From: Nicolas Ferre <nicolas.ferre@microchip.com>
To: Claudiu Beznea <claudiu.beznea@microchip.com>,
<alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <robh+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 1/2] ARM: dts: at91: add pinctrl-{names, 0} for all gpios
Date: Tue, 27 Jul 2021 10:53:38 +0200 [thread overview]
Message-ID: <a7af9524-db26-36f8-8101-8c431c7d25d6@microchip.com> (raw)
In-Reply-To: <20210727074006.1609989-1-claudiu.beznea@microchip.com>
On 27/07/2021 at 09:40, Claudiu Beznea wrote:
> Add pinctrl-names and pinctrl-0 properties on controllers that claims to
> use pins to avoid failures due to
> commit 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges")
> and also to avoid using pins that may be claimed my other IPs.
>
> Fixes: b7c2b6157079 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
> Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
> Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained
> board")
> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Queued in at91-dt for 5.15 with additional tag:
Cc: <stable@vger.kernel.org> # v5.7+
Best regards,
Nicolas
> ---
> arch/arm/boot/dts/at91-sam9x60ek.dts | 16 +++++++++++-
> arch/arm/boot/dts/at91-sama5d3_xplained.dts | 29 +++++++++++++++++++++
> arch/arm/boot/dts/at91-sama5d4_xplained.dts | 19 ++++++++++++++
> 3 files changed, 63 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
> index edca66c232c1..ebbc9b23aef1 100644
> --- a/arch/arm/boot/dts/at91-sam9x60ek.dts
> +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
> @@ -92,6 +92,8 @@ sw1 {
>
> leds {
> compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> status = "okay"; /* Conflict with pwm0. */
>
> red {
> @@ -537,6 +539,10 @@ AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_H
> AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA19 DAT2 periph A with pullup */
> AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA20 DAT3 periph A with pullup */
> };
> + pinctrl_sdmmc0_cd: sdmmc0_cd {
> + atmel,pins =
> + <AT91_PIOA 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> };
>
> sdmmc1 {
> @@ -569,6 +575,14 @@ pinctrl_usb_default: usb_default {
> AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> };
> };
> +
> + leds {
> + pinctrl_gpio_leds: gpio_leds {
> + atmel,pins = <AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOB 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> }; /* pinctrl */
>
> &pwm0 {
> @@ -580,7 +594,7 @@ &pwm0 {
> &sdmmc0 {
> bus-width = <4>;
> pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_sdmmc0_default>;
> + pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
> status = "okay";
> cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
> disable-wp;
> diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
> index 9c55a921263b..cc55d1684322 100644
> --- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
> +++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
> @@ -57,6 +57,8 @@ slot@0 {
> };
>
> spi0: spi@f0004000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi0_cs>;
> cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
> status = "okay";
> };
> @@ -169,6 +171,8 @@ slot@0 {
> };
>
> spi1: spi@f8008000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_cs>;
> cs-gpios = <&pioC 25 0>;
> status = "okay";
> };
> @@ -248,6 +252,26 @@ pinctrl_usb_default: usb_default {
> <AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> };
> +
> + pinctrl_gpio_leds: gpio_leds_default {
> + atmel,pins =
> + <AT91_PIOE 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_spi0_cs: spi0_cs_default {
> + atmel,pins =
> + <AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_spi1_cs: spi1_cs_default {
> + atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_vcc_mmc0_reg_gpio: vcc_mmc0_reg_gpio_default {
> + atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> };
> };
> };
> @@ -339,6 +363,8 @@ rootfs@800000 {
>
> vcc_mmc0_reg: fixedregulator_mmc0 {
> compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
> gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
> regulator-name = "mmc0-card-supply";
> regulator-min-microvolt = <3300000>;
> @@ -362,6 +388,9 @@ bp3 {
>
> leds {
> compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> + status = "okay";
>
> d2 {
> label = "d2";
> diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
> index 046796c5b9b0..541779af049f 100644
> --- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
> +++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
> @@ -80,6 +80,8 @@ usart4: serial@fc010000 {
> };
>
> spi1: spi@fc018000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi0_cs>;
> cs-gpios = <&pioB 21 0>;
> status = "okay";
> };
> @@ -137,6 +139,19 @@ pinctrl_macb0_phy_irq: macb0_phy_irq_0 {
> atmel,pins =
> <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> };
> + pinctrl_spi0_cs: spi0_cs_default {
> + atmel,pins =
> + <AT91_PIOB 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + pinctrl_gpio_leds: gpio_leds_default {
> + atmel,pins =
> + <AT91_PIOD 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOE 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + pinctrl_vcc_mmc1_reg: vcc_mmc1_reg {
> + atmel,pins =
> + <AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> };
> };
> };
> @@ -242,6 +257,8 @@ pb_user1 {
>
> leds {
> compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> status = "okay";
>
> d8 {
> @@ -268,6 +285,8 @@ vcc_3v3_reg: fixedregulator_3v3 {
>
> vcc_mmc1_reg: fixedregulator_mmc1 {
> compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_vcc_mmc1_reg>;
> gpio = <&pioE 4 GPIO_ACTIVE_LOW>;
> regulator-name = "VDD MCI1";
> regulator-min-microvolt = <3300000>;
>
--
Nicolas Ferre
prev parent reply other threads:[~2021-07-27 8:53 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-27 7:40 [PATCH 1/2] ARM: dts: at91: add pinctrl-{names, 0} for all gpios Claudiu Beznea
2021-07-27 7:40 ` [PATCH 2/2] ARM: dts: at91: add conflict note for d3 Claudiu Beznea
2021-07-27 8:54 ` Nicolas Ferre
2021-07-27 8:53 ` Nicolas Ferre [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a7af9524-db26-36f8-8101-8c431c7d25d6@microchip.com \
--to=nicolas.ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=claudiu.beznea@microchip.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).