Hi,

Some comments below.

On Fri 21 Feb 25, 17:17, Kuba Szczodrzyński wrote:
> The Allwinner D1s/T113 needs to use the combo D-PHY to enable LVDS
> output.
> 
> Enable LVDS support in the TCON and configure it using the PHY.
> 
> Signed-off-by: Kuba Szczodrzyński <kuba@szczodrzynski.pl>
> ---
>  drivers/gpu/drm/sun4i/sun4i_tcon.c | 28 ++++++++++++++++++++++++++++
>  1 file changed, 28 insertions(+)
> 
> diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
> index ccf335a61..58230a552 100644
> --- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
> +++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
> @@ -171,6 +171,30 @@ static void sun6i_tcon_setup_lvds_phy(struct sun4i_tcon *tcon,
>  			  SUN6I_TCON0_LVDS_ANA0_EN_DRVD(val));
>  }
>  
> +static void sun20i_tcon_setup_lvds_dphy(struct sun4i_tcon *tcon,
> +					const struct drm_encoder *encoder)
> +{
> +	union phy_configure_opts opts = { };
> +
> +	if (!tcon->quirks->has_combo_dphy || !tcon->dphy)
> +		return;
> +
> +	phy_init(tcon->dphy);
> +	phy_set_mode(tcon->dphy, PHY_MODE_LVDS);
> +	phy_configure(tcon->dphy, &opts);
> +	phy_power_on(tcon->dphy);

While the callback doesn't have any return code (and it probably should, feel
free to fix that), the return codes for the phy_ calls should be checked and
the function aborted early in case of error.

> +}
> +
> +static void sun20i_tcon_disable_lvds_dphy(struct sun4i_tcon *tcon,
> +					  const struct drm_encoder *encoder)
> +{
> +	if (!tcon->quirks->has_combo_dphy || !tcon->dphy)
> +		return;
> +
> +	phy_power_off(tcon->dphy);
> +	phy_exit(tcon->dphy);

Same comment here.

> +}
> +
>  static void sun4i_tcon_lvds_set_status(struct sun4i_tcon *tcon,
>  				       const struct drm_encoder *encoder,
>  				       bool enabled)
> @@ -1550,8 +1574,12 @@ static const struct sun4i_tcon_quirks sun9i_a80_tcon_tv_quirks = {
>  
>  static const struct sun4i_tcon_quirks sun20i_d1_lcd_quirks = {
>  	.has_channel_0		= true,
> +	.has_combo_dphy		= true,
> +	.supports_lvds		= true,
>  	.dclk_min_div		= 1,
>  	.set_mux		= sun8i_r40_tcon_tv_set_mux,
> +	.setup_lvds_phy		= sun20i_tcon_setup_lvds_dphy,
> +	.disable_lvds_phy	= sun20i_tcon_disable_lvds_dphy,
>  };
>  
>  /* sun4i_drv uses this list to check if a device node is a TCON */
> -- 
> 2.25.1
> 
> 

-- 
Paul Kocialkowski,

Independent contractor - sys-base - https://www.sys-base.io/
Free software developer - https://www.paulk.fr/

Expert in multimedia, graphics and embedded hardware support with Linux.