Re: [PATCH 2/2] mmc: mtk-sd: add support for AN7581 MMC Host

["Wenbin Mei (梅文彬)" <Wenbin.Mei@mediatek.com>]

On Wed, 2025-01-15 at 08:29 +0100, Christian Marangi wrote:
> External email : Please do not click links or open attachments until
> you have verified the sender or the content.
> 
> 
> Add support for AN7581 MMC Host. The MMC Host controller is based on
> mt7622 with the difference of not having regulator supply and
> state_uhs
> pins and hclk clock.
> 
> Some minor fixes are applied to check if the state_uhs pins are
> defined
> and make hclk optional for the new airoha compatible.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  drivers/mmc/host/mtk-sd.c | 55 ++++++++++++++++++++++++++++++++-----
> --
>  1 file changed, 46 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> index efb0d2d5716b..9d6868883c91 100644
> --- a/drivers/mmc/host/mtk-sd.c
> +++ b/drivers/mmc/host/mtk-sd.c
> @@ -666,6 +666,20 @@ static const struct mtk_mmc_compatible
> mt8196_compat = {
>         .support_new_rx = true,
>  };
> 
> +static const struct mtk_mmc_compatible an7581_compat = {
> +       .clk_div_bits = 12,
> +       .recheck_sdio_irq = true,
> +       .hs400_tune = false,
> +       .pad_tune_reg = MSDC_PAD_TUNE0,
> +       .async_fifo = true,
> +       .data_tune = true,
> +       .busy_check = true,
> +       .stop_clk_fix = true,
> +       .stop_dly_sel = 3,
> +       .enhance_rx = true,
> +       .support_64g = false,
> +};
> +
>  static const struct of_device_id msdc_of_ids[] = {
>         { .compatible = "mediatek,mt2701-mmc", .data =
> &mt2701_compat},
>         { .compatible = "mediatek,mt2712-mmc", .data =
> &mt2712_compat},
> @@ -680,7 +694,7 @@ static const struct of_device_id msdc_of_ids[] =
> {
>         { .compatible = "mediatek,mt8183-mmc", .data =
> &mt8183_compat},
>         { .compatible = "mediatek,mt8196-mmc", .data =
> &mt8196_compat},
>         { .compatible = "mediatek,mt8516-mmc", .data =
> &mt8516_compat},
> -
> +       { .compatible = "airoha,an7581-mmc", .data = &an7581_compat},
>         {}
>  };
>  MODULE_DEVICE_TABLE(of, msdc_of_ids);
> @@ -1600,6 +1614,10 @@ static int msdc_ops_switch_volt(struct
> mmc_host *mmc, struct mmc_ios *ios)
>         struct msdc_host *host = mmc_priv(mmc);
>         int ret;
> 
> +       /* Skip setting supply if not supported */
> +       if (!mmc->supply.vqmmc)
> +               return 0;
> +
>         if (!IS_ERR(mmc->supply.vqmmc)) {
>                 if (ios->signal_voltage != MMC_SIGNAL_VOLTAGE_330 &&
>                     ios->signal_voltage != MMC_SIGNAL_VOLTAGE_180) {
> @@ -1699,7 +1717,9 @@ static void msdc_enable_sdio_irq(struct
> mmc_host *mmc, int enb)
>                                 dev_dbg(host->dev, "SDIO eint irq:
> %d!\n", host->eint_irq);
>                         }
> 
> -                       pinctrl_select_state(host->pinctrl, host-
> >pins_uhs);
> +                       /* Skip setting uhs pins if not supported */
> +                       if (host->pins_uhs)
> +                               pinctrl_select_state(host->pinctrl,
> host->pins_uhs);
>                 } else {
>                         dev_pm_clear_wake_irq(host->dev);
>                 }
> @@ -2036,6 +2056,10 @@ static void msdc_ops_set_ios(struct mmc_host
> *mmc, struct mmc_ios *ios)
> 
>         msdc_set_buswidth(host, ios->bus_width);
> 
> +       /* Skip regulator if not supported */
> +       if (!mmc->supply.vmmc)
> +               goto skip_regulator;
> +
If power_mode is MMC_POWER_UP, we need to execute the related flow.
Now it will skip mmc_init_hw(host), which will cause problems.
BTW, can this be implemented using a fix regulator? if ok, no need
to modify here.
>         /* Suspend/Resume will do power off/on */
>         switch (ios->power_mode) {
>         case MMC_POWER_UP:
> @@ -2071,6 +2095,7 @@ static void msdc_ops_set_ios(struct mmc_host
> *mmc, struct mmc_ios *ios)
>                 break;
>         }
> 
> +skip_regulator:
>         if (host->mclk != ios->clock || host->timing != ios->timing)
>                 msdc_set_mclk(host, ios->timing, ios->clock);
>  }
> @@ -2816,9 +2841,12 @@ static int msdc_of_clock_parse(struct
> platform_device *pdev,
>         if (IS_ERR(host->src_clk))
>                 return PTR_ERR(host->src_clk);
> 
> -       host->h_clk = devm_clk_get(&pdev->dev, "hclk");
> -       if (IS_ERR(host->h_clk))
> -               return PTR_ERR(host->h_clk);
> +       /* AN7581 SoC doesn't have hclk */
> +       if (!device_is_compatible(&pdev->dev, "airoha,an7581-mmc")) {
> +               host->h_clk = devm_clk_get(&pdev->dev, "hclk");
> +               if (IS_ERR(host->h_clk))
> +                       return PTR_ERR(host->h_clk);
> +       }
> 
>         host->bus_clk = devm_clk_get_optional(&pdev->dev, "bus_clk");
>         if (IS_ERR(host->bus_clk))
> @@ -2926,10 +2954,13 @@ static int msdc_drv_probe(struct
> platform_device *pdev)
>                 return PTR_ERR(host->pins_default);
>         }
> 
> -       host->pins_uhs = pinctrl_lookup_state(host->pinctrl,
> "state_uhs");
> -       if (IS_ERR(host->pins_uhs)) {
> -               dev_err(&pdev->dev, "Cannot find pinctrl uhs!\n");
> -               return PTR_ERR(host->pins_uhs);
> +       /* AN7581 doesn't have state_uhs pins */
> +       if (!device_is_compatible(&pdev->dev, "airoha,an7581-mmc")) {
> +               host->pins_uhs = pinctrl_lookup_state(host->pinctrl,
> "state_uhs");
> +               if (IS_ERR(host->pins_uhs)) {
> +                       dev_err(&pdev->dev, "Cannot find pinctrl
> uhs!\n");
> +                       return PTR_ERR(host->pins_uhs);
> +               }
>         }
> 
>         /* Support for SDIO eint irq ? */
> @@ -3010,6 +3041,12 @@ static int msdc_drv_probe(struct
> platform_device *pdev)
>                 dev_err(&pdev->dev, "Cannot ungate clocks!\n");
>                 goto release_clk;
>         }
> +
> +       /* AN7581 without regulator require tune to OCR values */
> +       if (device_is_compatible(&pdev->dev, "airoha,an7581-mmc") &&
> +           !mmc->ocr_avail)
> +               mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
> +
>         msdc_init_hw(host);
> 
>         if (mmc->caps2 & MMC_CAP2_CQE) {
> --
> 2.45.2
>