[PATCH v2 1/7] arm64: dts: imx95: add edma[1..3] nodes

[PATCH v2 1/7] arm64: dts: imx95: add edma[1..3] nodes

[Frank Li]

Add eDMA1, eDMA2 and eDMA3 support for iMX95.
Add dmas and dma-names for each peripheral, which use eDMA.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change from v1 to v2
- none
---
 arch/arm64/boot/dts/freescale/imx95.dtsi | 235 +++++++++++++++++++++++
 1 file changed, 235 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
index 1bbf9a0468f69..12f7ac52c2589 100644
--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -3,6 +3,7 @@
  * Copyright 2024 NXP
  */
 
+#include <dt-bindings/dma/fsl-edma.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -405,6 +406,152 @@ aips2: bus@42000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			edma2: dma-controller@42000000 {
+				compatible = "fsl,imx95-edma5";
+				reg = <0x42000000 0x210000>;
+				#dma-cells = <3>;
+				dma-channels = <64>;
+				interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+				clock-names = "dma";
+			};
+
+			edma3: dma-controller@42210000 {
+				compatible = "fsl,imx95-edma5";
+				reg = <0x42210000 0x210000>;
+				#dma-cells = <3>;
+				dma-channels = <64>;
+				interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+				clock-names = "dma";
+			};
+
 			mu7: mailbox@42430000 {
 				compatible = "fsl,imx95-mu";
 				reg = <0x42430000 0x10000>;
@@ -464,6 +611,8 @@ lpi2c3: i2c@42530000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma2 8 0 0>, <&edma2 9 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -476,6 +625,8 @@ lpi2c4: i2c@42540000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma2 10 0 0>, <&edma2 11 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -488,6 +639,8 @@ lpspi3: spi@42550000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI3>,
 					 <&scmi_clk IMX95_CLK_BUSWAKEUP>;
 				clock-names = "per", "ipg";
+				dmas = <&edma2 12 0 0>, <&edma2 13 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -500,6 +653,8 @@ lpspi4: spi@42560000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI4>,
 					 <&scmi_clk IMX95_CLK_BUSWAKEUP>;
 				clock-names = "per", "ipg";
+				dmas = <&edma2 14 0 0>, <&edma2 15 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -510,6 +665,8 @@ lpuart3: serial@42570000 {
 				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART3>;
 				clock-names = "ipg";
+				dmas = <&edma2 18 0 FSL_EDMA_RX>, <&edma2 17 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -520,6 +677,8 @@ lpuart4: serial@42580000 {
 				interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART4>;
 				clock-names = "ipg";
+				dmas = <&edma2 20 0 FSL_EDMA_RX>, <&edma2 19 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -530,6 +689,8 @@ lpuart5: serial@42590000 {
 				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART5>;
 				clock-names = "ipg";
+				dmas = <&edma2 22 0 FSL_EDMA_RX>, <&edma2 21 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -540,6 +701,8 @@ lpuart6: serial@425a0000 {
 				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART6>;
 				clock-names = "ipg";
+				dmas = <&edma2 24 0 FSL_EDMA_RX>, <&edma2 23 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -550,6 +713,8 @@ lpuart7: serial@42690000 {
 				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART7>;
 				clock-names = "ipg";
+				dmas = <&edma2 26 0 FSL_EDMA_RX>, <&edma2 25 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -560,6 +725,8 @@ lpuart8: serial@426a0000 {
 				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART8>;
 				clock-names = "ipg";
+				dmas = <&edma2 28 0 FSL_EDMA_RX>, <&edma2 27 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -572,6 +739,8 @@ lpi2c5: i2c@426b0000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma2 71 0 0>, <&edma2 72 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -584,6 +753,8 @@ lpi2c6: i2c@426c0000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma2 73 0 0>, <&edma2 74 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -596,6 +767,8 @@ lpi2c7: i2c@426d0000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma2 75 0 0>, <&edma2 76 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -608,6 +781,8 @@ lpi2c8: i2c@426e0000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma2 77 0 0>, <&edma2 78 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -620,6 +795,8 @@ lpspi5: spi@426f0000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI5>,
 					 <&scmi_clk IMX95_CLK_BUSWAKEUP>;
 				clock-names = "per", "ipg";
+				dmas = <&edma2 79 0 0>, <&edma2 80 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -632,6 +809,8 @@ lpspi6: spi@42700000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI6>,
 					 <&scmi_clk IMX95_CLK_BUSWAKEUP>;
 				clock-names = "per", "ipg";
+				dmas = <&edma2 81 0 0>, <&edma2 82 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -644,6 +823,8 @@ lpspi7: spi@42710000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI7>,
 					 <&scmi_clk IMX95_CLK_BUSWAKEUP>;
 				clock-names = "per", "ipg";
+				dmas = <&edma2 83 0 0>, <&edma2 84 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -656,6 +837,8 @@ lpspi8: spi@42720000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI8>,
 					 <&scmi_clk IMX95_CLK_BUSWAKEUP>;
 				clock-names = "per", "ipg";
+				dmas = <&edma2 85 0 0>, <&edma2 86 0 FSL_EDMA_RX>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -796,6 +979,46 @@ aips1: bus@44000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			edma1: dma-controller@44000000 {
+				compatible = "fsl,imx93-edma3";
+				reg = <0x44000000 0x200000>;
+				#dma-cells = <3>;
+				dma-channels = <31>;
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+				clock-names = "dma";
+			};
+
 			mu1: mailbox@44220000 {
 				compatible = "fsl,imx95-mu";
 				reg = <0x44220000 0x10000>;
@@ -830,6 +1053,8 @@ lpi2c1: i2c@44340000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma1 12 0 0>, <&edma1 13 0 FSL_EDMA_RX> ;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -842,6 +1067,8 @@ lpi2c2: i2c@44350000 {
 				clock-names = "per", "ipg";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				dmas = <&edma1 14 0 0>, <&edma1 15 0 FSL_EDMA_RX> ;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -854,6 +1081,8 @@ lpspi1: spi@44360000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
 					 <&scmi_clk IMX95_CLK_BUSAON>;
 				clock-names = "per", "ipg";
+				dmas = <&edma1 16 0 FSL_EDMA_RX>, <&edma1 17 0 0> ;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -866,6 +1095,8 @@ lpspi2: spi@44370000 {
 				clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
 					 <&scmi_clk IMX95_CLK_BUSAON>;
 				clock-names = "per", "ipg";
+				dmas = <&edma1 18 0 FSL_EDMA_RX>, <&edma1 19 0 0> ;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -876,6 +1107,8 @@ lpuart1: serial@44380000 {
 				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART1>;
 				clock-names = "ipg";
+				dmas = <&edma1 21 0 FSL_EDMA_RX>, <&edma1 20 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -886,6 +1119,8 @@ lpuart2: serial@44390000 {
 				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&scmi_clk IMX95_CLK_LPUART2>;
 				clock-names = "ipg";
+				dmas = <&edma1 23 0 FSL_EDMA_RX>, <&edma1 22 0 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
-- 
2.34.1

[PATCH v2 2/7] arm64: dts: imx95: add sai[1..6], xcvr and micfill

[Frank Li]

Add sai[1..6], NXP Audio Transceiver (XCVR) Controller and  MICFIL Digital
Audio Interface (MICFIL).

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Change from v1 to v2
- Add Peng Fan's review tag
---
 arch/arm64/boot/dts/freescale/imx95.dtsi | 111 +++++++++++++++++++++++
 1 file changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
index 12f7ac52c2589..d32127cf7018a 100644
--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -222,6 +222,13 @@ core5 {
 		};
 	};
 
+	dummy: clock-dummy {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+		clock-output-names = "dummy";
+	};
+
 	clk_ext1: clock-ext1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -706,6 +713,64 @@ lpuart6: serial@425a0000 {
 				status = "disabled";
 			};
 
+			sai3: sai@42650000 {
+				compatible = "fsl,imx95-sai";
+				reg = <0x42650000 0x10000>;
+				interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>, <&dummy>,
+					 <&scmi_clk IMX95_CLK_SAI3>, <&dummy>,
+					 <&dummy>;
+				clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+				dmas = <&edma2 61 0 FSL_EDMA_RX>, <&edma2 60 0 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai4: sai@42660000 {
+				compatible = "fsl,imx95-sai";
+				reg = <0x42660000 0x10000>;
+				interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>, <&dummy>,
+					 <&scmi_clk IMX95_CLK_SAI4>, <&dummy>,
+					 <&dummy>;
+				clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+				dmas = <&edma2 68 0 FSL_EDMA_RX>, <&edma2 67 0 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai5: sai@42670000 {
+				compatible = "fsl,imx95-sai";
+				reg = <0x42670000 0x10000>;
+				interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>, <&dummy>,
+					 <&scmi_clk IMX95_CLK_SAI5>, <&dummy>,
+					 <&dummy>;
+				clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+				dmas = <&edma2 70 0 FSL_EDMA_RX>, <&edma2 69 0 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			xcvr: xcvr@42680000 {
+				compatible = "fsl,imx95-xcvr";
+				reg = <0x42680000 0x800>, <0x42680800 0x400>,
+				      <0x42680c00 0x080>, <0x42680e00 0x080>;
+				reg-names = "ram", "regs", "rxfifo", "txfifo";
+				interrupts = /* XCVR IRQ 0 */
+					     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+					     /* XCVR IRQ 1 */
+					     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+					 <&scmi_clk IMX95_CLK_SPDIF>,
+					 <&dummy>,
+					 <&scmi_clk IMX95_CLK_AUDIOXCVR>;
+				clock-names = "ipg", "phy", "spba", "pll_ipg";
+				dmas = <&edma2 65 0 1>, <&edma2 66 0 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
 			lpuart7: serial@42690000 {
 				compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
 					     "fsl,imx7ulp-lpuart";
@@ -1124,6 +1189,38 @@ lpuart2: serial@44390000 {
 				status = "disabled";
 			};
 
+			sai1: sai@443b0000 {
+				compatible = "fsl,imx95-sai";
+				reg = <0x443b0000 0x10000>;
+				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSAON>, <&dummy>,
+					 <&scmi_clk IMX95_CLK_SAI1>, <&dummy>,
+					 <&dummy>;
+				clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+				dmas = <&edma1 25 0 FSL_EDMA_RX>, <&edma1 24 0 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			micfil: micfil@44520000 {
+				compatible = "fsl,imx95-micfil", "fsl,imx93-micfil";
+				reg = <0x44520000 0x10000>;
+				interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_BUSAON>,
+					 <&scmi_clk IMX95_CLK_PDM>,
+					 <&scmi_clk IMX95_CLK_AUDIOPLL1>,
+					 <&scmi_clk IMX95_CLK_AUDIOPLL2>,
+					 <&dummy>;
+				clock-names = "ipg_clk", "ipg_clk_app",
+					      "pll8k", "pll11k", "clkext3";
+				dmas = <&edma1 6 0 5>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
 			adc1: adc@44530000 {
 				compatible = "nxp,imx93-adc";
 				reg = <0x44530000 0x10000>;
@@ -1423,5 +1520,19 @@ pcie1_ep: pcie-ep@4c380000 {
 			power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
 			status = "disabled";
 		};
+
+		sai2: sai@4c880000 {
+			compatible = "fsl,imx95-sai";
+			reg = <0x0 0x4c880000 0x0 0x10000>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scmi_clk IMX95_CLK_BUSNETCMIX>, <&dummy>,
+				 <&scmi_clk IMX95_CLK_SAI2>, <&dummy>,
+				 <&dummy>;
+			clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+			power-domains = <&scmi_devpd IMX95_PD_NETC>;
+			dmas = <&edma2 59 0 FSL_EDMA_RX>, <&edma2 58 0 0>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
 	};
 };
-- 
2.34.1

[PATCH v2 3/7] arm64: dts: imx95-19x19-evk: Add audio related nodes

[Frank Li]

Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change from v1 to v2
- none
---
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 238 ++++++++++++++++++
 1 file changed, 238 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index d14a54ab4fd47..660e623f4f964 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -17,6 +17,11 @@ aliases {
 		serial0 = &lpuart1;
 	};
 
+	bt_sco_codec: audio-codec-bt-sco {
+		#sound-dai-cells = <1>;
+		compatible = "linux,bt-sco";
+	};
+
 	chosen {
 		stdout-path = &lpuart1;
 	};
@@ -40,6 +45,34 @@ linux_cma: linux,cma {
 		};
 	};
 
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SW";
+	};
+
+	reg_audio_pwr: regulator-audio-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&i2c4_gpio_expander_21 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_audio_slot: regulator-audio-slot {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-wm8962";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&i2c4_gpio_expander_21 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		status = "disabled";
+	};
+
 	reg_m2_pwr: regulator-m2-pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "M.2-power";
@@ -79,6 +112,97 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
 		enable-active-high;
 		off-on-delay-us = <12000>;
 	};
+
+	sound-bt-sco {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "bt-sco-audio";
+		simple-audio-card,format = "dsp_a";
+		simple-audio-card,bitclock-inversion;
+		simple-audio-card,frame-master = <&btcpu>;
+		simple-audio-card,bitclock-master = <&btcpu>;
+
+		btcpu: simple-audio-card,cpu {
+			sound-dai = <&sai1>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&bt_sco_codec 1>;
+		};
+	};
+
+	sound-micfil {
+		compatible = "fsl,imx-audio-card";
+		model = "micfil-audio";
+
+		pri-dai-link {
+			link-name = "micfil hifi";
+			format = "i2s";
+			cpu {
+				sound-dai = <&micfil>;
+			};
+		};
+	};
+
+	sound-wm8962 {
+		compatible = "fsl,imx-audio-wm8962";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
+		model = "wm8962-audio";
+		audio-cpu = <&sai3>;
+		audio-codec = <&wm8962>;
+		hp-det-gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		audio-routing = "Headphone Jack", "HPOUTL",
+				"Headphone Jack", "HPOUTR",
+				"Ext Spk", "SPKOUTL",
+				"Ext Spk", "SPKOUTR",
+				"AMIC", "MICBIAS",
+				"IN3R", "AMIC",
+				"IN1R", "AMIC";
+	};
+};
+
+&lpi2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c4>;
+	status = "okay";
+
+	wm8962: audio-codec@1a {
+		compatible = "wlf,wm8962";
+		reg = <0x1a>;
+		clocks = <&scmi_clk IMX95_CLK_SAI3>;
+		DCVDD-supply = <&reg_audio_pwr>;
+		DBVDD-supply = <&reg_audio_pwr>;
+		AVDD-supply = <&reg_audio_pwr>;
+		CPVDD-supply = <&reg_audio_pwr>;
+		MICVDD-supply = <&reg_audio_pwr>;
+		PLLVDD-supply = <&reg_audio_pwr>;
+		SPKVDD1-supply = <&reg_audio_pwr>;
+		SPKVDD2-supply = <&reg_audio_pwr>;
+		gpio-cfg = < 0x0000 /* 0:Default */
+			     0x0000 /* 1:Default */
+			     0x0000 /* 2:FN_DMICCLK */
+			     0x0000 /* 3:Default */
+			     0x0000 /* 4:FN_DMICCDAT */
+			     0x0000 /* 5:Default */
+			   >;
+	};
+
+	i2c4_gpio_expander_21: gpio@21 {
+		compatible = "nxp,pcal6408";
+		reg = <0x21>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c4_pcal6408>;
+		vcc-supply = <&reg_3p3v>;
+	};
 };
 
 &lpi2c7 {
@@ -108,6 +232,23 @@ &lpuart1 {
 	status = "okay";
 };
 
+&micfil {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pdm>;
+	assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL1>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2>,
+			  <&scmi_clk IMX95_CLK_PDM>;
+	assigned-clock-parents = <0>, <0>, <0>, <0>,
+				 <&scmi_clk IMX95_CLK_AUDIOPLL1>;
+	assigned-clock-rates = <3932160000>,
+			       <3612672000>, <393216000>,
+			       <361267200>, <49152000>;
+	status = "okay";
+};
+
 &mu7 {
 	status = "okay";
 };
@@ -128,6 +269,42 @@ &pcie1 {
 	status = "okay";
 };
 
+&sai1 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL1>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2>,
+			  <&scmi_clk IMX95_CLK_SAI1>;
+	assigned-clock-parents = <0>, <0>, <0>, <0>,
+				 <&scmi_clk IMX95_CLK_AUDIOPLL1>;
+	assigned-clock-rates = <3932160000>,
+			       <3612672000>, <393216000>,
+			       <361267200>, <12288000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&sai3 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL1>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2>,
+			  <&scmi_clk IMX95_CLK_SAI3>;
+	assigned-clock-parents = <0>, <0>, <0>, <0>,
+				 <&scmi_clk IMX95_CLK_AUDIOPLL1>;
+	assigned-clock-rates = <3932160000>,
+			       <3612672000>, <393216000>,
+			       <361267200>, <12288000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -159,12 +336,31 @@ &wdog3 {
 };
 
 &scmi_iomuxc {
+	pinctrl_hp: hpgrp {
+		fsl,pins = <
+			IMX95_PAD_GPIO_IO11__GPIO2_IO_BIT11		0x31e
+		>;
+	};
+
+	pinctrl_i2c4_pcal6408: i2c4pcal6498grp {
+		fsl,pins = <
+			IMX95_PAD_GPIO_IO18__GPIO2_IO_BIT18			0x31e
+		>;
+	};
+
 	pinctrl_i2c7_pcal6524: i2c7pcal6524grp {
 		fsl,pins = <
 			IMX95_PAD_GPIO_IO36__GPIO5_IO_BIT16			0x31e
 		>;
 	};
 
+	pinctrl_lpi2c4: lpi2c4grp {
+		fsl,pins = <
+			IMX95_PAD_GPIO_IO30__LPI2C4_SDA			0x40000b9e
+			IMX95_PAD_GPIO_IO31__LPI2C4_SCL			0x40000b9e
+		>;
+	};
+
 	pinctrl_lpi2c7: lpi2c7grp {
 		fsl,pins = <
 			IMX95_PAD_GPIO_IO08__LPI2C7_SDA			0x40000b9e
@@ -184,6 +380,48 @@ IMX95_PAD_GPIO_IO35__HSIOMIX_TOP_PCIE2_CLKREQ_B		0x4000031e
 		>;
 	};
 
+	pinctrl_pdm: pdmgrp {
+		fsl,pins = <
+			IMX95_PAD_PDM_CLK__AONMIX_TOP_PDM_CLK				0x31e
+			IMX95_PAD_PDM_BIT_STREAM0__AONMIX_TOP_PDM_BIT_STREAM_BIT0	0x31e
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			IMX95_PAD_SAI1_RXD0__AONMIX_TOP_SAI1_RX_DATA_BIT0    0x31e
+			IMX95_PAD_SAI1_TXC__AONMIX_TOP_SAI1_TX_BCLK      0x31e
+			IMX95_PAD_SAI1_TXFS__AONMIX_TOP_SAI1_TX_SYNC     0x31e
+			IMX95_PAD_SAI1_TXD0__AONMIX_TOP_SAI1_TX_DATA_BIT0    0x31e
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_SAI2_RX_BCLK			0x31e
+			IMX95_PAD_ENET2_MDC__NETCMIX_TOP_SAI2_RX_SYNC			0x31e
+			IMX95_PAD_ENET2_TD3__NETCMIX_TOP_SAI2_RX_DATA_BIT0		0x31e
+			IMX95_PAD_ENET2_TD2__NETCMIX_TOP_SAI2_RX_DATA_BIT1		0x31e
+			IMX95_PAD_ENET2_TXC__NETCMIX_TOP_SAI2_TX_BCLK			0x31e
+			IMX95_PAD_ENET2_TX_CTL__NETCMIX_TOP_SAI2_TX_SYNC		0x31e
+			IMX95_PAD_ENET2_RX_CTL__NETCMIX_TOP_SAI2_TX_DATA_BIT0		0x31e
+			IMX95_PAD_ENET2_RXC__NETCMIX_TOP_SAI2_TX_DATA_BIT1		0x31e
+			IMX95_PAD_ENET2_RD0__NETCMIX_TOP_SAI2_TX_DATA_BIT2		0x31e
+			IMX95_PAD_ENET2_RD1__NETCMIX_TOP_SAI2_TX_DATA_BIT3		0x31e
+			IMX95_PAD_ENET2_RD2__NETCMIX_TOP_SAI2_MCLK			0x31e
+		>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			IMX95_PAD_GPIO_IO17__SAI3_MCLK				0x31e
+			IMX95_PAD_GPIO_IO16__SAI3_TX_BCLK			0x31e
+			IMX95_PAD_GPIO_IO26__SAI3_TX_SYNC			0x31e
+			IMX95_PAD_GPIO_IO20__SAI3_RX_DATA_BIT0			0x31e
+			IMX95_PAD_GPIO_IO21__SAI3_TX_DATA_BIT0			0x31e
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			IMX95_PAD_UART1_RXD__AONMIX_TOP_LPUART1_RX      0x31e
-- 
2.34.1

[PATCH v2 4/7] arm64: dts: imx95: add flexspi node

[Frank Li]

Add flexspi support.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Change from v1 to v2
- add Peng fan's review tag
---
 arch/arm64/boot/dts/freescale/imx95.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
index d32127cf7018a..0870c0d13e041 100644
--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -713,6 +713,22 @@ lpuart6: serial@425a0000 {
 				status = "disabled";
 			};
 
+			flexspi1: spi@425e0000 {
+				compatible = "nxp,imx8mm-fspi";
+				reg = <0x425e0000 0x10000>, <0x28000000 0x8000000>;
+				reg-names = "fspi_base", "fspi_mmap";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&scmi_clk IMX95_CLK_FLEXSPI1>,
+					 <&scmi_clk IMX95_CLK_FLEXSPI1>;
+				clock-names = "fspi_en", "fspi";
+				assigned-clocks = <&scmi_clk IMX95_CLK_FLEXSPI1>;
+				assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
+				assigned-clock-rates = <200000000>;
+				status = "disabled";
+			};
+
 			sai3: sai@42650000 {
 				compatible = "fsl,imx95-sai";
 				reg = <0x42650000 0x10000>;
-- 
2.34.1

[PATCH v2 5/7] arm64: dts: imx95-19x19-evk: add flexspi and child node

[Frank Li]

Add flexspi and child flash node.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Change from v1 to v2
- move gpio pinctrl inder flash@0
- add reset-gpios
---
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index 660e623f4f964..2b820a961c173 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -163,6 +163,25 @@ sound-wm8962 {
 	};
 };
 
+&flexspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexspi1_reset>;
+		reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <200000000>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+	};
+};
+
 &lpi2c4 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -336,6 +355,28 @@ &wdog3 {
 };
 
 &scmi_iomuxc {
+	pinctrl_flexspi1: flexspi1grp {
+		fsl,pins = <
+			IMX95_PAD_XSPI1_SS0_B__FLEXSPI1_A_SS0_B			0x3fe
+			IMX95_PAD_XSPI1_SCLK__FLEXSPI1_A_SCLK			0x3fe
+			IMX95_PAD_XSPI1_DQS__FLEXSPI1_A_DQS			0x3fe
+			IMX95_PAD_XSPI1_DATA0__FLEXSPI1_A_DATA_BIT0		0x3fe
+			IMX95_PAD_XSPI1_DATA1__FLEXSPI1_A_DATA_BIT1		0x3fe
+			IMX95_PAD_XSPI1_DATA2__FLEXSPI1_A_DATA_BIT2		0x3fe
+			IMX95_PAD_XSPI1_DATA3__FLEXSPI1_A_DATA_BIT3		0x3fe
+			IMX95_PAD_XSPI1_DATA4__FLEXSPI1_A_DATA_BIT4		0x3fe
+			IMX95_PAD_XSPI1_DATA5__FLEXSPI1_A_DATA_BIT5		0x3fe
+			IMX95_PAD_XSPI1_DATA6__FLEXSPI1_A_DATA_BIT6		0x3fe
+			IMX95_PAD_XSPI1_DATA7__FLEXSPI1_A_DATA_BIT7		0x3fe
+		>;
+	};
+
+	pinctrl_flexspi1_reset: flexspi1-reset-grp {
+		fsl,pins = <
+			IMX95_PAD_XSPI1_SS1_B__GPIO5_IO_BIT11			0x3fe
+		>;
+	};
+
 	pinctrl_hp: hpgrp {
 		fsl,pins = <
 			IMX95_PAD_GPIO_IO11__GPIO2_IO_BIT11		0x31e
-- 
2.34.1

[PATCH v2 6/7] arm64: dts: imx95: add thermal_zone label

[Frank Li]

Add thermal_zone label because it may be overwrite by board level dts file.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change from v1 to v2
- add peng fan's review tag
---
 arch/arm64/boot/dts/freescale/imx95.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
index 0870c0d13e041..e454240ab3b04 100644
--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -326,7 +326,7 @@ pmu {
 		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
 	};
 
-	thermal-zones {
+	thermal_zones: thermal-zones {
 		a55-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <2000>;
-- 
2.34.1

[PATCH v2 7/7] arm64: dts: imx95-19x19-evk: add pwm fan control

[Frank Li]

Add pwm fan and overwrite default thermal nodes.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Change from v1 to v2
- Add tpm6 node
---
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 61 +++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index 2b820a961c173..37a1d4ca1b207 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/pwm/pwm.h>
 #include "imx95.dtsi"
 
 / {
@@ -31,6 +32,13 @@ memory@80000000 {
 		reg = <0x0 0x80000000 0 0x80000000>;
 	};
 
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		#cooling-cells = <2>;
+		pwms = <&tpm6 2 4000000 PWM_POLARITY_INVERTED>;
+		cooling-levels = <64 128 192 255>;
+	};
+
 	reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -463,6 +471,12 @@ IMX95_PAD_GPIO_IO21__SAI3_TX_DATA_BIT0			0x31e
 		>;
 	};
 
+	pinctrl_tpm6: tpm6grp {
+		fsl,pins = <
+			IMX95_PAD_GPIO_IO19__TPM6_CH2			0x51e
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			IMX95_PAD_UART1_RXD__AONMIX_TOP_LPUART1_RX      0x31e
@@ -566,3 +580,50 @@ IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT		0x51e
 		>;
 	};
 };
+
+&thermal_zones {
+	a55-thermal {
+		trips {
+			atrip2: trip2 {
+				temperature = <55000>;
+				hysteresis = <2000>;
+				type = "active";
+			};
+
+			atrip3: trip3 {
+				temperature = <65000>;
+				hysteresis = <2000>;
+				type = "active";
+			};
+
+			atrip4: trip4 {
+				temperature = <75000>;
+				hysteresis = <2000>;
+				type = "active";
+			};
+		};
+
+		cooling-maps {
+			map1 {
+				trip = <&atrip2>;
+				cooling-device = <&fan0 0 1>;
+			};
+
+			map2 {
+				trip = <&atrip3>;
+				cooling-device = <&fan0 1 2>;
+			};
+
+			map3 {
+				trip = <&atrip4>;
+				cooling-device = <&fan0 2 3>;
+			};
+		};
+	};
+};
+
+&tpm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm6>;
+	status = "okay";
+};
-- 
2.34.1

Re: [PATCH v2 1/7] arm64: dts: imx95: add edma[1..3] nodes

[Shawn Guo]

On Mon, Jul 01, 2024 at 04:07:22PM -0400, Frank Li wrote:
> Add eDMA1, eDMA2 and eDMA3 support for iMX95.
> Add dmas and dma-names for each peripheral, which use eDMA.
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>

Applied all, thanks!