From: Alexandre TORGUE <alexandre.torgue@foss.st.com>
To: Steffen Trumtrar <s.trumtrar@pengutronix.de>,
<linux-stm32@st-md-mailman.stormreply.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v5 09/10] ARM: dts: stm32: add STM32MP1-based Phytec SoM
Date: Mon, 20 Mar 2023 18:37:52 +0100 [thread overview]
Message-ID: <a37db3a8-a3e6-8755-2b7c-c33a1fdca469@foss.st.com> (raw)
In-Reply-To: <20230320132755.2150384-10-s.trumtrar@pengutronix.de>
Hi Steffen
On 3/20/23 14:27, Steffen Trumtrar wrote:
> The Phytec STM32MP1 based SoMs feature up to 1 GB DDR3LP RAM, up to 1 GB
> eMMC, up to 16 MB QSPI and up to 128 GB NAND flash.
>
> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
> ---
>
> Notes:
> checkpatch warns about un-documented binding
>
> According to checkpatch the binding for "winbond,w25q128"
> used in this dtsi is un-documented.
> However, 'jedec,spi-nor.yaml' defines the pattern
>
> (winbond,)?w25q(16|32(w|dw)?|64(dw)?|80bl|128(fw)?|256))$"
>
> so, this should be good!?
We recently added some yaml fixes and we continue to send others (i.e.,
GPU yaml error fix is under review) so please don't add new ones. Some
of follownig errors are directly linked to your board so please fix them.
Thanks
Alex
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
codec@18: 'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/sound/ti,tlv320aic3x.yaml
arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
/soc/i2c@40012000/touch@44: failed to match any schema with compatible:
['st,stmpe811']
arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
/soc/i2c@40012000/touch@44/touchscreen: failed to match any schema with
compatible: ['st,stmpe-ts']
arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
/soc/i2c@40012000/leds@62: failed to match any schema with compatible:
['nxp,pca9533']
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
sai@4400b000: audio-controller@4400b004:port:endpoint: Unevaluated
properties are not allowed ('format' was unexpected)
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
sai@4400b000: audio-controller@4400b024:port:endpoint: Unevaluated
properties are not allowed ('format' was unexpected)
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
usbphyc@5a006000: usb-phy@0: 'vbus-supply' does not match any of the
regexes: 'pinctrl-[0-9]+'
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
pmic@33: regulators: 'vref-ddr', 'vref_ddr-supply' do not match any of
the regexes: '^(buck[1-4]|ldo[1-6]|boost|pwr_sw[1-2])-supply$',
'^(buck[1-4]|ldo[1-6]|boost|vref_ddr|pwr_sw[1-2])$', '^buck[1-4]$',
'^ldo[1-2,5-6]$', '^pwr_sw[1-2]$', 'pinctrl-[0-9]+'
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/mfd/st,stpmic1.yaml
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp1-3.dtb:
gpu@59000000: 'contiguous-area' does not match any of the regexes:
'pinctrl-[0-9]+'
From schema:
/local/home/frq08678/STLINUX/kernel/my-kernel/stm32/Documentation/devicetree/bindings/gpu/vivante,gc.yaml
>
> .../stm32mp157c-phycore-stm32mp15-som.dtsi | 609 ++++++++++++++++++
> 1 file changed, 609 insertions(+)
> create mode 100644 arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
>
> diff --git a/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi b/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
> new file mode 100644
> index 0000000000000..230863daca60b
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
> @@ -0,0 +1,609 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de>
> + * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
> + * Author: Dom VOVARD <dom.vovard@linrt.com>.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/leds/leds-pca9532.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include "stm32mp15-pinctrl.dtsi"
> +
> +/ {
> + model = "PHYTEC phyCORE-STM32MP15 SOM";
> + compatible = "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
> +
> + aliases {
> + ethernet0 = ðernet0;
> + rtc0 = &i2c4_rtc;
> + rtc1 = &rtc;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + key-home {
> + label = "Home";
> + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_HOME>;
> + };
> +
> + key-enter {
> + label = "Enter";
> + gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_ENTER>;
> + };
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + retram: retram@38000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x38000000 0x10000>;
> + no-map;
> + };
> +
> + mcuram: mcuram@30000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x30000000 0x40000>;
> + no-map;
> + };
> +
> + mcuram2: mcuram2@10000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10000000 0x40000>;
> + no-map;
> + };
> +
> + vdev0vring0: vdev0vring0@10040000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10040000 0x1000>;
> + no-map;
> + };
> +
> + vdev0vring1: vdev0vring1@10041000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10041000 0x1000>;
> + no-map;
> + };
> +
> + vdev0buffer: vdev0buffer@10042000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10042000 0x4000>;
> + no-map;
> + };
> +
> + gpu_reserved: gpu@f8000000 {
> + reg = <0xf8000000 0x8000000>;
> + no-map;
> + };
> + };
> +
> + sound {
> + compatible = "audio-graph-card";
> + label = "STM32MP1-PHYCORE";
> + routing =
> + "Playback", "MCLK", /* Set a route between "MCLK" and "playback" widgets */
> + "Capture", "MCLK";
> + dais = <&sai2b_port>,
> + <&sai2a_port>;
> + };
> +
> + regulator_vin: regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vin";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +};
> +
> +ðernet0 {
> + pinctrl-0 = <ðernet0_rgmii_pins_d>;
> + pinctrl-1 = <ðernet0_rgmii_sleep_pins_d>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rgmii-id";
> + max-speed = <1000>;
> + phy-handle = <&phy0>;
> + st,eth-clk-sel;
> + clock-names = "stmmaceth",
> + "mac-clk-tx",
> + "mac-clk-rx",
> + "eth-ck",
> + "syscfg-clk",
> + "ethstp";
> + clocks = <&rcc ETHMAC>,
> + <&rcc ETHTX>,
> + <&rcc ETHRX>,
> + <&rcc ETHCK_K>,
> + <&rcc SYSCFG>,
> + <&rcc ETHSTP>;
> + status = "okay";
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> +
> + phy0: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + interrupt-parent = <&gpiog>;
> + interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,min-output-impedance;
> + enet-phy-lane-no-swap;
> + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> + };
> + };
> +};
> +
> +&gpu {
> + contiguous-area = <&gpu_reserved>;
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c1_pins_b>;
> + pinctrl-1 = <&i2c1_sleep_pins_b>;
> + i2c-scl-rising-time-ns = <100>;
> + i2c-scl-falling-time-ns = <7>;
> + status = "okay";
> +
> + codec@18 {
> + compatible = "ti,tlv320aic3007";
> + reg = <0x18>;
> + #sound-dai-cells = <0>;
> +
> + ai3x-micbias-vg = <2>;
> +
> + AVDD-supply = <&v3v3>;
> + IOVDD-supply = <&v3v3>;
> + DRVDD-supply = <&v3v3>;
> + DVDD-supply = <&v1v8_audio>;
> +
> + clocks = <&sai2b>;
> + clock-names = "MCLK";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + tlv320_tx_endpoint: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&sai2b_endpoint>;
> + frame-master;
> + bitclock-master;
> + };
> +
> + tlv320_rx_endpoint: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&sai2a_endpoint>;
> + frame-master;
> + bitclock-master;
> + };
> + };
> + };
> +
> + touch@44 {
> + compatible = "st,stmpe811";
> + reg = <0x44>;
> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpioi>;
> + vio-supply = <&v3v3>;
> + vcc-supply = <&v3v3>;
> +
> + touchscreen {
> + compatible = "st,stmpe-ts";
> + st,sample-time = <4>;
> + st,mod-12b = <1>;
> + st,ref-sel = <0>;
> + st,adc-freq = <1>;
> + st,ave-ctrl = <1>;
> + st,touch-det-delay = <2>;
> + st,settling = <2>;
> + st,fraction-z = <7>;
> + st,i-drive = <1>;
> + };
> + };
> +
> + leds@62 {
> + compatible = "nxp,pca9533";
> + reg = <0x62>;
> +
> + led-0 {
> + color = <LED_COLOR_ID_RED>;
> + function = LED_FUNCTION_POWER;
> + type = <PCA9532_TYPE_LED>;
> + };
> +
> + led-1 {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_POWER;
> + type = <PCA9532_TYPE_LED>;
> + };
> +
> + led-2 {
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_HEARTBEAT;
> + type = <PCA9532_TYPE_LED>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c4_pins_a>;
> + pinctrl-1 = <&i2c4_sleep_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> +
> + pmic@33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> + buck1-supply = <®ulator_vin>;
> + buck2-supply = <®ulator_vin>;
> + buck3-supply = <®ulator_vin>;
> + buck4-supply = <®ulator_vin>;
> + ldo1-supply = <&v3v3>;
> + ldo2-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo4-supply = <®ulator_vin>;
> + ldo5-supply = <&v3v3>;
> + ldo6-supply = <&v3v3>;
> + vref_ddr-supply = <®ulator_vin>;
> + boost-supply = <®ulator_vin>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + st,mask-reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + v1v8_audio: ldo1 {
> + regulator-name = "v1v8_audio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO1 0>;
> +
> + };
> +
> + vdd_eth_2v5: ldo2 {
> + regulator-name = "dd_eth_2v5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO2 0>;
> +
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <750000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + interrupts = <IT_CURLIM_LDO4 0>;
> + };
> +
> + vdda: ldo5 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + regulator-boot-on;
> + };
> +
> + vdd_eth_1v0: ldo6 {
> + regulator-name = "vdd_eth_1v0";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO6 0>;
> +
> + };
> +
> + vref_ddr: vref-ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + regulator-active-discharge = <1>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + regulator-active-discharge = <1>;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>,
> + <IT_PONKEY_R 0>;
> + interrupt-names = "onkey-falling",
> + "onkey-rising";
> + power-off-time-sec = <10>;
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + };
> + };
> +
> + i2c4_eeprom: eeprom@50 {
> + compatible = "microchip,24c32",
> + "atmel,24c32";
> + reg = <0x50>;
> + };
> +
> + i2c4_rtc: rtc@52 {
> + compatible = "microcrystal,rv3028";
> + reg = <0x52>;
> + };
> +};
> +
> +&ipcc {
> + status = "okay";
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&m_can2 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&m_can2_pins_a>;
> + pinctrl-1 = <&m_can2_sleep_pins_a>;
> + status = "okay";
> +};
> +
> +&m4_rproc {
> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> + <&vdev0vring1>, <&vdev0buffer>;
> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
> + mbox-names = "vq0", "vq1", "shutdown", "detach";
> + interrupt-parent = <&exti>;
> + interrupts = <68 1>;
> + status = "okay";
> +};
> +
> +&pwr_regulators {
> + vdd-supply = <&vdd>;
> + vdd_3v3_usbfs-supply = <&vdd_usb>;
> +};
> +
> +&qspi {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
> + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
> + status = "okay";
> +
> + flash0: flash@0 {
> + compatible = "winbond,w25q128", "jedec,spi-nor";
> + reg = <0>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <50000000>;
> + m25p,fast-read;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&sai2 {
> + clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
> + clock-names = "pclk", "x8k", "x11k";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sai2a_pins_b>, <&sai2b_pins_d>;
> + pinctrl-1 = <&sai2a_sleep_pins_b>, <&sai2b_sleep_pins_d>;
> + status = "okay";
> +};
> +
> +&sai2a {
> + dma-names = "rx";
> + st,sync = <&sai2b 2>;
> + clocks = <&rcc SAI2_K>, <&sai2b>;
> + clock-names = "sai_ck", "MCLK";
> + #clock-cells = <0>;
> +
> + sai2a_port: port {
> + sai2a_endpoint: endpoint {
> + remote-endpoint = <&tlv320_rx_endpoint>;
> + format = "i2s";
> + mclk-fs = <256>;
> + dai-tdm-slot-num = <2>;
> + dai-tdm-slot-width = <16>;
> + };
> + };
> +};
> +
> +&sai2b {
> + dma-names = "tx";
> + #clock-cells = <0>;
> +
> + sai2b_port: port {
> + sai2b_endpoint: endpoint {
> + remote-endpoint = <&tlv320_tx_endpoint>;
> + format = "i2s";
> + mclk-fs = <256>;
> + dai-tdm-slot-num = <2>;
> + dai-tdm-slot-width = <16>;
> + };
> + };
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_b>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_b>;
> + cd-gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_e>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_e>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_e>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <8>;
> + vmmc-supply = <&v3v3>;
> + vqmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> +};
> +
> +&spi1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi1_pins_a>;
> + pinctrl-1 = <&spi1_sleep_pins_a>;
> + cs-gpios = <&gpioz 3 0>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default", "sleep", "idle";
> + pinctrl-0 = <&uart4_pins_a>;
> + pinctrl-1 = <&uart4_sleep_pins_a>;
> + pinctrl-2 = <&uart4_idle_pins_a>;
> + pinctrl-3 = <&uart4_pins_a>;
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + status = "okay";
> +};
> +
> +&usart1 {
> + pinctrl-names = "default", "sleep", "idle";
> + pinctrl-0 = <&usart1_pins_b &usart1_pins_a>;
> + pinctrl-1 = <&usart1_sleep_pins_b &usart1_sleep_pins_a>;
> + pinctrl-2 = <&usart1_idle_pins_b &usart1_idle_pins_a>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&usart3 {
> + pinctrl-names = "default", "sleep", "idle";
> + pinctrl-0 = <&usart3_pins_a>;
> + pinctrl-1 = <&usart3_sleep_pins_a>;
> + pinctrl-2 = <&usart3_idle_pins_a>;
> + status = "okay";
> +};
> +
> +&usbh_ehci {
> + phys = <&usbphyc_port0>;
> + phy-names = "usb";
> + status = "okay";
> +};
> +
> +&usbh_ohci {
> + phys = <&usbphyc_port0>;
> + phy-names = "usb";
> + status = "okay";
> +};
> +
> +&usbotg_hs {
> + phys = <&usbphyc_port1 0>;
> + phy-names = "usb2-phy";
> + vbus-supply = <&vbus_otg>;
> + status = "okay";
> +};
> +
> +&usbphyc {
> + status = "okay";
> +};
> +
> +&usbphyc_port0 {
> + phy-supply = <&vdd_usb>;
> + vbus-supply = <&vbus_sw>;
> +};
> +
> +&usbphyc_port1 {
> + phy-supply = <&vdd_usb>;
> +};
next prev parent reply other threads:[~2023-03-20 17:43 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-20 13:27 [PATCH v5 00/10] ARM: stm32: add support for Phycore STM32MP1 Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 01/10] ARM: dts: stm32: Add alternate pinmux for ethernet Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 02/10] ARM: dts: stm32: Add alternate pinmux for sai2b Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 03/10] ARM: dts: stm32: Add new pinmux for sdmmc1_b4 Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 04/10] ARM: dts: stm32: Add new pinmux for sdmmc2_d47 Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 05/10] ARM: dts: stm32: Add pinmux for USART1 pins Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 06/10] ARM: dts: stm32: Add idle/sleep pinmux for USART3 Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 07/10] ARM: dts: stm32: Add sleep pinmux for SPI1 pins_a Steffen Trumtrar
2023-03-20 13:27 ` [PATCH v5 08/10] dt-bindings: arm: stm32: Add Phytec STM32MP1 board Steffen Trumtrar
2023-03-20 16:45 ` Krzysztof Kozlowski
2023-03-20 13:27 ` [PATCH v5 09/10] ARM: dts: stm32: add STM32MP1-based Phytec SoM Steffen Trumtrar
2023-03-20 17:37 ` Alexandre TORGUE [this message]
2023-03-21 7:14 ` Steffen Trumtrar
2023-03-28 7:51 ` Alexandre TORGUE
2023-03-20 13:27 ` [PATCH v5 10/10] ARM: dts: stm32: add STM32MP1-based Phytec board Steffen Trumtrar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a37db3a8-a3e6-8755-2b7c-c33a1fdca469@foss.st.com \
--to=alexandre.torgue@foss.st.com \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=s.trumtrar@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).