Re: [PATCH v5 4/6] arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Add navigation mezzanine dts

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 12/11/2022 18:26, Bryan O'Donoghue wrote:
> Move the dts data for the rb3 navigation mezzanine into its own dts file.
> 
> Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/Makefile             |   1 +
>   .../sdm845-db845c-navigation-mezzanine.dts    | 107 ++++++++++++++++++
>   arch/arm64/boot/dts/qcom/sdm845-db845c.dts    |  99 ----------------
>   3 files changed, 108 insertions(+), 99 deletions(-)
>   create mode 100644 arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index d534888bcfe52..70ce09bc63a33 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -131,6 +131,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c-navigation-mezzanine.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyln.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyp.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
> new file mode 100644
> index 0000000000000..7bd0a15c72657
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
> @@ -0,0 +1,107 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2022, Linaro Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sdm845-db845c.dts"
> +
> +&cci {
> +	status = "okay";
> +};
> +
> +&camss {
camss goes before cci alphabetically.

Konrad
> +	vdda-phy-supply = <&vreg_l1a_0p875>;
> +	vdda-pll-supply = <&vreg_l26a_1p2>;
> +
> +	status = "okay";
> +
> +	ports {
> +		port@0 {
> +			reg = <0>;
> +			csiphy0_ep: endpoint {
> +				data-lanes = <0 1 2 3>;
> +				remote-endpoint = <&ov8856_ep>;
> +			};
> +		};
> +	};
> +};
> +
> +&cci_i2c0 {
> +	camera@10 {
> +		compatible = "ovti,ov8856";
> +		reg = <0x10>;
> +
> +		/* CAM0_RST_N */
> +		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&cam0_default>;
> +
> +		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
> +		clock-names = "xvclk";
> +		clock-frequency = <19200000>;
> +
> +		/*
> +		 * The &vreg_s4a_1p8 trace is powered on as a,
> +		 * so it is represented by a fixed regulator.
> +		 *
> +		 * The 2.8V vdda-supply and 1.2V vddd-supply regulators
> +		 * both have to be enabled through the power management
> +		 * gpios.
> +		 */
> +		dovdd-supply = <&vreg_lvs1a_1p8>;
> +		avdd-supply = <&cam0_avdd_2v8>;
> +		dvdd-supply = <&cam0_dvdd_1v2>;
> +
> +		status = "okay";
> +
> +		port {
> +			ov8856_ep: endpoint {
> +				link-frequencies = /bits/ 64
> +					<360000000 180000000>;
> +				data-lanes = <1 2 3 4>;
> +				remote-endpoint = <&csiphy0_ep>;
> +			};
> +		};
> +	};
> +};
> +
> +&cci_i2c1 {
> +	camera@60 {
> +		compatible = "ovti,ov7251";
> +
> +		/* I2C address as per ov7251.txt linux documentation */
> +		reg = <0x60>;
> +
> +		/* CAM3_RST_N */
> +		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&cam3_default>;
> +
> +		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
> +		clock-names = "xclk";
> +		clock-frequency = <24000000>;
> +
> +		/*
> +		 * The &vreg_s4a_1p8 trace always powered on.
> +		 *
> +		 * The 2.8V vdda-supply regulator is enabled when the
> +		 * vreg_s4a_1p8 trace is pulled high.
> +		 * It too is represented by a fixed regulator.
> +		 *
> +		 * No 1.2V vddd-supply regulator is used.
> +		 */
> +		vdddo-supply = <&vreg_lvs1a_1p8>;
> +		vdda-supply = <&cam3_avdd_2v8>;
> +
> +		status = "disabled";
> +
> +		port {
> +			ov7251_ep: endpoint {
> +				data-lanes = <0 1>;
> +/*				remote-endpoint = <&csiphy3_ep>; */
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> index 5da91c646c200..f41c6d600ea8c 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> @@ -1174,105 +1174,6 @@ &pm8998_gpio {
>   
>   };
>   
> -&cci {
> -	status = "okay";
> -};
> -
> -&camss {
> -	vdda-phy-supply = <&vreg_l1a_0p875>;
> -	vdda-pll-supply = <&vreg_l26a_1p2>;
> -
> -	status = "okay";
> -
> -	ports {
> -		port@0 {
> -			reg = <0>;
> -			csiphy0_ep: endpoint {
> -				data-lanes = <0 1 2 3>;
> -				remote-endpoint = <&ov8856_ep>;
> -			};
> -		};
> -	};
> -};
> -
> -&cci_i2c0 {
> -	camera@10 {
> -		compatible = "ovti,ov8856";
> -		reg = <0x10>;
> -
> -		/* CAM0_RST_N */
> -		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&cam0_default>;
> -
> -		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
> -		clock-names = "xvclk";
> -		clock-frequency = <19200000>;
> -
> -		/*
> -		 * The &vreg_s4a_1p8 trace is powered on as a,
> -		 * so it is represented by a fixed regulator.
> -		 *
> -		 * The 2.8V vdda-supply and 1.2V vddd-supply regulators
> -		 * both have to be enabled through the power management
> -		 * gpios.
> -		 */
> -		dovdd-supply = <&vreg_lvs1a_1p8>;
> -		avdd-supply = <&cam0_avdd_2v8>;
> -		dvdd-supply = <&cam0_dvdd_1v2>;
> -
> -		status = "okay";
> -
> -		port {
> -			ov8856_ep: endpoint {
> -				link-frequencies = /bits/ 64
> -					<360000000 180000000>;
> -				data-lanes = <1 2 3 4>;
> -				remote-endpoint = <&csiphy0_ep>;
> -			};
> -		};
> -	};
> -};
> -
> -&cci_i2c1 {
> -	camera@60 {
> -		compatible = "ovti,ov7251";
> -
> -		/* I2C address as per ov7251.txt linux documentation */
> -		reg = <0x60>;
> -
> -		/* CAM3_RST_N */
> -		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&cam3_default>;
> -
> -		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
> -		clock-names = "xclk";
> -		clock-frequency = <24000000>;
> -
> -		/*
> -		 * The &vreg_s4a_1p8 trace always powered on.
> -		 *
> -		 * The 2.8V vdda-supply regulator is enabled when the
> -		 * vreg_s4a_1p8 trace is pulled high.
> -		 * It too is represented by a fixed regulator.
> -		 *
> -		 * No 1.2V vddd-supply regulator is used.
> -		 */
> -		vdddo-supply = <&vreg_lvs1a_1p8>;
> -		vdda-supply = <&cam3_avdd_2v8>;
> -
> -		status = "disabled";
> -
> -		port {
> -			ov7251_ep: endpoint {
> -				data-lanes = <0 1>;
> -/*				remote-endpoint = <&csiphy3_ep>; */
> -			};
> -		};
> -	};
> -};
> -
>   /* PINCTRL - additions to nodes defined in sdm845.dtsi */
>   &qup_spi0_default {
>   	config {