Re: [PATCH v2 4/5] arm64: dts: qcom: ipq5332: Add thermal zone nodes

[Dmitry Baryshkov <dmitry.baryshkov@linaro.org>]

On 12/07/2023 14:35, Praveenkumar I wrote:
> This patch adds thermal zone nodes for sensors present in
> IPQ5332.
> 
> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
> ---
> [v2]:
> 	Added passive trips and alignment change.
> 
>   arch/arm64/boot/dts/qcom/ipq5332.dtsi | 78 +++++++++++++++++++++++++++
>   1 file changed, 78 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
> index 0eef77e36609..a1f59af97ee8 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
> @@ -480,4 +480,82 @@ timer {
>   			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>   			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>   	};
> +
> +	thermal-zones {
> +		rfa-0-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsens 11>;
> +
> +			trips {
> +				rfa-0-critical {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		rfa-1-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsens 12>;
> +
> +			trips {
> +				rfa-1-critical {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		misc-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsens 13>;
> +
> +			trips {
> +				misc-critical {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		cpu-top-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsens 14>;
> +
> +			trips {
> +				cpu-top-critical {
> +					temperature = <115000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +
> +				cpu-passive {
> +					temperature = <105000>;
> +					hysteresis = <1000>;
> +					type = "passive";

cooling device for this trip point?

> +				};
> +			};
> +		};
> +
> +		top-glue-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsens 15>;
> +
> +			trips {
> +				top-glue-critical {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
>   };

-- 
With best wishes
Dmitry