[PATCH v4 0/2] Add basic support for Mediatek MT2712 SoC

[PATCH v4 0/2] Add basic support for Mediatek MT2712 SoC

[YT Shen]

MT2712 is a SoC based on 64bit ARMv8 architecture.
MT2712 share many HW IP with MT8173.  This patchset was tested on MT2712 evaluation board, and boot to shell ok.

This series contains document bindings, device tree including interrupt and uart.

Changes compared to v3:
- use two uart clocks refer to the bindings

Changes compared to v2:
- remove alias from serial1 to serial5
- remove initrd-start and initrd-end
- change GIC_CPU_MASK_SIMPLE(6) to GIC_CPU_MASK_RAW(0x13)
- change gic-400 reg range

Changes compared to v1:
- change subject prefix for bindings
- change device tree license to SPDX tag.
- change bootargs parameter to DT usage.
- change intpol-controller to interrupt-controller

YT Shen (2):
  dt-bindings: arm: Add bindings for Mediatek MT2712 SoC Platform
  arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and
    Makefile

 Documentation/devicetree/bindings/arm/mediatek.txt |   4 +
 .../interrupt-controller/mediatek,sysirq.txt       |   1 +
 .../devicetree/bindings/serial/mtk-uart.txt        |   1 +
 arch/arm64/boot/dts/mediatek/Makefile              |   1 +
 arch/arm64/boot/dts/mediatek/mt2712-evb.dts        |  32 ++++
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi          | 172 +++++++++++++++++++++
 6 files changed, 211 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi

-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 1/2] dt-bindings: arm: Add bindings for Mediatek MT2712 SoC Platform

[YT Shen]

This adds dt-binding documentation for Mediatek MT2712.
Only include very basic items: cpu, gic and uart.

Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/mediatek.txt                    | 4 ++++
 .../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt      | 1 +
 Documentation/devicetree/bindings/serial/mtk-uart.txt                 | 1 +
 3 files changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt
index c860b24..3161651 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@@ -7,6 +7,7 @@ Required root node property:
 
 compatible: Must contain one of
    "mediatek,mt2701"
+   "mediatek,mt2712"
    "mediatek,mt6580"
    "mediatek,mt6589"
    "mediatek,mt6592"
@@ -23,6 +24,9 @@ Supported boards:
 - Evaluation board for MT2701:
     Required root node properties:
       - compatible = "mediatek,mt2701-evb", "mediatek,mt2701";
+- Evaluation board for MT2712:
+    Required root node properties:
+      - compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
 - Evaluation board for MT6580:
     Required root node properties:
       - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580";
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index a89c03b..653adb5 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -16,6 +16,7 @@ Required properties:
 	"mediatek,mt6580-sysirq"
 	"mediatek,mt6577-sysirq"
 	"mediatek,mt2701-sysirq"
+	"mediatek,mt2712-sysirq"
 - interrupt-controller : Identifies the node as an interrupt controller
 - #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
 - interrupt-parent: phandle of irq parent for sysirq. The parent must
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
index 0015c72..5f88e0d 100644
--- a/Documentation/devicetree/bindings/serial/mtk-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -3,6 +3,7 @@
 Required properties:
 - compatible should contain:
   * "mediatek,mt2701-uart" for MT2701 compatible UARTS
+  * "mediatek,mt2712-uart" for MT2712 compatible UARTS
   * "mediatek,mt6580-uart" for MT6580 compatible UARTS
   * "mediatek,mt6582-uart" for MT6582 compatible UARTS
   * "mediatek,mt6589-uart" for MT6589 compatible UARTS
-- 
1.9.1

[PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[YT Shen]

This adds basic chip support for Mediatek 2712

Signed-off-by: YT Shen <yt.shen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
 arch/arm64/boot/dts/mediatek/Makefile       |   1 +
 arch/arm64/boot/dts/mediatek/mt2712-evb.dts |  32 ++++++
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi   | 172 ++++++++++++++++++++++++++++
 3 files changed, 205 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 9fbfd32..fcc0604 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -1,3 +1,4 @@
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
new file mode 100644
index 0000000..8c804df
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
@@ -0,0 +1,32 @@
+/*
+ * Copyright (c) 2017 MediaTek Inc.
+ * Author: YT Shen <yt.shen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+#include "mt2712e.dtsi"
+
+/ {
+	model = "MediaTek MT2712 evaluation board";
+	compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
new file mode 100644
index 0000000..461ee0f
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -0,0 +1,172 @@
+/*
+ * Copyright (c) 2017 MediaTek Inc.
+ * Author: YT Shen <yt.shen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "mediatek,mt2712";
+	interrupt-parent = <&sysirq>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu2>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x001>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x200>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	uart_clk: dummy26m {
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+		#clock-cells = <0>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13
+			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		uart5: serial@1000f000 {
+			compatible = "mediatek,mt2712-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x1000f000 0 0x400>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		sysirq: interrupt-controller@10220a80 {
+			compatible = "mediatek,mt2712-sysirq",
+				     "mediatek,mt6577-sysirq";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			reg = <0 0x10220a80 0 0x40>;
+		};
+
+		gic: interrupt-controller@10510000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x10510000 0 0x10000>,
+			      <0 0x10520000 0 0x20000>,
+			      <0 0x10540000 0 0x20000>,
+			      <0 0x10560000 0 0x20000>;
+			interrupts = <GIC_PPI 9
+				(GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt2712-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x400>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt2712-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x400>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt2712-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x400>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart3: serial@11005000 {
+			compatible = "mediatek,mt2712-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11005000 0 0x400>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart4: serial@11019000 {
+			compatible = "mediatek,mt2712-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11019000 0 0x400>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+	};
+};
+
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[Matthias Brugger]

On 06/22/2017 11:32 AM, YT Shen wrote:
> This adds basic chip support for Mediatek 2712
> 
> Signed-off-by: YT Shen <yt.shen@mediatek.com>
> ---
>   arch/arm64/boot/dts/mediatek/Makefile       |   1 +
>   arch/arm64/boot/dts/mediatek/mt2712-evb.dts |  32 ++++++
>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi   | 172 ++++++++++++++++++++++++++++
>   3 files changed, 205 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 9fbfd32..fcc0604 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -1,3 +1,4 @@
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> new file mode 100644
> index 0000000..8c804df
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> @@ -0,0 +1,32 @@
> +/*
> + * Copyright (c) 2017 MediaTek Inc.
> + * Author: YT Shen <yt.shen@mediatek.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> + */
> +
> +/dts-v1/;
> +#include "mt2712e.dtsi"
> +
> +/ {
> +	model = "MediaTek MT2712 evaluation board";
> +	compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	memory@40000000 {
> +		device_type = "memory";
> +		reg = <0 0x40000000 0 0x80000000>;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:921600n8";
> +	};
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> new file mode 100644
> index 0000000..461ee0f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> @@ -0,0 +1,172 @@
> +/*
> + * Copyright (c) 2017 MediaTek Inc.
> + * Author: YT Shen <yt.shen@mediatek.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> +	compatible = "mediatek,mt2712";
> +	interrupt-parent = <&sysirq>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&cpu0>;
> +				};
> +				core1 {
> +					cpu = <&cpu1>;
> +				};
> +			};
> +
> +			cluster1 {
> +				core0 {
> +					cpu = <&cpu2>;
> +				};
> +			};
> +		};
> +
> +		cpu0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a35";
> +			reg = <0x000>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a35";
> +			reg = <0x001>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu2: cpu@200 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a72";
> +			reg = <0x200>;
> +			enable-method = "psci";
> +		};
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2";
> +		method = "smc";
> +	};
> +
> +	uart_clk: dummy26m {
> +		compatible = "fixed-clock";
> +		clock-frequency = <26000000>;
> +		#clock-cells = <0>;
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_PPI 13
> +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 14
> +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 11
> +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 10
> +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +
> +	soc {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		compatible = "simple-bus";
> +		ranges;
> +
> +		uart5: serial@1000f000 {
> +			compatible = "mediatek,mt2712-uart",
> +				     "mediatek,mt6577-uart";
> +			reg = <0 0x1000f000 0 0x400>;
> +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&uart_clk>, <&uart_clk>;
> +			clock-names = "baud", "bus";
> +			status = "disabled";
> +		};

So baud and bus clock are both 26 MHz?

Regards,
Matthias

Re: [PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[YT Shen]

On Tue, 2017-07-18 at 18:29 +0200, Matthias Brugger wrote:
> 
> On 06/22/2017 11:32 AM, YT Shen wrote:
> > This adds basic chip support for Mediatek 2712
> > 
> > Signed-off-by: YT Shen <yt.shen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> > ---
> >   arch/arm64/boot/dts/mediatek/Makefile       |   1 +
> >   arch/arm64/boot/dts/mediatek/mt2712-evb.dts |  32 ++++++
> >   arch/arm64/boot/dts/mediatek/mt2712e.dtsi   | 172 ++++++++++++++++++++++++++++
> >   3 files changed, 205 insertions(+)
> >   create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> >   create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > 
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > index 9fbfd32..fcc0604 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -1,3 +1,4 @@
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
> >   dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
> >   dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
> >   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> > diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > new file mode 100644
> > index 0000000..8c804df
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > @@ -0,0 +1,32 @@
> > +/*
> > + * Copyright (c) 2017 MediaTek Inc.
> > + * Author: YT Shen <yt.shen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt2712e.dtsi"
> > +
> > +/ {
> > +	model = "MediaTek MT2712 evaluation board";
> > +	compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
> > +
> > +	aliases {
> > +		serial0 = &uart0;
> > +	};
> > +
> > +	memory@40000000 {
> > +		device_type = "memory";
> > +		reg = <0 0x40000000 0 0x80000000>;
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:921600n8";
> > +	};
> > +};
> > +
> > +&uart0 {
> > +	status = "okay";
> > +};
> > +
> > diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > new file mode 100644
> > index 0000000..461ee0f
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > @@ -0,0 +1,172 @@
> > +/*
> > + * Copyright (c) 2017 MediaTek Inc.
> > + * Author: YT Shen <yt.shen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/ {
> > +	compatible = "mediatek,mt2712";
> > +	interrupt-parent = <&sysirq>;
> > +	#address-cells = <2>;
> > +	#size-cells = <2>;
> > +
> > +	cpus {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		cpu-map {
> > +			cluster0 {
> > +				core0 {
> > +					cpu = <&cpu0>;
> > +				};
> > +				core1 {
> > +					cpu = <&cpu1>;
> > +				};
> > +			};
> > +
> > +			cluster1 {
> > +				core0 {
> > +					cpu = <&cpu2>;
> > +				};
> > +			};
> > +		};
> > +
> > +		cpu0: cpu@0 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a35";
> > +			reg = <0x000>;
> > +		};
> > +
> > +		cpu1: cpu@1 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a35";
> > +			reg = <0x001>;
> > +			enable-method = "psci";
> > +		};
> > +
> > +		cpu2: cpu@200 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a72";
> > +			reg = <0x200>;
> > +			enable-method = "psci";
> > +		};
> > +	};
> > +
> > +	psci {
> > +		compatible = "arm,psci-0.2";
> > +		method = "smc";
> > +	};
> > +
> > +	uart_clk: dummy26m {
> > +		compatible = "fixed-clock";
> > +		clock-frequency = <26000000>;
> > +		#clock-cells = <0>;
> > +	};
> > +
> > +	timer {
> > +		compatible = "arm,armv8-timer";
> > +		interrupt-parent = <&gic>;
> > +		interrupts = <GIC_PPI 13
> > +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 14
> > +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 11
> > +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 10
> > +			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
> > +	};
> > +
> > +	soc {
> > +		#address-cells = <2>;
> > +		#size-cells = <2>;
> > +		compatible = "simple-bus";
> > +		ranges;
> > +
> > +		uart5: serial@1000f000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x1000f000 0 0x400>;
> > +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>, <&uart_clk>;
> > +			clock-names = "baud", "bus";
> > +			status = "disabled";
> > +		};
> 
> So baud and bus clock are both 26 MHz?
We didn't have CCF clock support in this series.
After we have clock source support, we could use the correct clocks to
the UARTs and drop the 26MHz fixed rate UART clock.

The bus clock is 26MHz.  The baud clock could be from another clock
source, using the same 26MHz fixed clock works also.


[1] https://patchwork.kernel.org/patch/9670877/
[2] https://patchwork.kernel.org/patch/6436021/

> Regards,
> Matthias


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[Matthias Brugger]

On 07/19/2017 08:48 AM, YT Shen wrote:
> On Tue, 2017-07-18 at 18:29 +0200, Matthias Brugger wrote:
>>
>> On 06/22/2017 11:32 AM, YT Shen wrote:
>>> This adds basic chip support for Mediatek 2712

[...]

>>> +
>>> +	uart_clk: dummy26m {
>>> +		compatible = "fixed-clock";
>>> +		clock-frequency = <26000000>;
>>> +		#clock-cells = <0>;
>>> +	};
>>> +

[...]

>>> +
>>> +	soc {
>>> +		#address-cells = <2>;
>>> +		#size-cells = <2>;
>>> +		compatible = "simple-bus";
>>> +		ranges;
>>> +
>>> +		uart5: serial@1000f000 {
>>> +			compatible = "mediatek,mt2712-uart",
>>> +				     "mediatek,mt6577-uart";
>>> +			reg = <0 0x1000f000 0 0x400>;
>>> +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
>>> +			clocks = <&uart_clk>, <&uart_clk>;
>>> +			clock-names = "baud", "bus";
>>> +			status = "disabled";
>>> +		};
>>
>> So baud and bus clock are both 26 MHz?
> We didn't have CCF clock support in this series.
> After we have clock source support, we could use the correct clocks to
> the UARTs and drop the 26MHz fixed rate UART clock.
> 
> The bus clock is 26MHz.  The baud clock could be from another clock
> source, using the same 26MHz fixed clock works also.
> 
> 
> [1] https://patchwork.kernel.org/patch/9670877/
> [2] https://patchwork.kernel.org/patch/6436021/
> 

Yes, just using one 26 MHz clock works, but it uses an deprecated 
binding, so we should not do this, as through copying from the source of 
other SoCs we will keep it alive forever. Anyway that's not your case, 
as you defined the two clocks.

The device tree should reflect the HW, that's why I asked for the clock 
frequency of both clocks. I searched the git history and it was never 
done right before. So you could be the first :)

Thanks,
Matthias

Re: [PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[YT Shen]

On Wed, 2017-07-19 at 11:26 +0200, Matthias Brugger wrote:
> 
> On 07/19/2017 08:48 AM, YT Shen wrote:
> > On Tue, 2017-07-18 at 18:29 +0200, Matthias Brugger wrote:
> >>
> >> On 06/22/2017 11:32 AM, YT Shen wrote:
> >>> This adds basic chip support for Mediatek 2712
> 
> [...]
> 
> >>> +
> >>> +	uart_clk: dummy26m {
> >>> +		compatible = "fixed-clock";
> >>> +		clock-frequency = <26000000>;
> >>> +		#clock-cells = <0>;
> >>> +	};
> >>> +
> 
> [...]
> 
> >>> +
> >>> +	soc {
> >>> +		#address-cells = <2>;
> >>> +		#size-cells = <2>;
> >>> +		compatible = "simple-bus";
> >>> +		ranges;
> >>> +
> >>> +		uart5: serial@1000f000 {
> >>> +			compatible = "mediatek,mt2712-uart",
> >>> +				     "mediatek,mt6577-uart";
> >>> +			reg = <0 0x1000f000 0 0x400>;
> >>> +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> >>> +			clocks = <&uart_clk>, <&uart_clk>;
> >>> +			clock-names = "baud", "bus";
> >>> +			status = "disabled";
> >>> +		};
> >>
> >> So baud and bus clock are both 26 MHz?
> > We didn't have CCF clock support in this series.
> > After we have clock source support, we could use the correct clocks to
> > the UARTs and drop the 26MHz fixed rate UART clock.
> > 
> > The bus clock is 26MHz.  The baud clock could be from another clock
> > source, using the same 26MHz fixed clock works also.
> > 
> > 
> > [1] https://patchwork.kernel.org/patch/9670877/
> > [2] https://patchwork.kernel.org/patch/6436021/
> > 
> 
> Yes, just using one 26 MHz clock works, but it uses an deprecated 
> binding, so we should not do this, as through copying from the source of 
> other SoCs we will keep it alive forever. Anyway that's not your case, 
> as you defined the two clocks.
> 
> The device tree should reflect the HW, that's why I asked for the clock 
> frequency of both clocks. I searched the git history and it was never 
> done right before. So you could be the first :)
> 
> Thanks,
> Matthias
Ok, I want to make it clear.  The following example

        baud_clk: dummy26m {
                compatible = "fixed-clock";
                clock-frequency = <26000000>;
                #clock-cells = <0>;
        };

        sys_clk: dummyclk {
                compatible = "fixed-clock";
                clock-frequency = <26000000>;
                #clock-cells = <0>;
        };

	uart0: serial@11002000 {
[...]
                clocks = <&baud_clk>, <&sys_clk>;
[...]
	}

Do you think it is clear to reflect the HW that the baud clock and sys
clock can be different source or we need to choose another frequency?
Thanks.

yt.shen

Re: [PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[Matthias Brugger]

On 07/21/2017 08:32 AM, YT Shen wrote:
> On Wed, 2017-07-19 at 11:26 +0200, Matthias Brugger wrote:
>>
>> On 07/19/2017 08:48 AM, YT Shen wrote:
>>> On Tue, 2017-07-18 at 18:29 +0200, Matthias Brugger wrote:
>>>>
>>>> On 06/22/2017 11:32 AM, YT Shen wrote:
>>>>> This adds basic chip support for Mediatek 2712
>>
>> [...]
>>
>>>>> +
>>>>> +	uart_clk: dummy26m {
>>>>> +		compatible = "fixed-clock";
>>>>> +		clock-frequency = <26000000>;
>>>>> +		#clock-cells = <0>;
>>>>> +	};
>>>>> +
>>
>> [...]
>>
>>>>> +
>>>>> +	soc {
>>>>> +		#address-cells = <2>;
>>>>> +		#size-cells = <2>;
>>>>> +		compatible = "simple-bus";
>>>>> +		ranges;
>>>>> +
>>>>> +		uart5: serial@1000f000 {
>>>>> +			compatible = "mediatek,mt2712-uart",
>>>>> +				     "mediatek,mt6577-uart";
>>>>> +			reg = <0 0x1000f000 0 0x400>;
>>>>> +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
>>>>> +			clocks = <&uart_clk>, <&uart_clk>;
>>>>> +			clock-names = "baud", "bus";
>>>>> +			status = "disabled";
>>>>> +		};
>>>>
>>>> So baud and bus clock are both 26 MHz?
>>> We didn't have CCF clock support in this series.
>>> After we have clock source support, we could use the correct clocks to
>>> the UARTs and drop the 26MHz fixed rate UART clock.
>>>
>>> The bus clock is 26MHz.  The baud clock could be from another clock
>>> source, using the same 26MHz fixed clock works also.
>>>
>>>
>>> [1] https://patchwork.kernel.org/patch/9670877/
>>> [2] https://patchwork.kernel.org/patch/6436021/
>>>
>>
>> Yes, just using one 26 MHz clock works, but it uses an deprecated
>> binding, so we should not do this, as through copying from the source of
>> other SoCs we will keep it alive forever. Anyway that's not your case,
>> as you defined the two clocks.
>>
>> The device tree should reflect the HW, that's why I asked for the clock
>> frequency of both clocks. I searched the git history and it was never
>> done right before. So you could be the first :)
>>
>> Thanks,
>> Matthias
> Ok, I want to make it clear.  The following example
> 
>          baud_clk: dummy26m {
>                  compatible = "fixed-clock";
>                  clock-frequency = <26000000>;
>                  #clock-cells = <0>;
>          };
> 
>          sys_clk: dummyclk {
>                  compatible = "fixed-clock";
>                  clock-frequency = <26000000>;
>                  #clock-cells = <0>;
>          };
> 
> 	uart0: serial@11002000 {
> [...]
>                  clocks = <&baud_clk>, <&sys_clk>;
> [...]
> 	}
> 
> Do you think it is clear to reflect the HW that the baud clock and sys
> clock can be different source or we need to choose another frequency?
> Thanks.
> 

Best would be to choose the frequency you expect from both clocks. E.g. 
the frequency set by the bootloader. If the clock is the same, then we 
can leave the patch as-is.

Thanks,
Matthias
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 0/2] Add basic support for Mediatek MT2712 SoC

[YT Shen]

Hi Matthias,

Just a gentle ping.
Should I rebase to 4.13-rc1 and send v5?

Thanks
yt.shen

On Thu, 2017-06-22 at 17:32 +0800, YT Shen wrote:
> MT2712 is a SoC based on 64bit ARMv8 architecture.
> MT2712 share many HW IP with MT8173.  This patchset was tested on MT2712 evaluation board, and boot to shell ok.
> 
> This series contains document bindings, device tree including interrupt and uart.
> 
> Changes compared to v3:
> - use two uart clocks refer to the bindings
> 
> Changes compared to v2:
> - remove alias from serial1 to serial5
> - remove initrd-start and initrd-end
> - change GIC_CPU_MASK_SIMPLE(6) to GIC_CPU_MASK_RAW(0x13)
> - change gic-400 reg range
> 
> Changes compared to v1:
> - change subject prefix for bindings
> - change device tree license to SPDX tag.
> - change bootargs parameter to DT usage.
> - change intpol-controller to interrupt-controller
> 
> YT Shen (2):
>   dt-bindings: arm: Add bindings for Mediatek MT2712 SoC Platform
>   arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and
>     Makefile
> 
>  Documentation/devicetree/bindings/arm/mediatek.txt |   4 +
>  .../interrupt-controller/mediatek,sysirq.txt       |   1 +
>  .../devicetree/bindings/serial/mtk-uart.txt        |   1 +
>  arch/arm64/boot/dts/mediatek/Makefile              |   1 +
>  arch/arm64/boot/dts/mediatek/mt2712-evb.dts        |  32 ++++
>  arch/arm64/boot/dts/mediatek/mt2712e.dtsi          | 172 +++++++++++++++++++++
>  6 files changed, 211 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> 


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html