda2f745@linaro.org/

The PPMI init failure still remains, though:

	ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying

Johan

Re: [PATCH 2/3] arm64: dts: qcom: x1e80100-crd: Add pmic-glink node with all 3 connectors

[Johan Hovold]

On Mon, Jun 03, 2024 at 11:51:24AM +0200, Johan Hovold wrote:
> On Mon, Jun 03, 2024 at 11:49:04AM +0200, Johan Hovold wrote:
> > On Mon, Jun 03, 2024 at 11:26:28AM +0200, Johan Hovold wrote:
> 
> > > [   10.730571] ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: invalid connector number, ignoring
> > > [   10.730656] pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: invalid connector number, ignoring
> > 
> > Ok, it's just the pmic ucsi driver that is hardcoding max two ports
> > still. I'll send a fix.
> 
> Abel had already sent a fix for the above here:
> 
> 	https://lore.kernel.org/lkml/20240527-x1e80100-soc-qcom-pmic-glink-v1-1-e5c4cda2f745@linaro.org/

Nope, sorry, the above was for the PMIC GLINK driver itself. I just sent
a corresponding update for the GLINK UCSI driver here:

	https://lore.kernel.org/all/20240603100007.10236-1-johan+linaro@kernel.org/
 
> The PPMI init failure still remains, though:
> 
> 	ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying

Johan