[PATCH v3 0/3] Add support for Kontron OSM-S i.MX8MP SoM and carrier boards

[PATCH v3 0/3] Add support for Kontron OSM-S i.MX8MP SoM and carrier boards

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Patch 1: board DT bindings
Patch 2: OSM-S i.MX8MP SoM and BL carrier board devicetrees
Patch 3: i.MX8MP SMARC module and eval carrier board devicetrees

Changes for v3:

* Address Shawn's review comments (thanks!)
* Fix HDMI DDC interface
* Fix gpio-hog pinctrl in DL devicetree
* Fix DT check warnings in DL devicetree
* Adjust LVDS panel node to match that of proposed DL i.MX8MM

Changes for v2:

DT bindings (patch1):
* Add tags from Krzysztof and Conor (thanks!)

SMARC DTs (patch 3):
* Fix GPIO labels
* Add support for TPM chip on SMARC module
* Disable PWM in favor of GPIO5 on SMARC carrier
* Enable LCDIF node to make HDMI work
* Add support for GPIO expanders on SMARC carrier
* Remove SPI flash as its removable and should be in an overlay
* Add CAN regulators to fix transceiver enable

Frieder Schrempf (3):
  dt-bindings: arm: fsl: Add Kontron i.MX8MP OSM-S based boards
  arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier
    board
  arm64: dts: Add support for Kontron i.MX8MP SMARC module and eval
    carrier

 .../devicetree/bindings/arm/fsl.yaml          |  13 +
 arch/arm64/boot/dts/freescale/Makefile        |   6 +
 .../dts/freescale/imx8mp-kontron-bl-osm-s.dts | 305 ++++++
 .../boot/dts/freescale/imx8mp-kontron-dl.dtso | 110 +++
 .../dts/freescale/imx8mp-kontron-osm-s.dtsi   | 908 ++++++++++++++++++
 .../imx8mp-kontron-smarc-eval-carrier.dts     | 254 +++++
 .../dts/freescale/imx8mp-kontron-smarc.dtsi   | 280 ++++++
 7 files changed, 1876 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtso
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-osm-s.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi

-- 
2.46.0

[PATCH v3 1/3] dt-bindings: arm: fsl: Add Kontron i.MX8MP OSM-S based boards

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Add the bindings for the Kontron i.MX8MP OSM-S SoM and carrier
boards.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes for v3:
* none

Changes for v2:
* Add tags from Krzysztof and Conor (thanks!)
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 80747d79418a0..b59449f435ebd 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1113,6 +1113,19 @@ properties:
           - const: engicam,icore-mx8mp             # i.MX8MP Engicam i.Core MX8M Plus SoM
           - const: fsl,imx8mp
 
+      - description: Kontron i.MX8MP OSM-S SoM based Boards
+        items:
+          - const: kontron,imx8mp-bl-osm-s  # Kontron BL i.MX8MP OSM-S Board
+          - const: kontron,imx8mp-osm-s     # Kontron i.MX8MP OSM-S SoM
+          - const: fsl,imx8mp
+
+      - description: Kontron i.MX8MP SMARC based Boards
+        items:
+          - const: kontron,imx8mp-smarc-eval-carrier  # Kontron i.MX8MP SMARC Eval Carrier
+          - const: kontron,imx8mp-smarc               # Kontron i.MX8MP SMARC Module
+          - const: kontron,imx8mp-osm-s               # Kontron i.MX8MP OSM-S SoM
+          - const: fsl,imx8mp
+
       - description: PHYTEC phyCORE-i.MX8MP SoM based boards
         items:
           - const: phytec,imx8mp-phyboard-pollux-rdk # phyBOARD-Pollux RDK
-- 
2.46.0

[PATCH v3 2/3] arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This adds support for the Kontron Electronics OSM-S i.MX8MP SoM
and the matching baseboard BL i.MX8MP.

The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S (https://sget.org/standards/osm).

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Note: This depends on binding changes for the LVDS panel proposed here:

https://patchwork.ozlabs.org/project/devicetree-bindings/cover/20240828074753.25401-1-frieder@fris.de/

Note: This might throw the following warnings:

Warning (graph_port): /fragment@3: graph port node name should be 'port'
Warning (graph_endpoint): /fragment@3/__overlay__: graph endpoint node name should be 'endpoint'
Warning (graph_endpoint): /fragment@3/__overlay__: graph connection to node '/fragment@7/__overlay__/ports/port@0/endpoint' is not bidirectional

The following fix is available in DTC and queued in linux-next:

84b056a89d ("checks: relax graph checks for overlays")

https://git.kernel.org/pub/scm/utils/dtc/dtc.git/commit/?id=84b056a89d3c5b6cf6c5eeeafd4c4b14d6333aa9

Changes for v3:
* Fix HDMI DDC interface
* Fix gpio-hog pinctrl in DL devicetree
* Fix DT check warnings in DL devicetree
* Adjust LVDS panel node to match that of proposed DL i.MX8MM
* Address Shawn's review comments (thanks!)

Changes for v2:
* none
---
 arch/arm64/boot/dts/freescale/Makefile        |   5 +
 .../dts/freescale/imx8mp-kontron-bl-osm-s.dts | 305 ++++++
 .../boot/dts/freescale/imx8mp-kontron-dl.dtso | 110 +++
 .../dts/freescale/imx8mp-kontron-osm-s.dtsi   | 908 ++++++++++++++++++
 4 files changed, 1328 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtso
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-osm-s.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index f04c22b7de72e..e6f177e5fac26 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -171,6 +171,11 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-bl-osm-s.dtb
+
+imx8mp-kontron-dl-dtbs += imx8mp-kontron-bl-osm-s.dtb imx8mp-kontron-dl.dtbo
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-dl.dtb
+
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts
new file mode 100644
index 0000000000000..0eb9e726a9b81
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mp-kontron-osm-s.dtsi"
+
+/ {
+	model = "Kontron BL i.MX8MP OSM-S";
+	compatible = "kontron,imx8mp-bl-osm-s", "kontron,imx8mp-osm-s", "fsl,imx8mp";
+
+	aliases {
+		ethernet0 = &fec;
+		ethernet1 = &eqos;
+	};
+
+	extcon_usbc: usbc {
+		compatible = "linux,extcon-usb-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_id>;
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm2 0 5000 0>;
+	};
+
+	reg_vcc_panel: regulator-vcc-panel {
+		compatible = "regulator-fixed";
+		gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_PANEL";
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	eeram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&eqos {	/* Second ethernet (OSM-S ETH_B) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos_rgmii>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id4f51.e91b";
+			reg = <1>;
+			pinctrl-0 = <&pinctrl_ethphy1>;
+			pinctrl-names = "default";
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&fec { /* First ethernet (OSM-S ETH_A) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_rgmii>;
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id4f51.e91b";
+			reg = <1>;
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+/*
+ * Rename SoM signals according to board usage:
+ *   SDIO_A_PWR_EN -> CAN_ADDR2
+ *   SDIO_A_WP     -> CAN_ADDR3
+ */
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio2>;
+	gpio-line-names = "", "", "", "", "", "", "", "", "", "", "", "",
+			  "SDIO_A_CD", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
+			  "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "CAN_ADDR2",
+			  "CAN_ADDR3";
+};
+
+/*
+ * Rename SoM signals according to board usage:
+ *   SPI_A_WP      -> CAN_ADDR0
+ *   SPI_A_HOLD    -> CAN_ADDR1
+ *   GPIO_B_0      -> DIO1_OUT
+ *   GPIO_B_1      -> DIO2_OUT
+ */
+&gpio3 {
+	gpio-line-names = "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_A_PERST", "SDIO_B_D5",
+			  "SDIO_B_D6", "SDIO_B_D7", "CAN_ADDR0", "CAN_ADDR1",
+			  "UART_B_RTS", "UART_B_CTS", "SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "SDIO_B_WP", "SDIO_B_D4",
+			  "PCIE_SM_ALERT", "SDIO_B_CLK", "SDIO_B_CMD", "DIO1_OUT",
+			  "DIO2_OUT", "", "BOOT_SEL0", "BOOT_SEL1",
+			  "", "", "SDIO_B_CD", "SDIO_B_PWR_EN",
+			  "HDMI_CEC", "HDMI_HPD";
+};
+
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_5      -> DIO2_IN
+ *   GPIO_B_6      -> DIO3_IN
+ *   GPIO_B_7      -> DIO4_IN
+ *   GPIO_B_3      -> DIO4_OUT
+ *   GPIO_B_4      -> DIO1_IN
+ *   GPIO_B_2      -> DIO3_OUT
+ */
+&gpio4 {
+	gpio-line-names = "DIO2_IN", "DIO3_IN", "DIO4_IN", "GPIO_C_0",
+			  "ETH_A_MDC", "ETH_A_MDIO", "ETH_A_RXD0", "ETH_A_RXD1",
+			  "ETH_A_RXD2", "ETH_A_RXD3", "ETH_A_RX_DV", "ETH_A_RX_CLK",
+			  "ETH_A_TXD0", "ETH_A_TXD1", "ETH_A_TXD2", "ETH_A_TXD3",
+			  "ETH_A_TX_EN", "ETH_A_TX_CLK", "DIO4_OUT", "DIO1_IN",
+			  "DIO3_OUT", "GPIO_A_6", "CAN_A_TX", "UART_A_CTS",
+			  "UART_A_RTS", "CAN_A_RX", "CAN_B_TX", "CAN_B_RX",
+			  "GPIO_A_7", "CARRIER_PWR_EN", "I2S_A_DATA_IN", "I2S_LRCLK";
+};
+
+&hdmi_pvi {
+	status = "okay";
+};
+
+&hdmi_tx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&hdmi_tx_phy {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	gpio_expander_dio: io-expander@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "DIO1_OUT","DIO1_IN", "DIO2_OUT","DIO2_IN",
+				  "DIO3_OUT","DIO3_IN", "DIO4_OUT","DIO4_IN";
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&lcdif3 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&reg_usdhc2_vcc {
+	status = "disabled";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+	dr_mode = "otg";
+	extcon = <&extcon_usbc>;
+	usb-role-switch;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_hub>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dr_mode = "host";
+	status = "okay";
+
+	usb-hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		reset-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	fsl,disable-port-power-control;
+	fsl,permanently-attached;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ethphy0: ethphy0grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01		0x46
+		>;
+	};
+
+	pinctrl_ethphy1: ethphy1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x46
+		>;
+	};
+
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x46
+			MX8MP_IOMUXC_SD2_WP__GPIO2_IO20			0x46
+		>;
+	};
+
+	pinctrl_usb_hub: usbhubgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14		0x46
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtso b/arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtso
new file mode 100644
index 0000000000000..134bdf156607c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtso
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2023 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mp-pinfunc.h"
+
+&{/} {
+	model = "Kontron DL i.MX8MP OSM-S";
+	compatible = "kontron,imx8mp-bl-osm-s", "kontron,imx8mp-osm-s", "fsl,imx8mp";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000 0>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <100>;
+	};
+
+	panel {
+		compatible = "jenson,bl-jt60050-01a", "panel-lvds";
+		backlight = <&backlight>;
+		data-mapping = "vesa-24";
+		enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_vcc_panel>;
+		height-mm = <86>;
+		width-mm = <154>;
+
+		panel-timing {
+			clock-frequency = <50000000>;
+			hactive = <1024>;
+			hback-porch = <160>;
+			hfront-porch = <160>;
+			hsync-len = <1>;
+			vactive = <600>;
+			vback-porch = <23>;
+			vfront-porch = <12>;
+			vsync-len = <1>;
+		};
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&ldb_lvds_ch0>;
+			};
+		};
+	};
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>, <&pinctrl_panel_stby>;
+
+	panel-rst-hog {
+		gpio-hog;
+		gpios = <21 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-reset";
+	};
+
+	panel-stby-hog {
+		gpio-hog;
+		gpios = <28 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-standby";
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <6 8>;
+		irq-gpios = <&gpio1 6 0>;
+		power-supply = <&reg_vcc_panel>;
+		reset-gpios = <&gpio1 7 0>;
+	};
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&ldb_lvds_ch0 {
+	remote-endpoint = <&panel_in_lvds0>;
+};
+
+&lvds_bridge {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_panel_stby: panelstbygrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28		0x19
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-kontron-osm-s.dtsi
new file mode 100644
index 0000000000000..e0e9f6f7616d9
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-osm-s.dtsi
@@ -0,0 +1,908 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx8mp.dtsi"
+
+/ {
+	model = "Kontron OSM-S i.MX8MP";
+	compatible = "kontron,imx8mp-osm-s", "fsl,imx8mp";
+
+	aliases {
+		rtc0 = &rv3028;
+		rtc1 = &snvs_rtc;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		/*
+		 * There are multiple SoM flavors with different DDR sizes.
+		 * The smallest is 1GB. For larger sizes the bootloader will
+		 * update the reg property.
+		 */
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "VBUS_USB_A";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_vbus>;
+		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "VBUS_USB_B";
+	};
+
+	reg_usdhc2_vcc: regulator-usdhc2-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_A";
+	};
+
+	reg_usdhc3_vcc: regulator-usdhc3-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc3_vcc>;
+		gpio = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_B";
+	};
+
+	reg_vdd_carrier: regulator-vdd-carrier {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
+		gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "VDD_CARRIER";
+
+		regulator-state-standby {
+			regulator-on-in-suspend;
+		};
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+
+		regulator-state-disk {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ecspi1 { /* OSM-S SPI_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+};
+
+&ecspi2 { /* OSM-S SPI_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+};
+
+&flexcan1 { /* OSM-S CAN_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+};
+
+&flexcan2 { /* OSM-S CAN_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+	gpio-line-names = "GPIO_A_0", "GPIO_A_1", "", "",
+			  "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+			  "GPIO_A_5", "USB_B_EN", "USB_A_ID", "USB_B_ID",
+			  "USB_A_EN", "USB_A_OC","CAM_MCK", "USB_B_OC",
+			  "ETH_B_MDC", "ETH_B_MDIO", "ETH_B_TXD3", "ETH_B_TXD2",
+			  "ETH_B_TXD1", "ETH_B_TXD0", "ETH_B_TX_EN", "ETH_B_TX_CLK",
+			  "ETH_B_RX_DV", "ETH_B_RX_CLK", "ETH_B_RXD0", "ETH_B_RXD1",
+			  "ETH_B_RXD2", "ETH_B_RXD3";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "", "", "", "", "", "", "", "", "",
+			  "SDIO_A_CD", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
+			  "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN",
+			  "SDIO_A_WP";
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio3>;
+	gpio-line-names = "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_A_PERST", "SDIO_B_D5",
+			  "SDIO_B_D6", "SDIO_B_D7", "SPI_A_WP", "SPI_A_HOLD",
+			  "UART_B_RTS", "UART_B_CTS", "SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "SDIO_B_WP", "SDIO_B_D4",
+			  "PCIE_SM_ALERT", "SDIO_B_CLK", "SDIO_B_CMD", "GPIO_B_0",
+			  "GPIO_B_1", "", "BOOT_SEL0", "BOOT_SEL1",
+			  "", "", "SDIO_B_CD", "SDIO_B_PWR_EN",
+			  "HDMI_CEC", "HDMI_HPD";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+	gpio-line-names = "GPIO_B_5", "GPIO_B_6", "GPIO_B_7", "GPIO_C_0",
+			  "ETH_A_MDC", "ETH_A_MDIO", "ETH_A_RXD0", "ETH_A_RXD1",
+			  "ETH_A_RXD2", "ETH_A_RXD3", "ETH_A_RX_DV", "ETH_A_RX_CLK",
+			  "ETH_A_TXD0", "ETH_A_TXD1", "ETH_A_TXD2", "ETH_A_TXD3",
+			  "ETH_A_TX_EN", "ETH_A_TX_CLK", "GPIO_B_3", "GPIO_B_4",
+			  "GPIO_B_2", "GPIO_A_6", "CAN_A_TX", "UART_A_CTS",
+			  "UART_A_RTS", "CAN_A_RX", "CAN_B_TX", "CAN_B_RX",
+			  "GPIO_A_7", "CARRIER_PWR_EN", "I2S_A_DATA_IN", "I2S_LRCLK";
+};
+
+&gpio5 {
+	gpio-line-names = "I2S_BITCLK", "I2S_A_DATA_OUT", "I2S_MCLK", "PWM_2",
+			  "PWM_1", "PWM_0", "SPI_A_SCK", "SPI_A_SDO",
+			  "SPI_A_SDI", "SPI_A_CS0", "SPI_B_SCK", "SPI_B_SDO",
+			  "SPI_B_SDI", "SPI_B_CS0", "I2C_A_SCL", "I2C_A_SDA",
+			  "I2C_B_SCL", "I2C_B_SDA", "PCIE_SMCLK", "PCIE_SMDAT",
+			  "I2C_CAM_SCL", "I2C_CAM_SDA", "UART_A_RX", "UART_A_TX",
+			  "UART_C_RX", "UART_C_TX", "UART_CON_RX", "UART_CON_TX",
+			  "UART_B_RX", "UART_B_TX";
+};
+
+&i2c1 { /* OSM-S I2C_A */
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c2 { /* OSM-S I2C_B */
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c3 { /* OSM-S PCIe SMDAT/SMCLK */
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c4 { /* OSM-S I2C_CAM */
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c5 { /* PMIC, EEPROM, RTC */
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c5>;
+	pinctrl-1 = <&pinctrl_i2c5_gpio>;
+	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		nxp,i2c-lt-enable;
+
+		regulators {
+			reg_vdd_soc: BUCK1 { /* dual phase with BUCK3 */
+				regulator-name = "+0V8_VDD_SOC (BUCK1)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				regulator-name = "+0V9_VDD_ARM (BUCK2)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-name = "+3V3 (BUCK4)";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-name = "+1V8 (BUCK5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-name = "+1V8_NVCC_SNVS (LDO1)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdda: LDO3 {
+				regulator-name = "+1V8_VDDA (LDO3)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-name = "NVCC_SD (LDO5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	eeprom@50 {
+		compatible = "onnn,n24s64b", "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		size = <8192>;
+		num-addresses = <1>;
+	};
+
+	rv3028: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupts-extended = <&gpio3 24 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pwm1 { /* OSM-S PWM_0 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&pwm2 { /* OSM-S PWM_1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+&pwm3 { /* OSM-S PWM_2 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&sai3 { /* OSM-S I2S_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+};
+
+&uart1 { /* OSM-S UART_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart2 { /* OSM-S UART_C */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+};
+
+&uart3 { /* OSM-S UART_CON */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 { /* OSM-S UART_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usb3_0 { /* OSM-S USB_A */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_oc>;
+	fsl,over-current-active-low;
+};
+
+&usb3_1 { /* OSM-S USB_B */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb2_oc>;
+	fsl,over-current-active-low;
+};
+
+&usdhc1 { /* eMMC */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_vdd_1v8>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 { /* OSM-S SDIO_A */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>, <&pinctrl_usdhc2_wp>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>, <&pinctrl_usdhc2_wp>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>, <&pinctrl_usdhc2_wp>;
+	vmmc-supply = <&reg_usdhc2_vcc>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+};
+
+&usdhc3 { /* OSM-S SDIO_B */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+	vmmc-supply = <&reg_usdhc3_vcc>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_csi_mck: csimckgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO14__CCM_CLKO1		0x59 /* CAM_MCK */
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO		0x44 /* SPI_A_SDI_(IO0) */
+			MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI		0x44 /* SPI_A_SDO_(IO1) */
+			MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK		0x44 /* SPI_A_SCK */
+			MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09		0x40 /* SPI_A_CS0# */
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO		0x44 /* SPI_B_SDI */
+			MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI		0x44 /* SPI_B_SDO */
+			MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK		0x44 /* SPI_B_SCK */
+			MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13		0x40 /* SPI_B_CS0# */
+		>;
+	};
+
+	pinctrl_enet_rgmii: enetrgmiigrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3 /* ETH_MDC */
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3 /* ETH_MDIO */
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91 /* ETH_A_(S)(R)(G)MII_RXD0 */
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91 /* ETH_A_(S)(R)(G)MII_RXD1 */
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91 /* ETH_A_(R)(G)MII_RXD2 */
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91 /* ETH_A_(R)(G)MII_RXD3 */
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91 /* ETH_A_(R)(G)MII_RX_CLK */
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f /* ETH_A_(S)(R)(G)MII_TXD0 */
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f /* ETH_A_(S)(R)(G)MII_TXD1 */
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f /* ETH_A_(S)(R)(G)MII_TXD2 */
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f /* ETH_A_(S)(R)(G)MII_TXD3 */
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f /* ETH_A_(R)(G)MII_TX_CLK */
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+		>;
+	};
+
+	pinctrl_eqos_rgmii: eqosrgmiigrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC		0x3 /* ETH_B_MDC */
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO		0x3 /* ETH_B_MDIO */
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0	0x91 /* ETH_B_(S)(R)(G)MII_RXD0 */
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1	0x91 /* ETH_B_(S)(R)(G)MII_RXD1 */
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2	0x91 /* ETH_B_(R)(G)MII_RXD2 */
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3	0x91 /* ETH_B_(R)(G)MII_RXD3 */
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 /* ETH_B_(R)(G)MII_RX_CLK */
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x91 /* ETH_B_(R)(G)MII_RX_DV(_ER) */
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0	0x1f /* ETH_B_(S)(R)(G)MII_TXD0 */
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1	0x1f /* ETH_B_(S)(R)(G)MII_TXD1 */
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2	0x1f /* ETH_B_(S)(R)(G)MII_TXD2 */
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3	0x1f /* ETH_B_(S)(R)(G)MII_TXD3 */
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f /* ETH_B_(R)(G)MII_TX_CLK */
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x1f /* ETH_B_(R)(G)MII_TX_EN(_ER) */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_RXC__CAN1_TX			0x154 /* CAN_A_TX */
+			MX8MP_IOMUXC_SAI2_TXC__CAN1_RX			0x154 /* CAN_A_RX */
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_TXD0__CAN2_TX			0x154 /* CAN_B_TX */
+			MX8MP_IOMUXC_SAI2_MCLK__CAN2_RX			0x154 /* CAN_B_RX */
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x19 /* GPIO_A_0 */
+			MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01		0x19 /* GPIO_A_1 */
+			MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05		0x19 /* GPIO_A_2 */
+			MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x19 /* GPIO_A_3 */
+			MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07		0x19 /* GPIO_A_4 */
+			MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08		0x19 /* GPIO_A_5 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_CE0_B__GPIO3_IO01		0x19 /* GPIO_A_7 */
+			MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19		0x19 /* GPIO_B_0 */
+			MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x19 /* GPIO_B_1 */
+			MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22		0x19 /* BOOT_SEL0# */
+			MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23		0x19 /* BOOT_SEL1# */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00		0x19 /* GPIO_B_5 */
+			MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01		0x19 /* GPIO_B_6 */
+			MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02		0x19 /* GPIO_B_7 */
+			MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03		0x19 /* GPIO_C_0 */
+			MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18		0x19 /* GPIO_B_3 */
+			MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19		0x19 /* GPIO_B_4 */
+			MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20		0x19 /* GPIO_B_2 */
+			MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21		0x19 /* GPIO_A_6 */
+		>;
+	};
+
+	pinctrl_hdmi: hdmigrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD		0x19 /* HDMI_HPD */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL			0x40000084 /* I2C_A_SCL */
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA			0x40000084 /* I2C_A_SDA */
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14		0x84 /* I2C_A_SCL */
+			MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15		0x84 /* I2C_A_SDA */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL			0x40000084 /* I2C_B_SCL */
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA			0x40000084 /* I2C_B_SDA */
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16		0x84 /* I2C_B_SCL */
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17		0x84 /* I2C_B_SDA */
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL			0x40000084 /* PCIe_SMCLK */
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA			0x40000084 /* PCIe_SMDAT */
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18		0x84 /* PCIe_SMCLK */
+			MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19		0x84 /* PCIe_SMDAT */
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL			0x40000084 /* I2C_CAM_SCL/CSI_TX_P */
+			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA			0x40000084 /* I2C_CAM_SDA/CSI_TX_N */
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20		0x84 /* I2C_CAM_SCL/CSI_TX_P */
+			MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21		0x84 /* I2C_CAM_SDA/CSI_TX_N */
+		>;
+	};
+
+	pinctrl_i2c5: i2c5grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD0__I2C5_SCL		0x40000084
+			MX8MP_IOMUXC_SAI5_MCLK__I2C5_SDA		0x40000084
+		>;
+	};
+
+	pinctrl_i2c5_gpio: i2c5gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21		0x84
+			MX8MP_IOMUXC_SAI5_MCLK__GPIO3_IO25		0x84
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART4_RXD__PCIE_CLKREQ_B		0x19 /* PCIe_CLKREQ# */
+			MX8MP_IOMUXC_NAND_CE1_B__GPIO3_IO02		0x19 /* PCIe_A_PERST# */
+			MX8MP_IOMUXC_NAND_ALE__GPIO3_IO00		0x19 /* PCIe_WAKE# */
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16		0x19 /* PCIe_SM_ALERT */
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x1c0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT		0x6 /* PWM_0 */
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_RX__PWM2_OUT			0x6 /* PWM_1 */
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_TX__PWM3_OUT			0x6 /* PWM_2 */
+		>;
+	};
+
+	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12		0x19 /* USB_A_EN */
+		>;
+	};
+
+	pinctrl_reg_usb2_vbus: regusb2vbusgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09		0x19 /* USB_B_EN */
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x19 /* SDIO_A_PWR_EN */
+		>;
+	};
+
+	pinctrl_reg_usdhc3_vcc: regusdhc3vccgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_DDC_SDA__GPIO3_IO27		0x19 /* SDIO_B_PWR_EN */
+		>;
+	};
+
+	pinctrl_reg_vdd_carrier: regvddcarriergrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29		0x19 /* CARRIER_PWR_EN */
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD3__GPIO3_IO24		0x1c0
+		>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXD__AUDIOMIX_SAI3_RX_DATA00		0xd6 /* I2S_A_DATA_IN */
+			MX8MP_IOMUXC_SAI3_TXD__AUDIOMIX_SAI3_TX_DATA00		0xd6 /* I2S_A_DATA_OUT */
+			MX8MP_IOMUXC_SAI3_RXFS__AUDIOMIX_SAI3_RX_DATA01		0xd6 /* I2S_B_DATA_IN */
+			MX8MP_IOMUXC_SAI3_TXFS__AUDIOMIX_SAI3_TX_DATA01		0xd6 /* I2S_B_DATA_OUT */
+			MX8MP_IOMUXC_SAI3_MCLK__AUDIOMIX_SAI3_MCLK		0xd6 /* I2S_MCLK */
+			MX8MP_IOMUXC_NAND_DATA01__AUDIOMIX_SAI3_TX_SYNC		0xd6 /* I2S_LRCLK */
+			MX8MP_IOMUXC_SAI3_TXC__AUDIOMIX_SAI3_TX_BCLK		0xd6 /* I2S_BITCLK */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX		0x140 /* UART_A_RX */
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX		0x140 /* UART_A_TX */
+			MX8MP_IOMUXC_SAI2_RXD0__UART1_DCE_RTS		0x140 /* UART_A_CTS */
+			MX8MP_IOMUXC_SAI2_TXFS__UART1_DCE_CTS		0x140 /* UART_A_RTS */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX		0x140 /* UART_C_RX */
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX		0x140 /* UART_C_TX */
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX		0x140 /* UART_CON_RX */
+			MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX		0x140 /* UART_CON_TX */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DATA00__UART4_DCE_RX		0x140 /* UART_B_RX */
+			MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX		0x140 /* UART_B_TX */
+			MX8MP_IOMUXC_NAND_DATA03__UART4_DCE_RTS		0x140 /* UART_B_CTS */
+			MX8MP_IOMUXC_NAND_DATA02__UART4_DCE_CTS		0x140 /* UART_B_RTS */
+		>;
+	};
+
+	pinctrl_usb1_id: usb1idgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10		0x1c4 /* USB_A_ID */
+		>;
+	};
+
+	pinctrl_usb1_oc: usb1ocgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC		0x1c0 /* USB_A_OC# */
+		>;
+	};
+
+	pinctrl_usb2_id: usb2idgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO11__USB2_OTG_ID		0x1c4 /* USB_B_ID */
+		>;
+	};
+
+	pinctrl_usb2_oc: usb2ocgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO15__USB2_OTG_OC		0x1c0 /* USB_B_OC# */
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x190
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d0
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d0
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d0
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d0
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d0
+			MX8MP_IOMUXC_SD1_DATA4__USDHC1_DATA4		0x1d0
+			MX8MP_IOMUXC_SD1_DATA5__USDHC1_DATA5		0x1d0
+			MX8MP_IOMUXC_SD1_DATA6__USDHC1_DATA6		0x1d0
+			MX8MP_IOMUXC_SD1_DATA7__USDHC1_DATA7		0x1d0
+			MX8MP_IOMUXC_SD1_RESET_B__USDHC1_RESET_B	0x141
+			MX8MP_IOMUXC_SD1_STROBE__USDHC1_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x194
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d4
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d4
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d4
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d4
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d4
+			MX8MP_IOMUXC_SD1_DATA4__USDHC1_DATA4		0x1d4
+			MX8MP_IOMUXC_SD1_DATA5__USDHC1_DATA5		0x1d4
+			MX8MP_IOMUXC_SD1_DATA6__USDHC1_DATA6		0x1d4
+			MX8MP_IOMUXC_SD1_DATA7__USDHC1_DATA7		0x1d4
+			MX8MP_IOMUXC_SD1_RESET_B__USDHC1_RESET_B	0x141
+			MX8MP_IOMUXC_SD1_STROBE__USDHC1_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x196
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d6
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d6
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d6
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d6
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d6
+			MX8MP_IOMUXC_SD1_DATA4__USDHC1_DATA4		0x1d6
+			MX8MP_IOMUXC_SD1_DATA5__USDHC1_DATA5		0x1d6
+			MX8MP_IOMUXC_SD1_DATA6__USDHC1_DATA6		0x1d6
+			MX8MP_IOMUXC_SD1_DATA7__USDHC1_DATA7		0x1d6
+			MX8MP_IOMUXC_SD1_RESET_B__USDHC1_RESET_B	0x141
+			MX8MP_IOMUXC_SD1_STROBE__USDHC1_STROBE		0x196
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190 /* SDIO_A_CLK */
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0 /* SDIO_A_CMD */
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0 /* SDIO_A_D0 */
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0 /* SDIO_A_D1 */
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0 /* SDIO_A_D2 */
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0 /* SDIO_A_D3 */
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194 /* SDIO_A_CLK */
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4 /* SDIO_A_CMD */
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4 /* SDIO_A_D0 */
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4 /* SDIO_A_D1 */
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4 /* SDIO_A_D2 */
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4 /* SDIO_A_D3 */
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196 /* SDIO_A_CLK */
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6 /* SDIO_A_CMD */
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6 /* SDIO_A_D0 */
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6 /* SDIO_A_D1 */
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6 /* SDIO_A_D2 */
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6 /* SDIO_A_D3 */
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x19 /* SDIO_A_CD# */
+		>;
+	};
+
+	pinctrl_usdhc2_wp: usdhc2wpgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_WP__USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x190 /* SDIO_B_CLK */
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d0 /* SDIO_B_CMD */
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d0 /* SDIO_B_D0 */
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d0 /* SDIO_B_D1 */
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d0 /* SDIO_B_D2 */
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d0 /* SDIO_B_D3 */
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d0 /* SDIO_B_D4 */
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d0 /* SDIO_B_D5 */
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d0 /* SDIO_B_D6 */
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d0 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194 /* SDIO_B_CLK */
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4 /* SDIO_B_CMD */
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d4 /* SDIO_B_D0 */
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d4 /* SDIO_B_D1 */
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d4 /* SDIO_B_D2 */
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d4 /* SDIO_B_D3 */
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d4 /* SDIO_B_D4 */
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d4 /* SDIO_B_D5 */
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d4 /* SDIO_B_D6 */
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x196 /* SDIO_B_CLK */
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d6 /* SDIO_B_CMD */
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d6 /* SDIO_B_D0 */
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d6 /* SDIO_B_D1 */
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d6 /* SDIO_B_D2 */
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d6 /* SDIO_B_D3 */
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d6 /* SDIO_B_D4 */
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d6 /* SDIO_B_D5 */
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d6 /* SDIO_B_D6 */
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d6 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_gpio: usdhc3gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_DDC_SCL__GPIO3_IO26		0x19 /* SDIO_B_CD# */
+			MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14		0x19 /* SDIO_B_WP */
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
-- 
2.46.0

[PATCH v3 3/3] arm64: dts: Add support for Kontron i.MX8MP SMARC module and eval carrier

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This adds support for the Kontron Electronics i.MX8MP SMARC module
(which uses the OSM-S i.MX8MP SoM) on the Kontron SMARC eval carrier.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes for v3:
* Address Shawn's review comments (thanks!)

Changes for v2:
* Fix GPIO labels
* Add support for TPM chip on SMARC module
* Disable PWM in favor of GPIO5 on SMARC carrier
* Enable LCDIF node to make HDMI work
* Add support for GPIO expanders on SMARC carrier
* Remove SPI flash as its removable and should be in an overlay
* Add CAN regulators to fix transceiver enable
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../imx8mp-kontron-smarc-eval-carrier.dts     | 254 ++++++++++++++++
 .../dts/freescale/imx8mp-kontron-smarc.dtsi   | 280 ++++++++++++++++++
 3 files changed, 535 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index e6f177e5fac26..250a7db037282 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -176,6 +176,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-bl-osm-s.dtb
 imx8mp-kontron-dl-dtbs += imx8mp-kontron-bl-osm-s.dtb imx8mp-kontron-dl.dtbo
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-dl.dtb
 
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-kontron-smarc-eval-carrier.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
new file mode 100644
index 0000000000000..2173a36ff6917
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2024 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mp-kontron-smarc.dtsi"
+
+/ {
+	model = "Kontron SMARC Eval Carrier with i.MX8MP";
+	compatible = "kontron,imx8mp-smarc-eval-carrier", "kontron,imx8mp-smarc",
+		     "kontron,imx8mp-osm-s", "fsl,imx8mp";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000 0>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <100>;
+		enable-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	};
+
+	extcon_usbc: usbc {
+		compatible = "linux,extcon-usb-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_id>;
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,name = "imx8mp-wm8904";
+		simple-audio-card,routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Headphone Jack", "MICBIAS",
+			"IN1L", "Headphone Jack";
+		simple-audio-card,widgets =
+			"Microphone", "Headphone Jack",
+			"Headphone", "Headphone Jack",
+			"Line", "Line In Jack";
+
+		codec_dai: simple-audio-card,codec {
+			clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK1>;
+			sound-dai = <&wm8904>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+	};
+
+	regulator_can0: can0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "can0_en";
+		gpio = <&expander_pm_out 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	regulator_can1: can1-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "can1_en";
+		gpio = <&expander_pm_out 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	status = "okay";
+};
+
+&ecspi2 {
+	status = "okay";
+};
+
+&eqos {
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&flexcan1 {
+	xceiver-supply = <&regulator_can0>;
+	status = "okay";
+};
+
+&flexcan2 {
+	xceiver-supply = <&regulator_can1>;
+	status = "okay";
+};
+
+&hdmi_pvi {
+	status = "okay";
+};
+
+&hdmi_tx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	ddc-i2c-bus = <&i2c3>;
+	status = "okay";
+};
+
+&hdmi_tx_phy {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	expander_pm_out: io-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "EN_5V0_S0", "EN_3V3_S0", "EN_1V8_S0",
+				  "EN_1V5_S0", "EN_12V0_PCIE", "EN_3V3_S5",
+				  "CAN0_EN", "CAN1_EN";
+	};
+
+	expander_pm_in: io-expander@24 {
+		compatible = "nxp,pca9554";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PG_5V0_3V3_S0", "PG_5V0_3V3_S5", "PG_1V8_S0",
+				  "PG_1V5_S0", "PG_BKLT_5V", "PG_BKLT_12V";
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	wm8904: audio-codec@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+		clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI3_MCLK1>;
+		clock-names = "mclk";
+		AVDD-supply = <&reg_vdd_1v8>;
+		CPVDD-supply = <&reg_vdd_1v8>;
+		DBVDD-supply = <&reg_vdd_1v8>;
+		DCVDD-supply = <&reg_vdd_1v8>;
+		MICVDD-supply = <&reg_vdd_3v3>;
+	};
+
+	expander_audio: io-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "I2C_SEL_CODEC_LOOPBACK", "FPAH_PRESENCE",
+				  "CODEC_OPTION_SW_I2S_HDA", "LINE_IN_JD",
+				  "LINE_OUT_JD", "HEADPHONES_JD", "MIC_JD";
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&lcdif3 {
+	status = "okay";
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&hsio_blk_ctrl>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&sai3 {
+	assigned-clocks = <&clk IMX8MP_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MP_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+	dr_mode = "otg";
+	extcon = <&extcon_usbc>;
+	usb-role-switch;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usdhc2 {
+	vmmc-supply = <&reg_vdd_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi
new file mode 100644
index 0000000000000..1e831d9b8a935
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2024 Kontron Electronics GmbH
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mp-kontron-osm-s.dtsi"
+
+/ {
+	model = "Kontron SMARC i.MX8MP";
+	compatible = "kontron,imx8mp-smarc", "kontron,imx8mp-osm-s", "fsl,imx8mp";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ecspi1 {
+	status = "okay";
+
+	tpm@0 {
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+		reg = <0>;
+		spi-max-frequency = <18500000>;
+	};
+};
+
+&eqos {	/* Second ethernet (OSM-S ETH_B) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos_rgmii>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id4f51.e91b";
+			reg = <1>;
+			pinctrl-0 = <&pinctrl_ethphy1>;
+			pinctrl-names = "default";
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&fec { /* First ethernet (OSM-S ETH_A) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_rgmii>;
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id4f51.e91b";
+			reg = <1>;
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/*
+ * Rename SoM signals according to SMARC module usage:
+ *   GPIO_A_2 -> GPIO0
+ *   GPIO_A_3 -> GPIO1
+ *   GPIO_A_4 -> GPIO2
+ *   GPIO_A_5 -> GPIO3
+ *   USB_B_EN -> n.a.
+ *   USB_B_ID -> n.a.
+ *   USB_B_OC -> n.a.
+ */
+&gpio1 {
+	gpio-line-names = "GPIO_A_0", "GPIO_A_1", "", "",
+			  "", "GPIO0", "GPIO1", "GPIO2",
+			  "GPIO3", "", "USB_A_ID", "",
+			  "USB_A_EN", "USB_A_OC","CAM_MCK", "",
+			  "ETH_B_MDC", "ETH_B_MDIO", "ETH_B_TXD3", "ETH_B_TXD2",
+			  "ETH_B_TXD1", "ETH_B_TXD0", "ETH_B_TX_EN", "ETH_B_TX_CLK",
+			  "ETH_B_RX_DV", "ETH_B_RX_CLK", "ETH_B_RXD0", "ETH_B_RXD1",
+			  "ETH_B_RXD2", "ETH_B_RXD3";
+};
+
+/*
+ * Rename SoM signals according to SMARC module usage:
+ *   SDIO_A_CD -> SDIO_CD
+ *   SDIO_A_CLK -> SDIO_CK
+ *   SDIO_A_CMD -> SDIO_CMD
+ *   SDIO_A_D0 -> SDIO_D0
+ *   SDIO_A_D1 -> SDIO_D1
+ *   SDIO_A_D2 -> SDIO_D2
+ *   SDIO_A_D3 -> SDIO_D3
+ *   SDIO_A_PWR_EN -> SDIO_PWR_EN
+ *   SDIO_A_WP -> SDIO_WP
+ */
+&gpio2 {
+	gpio-line-names = "", "", "", "", "", "", "", "", "", "", "", "",
+			  "SDIO_CD", "SDIO_CK", "SDIO_CMD", "SDIO_D0",
+			  "SDIO_D1", "SDIO_D2", "SDIO_D3", "SDIO_PWR_EN",
+			  "SDIO_WP";
+};
+
+/*
+ * Rename SoM signals according to SMARC module usage:
+ *   PCIE_CLKREQ -> PCIE_A_CKREQ
+ *   PCIE_A_PERST -> PCIE_A_RST
+ *   SDIO_B_D5 -> n.a.
+ *   SDIO_B_D6 -> n.a.
+ *   SDIO_B_D7 -> n.a.
+ *   SPI_A_WP -> n.a.
+ *   SPI_A_HOLD -> n.a.
+ *   UART_B_RTS -> SER2_RTS
+ *   UART_B_CTS -> SER2_CTS
+ *   SDIO_B_D0 -> GPIO8
+ *   SDIO_B_D1 -> GPIO9
+ *   SDIO_B_D2 -> GPIO10
+ *   SDIO_B_D3 -> GPIO11
+ *   SDIO_B_WP -> n.a.
+ *   SDIO_B_D4 -> n.a.
+ *   PCIE_SM_ALERT -> SMB_ALERT
+ *   SDIO_B_CLK -> GPIO6
+ *   SDIO_B_CMD -> GPIO7
+ *   GPIO_B_0 -> LCD0_BKLT_EN
+ *   GPIO_B_1 -> LCD1_BKLT_EN
+ *   BOOT_SEL0 -> BOOT_SEL2
+ *   SDIO_B_CD -> n.a.
+ *   SDIO_B_PWR_EN -> n.a.
+ *   HDMI_CEC -> n.a.
+ *   SDIO_B_PWR_EN -> n.a.
+ */
+&gpio3 {
+	pinctrl-0 = <&pinctrl_gpio3>, <&pinctrl_gpio3_smarc>;
+	gpio-line-names = "PCIE_WAKE", "PCIE_A_CKREQ", "PCIE_A_RST", "",
+			  "", "", "", "",
+			  "SER2_RTS", "SER2_CTS", "GPIO8", "GPIO9",
+			  "GPIO10", "GPIO11", "", "",
+			  "SMB_ALERT", "GPIO6", "GPIO7", "LCD0_BKLT_EN",
+			  "LCD1_BKLT_EN", "", "BOOT_SEL2", "BOOT_SEL1",
+			  "", "", "", "",
+			  "", "HDMI_HPD";
+};
+
+/*
+ * Rename SoM signals according to SMARC module usage:
+ *   GPIO_B_5 -> n.a.
+ *   GPIO_B_6 -> n.a.
+ *   GPIO_B_7 -> n.a.
+ *   GPIO_C_0 -> LED
+ *   GPIO_B_3 -> ETH2_INT
+ *   GPIO_B_4 -> USB_HUB_RST
+ *   GPIO_B_2 -> ETH1_INT
+ *   GPIO_A_6 -> GPIO4
+ *   CAN_A_TX -> CAN0_TX
+ *   UART_A_CTS -> SER0_CTS
+ *   UART_A_RTS -> SER0_RTS
+ *   CAN_A_RX -> CAN0_RX
+ *   CAN_B_TX -> CAN1_TX
+ *   CAN_B_RX -> CAN1_RX
+ *   GPIO_A_7 -> TEST
+ *   I2S_A_DATA_IN -> I2S0_SDIN
+ *   I2S_LRCLK -> I2S0_LRCK
+ */
+&gpio4 {
+	gpio-line-names = "", "", "", "LED",
+			  "ETH_A_MDC", "ETH_A_MDIO", "ETH_A_RXD0", "ETH_A_RXD1",
+			  "ETH_A_RXD2", "ETH_A_RXD3", "ETH_A_RX_DV", "ETH_A_RX_CLK",
+			  "ETH_A_TXD0", "ETH_A_TXD1", "ETH_A_TXD2", "ETH_A_TXD3",
+			  "ETH_A_TX_EN", "ETH_A_TX_CLK", "ETH2_INT", "USB_HUB_RST",
+			  "ETH1_INT", "GPIO4", "CAN0_TX", "SER0_CTS",
+			  "SER0_RTS", "CAN0_RX", "CAN1_TX", "CAN1_RX",
+			  "TEST", "CARRIER_PWR_EN", "I2S0_SDIN", "I2S0_LRCK";
+};
+
+/*
+ * Rename SoM signals according to SMARC module usage:
+ *   I2S_BITCLK -> I2S0_CK
+ *   I2S_A_DATA_OUT -> I2S0_SDOUT
+ *   I2S_MCLK -> AUDIO_MCK
+ *   PWM_2 -> GPIO5
+ *   PWM_1 -> LCD1_BKLT_PWM
+ *   PWM_0 -> LCD0_BKLT_PWM
+ *   SPI_A_SCK -> SPI0_CK
+ *   SPI_A_SDO -> SPI0_DO
+ *   SPI_A_SDI -> SPI0_DIN
+ *   SPI_A_CS0 -> SPI0_CS0
+ *   SPI_B_SCK -> ESPI_CK
+ *   SPI_B_SDO -> ESPI_IO_0
+ *   SPI_B_SDI -> ESPI_IO_1
+ *   SPI_B_CS0 -> ESPI_CS0
+ *   I2C_A_SCL -> I2C_PM_CK
+ *   I2C_A_SDA -> I2C_PM_DAT
+ *   I2C_B_SCL -> I2C_GP_CK
+ *   I2C_B_SDA -> I2C_GP_DAT
+ *   PCIE_SMCLK -> HDMI_CTRL_CK
+ *   PCIE_SMDAT -> HDMI_CTRL_DAT
+ *   I2C_CAM_SCL -> I2C_CAM1_CK
+ *   I2C_CAM_SDA -> I2C_CAM1_DAT
+ *   UART_A_RX -> SER0_RX
+ *   UART_A_TX -> SER0_TX
+ *   UART_C_RX -> SER3_RX
+ *   UART_C_TX -> SER3_TX
+ *   UART_CON_RX -> SER1_RX
+ *   UART_CON_TX -> SER1_TX
+ *   UART_B_RX -> SER2_RX
+ *   UART_B_TX -> SER2_TX
+ */
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio5_smarc>;
+	gpio-line-names = "I2S0_CK", "I2S0_SDOUT", "AUDIO_MCK", "GPIO5",
+			  "LCD1_BKLT_PWM", "LCD0_BKLT_PWM", "SPI0_CK", "SPI0_DO",
+			  "SPI0_DIN", "SPI0_CS0", "ESPI_CK", "ESPI_IO_0",
+			  "ESPI_IO_1", "ESPI_CS0", "I2C_PM_CK", "I2C_PM_DAT",
+			  "I2C_GP_CK", "I2C_GP_DAT", "HDMI_CTRL_CK", "HDMI_CTRL_DAT",
+			  "I2C_CAM1_CK", "I2C_CAM1_DAT", "SER0_RX", "SER0_TX",
+			  "SER3_RX", "SER3_TX", "SER1_RX", "SER1_TX",
+			  "SER2_RX", "SER2_TX";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb-hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&usb3_1 {
+	fsl,disable-port-power-control;
+	fsl,permanently-attached;
+};
+
+&iomuxc {
+	pinctrl_ethphy0: ethphy0grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01		0x46
+		>;
+	};
+
+	pinctrl_ethphy1: ethphy1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x46
+		>;
+	};
+
+	pinctrl_gpio3_smarc: gpio3smarcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DATA04__GPIO3_IO10		0x1d0 /* SMARC GPIO8 */
+			MX8MP_IOMUXC_NAND_DATA05__GPIO3_IO11		0x1d0 /* SMARC GPIO9 */
+			MX8MP_IOMUXC_NAND_DATA06__GPIO3_IO12		0x1d0 /* SMARC GPIO10 */
+			MX8MP_IOMUXC_NAND_DATA07__GPIO3_IO13		0x1d0 /* SMARC GPIO11 */
+			MX8MP_IOMUXC_NAND_WE_B__GPIO3_IO17		0x190 /* SMARC GPIO6 */
+			MX8MP_IOMUXC_NAND_WP_B__GPIO3_IO18		0x1d0 /* SMARC GPIO7 */
+		>;
+	};
+
+	pinctrl_gpio5_smarc: gpio5smarcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_RX__GPIO5_IO04		0x1d0 /* SMARC GPIO5 */
+		>;
+	};
+};
-- 
2.46.0

Re: [PATCH v3 0/3] Add support for Kontron OSM-S i.MX8MP SoM and carrier boards

[Rob Herring (Arm)]

On Wed, 04 Sep 2024 10:53:18 +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> Patch 1: board DT bindings
> Patch 2: OSM-S i.MX8MP SoM and BL carrier board devicetrees
> Patch 3: i.MX8MP SMARC module and eval carrier board devicetrees
> 
> Changes for v3:
> 
> * Address Shawn's review comments (thanks!)
> * Fix HDMI DDC interface
> * Fix gpio-hog pinctrl in DL devicetree
> * Fix DT check warnings in DL devicetree
> * Adjust LVDS panel node to match that of proposed DL i.MX8MM
> 
> Changes for v2:
> 
> DT bindings (patch1):
> * Add tags from Krzysztof and Conor (thanks!)
> 
> SMARC DTs (patch 3):
> * Fix GPIO labels
> * Add support for TPM chip on SMARC module
> * Disable PWM in favor of GPIO5 on SMARC carrier
> * Enable LCDIF node to make HDMI work
> * Add support for GPIO expanders on SMARC carrier
> * Remove SPI flash as its removable and should be in an overlay
> * Add CAN regulators to fix transceiver enable
> 
> Frieder Schrempf (3):
>   dt-bindings: arm: fsl: Add Kontron i.MX8MP OSM-S based boards
>   arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier
>     board
>   arm64: dts: Add support for Kontron i.MX8MP SMARC module and eval
>     carrier
> 
>  .../devicetree/bindings/arm/fsl.yaml          |  13 +
>  arch/arm64/boot/dts/freescale/Makefile        |   6 +
>  .../dts/freescale/imx8mp-kontron-bl-osm-s.dts | 305 ++++++
>  .../boot/dts/freescale/imx8mp-kontron-dl.dtso | 110 +++
>  .../dts/freescale/imx8mp-kontron-osm-s.dtsi   | 908 ++++++++++++++++++
>  .../imx8mp-kontron-smarc-eval-carrier.dts     | 254 +++++
>  .../dts/freescale/imx8mp-kontron-smarc.dtsi   | 280 ++++++
>  7 files changed, 1876 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtso
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-osm-s.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc.dtsi
> 
> --
> 2.46.0
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y freescale/imx8mp-kontron-bl-osm-s.dtb freescale/imx8mp-kontron-smarc-eval-carrier.dtb' for 20240904085415.645031-1-frieder@fris.de:

arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dtb: clock-controller@30e20000: '#reset-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/clock/imx8mp-audiomix.yaml#
arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dtb: clock-controller@30e20000: '#reset-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/clock/imx8mp-audiomix.yaml#
arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dtb: pcie-ep@33800000: reg: [[864026624, 1048576], [402653184, 134217728], [865075200, 1048576], [867172352, 1048576]] is too long
	from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space', 'dbi2', 'atu'] is too long
	from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dtb: pcie-ep@33800000: reg: [[864026624, 1048576], [402653184, 134217728], [865075200, 1048576], [867172352, 1048576]] is too long
	from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
arch/arm64/boot/dts/freescale/imx8mp-kontron-smarc-eval-carrier.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space', 'dbi2', 'atu'] is too long
	from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#

Re: [PATCH v3 0/3] Add support for Kontron OSM-S i.MX8MP SoM and carrier boards

[Frieder Schrempf]

On 04.09.24 10:53 AM, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> 
> Patch 1: board DT bindings
> Patch 2: OSM-S i.MX8MP SoM and BL carrier board devicetrees
> Patch 3: i.MX8MP SMARC module and eval carrier board devicetrees
> 
> Changes for v3:
> 
> * Address Shawn's review comments (thanks!)
> * Fix HDMI DDC interface
> * Fix gpio-hog pinctrl in DL devicetree
> * Fix DT check warnings in DL devicetree
> * Adjust LVDS panel node to match that of proposed DL i.MX8MM
> 
> Changes for v2:
> 
> DT bindings (patch1):
> * Add tags from Krzysztof and Conor (thanks!)
> 
> SMARC DTs (patch 3):
> * Fix GPIO labels
> * Add support for TPM chip on SMARC module
> * Disable PWM in favor of GPIO5 on SMARC carrier
> * Enable LCDIF node to make HDMI work
> * Add support for GPIO expanders on SMARC carrier
> * Remove SPI flash as its removable and should be in an overlay
> * Add CAN regulators to fix transceiver enable
> 
> Frieder Schrempf (3):
>   dt-bindings: arm: fsl: Add Kontron i.MX8MP OSM-S based boards
>   arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier
>     board
>   arm64: dts: Add support for Kontron i.MX8MP SMARC module and eval
>     carrier

Gentle ping for this series. Shawn, can you apply this for v6.13, please?

Thanks
Frieder

Re: [PATCH v3 0/3] Add support for Kontron OSM-S i.MX8MP SoM and carrier boards

[Shawn Guo]

On Wed, Sep 04, 2024 at 10:53:18AM +0200, Frieder Schrempf wrote:
> Frieder Schrempf (3):
>   dt-bindings: arm: fsl: Add Kontron i.MX8MP OSM-S based boards
>   arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier
>     board
>   arm64: dts: Add support for Kontron i.MX8MP SMARC module and eval
>     carrier

Applied all, thanks!