From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from mail-wr1-f53.google.com (mail-wr1-f53.google.com [209.85.221.53]) (using TLSv1.2 with cipher ECDHE-RSA-AES128-GCM-SHA256 (128/128 bits)) (No client certificate requested) by smtp.subspace.kernel.org (Postfix) with ESMTPS id 07DCF303C97 for ; Fri, 9 Jan 2026 08:21:23 +0000 (UTC) Authentication-Results: smtp.subspace.kernel.org; arc=none smtp.client-ip=209.85.221.53 ARC-Seal:i=1; a=rsa-sha256; d=subspace.kernel.org; s=arc-20240116; t=1767946896; cv=none; b=Csnkq+BCtESgSEboalki7ViwuNvJp/HCvPyXcCSQVXcW1u88gLXJ4hEp4yyE2Oak+g/Motd7w1uymckHwRixU1Ej70sZ0uETtj2s9sQiqND6etO5h6CjHF6zMLWSN42vsw0WZlRSKqkh4NzMadnoKZi+yLKeDJgQVA9sh2co8Cg= ARC-Message-Signature:i=1; a=rsa-sha256; d=subspace.kernel.org; s=arc-20240116; t=1767946896; c=relaxed/simple; bh=4+/JZMqsrTLvC6BTE/UnUz/uSOHAYm++AXfPzhoMcRo=; h=Date:From:To:Cc:Subject:Message-ID:References:MIME-Version: Content-Type:Content-Disposition:In-Reply-To; b=ZwMBMqljfspk5+2Yor+F94and+kOg+20wgAmtk6oG5WmPxLjXUQ7vkMrdLFKp40iSmuR/t0BusNQ3AObwhk0aFpdQHf8g83SZHq7WQ58ceupdrwI3tURxdW7FCpVyl7f1ZnXmF4eiq/7+JQZQDFm21nYjOszKTvbQpL6Ut++CGk= ARC-Authentication-Results:i=1; smtp.subspace.kernel.org; dmarc=pass (p=none dis=none) header.from=gmail.com; spf=pass smtp.mailfrom=gmail.com; dkim=pass (2048-bit key) header.d=gmail.com header.i=@gmail.com header.b=IU/86URy; arc=none smtp.client-ip=209.85.221.53 Authentication-Results: smtp.subspace.kernel.org; dmarc=pass (p=none dis=none) header.from=gmail.com Authentication-Results: smtp.subspace.kernel.org; spf=pass smtp.mailfrom=gmail.com Authentication-Results: smtp.subspace.kernel.org; dkim=pass (2048-bit key) header.d=gmail.com header.i=@gmail.com header.b="IU/86URy" Received: by mail-wr1-f53.google.com with SMTP id ffacd0b85a97d-42fbad1fa90so3340290f8f.0 for ; Fri, 09 Jan 2026 00:21:21 -0800 (PST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20230601; t=1767946879; x=1768551679; darn=vger.kernel.org; h=in-reply-to:content-disposition:mime-version:references:message-id :subject:cc:to:from:date:from:to:cc:subject:date:message-id:reply-to; bh=bAaqO1edMEpG8D22KcxmchMJQR+sscKFymxMmmUQ79s=; b=IU/86URyXl1llALlfqIV5Rw/8NenSqVOlnIzsDJ6m1k7KCUtEtWC3C5wchfHECiJv1 3KKsGA/rI9ywqb5cX6cGDmVks/ukyWrVhoH/+m7gwxRlJYq7oUy/ZZQGM+x+HQ8NkovM wDbzOCSnuArPAvsIP91lfAdiQocbNCqPdPJywooCJKJj5lasjR7Wj4xWr5uaNS+5fudL uCpI42tbXn4vKY5EsgK9q+uBCqSIjNWljuE1BSZToZFhUpsEtMpcYNrYOoDKkg8ZM/iU eR11seF/UIe//6mW27VjQ8a8J54gDPZlg1BgQ9BSo/dZTwlj6C9wu9EaFoilIbomv8wZ v2Bw== X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=1e100.net; s=20230601; t=1767946879; x=1768551679; h=in-reply-to:content-disposition:mime-version:references:message-id :subject:cc:to:from:date:x-gm-gg:x-gm-message-state:from:to:cc :subject:date:message-id:reply-to; bh=bAaqO1edMEpG8D22KcxmchMJQR+sscKFymxMmmUQ79s=; b=fC7jMvO+C9anY1MIU3DYwRaTt5NVMaxxtCgr2MBrVpg2qPGElUKQSpIkA8aRWGHUuU s/xWqmCRXOqaw+9fD+fWu77SicLIjEK5L+bVx/iNmw5QlYRSlumLomGuB8mGBr4ReW6b uDQDfU4IK4aht8ksW247GPr+q6nomsRN+EckaAZHmOsghQ12w8DrKuDUsCznSVvIaquP +cdF7R8xWjI2rpAoqB04ke9y8VuvZKOzXstY3rxqKGcqEBqzFx3TRWnWErOAolMMBcBK yJ8kQ7d/nnYGDMSljJw6KY0jMNnJRsBhCF3fV50K1YtDhZJNekRzlgrk5exEDl/De1au gPAg== X-Forwarded-Encrypted: i=1; AJvYcCUjAqLH1LQjYxNGuXqLW2TD6Gwfn/B+GpdxPpQtHPs7IZXdva9HFpoNVV9/6cRwDxoRwrb9zaCrYen2@vger.kernel.org X-Gm-Message-State: AOJu0YyJzaxXFIO4DXy/pZwZSiIXZMvhX0gbIp3g6cf5VzfuKEDaZSCN Vq0KKUDs5sSUqnbx0xjCxPy+N3VzHJZg43iUCduvDVt/BaWDwkeukmEU X-Gm-Gg: AY/fxX5Z8LE8uzGVkciEP/sImQ1hTeVGJAUlzQ2Vnc3zxvIjHY36ZXYZYF5uCOMQ7qF y5rF27pPxKwqq3GoUSqahaJWnyPorxMpp17/njh2khGNTNBkA36z8NZ/iKNx4K6zmBDg2RtfSoo 9cjKsolcIoPQJeQCGTombP04fmV7yGrvmDgS2eOtb7cZ/YKuAYazndi7ZH0IGrC1sqkrA7RObhv 9RrlQJoMQgHZGLksLA492JlJGjqbXeNVJ4hqDedxPUSL98VvR63de0zrsq5l/DCfHgWKg0SMbbV D4Y4FuRshi3qiQGCoUr00c3oy0nvvwO4CC+lKOeMZgETTli97LoqSy8YtRKT1r8PTcYulwz/O1c qvOE0nlrJ9OyJp6u74qpLbYqtlHul04cw7J3P3J3sVxBbkiYkaASkBQgANX8j5w82Ztr5CADy+5 DRCio748NSgw4= X-Google-Smtp-Source: AGHT+IG9ya1IwVVkPrvQpXEW25miZ+F+tc85mHm67h5wQbXXz3z9xmfaPgBjvwnR9GqSZrgo1n09wg== X-Received: by 2002:a5d:5d0e:0:b0:431:66a:cbc3 with SMTP id ffacd0b85a97d-432c378a081mr8988878f8f.6.1767946878227; Fri, 09 Jan 2026 00:21:18 -0800 (PST) Received: from eichest-laptop ([2a02:168:af72:0:66a2:be50:e0d3:29f9]) by smtp.gmail.com with ESMTPSA id ffacd0b85a97d-432bd5fe83bsm21421414f8f.38.2026.01.09.00.21.17 (version=TLS1_3 cipher=TLS_AES_256_GCM_SHA384 bits=256/256); Fri, 09 Jan 2026 00:21:17 -0800 (PST) Date: Fri, 9 Jan 2026 09:21:15 +0100 From: Stefan Eichenberger To: Rob Herring Cc: andrew+netdev@lunn.ch, davem@davemloft.net, edumazet@google.com, kuba@kernel.org, pabeni@redhat.com, krzk+dt@kernel.org, conor+dt@kernel.org, netdev@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Stefan Eichenberger Subject: Re: [PATCH v2 1/2] dt-bindings: net: micrel: Convert to DT schema Message-ID: References: <20260108125208.29940-1-eichest@gmail.com> <20260108125208.29940-2-eichest@gmail.com> <20260108184845.GA758009-robh@kernel.org> Precedence: bulk X-Mailing-List: devicetree@vger.kernel.org List-Id: List-Subscribe: List-Unsubscribe: MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: <20260108184845.GA758009-robh@kernel.org> On Thu, Jan 08, 2026 at 12:48:45PM -0600, Rob Herring wrote: > On Thu, Jan 08, 2026 at 01:51:27PM +0100, Stefan Eichenberger wrote: > > From: Stefan Eichenberger > > > > Convert the devicetree bindings for the Micrel PHYs and switches to DT > > schema. > > > > Signed-off-by: Stefan Eichenberger > > --- > > .../devicetree/bindings/net/micrel.txt | 57 -------- > > .../devicetree/bindings/net/micrel.yaml | 133 ++++++++++++++++++ > > 2 files changed, 133 insertions(+), 57 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/net/micrel.txt > > create mode 100644 Documentation/devicetree/bindings/net/micrel.yaml > > > > diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt > > deleted file mode 100644 > > index 01622ce58112..000000000000 > > --- a/Documentation/devicetree/bindings/net/micrel.txt > > +++ /dev/null > > @@ -1,57 +0,0 @@ > > -Micrel PHY properties. > > - > > -These properties cover the base properties Micrel PHYs. > > - > > -Optional properties: > > - > > - - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs. > > - > > - Configure the LED mode with single value. The list of PHYs and the > > - bits that are currently supported: > > - > > - KSZ8001: register 0x1e, bits 15..14 > > - KSZ8041: register 0x1e, bits 15..14 > > - KSZ8021: register 0x1f, bits 5..4 > > - KSZ8031: register 0x1f, bits 5..4 > > - KSZ8051: register 0x1f, bits 5..4 > > - KSZ8081: register 0x1f, bits 5..4 > > - KSZ8091: register 0x1f, bits 5..4 > > - LAN8814: register EP5.0, bit 6 > > - > > - See the respective PHY datasheet for the mode values. > > - > > - - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select > > - bit selects 25 MHz mode > > - > > - Setting the RMII Reference Clock Select bit enables 25 MHz rather > > - than 50 MHz clock mode. > > - > > - Note that this option is only needed for certain PHY revisions with a > > - non-standard, inverted function of this configuration bit. > > - Specifically, a clock reference ("rmii-ref" below) is always needed to > > - actually select a mode. > > - > > - - clocks, clock-names: contains clocks according to the common clock bindings. > > - > > - supported clocks: > > - - KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference > > - input clock. Used to determine the XI input clock. > > - > > - - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode > > - > > - Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled > > - by the FXEN boot strapping pin. It can't be determined from the PHY > > - registers whether the PHY is in fiber mode, so this boolean device tree > > - property can be used to describe it. > > - > > - In fiber mode, auto-negotiation is disabled and the PHY can only work in > > - 100base-fx (full and half duplex) modes. > > - > > - - coma-mode-gpios: If present the given gpio will be deasserted when the > > - PHY is probed. > > - > > - Some PHYs have a COMA mode input pin which puts the PHY into > > - isolate and power-down mode. On some boards this input is connected > > - to a GPIO of the SoC. > > - > > - Supported on the LAN8814. > > diff --git a/Documentation/devicetree/bindings/net/micrel.yaml b/Documentation/devicetree/bindings/net/micrel.yaml > > new file mode 100644 > > index 000000000000..52d1b187e1d3 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/net/micrel.yaml > > @@ -0,0 +1,133 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/net/micrel.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Micrel KSZ series PHYs and switches > > + > > +maintainers: > > + - Andrew Lunn > > + - Stefan Eichenberger > > + > > +description: > > + The Micrel KSZ series contains different network phys and switches. > > + > > +properties: > > + compatible: > > + enum: > > + - ethernet-phy-id000e.7237 # KSZ8873MLL > > + - ethernet-phy-id0022.1430 # KSZ886X > > + - ethernet-phy-id0022.1435 # KSZ8863 > > + - ethernet-phy-id0022.1510 # KSZ8041 > > + - ethernet-phy-id0022.1537 # KSZ8041RNLI > > + - ethernet-phy-id0022.1550 # KSZ8051 > > + - ethernet-phy-id0022.1555 # KSZ8021 > > + - ethernet-phy-id0022.1556 # KSZ8031 > > + - ethernet-phy-id0022.1560 # KSZ8081, KSZ8091 > > + - ethernet-phy-id0022.1570 # KSZ8061 > > + - ethernet-phy-id0022.161a # KSZ8001 > > + - ethernet-phy-id0022.1720 # KS8737 > > + > > + micrel,fiber-mode: > > + type: boolean > > + description: | > > + If present the PHY is configured to operate in fiber mode. > > + > > + The KSZ8041FTL variant supports fiber mode, enabled by the FXEN > > + boot strapping pin. It can't be determined from the PHY registers > > + whether the PHY is in fiber mode, so this boolean device tree > > + property can be used to describe it. > > + > > + In fiber mode, auto-negotiation is disabled and the PHY can only > > + work in 100base-fx (full and half duplex) modes. > > + > > + micrel,led-mode: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: | > > + LED mode value to set for PHYs with configurable LEDs. > > + > > + Configure the LED mode with single value. The list of PHYs and the > > + bits that are currently supported: > > + > > + KSZ8001: register 0x1e, bits 15..14 > > + KSZ8041: register 0x1e, bits 15..14 > > + KSZ8021: register 0x1f, bits 5..4 > > + KSZ8031: register 0x1f, bits 5..4 > > + KSZ8051: register 0x1f, bits 5..4 > > + KSZ8081: register 0x1f, bits 5..4 > > + KSZ8091: register 0x1f, bits 5..4 > > + > > + See the respective PHY datasheet for the mode values. > > + minimum: 0 > > + maximum: 3 > > + > > +allOf: > > + - $ref: ethernet-phy.yaml# > > + - if: > > + not: > > + properties: > > + compatible: > > + contains: > > + const: ethernet-phy-id0022.1510 > > + then: > > + properties: > > + micrel,fiber-mode: false > > + - if: > > + not: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - ethernet-phy-id0022.1510 > > + - ethernet-phy-id0022.1555 > > + - ethernet-phy-id0022.1556 > > + - ethernet-phy-id0022.1550 > > + - ethernet-phy-id0022.1560 > > + - ethernet-phy-id0022.161a > > + then: > > + properties: > > + micrel,led-mode: false > > + - if: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - ethernet-phy-id0022.1555 > > + - ethernet-phy-id0022.1556 > > + - ethernet-phy-id0022.1560 > > + then: > > + properties: > > + clocks: > > + maxItems: 1 > > This has no effect because ethernet-phy.yaml already defines this. Thanks for the info. That means I would only set the clock-names and remove maxItems. I will fix that in the next version. > > + clock-names: > > + const: rmii-ref > > + description: > > + The RMII reference input clock. Used to determine the XI input > > + clock. > > + micrel,rmii-reference-clock-select-25-mhz: > > + type: boolean > > + description: | > > + RMII Reference Clock Select bit selects 25 MHz mode > > + > > + Setting the RMII Reference Clock Select bit enables 25 MHz rather > > + than 50 MHz clock mode. > > These should be defined at the top-level. Then use the if/then schema to > disallow the properties. The problem with this approach is, that because it has clock in its name, the DT schema valdiator will complain: devicetree/bindings/net/micrel.yaml: properties:micrel,rmii-reference-clock-select-25-mhz: 'anyOf' conditional failed, one must be fixed: 'maxItems' is a required property hint: Only "maxItems" is required for a single entry if there are no constraints defined for the values. 'type' is not one of ['maxItems', 'description', 'deprecated'] hint: Only "maxItems" is required for a single entry if there are no constraints defined for the values. Additional properties are not allowed ('type' was unexpected) hint: Arrays must be described with a combination of minItems/maxItems/items 'type' is not one of ['description', 'deprecated', 'const', 'enum', 'minimum', 'maximum', 'multipleOf', 'default', '$ref', 'oneOf'] hint: cell array properties must define how many entries and what the entries are when there is more than one entry. from schema $id: http://devicetree.org/meta-schemas/cell.yaml I couldn't find another way to define that Boolean type at top level. Is there an option to make the validator happy? Regards, Stefan