* [PATCH v4 1/2] dt-bindings: arm: fsl: Add Protonic PRT8ML
2025-10-14 13:09 [PATCH v4 0/2] Mainline Protonic PRT8ML board Jonas Rebmann
@ 2025-10-14 13:09 ` Jonas Rebmann
2025-10-14 13:09 ` [PATCH v4 2/2] arm64: dts: add Protonic PRT8ML board Jonas Rebmann
2025-10-27 6:06 ` [PATCH v4 0/2] Mainline " Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Jonas Rebmann @ 2025-10-14 13:09 UTC (permalink / raw)
To: Andrew Lunn, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Liam Girdwood, Mark Brown, Shengjiu Wang, Shawn Guo,
Sascha Hauer, Fabio Estevam, Pengutronix Kernel Team
Cc: Vladimir Oltean, netdev, devicetree, linux-kernel, linux-sound,
imx, linux-arm-kernel, Peng Fan, Jonas Rebmann
Add DT compatible string for Protonic PRT8ML board.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 00cdf490b062..b135f6360733 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1106,6 +1106,7 @@ properties:
- gateworks,imx8mp-gw75xx-2x # i.MX8MP Gateworks Board
- gateworks,imx8mp-gw82xx-2x # i.MX8MP Gateworks Board
- gocontroll,moduline-display # GOcontroll Moduline Display controller
+ - prt,prt8ml # Protonic PRT8ML
- skov,imx8mp-skov-basic # SKOV i.MX8MP baseboard without frontplate
- skov,imx8mp-skov-revb-hdmi # SKOV i.MX8MP climate control without panel
- skov,imx8mp-skov-revb-lt6 # SKOV i.MX8MP climate control with 7” panel
--
2.51.0.297.gca2559c1d6
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v4 2/2] arm64: dts: add Protonic PRT8ML board
2025-10-14 13:09 [PATCH v4 0/2] Mainline Protonic PRT8ML board Jonas Rebmann
2025-10-14 13:09 ` [PATCH v4 1/2] dt-bindings: arm: fsl: Add Protonic PRT8ML Jonas Rebmann
@ 2025-10-14 13:09 ` Jonas Rebmann
2025-10-27 6:06 ` [PATCH v4 0/2] Mainline " Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Jonas Rebmann @ 2025-10-14 13:09 UTC (permalink / raw)
To: Andrew Lunn, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Liam Girdwood, Mark Brown, Shengjiu Wang, Shawn Guo,
Sascha Hauer, Fabio Estevam, Pengutronix Kernel Team
Cc: Vladimir Oltean, netdev, devicetree, linux-kernel, linux-sound,
imx, linux-arm-kernel, Peng Fan, Jonas Rebmann, David Jander,
Lucas Stach, Oleksij Rempel
Add devicetree for the Protonic PRT8ML.
The board is similar to the Protonic PRT8MM but i.MX8MP based.
Some features have been removed as the drivers haven't been mainlined
yet or other issues where encountered:
- Stepper motors to be controlled using motion control subsystem
- MIPI/DSI to eDP USB alt-mode
- Onboard T1 ethernet (10BASE-T1L+PoDL, 100BASE-T1+PoDL, 1000BASE-T1)
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx8mp-prt8ml.dts | 504 ++++++++++++++++++++++++
2 files changed, 505 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 525ef180481d..0c9abfa8d23d 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -228,6 +228,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-nitrogen-smarc-universal-board.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
imx8mp-phyboard-pollux-rdk-no-eth-dtbs += imx8mp-phyboard-pollux-rdk.dtb imx8mp-phycore-no-eth.dtbo
dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk-no-eth.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-prt8ml.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-basic.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-prt8ml.dts b/arch/arm64/boot/dts/freescale/imx8mp-prt8ml.dts
new file mode 100644
index 000000000000..30616218017b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-prt8ml.dts
@@ -0,0 +1,504 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2020 Protonic Holland
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8mp.dtsi"
+
+/ {
+ model = "Protonic PRT8ML";
+ compatible = "prt,prt8ml", "fsl,imx8mp";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ pcie_refclk: pcie0-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ pcie_refclk_oe: pcie0-refclk-oe {
+ compatible = "gpio-gate-clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_refclk>;
+ clocks = <&pcie_refclk>;
+ #clock-cells = <0>;
+ enable-gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&fan53555>;
+};
+
+&A53_1 {
+ cpu-supply = <&fan53555>;
+};
+
+&A53_2 {
+ cpu-supply = <&fan53555>;
+};
+
+&A53_3 {
+ cpu-supply = <&fan53555>;
+};
+
+&a53_opp_table {
+ opp-1200000000 {
+ opp-microvolt = <900000>;
+ };
+
+ opp-1600000000 {
+ opp-microvolt = <980000>;
+ };
+
+ /* Power supply insuffient for 1.8 GHz */
+ /delete-node/ opp-1800000000;
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+
+ /* Disable DMA to meet performance requirements */
+ /delete-property/ dmas;
+ /delete-property/ dma-names;
+ status = "okay";
+
+ switch@0 {
+ compatible = "nxp,sja1105q";
+ reg = <0>;
+ reset-gpios = <&gpio_exp_1 4 GPIO_ACTIVE_LOW>;
+ spi-cpha;
+ spi-max-frequency = <4000000>;
+ spi-rx-delay-us = <1>;
+ spi-tx-delay-us = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@3 {
+ reg = <3>;
+ label = "rj45";
+ phy-handle = <&rj45_phy>;
+ phy-mode = "rgmii-id";
+ };
+
+ port@4 {
+ reg = <4>;
+ ethernet = <&fec>;
+ label = "cpu";
+ phy-mode = "rgmii-id";
+ rx-internal-delay-ps = <2000>;
+ tx-internal-delay-ps = <2000>;
+
+ /* Unreliable at 1000Mbps, limit RGMII to 100Mbps */
+ fixed-link {
+ full-duplex;
+ speed = <100>;
+ };
+ };
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "rgmii"; /* switch inserts delay */
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <0>;
+ status = "okay";
+
+ fixed-link {
+ full-duplex;
+ speed = <100>;
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rj45_phy: ethernet-phy@2 {
+ reg = <2>;
+ reset-gpios = <&gpio_exp_1 1 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <80000>;
+ };
+ };
+};
+
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ ak5558: codec@10 {
+ compatible = "asahi-kasei,ak5558";
+ reg = <0x10>;
+ reset-gpios = <&gpio_exp_1 2 GPIO_ACTIVE_LOW>;
+ };
+
+ gpio_exp_1: gpio@25 {
+ compatible = "nxp,pca9571";
+ reg = <0x25>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ tps65987ddh_0: usb-pd@20 {
+ compatible = "ti,tps6598x";
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tps65987ddh_0>;
+ interrupts-extended = <&gpio1 12 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ gpio_exp_2: gpio@25 {
+ compatible = "nxp,pca9571";
+ reg = <0x25>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ c0-hreset-hog {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ line-name = "c0-hreset";
+ output-low;
+ };
+
+ c1-hreset-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_LOW>;
+ line-name = "c1-hreset";
+ output-low;
+ };
+ };
+
+ fan53555: regulator@60 {
+ compatible = "fcs,fan53555";
+ reg = <0x60>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fan53555>;
+ regulator-name = "fan53555";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <980000>;
+ regulator-always-on;
+ regulator-boot-on;
+ fcs,suspend-voltage-selector = <1>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ ak4458: codec@11 {
+ compatible = "asahi-kasei,ak4458";
+ reg = <0x11>;
+ #sound-dai-cells = <0>;
+ reset-gpios = <&gpio_exp_2 5 GPIO_ACTIVE_LOW>;
+ };
+
+ tps65987ddh_1: usb-pd@20 {
+ compatible = "ti,tps6598x";
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tps65987ddh_1>;
+ interrupts-extended = <&gpio1 15 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&lcdif1 {
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+ assigned-clock-rates = <100000000>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ assigned-clocks = <&clk IMX8MP_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ non-removable;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x154
+ MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x154
+ MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x154
+ MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x154
+ >;
+ };
+
+ pinctrl_fan53555: fan53555grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x114
+ >;
+ };
+
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
+ MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
+ MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
+ MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
+ MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
+ MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
+ MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
+ MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
+ MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
+ MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
+ MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
+ MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
+ MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
+ MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154
+ MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART3_TXD__CAN2_RX 0x154
+ MX8MP_IOMUXC_UART3_RXD__CAN2_TX 0x154
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_ECSPI1_SCLK__I2C1_SCL 0x400000c3
+ MX8MP_IOMUXC_ECSPI1_MOSI__I2C1_SDA 0x400000c3
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400000c3
+ MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400000c3
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400000c3
+ MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400000c3
+ >;
+ };
+
+ pinctrl_pcie_refclk: pcierefclkgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART1_TXD__GPIO5_IO23 0xc6
+ >;
+ };
+
+ pinctrl_tps65987ddh_0: tps65987ddh-0grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12 0x1d0
+ >;
+ };
+
+ pinctrl_tps65987ddh_1: tps65987ddh-1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15 0x1d0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x040
+ MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x040
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x0d4
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0x166
+ >;
+ };
+};
--
2.51.0.297.gca2559c1d6
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v4 0/2] Mainline Protonic PRT8ML board
2025-10-14 13:09 [PATCH v4 0/2] Mainline Protonic PRT8ML board Jonas Rebmann
2025-10-14 13:09 ` [PATCH v4 1/2] dt-bindings: arm: fsl: Add Protonic PRT8ML Jonas Rebmann
2025-10-14 13:09 ` [PATCH v4 2/2] arm64: dts: add Protonic PRT8ML board Jonas Rebmann
@ 2025-10-27 6:06 ` Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Shawn Guo @ 2025-10-27 6:06 UTC (permalink / raw)
To: Jonas Rebmann
Cc: Andrew Lunn, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Liam Girdwood, Mark Brown, Shengjiu Wang, Shawn Guo,
Sascha Hauer, Fabio Estevam, Pengutronix Kernel Team,
Vladimir Oltean, netdev, devicetree, linux-kernel, linux-sound,
imx, linux-arm-kernel, Peng Fan, David Jander, Lucas Stach,
Oleksij Rempel
On Tue, Oct 14, 2025 at 03:09:30PM +0200, Jonas Rebmann wrote:
> Jonas Rebmann (2):
> dt-bindings: arm: fsl: Add Protonic PRT8ML
> arm64: dts: add Protonic PRT8ML board
Applied both, thanks!
^ permalink raw reply [flat|nested] 4+ messages in thread