[PATCH v8 0/2] media: add Himax HM1246 image sensor

[PATCH v8 0/2] media: add Himax HM1246 image sensor

[Matthias Fend]

Hello,

this series adds support for the Himax HM1246 image sensor.
The Himax HM1246-AWD is a 1/3.7-Inch CMOS image sensor SoC with an active
array size of 1296 x 976.
Currently, only the native RAW mode is supported. Other modes and the
internal image signal processing pipeline are not currently supported.
The data sheet is available on the manufacturer's website [1].
Tested on i.MX8MP hardware. A Toshiba TC358746 bridge was used to convert
the sensor's parallel video output into MIPI signals for the i.MX8MP.

Best regards
 ~Matthias
 
[1] https://www.himax.com.tw/wp-content/uploads/2024/03/HM1246-AWD_DS_v01.pdf

v4l2-compliance 1.28.1, 64 bits, 64-bit time_t

Compliance test for device /dev/v4l-subdev4:

Driver Info:
        Driver version   : 6.12.0
        Capabilities     : 0x00000000
        Client Capabilities: 0x0000000000000003
streams interval-uses-which
Required ioctls:
        test VIDIOC_SUDBEV_QUERYCAP: OK
        test invalid ioctls: OK

Allow for multiple opens:
        test second /dev/v4l-subdev4 open: OK
        test VIDIOC_SUBDEV_QUERYCAP: OK
        test for unlimited opens: OK

Debug ioctls:
        test VIDIOC_LOG_STATUS: OK (Not Supported)

Input ioctls:
        test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
        test VIDIOC_ENUMAUDIO: OK (Not Supported)
        test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
        test VIDIOC_G/S_AUDIO: OK (Not Supported)
        Inputs: 0 Audio Inputs: 0 Tuners: 0

Output ioctls:
        test VIDIOC_G/S_MODULATOR: OK (Not Supported)
        test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
        test VIDIOC_ENUMAUDOUT: OK (Not Supported)
        test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
        test VIDIOC_G/S_AUDOUT: OK (Not Supported)
        Outputs: 0 Audio Outputs: 0 Modulators: 0

Input/Output configuration ioctls:
        test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
        test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
        test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
        test VIDIOC_G/S_EDID: OK (Not Supported)

Control ioctls:
        test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
        test VIDIOC_QUERYCTRL: OK
        test VIDIOC_G/S_CTRL: OK
        test VIDIOC_G/S/TRY_EXT_CTRLS: OK
        test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
        test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
        Standard Controls: 15 Private Controls: 0

Format ioctls:
        test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported)
        test VIDIOC_G/S_PARM: OK (Not Supported)
        test VIDIOC_G_FBUF: OK (Not Supported)
        test VIDIOC_G_FMT: OK (Not Supported)
        test VIDIOC_TRY_FMT: OK (Not Supported)
        test VIDIOC_S_FMT: OK (Not Supported)
        test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
        test Cropping: OK (Not Supported)
        test Composing: OK (Not Supported)
        test Scaling: OK (Not Supported)

Codec ioctls:
        test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
        test VIDIOC_G_ENC_INDEX: OK (Not Supported)
        test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)

Buffer ioctls:
        test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported)
        test CREATE_BUFS maximum buffers: OK
        test VIDIOC_REMOVE_BUFS: OK
        test VIDIOC_EXPBUF: OK (Not Supported)
        test Requests: OK (Not Supported)

Total for device /dev/v4l-subdev4: 45, Succeeded: 45, Failed: 0, Warnings: 0

Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
---
Changes in v8:
- Adjusted copyright year (Sakari)
- Use local var for unreferenced v4l2 controls (Sakari)
- Return NULL instead of PTR_ERR if hm1246_find_mode_by_mbus_code() fails (Sakari)
- Removed unnecessary parentheses (Sakari)
- Dropped git reference in MAINTAINER entry (Sakari)
- Added default for bus-width in bindings (Sakari)
- Link to v7: https://lore.kernel.org/r/20260112-hm1246-v7-0-fee8587f2808@emfend.at

Changes in v7:
- Expect the PLL to generate the exact link frequency specified in DT (Laurent, Sakari)
- Dropped {g,s}_register functions
- Link to v6: https://lore.kernel.org/r/20251202-hm1246-v6-0-3e96ed6b3ffa@emfend.at

Changes in v6:
- Rework includes to follow include-what-you-use (Andy)
- Replace 'fsleep(6000)' with 'fsleep(6 * USEC_PER_MSEC)' (Andy)
- Simplify hm1246_get_selection() return (Andy)
- Use explicit indexes for test pattern array (Andy)
- Improve some line-wrappings (Andy)
- Avoid using __maybe_unused (Andy)
- Drop an unnecessary type cast (Andy)
- Use '0' instead of '0x0' (Andy)
- Reword comments about timings (Andy)
- Simplify error handling of hm1246_init_controls() (Sakari)
- Revert 'rework PLL calc to use goto' (Andy, Sakari)
- Link to v5: https://lore.kernel.org/r/20251104-hm1246-v5-0-97c8f25b5419@emfend.at

Changes in v5:
- Converted to lower case hexadecimals
- Use consistent returns in switch of hm1246_get_selection()
- Adjust some variable types/attributes
- Removed redundant parentheses
- Rework PLL calc to use goto
- Simplified some function returns
- Use array definition for test patterns
- Source format adjustments
- Properly init minimum of pixel_rate control
- dropped hm1246_update_controls()
- require and check DT link frequencies
- Link to v4: https://lore.kernel.org/r/20251017-hm1246-v4-0-e3388ea2f08c@emfend.at

Changes in v4:
- Split changes to MAINTAINERS into commits
- Fix comma after statement (use semicolon)
- Replace abs() with abs_diff() in PLL calculation
- Inverse needs_cmu_update logic
- Drop mode from hm1246_set_ctrl()
- Return if xclk frequency is out of range
- Fix reset_gpio dev_err_probe()
- Rebased on media-committers/next
- Link to v3: https://lore.kernel.org/r/20250912-hm1246-v3-0-3b89f47dfa43@emfend.at

Changes in v3:
- Bindings: Remove bus-type and add default polarity values
- Select V4L2_CCI_I2C
- Convert additional macros to use HZ_PER_*
- Replace cur_mode with v4l2_find_nearest_size()
- Remove duplicates in the register init sequence
- Use container_of_const
- Check return of hm1246_update_controls()
- Correct multi-line comments
- Replace hm1246_cci_write_cmu()
- Consistently use hm1246->dev
- Use pm_runtime_put_autosuspend()
- Remove v4l2 event handling
- Convert to devm_v4l2_sensor_clk_get()
- Configure PM before registering subdev
- Link to v2: https://lore.kernel.org/r/20250526-hm1246-v2-0-6b882827a3a5@emfend.at
- Depends-on: https://lore.kernel.org/all/20250707143253.167910-1-mehdi.djait@linux.intel.com/

Changes in v2:
- Use macros for 64-bit division
- Avoid compiler warnings about potentially uninitialized variables
- Fix two uses of dev_err_probe
- Link to v1: https://lore.kernel.org/r/20250403-hm1246-v1-0-30990d71bc42@emfend.at

---
Matthias Fend (2):
      media: dt-bindings: i2c: add Himax HM1246 image sensor
      media: i2c: add Himax HM1246 image sensor driver

 .../bindings/media/i2c/himax,hm1246.yaml           |  120 ++
 MAINTAINERS                                        |    7 +
 drivers/media/i2c/Kconfig                          |   10 +
 drivers/media/i2c/Makefile                         |    1 +
 drivers/media/i2c/hm1246.c                         | 1298 ++++++++++++++++++++
 5 files changed, 1436 insertions(+)
---
base-commit: 3aa9296a23ec41a8424e9a2346eea59fb6cb7d8c
change-id: 20250403-hm1246-96b0cdab773c

Best regards,
-- 
Matthias Fend <matthias.fend@emfend.at>

[PATCH v8 1/2] media: dt-bindings: i2c: add Himax HM1246 image sensor

[Matthias Fend]

Add YAML device tree binding for Himax HM1246 image sensor.

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
---
 .../bindings/media/i2c/himax,hm1246.yaml           | 120 +++++++++++++++++++++
 MAINTAINERS                                        |   6 ++
 2 files changed, 126 insertions(+)

diff --git a/Documentation/devicetree/bindings/media/i2c/himax,hm1246.yaml b/Documentation/devicetree/bindings/media/i2c/himax,hm1246.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..a65488fcc643fd1e2b9435224813f35f2b4397c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/himax,hm1246.yaml
@@ -0,0 +1,120 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright 2025 Matthias Fend <matthias.fend@emfend.at>
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/himax,hm1246.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Himax HM1246-AWD 1/3.7-Inch megapixel SoC image sensor
+
+maintainers:
+  - Matthias Fend <matthias.fend@emfend.at>
+
+description:
+  The Himax HM1246-AWD is a 1/3.7-Inch CMOS image sensor SoC with an active
+  array size of 1296 x 976. It is programmable through an I2C interface and
+  connected via parallel bus.
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: himax,hm1246
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: Input reference clock (6 - 27 MHz)
+    maxItems: 1
+
+  reset-gpios:
+    description: Active low XSHUTDOWN pin
+    maxItems: 1
+
+  avdd-supply:
+    description: Power for analog circuit (3.0 - 3.6 V)
+
+  iovdd-supply:
+    description: Power for I/O circuit (1.7 - 3.6 V)
+
+  dvdd-supply:
+    description: Power for digital circuit (1.5 / 1.8 V)
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+    description: Parallel video output port
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          bus-width:
+            default: 10
+
+          hsync-active:
+            default: 1
+
+          vsync-active:
+            default: 1
+
+          pclk-sample:
+            default: 0
+
+        required:
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - avdd-supply
+  - iovdd-supply
+  - dvdd-supply
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/media/video-interfaces.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sensor@24 {
+            compatible =  "himax,hm1246";
+            reg = <0x24>;
+
+            clocks = <&hm1246_clk>;
+
+            reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+
+            avdd-supply = <&hm1246_avdd>;
+            iovdd-supply = <&hm1246_iovdd>;
+            dvdd-supply = <&hm1246_dvdd>;
+
+            orientation = <2>;
+            rotation = <0>;
+
+            port {
+                endpoint {
+                    remote-endpoint = <&isp_par_in>;
+                    bus-width = <10>;
+                    hsync-active = <1>; /* active high */
+                    vsync-active = <1>; /* active high */
+                    pclk-sample = <1>; /* sample on rising edge */
+                    link-frequencies = /bits/ 64 <42200000>;
+                };
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 752ccaea38b0ee74282e06f233463eba122fa92c..2ea776c417dd0ca3231713a827b421778c92d543 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11290,6 +11290,12 @@ L:	linux-kernel@vger.kernel.org
 S:	Maintained
 F:	drivers/misc/hisi_hikey_usb.c
 
+HIMAX HM1246 SENSOR DRIVER
+M:	Matthias Fend <matthias.fend@emfend.at>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/i2c/himax,hm1246.yaml
+
 HIMAX HX83112B TOUCHSCREEN SUPPORT
 M:	Job Noorman <job@noorman.info>
 L:	linux-input@vger.kernel.org

-- 
2.34.1

[PATCH v8 2/2] media: i2c: add Himax HM1246 image sensor driver

[Matthias Fend]

Add a V4L2 sub-device driver for Himax HM1246 image sensor.

The Himax HM1246-AWD is a 1/3.7-Inch CMOS image sensor SoC with an active
array size of 1296 x 976. It is programmable through an I2C interface and
connected via parallel bus.

The sensor has an internal ISP with a complete image processing pipeline
including control loops. However, this driver uses the sensor in raw mode
and the entire ISP is bypassed.

Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
---
 MAINTAINERS                |    1 +
 drivers/media/i2c/Kconfig  |   10 +
 drivers/media/i2c/Makefile |    1 +
 drivers/media/i2c/hm1246.c | 1298 ++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 1310 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 2ea776c417dd0ca3231713a827b421778c92d543..d2f8f9c3c0b2c0bd176fd01854d866ddcce4a0f0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11295,6 +11295,7 @@ M:	Matthias Fend <matthias.fend@emfend.at>
 L:	linux-media@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/media/i2c/himax,hm1246.yaml
+F:	drivers/media/i2c/hm1246.c
 
 HIMAX HX83112B TOUCHSCREEN SUPPORT
 M:	Job Noorman <job@noorman.info>
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 6dcae0aa98ee4411a4a66ea50f7354a6305099c7..b995f382aae7beddef9cf05f696314589363f0c7 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -137,6 +137,16 @@ config VIDEO_HI847
           To compile this driver as a module, choose M here: the
           module will be called hi847.
 
+config VIDEO_HM1246
+	tristate "Himax HM1246 sensor support"
+	select V4L2_CCI_I2C
+	help
+	  This is a Video4Linux2 sensor driver for the Himax
+	  HM1246 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hm1246.
+
 config VIDEO_IMX111
 	tristate "Sony IMX111 sensor support"
 	select V4L2_CCI_I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index a3a6396df3c4525c894238c9c4724684cf1f464c..44e2e01bd6b1d853debcae57c8889c16a40b7a2b 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -45,6 +45,7 @@ obj-$(CONFIG_VIDEO_GC2145) += gc2145.o
 obj-$(CONFIG_VIDEO_HI556) += hi556.o
 obj-$(CONFIG_VIDEO_HI846) += hi846.o
 obj-$(CONFIG_VIDEO_HI847) += hi847.o
+obj-$(CONFIG_VIDEO_HM1246) += hm1246.o
 obj-$(CONFIG_VIDEO_I2C) += video-i2c.o
 obj-$(CONFIG_VIDEO_IMX111) += imx111.o
 obj-$(CONFIG_VIDEO_IMX208) += imx208.o
diff --git a/drivers/media/i2c/hm1246.c b/drivers/media/i2c/hm1246.c
new file mode 100644
index 0000000000000000000000000000000000000000..74ed0f34f0b08050673b685dff3ee04dc547752a
--- /dev/null
+++ b/drivers/media/i2c/hm1246.c
@@ -0,0 +1,1298 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for Himax HM1246 image sensor
+ *
+ * Copyright 2026 Matthias Fend <matthias.fend@emfend.at>
+ */
+
+#include <linux/array_size.h>
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/limits.h>
+#include <linux/math.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regulator/consumer.h>
+#include <linux/types.h>
+#include <linux/units.h>
+#include <media/media-entity.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-cci.h>
+#include <media/v4l2-common.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+
+/* Status registers */
+#define HM1246_MODEL_ID_REG		 CCI_REG16(0x0000)
+
+/* General setup registers */
+#define HM1246_MODE_SELECT_REG		 CCI_REG8(0x0100)
+#define HM1246_MODE_SELECT_STANDBY	 0x00
+#define HM1246_MODE_SELECT_STREAM	 0x01
+#define HM1246_MODE_SELECT_STOP		 0x02
+#define HM1246_IMAGE_ORIENTATION_REG	 CCI_REG8(0x0101)
+#define HM1246_IMAGE_ORIENTATION_VFLIP	 BIT(1)
+#define HM1246_IMAGE_ORIENTATION_HFLIP	 BIT(0)
+#define HM1246_CMU_UPDATE_REG		 CCI_REG8(0x0104)
+
+/* Output setup registers */
+#define HM1246_COARSE_INTG_REG		 CCI_REG16(0x0202)
+#define HM1246_ANALOG_GLOBAL_GAIN_REG	 CCI_REG8(0x0205)
+
+/* Clock setup registers */
+#define HM1246_PLL1CFG_REG		 CCI_REG8(0x0303)
+#define HM1246_PLL1CFG_MULTIPLIER(x)	 (((x) & 0xff) << 0)
+#define HM1246_PLL2CFG_REG		 CCI_REG8(0x0305)
+#define HM1246_PLL2CFG_PRE_DIV(x)	 (((x) & 0x1f) << 1)
+#define HM1246_PLL2CFG_MULTIPLIER(x)	 (((x) & 0x01) << 0)
+#define HM1246_PLL3CFG_REG		 CCI_REG8(0x0307)
+#define HM1246_PLL3CFG_POST_DIV(x)	 (((x) & 0x3) << 6)
+#define HM1246_PLL3CFG_SYSCLK_DIV(x)	 (((x) & 0x3) << 4)
+#define HM1246_PLL3CFG_PCLK_DIV(x)	 (((x) & 0x7) << 0)
+
+/* Frame timing registers */
+#define HM1246_FRAME_LENGTH_LINES_REG	 CCI_REG16(0x0340)
+#define HM1246_LINE_LENGTH_PCK_REG	 CCI_REG16(0x0342)
+
+/* Image size registers */
+#define HM1246_X_ADDR_START_REG		 CCI_REG16(0x0344)
+#define HM1246_Y_ADDR_START_REG		 CCI_REG16(0x0346)
+#define HM1246_X_ADDR_END_REG		 CCI_REG16(0x0348)
+#define HM1246_Y_ADDR_END_REG		 CCI_REG16(0x034a)
+#define HM1246_X_LA_START_REG		 CCI_REG16(0x0351)
+#define HM1246_X_LA_END_REG		 CCI_REG16(0x0353)
+#define HM1246_Y_LA_START_REG		 CCI_REG16(0x0355)
+#define HM1246_Y_LA_END_REG		 CCI_REG16(0x0357)
+
+/* Test pattern registers */
+#define HM1246_TEST_PATTERN_MODE_REG	 CCI_REG8(0x0601)
+#define HM1246_TEST_PATTERN_MODE_MODE(x) (((x) & 0xf) << 4)
+#define HM1246_TEST_PATTERN_MODE_ENABLE	 BIT(0)
+#define HM1246_TEST_DATA_BLUE_REG	 CCI_REG16(0x0602)
+#define HM1246_TEST_DATA_GB_REG		 CCI_REG16(0x0604)
+#define HM1246_TEST_DATA_RED_REG	 CCI_REG16(0x0606)
+#define HM1246_TEST_DATA_GR_REG		 CCI_REG16(0x0608)
+
+/* SBC registers */
+#define HM1246_SBC_BOOT_REF2_REG	 CCI_REG8(0x2001)
+#define HM1246_SBC_BOOT_REF2_PLL_LOCK	 BIT(4)
+#define HM1246_SBC_CTRL_REG		 CCI_REG8(0x2003)
+#define HM1246_SBC_CTRL_PLL_EN		 BIT(0)
+
+/* System registers */
+#define HM1246_OUTPUT_PRT_CTRL_REG	 CCI_REG8(0x2f02)
+#define HM1246_POLARITY_CTRL_REG	 CCI_REG8(0x2f20)
+#define HM1246_POLARITY_CTRL_HSYNC	 BIT(7)
+#define HM1246_POLARITY_CTRL_VSYNC	 BIT(6)
+#define HM1246_PCLK_CTRL_REG		 CCI_REG8(0x2f24)
+#define HM1246_PCLK_CTRL_POL		 BIT(3)
+
+/* Digital window control & parameter registers */
+#define HM1246_DWIN_XOFFSET_REG		 CCI_REG16(0xd5e4)
+#define HM1246_DWIN_XSIZE_REG		 CCI_REG16(0xd5e6)
+#define HM1246_DWIN_YOFFSET_REG		 CCI_REG16(0xd5e8)
+#define HM1246_DWIN_YSIZE_REG		 CCI_REG16(0xd5ea)
+
+#define HM1246_MODEL_ID			 0x1245
+
+#define HM1246_NATIVE_WIDTH		 1296
+#define HM1246_NATIVE_HEIGHT		 976
+
+#define HM1246_VTS_MAX			 65535
+
+#define HM1246_COARSE_INTG_MARGIN	 2
+#define HM1246_COARSE_INTG_MIN		 4
+#define HM1246_COARSE_INTG_STEP		 1
+
+#define HM1246_ANALOG_GLOBAL_GAIN_MIN	 0x00
+#define HM1246_ANALOG_GLOBAL_GAIN_MAX	 0xe8
+#define HM1246_ANALOG_GLOBAL_GAIN_STEP	 1
+
+#define HM1246_XCLK_MIN			 (6 * HZ_PER_MHZ)
+#define HM1246_XCLK_MAX			 (27 * HZ_PER_MHZ)
+
+#define HM1246_PCLK_MIN			 (8 * HZ_PER_MHZ)
+#define HM1246_PCLK_MAX			 (96 * HZ_PER_MHZ)
+
+#define HM1246_PLL_VCO_MIN		 (360 * HZ_PER_MHZ)
+#define HM1246_PLL_VCO_MAX		 (680 * HZ_PER_MHZ)
+
+#define HM1246_PLL_INCLK_MIN		 (1000 * HZ_PER_KHZ)
+#define HM1246_PLL_INCLK_MAX		 (2500 * HZ_PER_KHZ)
+
+#define HM1246_PLL_MULTI_L_MIN		 1
+#define HM1246_PLL_MULTI_L_MAX		 256
+
+#define HM1246_PLL_MULTI_H_MIN		 2
+#define HM1246_PLL_MULTI_H_MAX		 3
+
+#define HM1246_PLL_MULTI_MIN \
+	(HM1246_PLL_MULTI_H_MIN * HM1246_PLL_MULTI_L_MIN)
+#define HM1246_PLL_MULTI_MAX \
+	(HM1246_PLL_MULTI_H_MAX * HM1246_PLL_MULTI_L_MAX)
+
+static const char *const hm1246_test_pattern_menu[] = {
+	"Disabled",
+	"Checkboard",
+	"Ramp",
+	"Moving ones",
+	"Blending color bars",
+	"Color bars",
+	"Solid white",
+	"Solid black",
+	"Solid red",
+	"Solid green",
+	"Solid blue",
+};
+
+static const char *const hm1246_supply_names[] = {
+	"avdd",
+	"iovdd",
+	"dvdd",
+};
+
+struct hm1246 {
+	struct device *dev;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(hm1246_supply_names)];
+	struct clk *xclk;
+	unsigned long xclk_freq;
+	struct gpio_desc *reset_gpio;
+	unsigned int mbus_flags;
+	s64 link_frequency;
+
+	struct v4l2_ctrl_handler ctrls;
+	struct v4l2_ctrl *exposure_ctrl;
+	struct v4l2_ctrl *hflip_ctrl;
+	struct v4l2_ctrl *vflip_ctrl;
+
+	struct regmap *regmap;
+
+	bool identified;
+};
+
+static const struct cci_reg_sequence mode_1296x976_raw[] = {
+	{ HM1246_X_LA_START_REG, 60 },
+	{ HM1246_X_LA_END_REG, 1355 },
+	{ HM1246_Y_LA_START_REG, 0 },
+	{ HM1246_Y_LA_END_REG, 975 },
+	{ HM1246_OUTPUT_PRT_CTRL_REG, 0x20 },
+	{ CCI_REG8(0x300a), 0x01 },
+	{ CCI_REG8(0x300b), 0x00 },
+	{ CCI_REG8(0x50f5), 0x01 },
+	{ CCI_REG8(0x50dd), 0x00 },
+	{ CCI_REG8(0x50a1), 0x02 },
+	{ CCI_REG8(0x50aa), 0x1c },
+	{ CCI_REG8(0x50ac), 0xdd },
+	{ CCI_REG8(0x50ad), 0x08 },
+	{ CCI_REG8(0x50ab), 0x04 },
+	{ CCI_REG8(0x50a0), 0x40 },
+	{ CCI_REG8(0x50a2), 0x12 },
+	{ CCI_REG8(0x50ae), 0x30 },
+	{ CCI_REG8(0x50b3), 0x04 },
+	{ CCI_REG8(0x5204), 0x40 },
+	{ CCI_REG8(0x5208), 0x55 },
+	{ CCI_REG8(0x520b), 0x05 },
+	{ CCI_REG8(0x520d), 0x40 },
+	{ CCI_REG8(0x5214), 0x18 },
+	{ CCI_REG8(0x5215), 0x0f },
+	{ CCI_REG8(0x5217), 0x01 },
+	{ CCI_REG8(0x5218), 0x07 },
+	{ CCI_REG8(0x5219), 0x01 },
+	{ CCI_REG8(0x521a), 0x50 },
+	{ CCI_REG8(0x521b), 0x24 },
+	{ CCI_REG8(0x5232), 0x01 },
+	{ CCI_REG8(0x5220), 0x11 },
+	{ CCI_REG8(0x5227), 0x01 },
+	{ CCI_REG8(0x5106), 0xc1 },
+	{ CCI_REG8(0x5115), 0xc0 },
+	{ CCI_REG8(0x5116), 0xc1 },
+	{ CCI_REG8(0x5138), 0x40 },
+	{ CCI_REG8(0x5139), 0x60 },
+	{ CCI_REG8(0x513a), 0x80 },
+	{ CCI_REG8(0x513b), 0xa0 },
+	{ CCI_REG8(0x513c), 0xa1 },
+	{ CCI_REG8(0x513d), 0xa2 },
+	{ CCI_REG8(0x513e), 0xa3 },
+	{ CCI_REG8(0x5140), 0x40 },
+	{ CCI_REG8(0x5141), 0x60 },
+	{ CCI_REG8(0x5142), 0x80 },
+	{ CCI_REG8(0x5143), 0x81 },
+	{ CCI_REG8(0x5144), 0x82 },
+	{ CCI_REG8(0x5145), 0x83 },
+	{ CCI_REG8(0x5146), 0x93 },
+	{ CCI_REG8(0x51c1), 0xc3 },
+	{ CCI_REG8(0x51c5), 0xc3 },
+	{ CCI_REG8(0x51c9), 0xc3 },
+	{ CCI_REG8(0x51cd), 0xc2 },
+	{ CCI_REG8(0x51d1), 0xc1 },
+	{ CCI_REG8(0x51d5), 0xc1 },
+	{ CCI_REG8(0x51d9), 0x81 },
+	{ CCI_REG8(0x51dd), 0x81 },
+	{ CCI_REG8(0x51c2), 0x49 },
+	{ CCI_REG8(0x51c6), 0x49 },
+	{ CCI_REG8(0x51ca), 0x49 },
+	{ CCI_REG8(0x51ce), 0x49 },
+	{ CCI_REG8(0x51d2), 0x49 },
+	{ CCI_REG8(0x51d6), 0x59 },
+	{ CCI_REG8(0x51da), 0x59 },
+	{ CCI_REG8(0x51de), 0x59 },
+	{ CCI_REG8(0x51c3), 0x20 },
+	{ CCI_REG8(0x51c7), 0x38 },
+	{ CCI_REG8(0x51cb), 0x21 },
+	{ CCI_REG8(0x51cf), 0x11 },
+	{ CCI_REG8(0x51d3), 0x11 },
+	{ CCI_REG8(0x51d7), 0x13 },
+	{ CCI_REG8(0x51db), 0x13 },
+	{ CCI_REG8(0x51df), 0x13 },
+	{ CCI_REG8(0x51e0), 0x03 },
+	{ CCI_REG8(0x51e2), 0x03 },
+	{ CCI_REG8(0x51f0), 0x42 },
+	{ CCI_REG8(0x51f1), 0x40 },
+	{ CCI_REG8(0x51f2), 0x4a },
+	{ CCI_REG8(0x51f3), 0x48 },
+	{ CCI_REG8(0x5015), 0x73 },
+	{ CCI_REG8(0x504a), 0x04 },
+	{ CCI_REG8(0x5044), 0x07 },
+	{ CCI_REG8(0x5040), 0x03 },
+	{ CCI_REG8(0x5135), 0xc4 },
+	{ CCI_REG8(0x5136), 0xc5 },
+	{ CCI_REG8(0x5166), 0xc4 },
+	{ CCI_REG8(0x5196), 0xc4 },
+	{ CCI_REG8(0x51c0), 0x10 },
+	{ CCI_REG8(0x51c4), 0x10 },
+	{ CCI_REG8(0x51c8), 0xa0 },
+	{ CCI_REG8(0x51cc), 0xa0 },
+	{ CCI_REG8(0x51d0), 0xa1 },
+	{ CCI_REG8(0x51d4), 0xa5 },
+	{ CCI_REG8(0x51d8), 0xa5 },
+	{ CCI_REG8(0x51dc), 0xa5 },
+	{ CCI_REG8(0x5200), 0xe4 },
+	{ CCI_REG8(0x5209), 0x04 },
+	{ CCI_REG8(0x301b), 0x01 },
+	{ CCI_REG8(0x3130), 0x01 },
+	{ CCI_REG8(0x5013), 0x07 },
+	{ CCI_REG8(0x5016), 0x01 },
+	{ CCI_REG8(0x501d), 0x50 },
+	{ CCI_REG8(0x0350), 0xfe },
+	{ CCI_REG8(0x2f03), 0x15 },
+	{ CCI_REG8(0xd380), 0x00 },
+	{ CCI_REG8(0x3047), 0x7f },
+	{ CCI_REG8(0x304d), 0x34 },
+	{ CCI_REG8(0x3041), 0x4b },
+	{ CCI_REG8(0x3042), 0x2d },
+	{ CCI_REG8(0x3056), 0x64 },
+	{ CCI_REG8(0x3059), 0x1e },
+	{ CCI_REG8(0x305e), 0x10 },
+	{ CCI_REG8(0x305f), 0x10 },
+	{ CCI_REG8(0x306d), 0x10 },
+	{ CCI_REG8(0x306e), 0x0c },
+	{ CCI_REG8(0x3064), 0x50 },
+	{ CCI_REG8(0x3067), 0x78 },
+	{ CCI_REG8(0x3068), 0x4b },
+	{ CCI_REG8(0x306a), 0x78 },
+	{ CCI_REG8(0x306b), 0x4b },
+	{ CCI_REG8(0xd442), 0x3d },
+	{ CCI_REG8(0xd443), 0x06 },
+	{ CCI_REG8(0xd440), 0x63 },
+	{ CCI_REG8(0xd446), 0xb0 },
+	{ CCI_REG8(0xd447), 0x60 },
+	{ CCI_REG8(0xd448), 0x48 },
+	{ CCI_REG8(0xd449), 0x30 },
+	{ CCI_REG8(0xd44a), 0x18 },
+	{ CCI_REG8(0xd360), 0x03 },
+	{ CCI_REG8(0x30ac), 0x10 },
+	{ CCI_REG8(0x30ad), 0x10 },
+	{ CCI_REG8(0x30ae), 0x10 },
+	{ CCI_REG8(0x3040), 0x0b },
+	{ CCI_REG8(0x2002), 0x00 },
+	{ CCI_REG8(0x2000), 0x08 },
+};
+
+struct hm1246_reg_list {
+	u32 num_of_regs;
+	const struct cci_reg_sequence *regs;
+};
+
+struct hm1246_mode {
+	u32 codes[4];
+	u32 clocks_per_pixel;
+	u32 top;
+	u32 left;
+	u32 width;
+	u32 height;
+	u32 hts;
+	u32 vts_min;
+	const struct hm1246_reg_list reg_list;
+};
+
+#define FLIP_FORMAT_INDEX(v, h) ((v ? 2 : 0) | (h ? 1 : 0))
+
+/* Get the format code of the mode considering current flip setting. */
+static u32 hm1246_get_format_code(struct hm1246 *hm1246,
+				  const struct hm1246_mode *hm1246_mode)
+{
+	return hm1246_mode->codes[FLIP_FORMAT_INDEX(hm1246->vflip_ctrl->val,
+						    hm1246->hflip_ctrl->val)];
+}
+
+static const struct hm1246_mode hm1246_modes[] = {
+	{
+		.codes = {
+			[FLIP_FORMAT_INDEX(0, 0)] = MEDIA_BUS_FMT_SBGGR10_1X10,
+			[FLIP_FORMAT_INDEX(0, 1)] = MEDIA_BUS_FMT_SGBRG10_1X10,
+			[FLIP_FORMAT_INDEX(1, 0)] = MEDIA_BUS_FMT_SGRBG10_1X10,
+			[FLIP_FORMAT_INDEX(1, 1)] = MEDIA_BUS_FMT_SRGGB10_1X10,
+		},
+		.clocks_per_pixel = 1,
+		.top = 0,
+		.left = 0,
+		.width = 1296,
+		.height = 976,
+		.hts = 1420,
+		.vts_min = 990,
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(mode_1296x976_raw),
+			.regs = mode_1296x976_raw,
+		},
+	},
+};
+
+static inline struct hm1246 *to_hm1246(struct v4l2_subdev *sd)
+{
+	return container_of_const(sd, struct hm1246, sd);
+}
+
+static const struct hm1246_mode *
+hm1246_find_mode_by_mbus_code(struct hm1246 *hm1246, u32 code)
+{
+	for (unsigned int i = 0; i < ARRAY_SIZE(hm1246_modes); i++) {
+		if (code == hm1246_get_format_code(hm1246, &hm1246_modes[i]))
+			return &hm1246_modes[i];
+	}
+
+	return NULL;
+}
+
+static int hm1246_power_on(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct hm1246 *hm1246 = to_hm1246(sd);
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(hm1246_supply_names),
+				    hm1246->supplies);
+	if (ret) {
+		dev_err(hm1246->dev, "failed to enable regulators\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(hm1246->xclk);
+	if (ret) {
+		regulator_bulk_disable(ARRAY_SIZE(hm1246_supply_names),
+				       hm1246->supplies);
+		dev_err(hm1246->dev, "failed to enable clock\n");
+		return ret;
+	}
+
+	gpiod_set_value_cansleep(hm1246->reset_gpio, 0);
+
+	/*
+	 * XSHUTDOWN to crystal clock oscillation (tcrystal):  650us (typical)
+	 * Sample bootstrap pin (tsample):                    2000us (maximum)
+	 * Built in self test (tbist):                        3000us (maximum)
+	 */
+	fsleep(6 * USEC_PER_MSEC);
+
+	return 0;
+}
+
+static int hm1246_power_off(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct hm1246 *hm1246 = to_hm1246(sd);
+
+	gpiod_set_value_cansleep(hm1246->reset_gpio, 1);
+
+	clk_disable_unprepare(hm1246->xclk);
+
+	regulator_bulk_disable(ARRAY_SIZE(hm1246_supply_names),
+			       hm1246->supplies);
+
+	return 0;
+}
+
+static int hm1246_enum_mbus_code(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *sd_state,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct hm1246 *hm1246 = to_hm1246(sd);
+
+	if (code->index >= ARRAY_SIZE(hm1246_modes))
+		return -EINVAL;
+
+	code->code = hm1246_get_format_code(hm1246, &hm1246_modes[code->index]);
+
+	return 0;
+}
+
+static int hm1246_enum_frame_size(struct v4l2_subdev *subdev,
+				  struct v4l2_subdev_state *sd_state,
+				  struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct hm1246 *hm1246 = to_hm1246(subdev);
+	const struct hm1246_mode *mode;
+
+	if (fse->index > 0)
+		return -EINVAL;
+
+	mode = hm1246_find_mode_by_mbus_code(hm1246, fse->code);
+	if (!mode)
+		return -EINVAL;
+
+	fse->min_width = mode->width;
+	fse->max_width = mode->width;
+	fse->min_height = mode->height;
+	fse->max_height = mode->height;
+
+	return 0;
+}
+
+static void hm1246_update_pad_format(struct hm1246 *hm1246,
+				     const struct hm1246_mode *hm1246_mode,
+				     struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width = hm1246_mode->width;
+	fmt->height = hm1246_mode->height;
+	fmt->code = hm1246_get_format_code(hm1246, hm1246_mode);
+	fmt->field = V4L2_FIELD_NONE;
+	fmt->colorspace = V4L2_COLORSPACE_RAW;
+	fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->colorspace);
+	fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
+	fmt->xfer_func = V4L2_XFER_FUNC_NONE;
+}
+
+static int hm1246_set_format(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *state,
+			     struct v4l2_subdev_format *fmt)
+{
+	struct hm1246 *hm1246 = to_hm1246(sd);
+	struct v4l2_mbus_framefmt *mbus_fmt;
+	struct v4l2_rect *crop;
+	const struct hm1246_mode *mode;
+
+	mode = hm1246_find_mode_by_mbus_code(hm1246, fmt->format.code);
+	if (!mode)
+		mode = &hm1246_modes[0];
+
+	crop = v4l2_subdev_state_get_crop(state, 0);
+	crop->top = mode->top;
+	crop->left = mode->left;
+	crop->width = mode->width;
+	crop->height = mode->height;
+
+	hm1246_update_pad_format(hm1246, mode, &fmt->format);
+	mbus_fmt = v4l2_subdev_state_get_format(state, 0);
+	*mbus_fmt = fmt->format;
+
+	return 0;
+}
+
+static int hm1246_get_selection(struct v4l2_subdev *sd,
+				struct v4l2_subdev_state *state,
+				struct v4l2_subdev_selection *sel)
+{
+	const struct v4l2_mbus_framefmt *format;
+	const struct hm1246_mode *mode;
+
+	format = v4l2_subdev_state_get_format(state, 0);
+	mode = v4l2_find_nearest_size(hm1246_modes, ARRAY_SIZE(hm1246_modes),
+				      width, height, format->width,
+				      format->height);
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		sel->r = *v4l2_subdev_state_get_crop(state, 0);
+		return 0;
+
+	case V4L2_SEL_TGT_NATIVE_SIZE:
+		sel->r.top = 0;
+		sel->r.left = 0;
+		sel->r.width = HM1246_NATIVE_WIDTH;
+		sel->r.height = HM1246_NATIVE_HEIGHT;
+		return 0;
+
+	case V4L2_SEL_TGT_CROP_DEFAULT:
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+		sel->r.top = mode->top;
+		sel->r.left = mode->left;
+		sel->r.width = mode->width;
+		sel->r.height = mode->height;
+		return 0;
+	}
+
+	return -EINVAL;
+}
+
+static int hm1246_init_state(struct v4l2_subdev *sd,
+			     struct v4l2_subdev_state *state)
+{
+	struct hm1246 *hm1246 = to_hm1246(sd);
+	struct v4l2_subdev_format fmt = {
+		.which = V4L2_SUBDEV_FORMAT_TRY,
+		.pad = 0,
+		.format = {
+			.code = hm1246_get_format_code(hm1246,
+						       &hm1246_modes[0]),
+			.width = hm1246_modes[0].width,
+			.height = hm1246_modes[0].height,
+		},
+	};
+
+	hm1246_set_format(sd, state, &fmt);
+
+	return 0;
+}
+
+static int hm1246_calc_pll(u32 xclk, u32 link_freq, u32 clocks_per_pixel,
+			   u8 *pll1, u8 *pll2, u8 *pll3)
+{
+	const u8 pclk_div_table[] = { 4, 5, 6, 7, 8, 12, 14, 16 };
+	const u8 sysclk_div_table[] = { 1, 2, 3, 4 };
+	const u8 post_div_table[] = { 1, 2, 4, 8 };
+	const int sysclk_pclk_ratio = 3; /* Recommended value */
+	u32 pclk, vco_out;
+	int pclk_div_index, sysclk_div_index, post_div_index;
+	bool sysclk_pclk_ratio_found = false;
+
+	if (link_freq < HM1246_PCLK_MIN || link_freq > HM1246_PCLK_MAX)
+		return -EINVAL;
+
+	/*
+	 * In raw mode (1 pixel per clock) the pixel clock is internally
+	 * divided by two.
+	 */
+	pclk = 2 * link_freq / clocks_per_pixel;
+
+	/* Find suitable PCLK and SYSCLK dividers. */
+	for (pclk_div_index = 0; pclk_div_index < ARRAY_SIZE(pclk_div_table);
+	     pclk_div_index++) {
+		for (sysclk_div_index = 0;
+		     sysclk_div_index < ARRAY_SIZE(sysclk_div_table);
+		     sysclk_div_index++) {
+			if (sysclk_div_table[sysclk_div_index] *
+				    sysclk_pclk_ratio ==
+			    pclk_div_table[pclk_div_index]) {
+				sysclk_pclk_ratio_found = true;
+				break;
+			}
+		}
+		if (sysclk_pclk_ratio_found)
+			break;
+	}
+
+	if (!sysclk_pclk_ratio_found)
+		return -EINVAL;
+
+	/* Determine an appropriate post divider. */
+	for (post_div_index = 0; post_div_index < ARRAY_SIZE(post_div_table);
+	     post_div_index++) {
+		vco_out = pclk * pclk_div_table[pclk_div_index] *
+			  post_div_table[post_div_index];
+
+		if (vco_out >= HM1246_PLL_VCO_MIN &&
+		    vco_out <= HM1246_PLL_VCO_MAX)
+			break;
+	}
+	if (post_div_index >= ARRAY_SIZE(post_div_table))
+		return -EINVAL;
+
+	/* Find pre-divider and multiplier values. */
+	for (u32 div = DIV_ROUND_UP(xclk, HM1246_PLL_INCLK_MAX);
+	     div <= xclk / HM1246_PLL_INCLK_MIN; div++) {
+		u32 multi, multi_h, multi_l, vco;
+
+		multi = DIV_ROUND_CLOSEST_ULL((u64)vco_out * div, xclk);
+		if (multi < HM1246_PLL_MULTI_MIN ||
+		    multi > HM1246_PLL_MULTI_MAX)
+			continue;
+
+		multi_h = multi / (HM1246_PLL_MULTI_H_MIN *
+				   HM1246_PLL_MULTI_L_MAX) +
+			  2;
+		multi_l = multi / multi_h;
+		vco = div_u64((u64)xclk * multi_h * multi_l, div);
+
+		if (vco != vco_out)
+			continue;
+
+		if (pll1 && pll2 && pll3) {
+			*pll1 = HM1246_PLL1CFG_MULTIPLIER(multi_l - 1);
+			*pll2 = HM1246_PLL2CFG_PRE_DIV(div - 1) |
+				HM1246_PLL2CFG_MULTIPLIER(multi_h - 2);
+			*pll3 = HM1246_PLL3CFG_POST_DIV(post_div_index) |
+				HM1246_PLL3CFG_SYSCLK_DIV(sysclk_div_index) |
+				HM1246_PLL3CFG_PCLK_DIV(pclk_div_index);
+		}
+
+		return 0;
+	}
+
+	return -EINVAL;
+}
+
+static int hm1246_cci_write_pll(struct hm1246 *hm1246, u8 pll1, u8 pll2,
+				u8 pll3)
+{
+	const struct cci_reg_sequence pll_regs[] = {
+		{ HM1246_PLL1CFG_REG, pll1 },
+		{ HM1246_PLL2CFG_REG, pll2 },
+		{ HM1246_PLL3CFG_REG, pll3 },
+		{ HM1246_SBC_CTRL_REG, HM1246_SBC_CTRL_PLL_EN },
+	};
+
+	return cci_multi_reg_write(hm1246->regmap, pll_regs,
+				   ARRAY_SIZE(pll_regs), NULL);
+}
+
+static int hm1246_pll_check_locked(struct hm1246 *hm1246)
+{
+	u64 boot_ref2;
+	int ret;
+
+	ret = cci_read(hm1246->regmap, HM1246_SBC_BOOT_REF2_REG, &boot_ref2,
+		       NULL);
+	if (ret)
+		return ret;
+
+	return (boot_ref2 & HM1246_SBC_BOOT_REF2_PLL_LOCK) ? 0 : -EIO;
+}
+
+static int hm1246_setup_pll(struct hm1246 *hm1246,
+			    const struct hm1246_mode *mode)
+{
+	u8 pll1, pll2, pll3;
+	int ret;
+
+	ret = hm1246_calc_pll(hm1246->xclk_freq, hm1246->link_frequency,
+			      mode->clocks_per_pixel, &pll1, &pll2, &pll3);
+	if (ret)
+		return ret;
+
+	ret = hm1246_cci_write_pll(hm1246, pll1, pll2, pll3);
+	if (ret)
+		return ret;
+
+	/* PLL lock time (tpll): 100us (typical) */
+	fsleep(200);
+
+	return hm1246_pll_check_locked(hm1246);
+}
+
+static int hm1246_cci_write_test_pattern(struct hm1246 *hm1246, u8 mode, u16 r,
+					 u16 g, u16 b)
+{
+	const struct cci_reg_sequence tpg_enable_regs[] = {
+		{ HM1246_TEST_DATA_RED_REG, r },
+		{ HM1246_TEST_DATA_GR_REG, g },
+		{ HM1246_TEST_DATA_GB_REG, g },
+		{ HM1246_TEST_DATA_BLUE_REG, b },
+		{ HM1246_TEST_PATTERN_MODE_REG, mode },
+	};
+
+	return cci_multi_reg_write(hm1246->regmap, tpg_enable_regs,
+				   ARRAY_SIZE(tpg_enable_regs), NULL);
+}
+
+static int hm1246_test_pattern(struct hm1246 *hm1246, u32 index)
+{
+	const u16 RGBMIN = 0, RGBMAX = 0x3ff;
+	const struct tp {
+		int pattern;
+		u16 r, g, b;
+	} tps[] = {
+		/* Disabled */
+		[0] = { .pattern = 0, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Checkboard pattern */
+		[1] = { .pattern = 0, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Ramp */
+		[2] = { .pattern = 1, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Moving ones */
+		[3] = { .pattern = 2, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Blending color bars */
+		[4] = { .pattern = 3, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Color bars */
+		[5] = { .pattern = 4, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Solid white */
+		[6] = { .pattern = 15, .r = RGBMAX, .g = RGBMAX, .b = RGBMAX },
+		/* Solid black */
+		[7] = { .pattern = 15, .r = RGBMIN, .g = RGBMIN, .b = RGBMIN },
+		/* Solid red */
+		[8] = { .pattern = 15, .r = RGBMAX, .g = RGBMIN, .b = RGBMIN },
+		/* Solid green */
+		[9] = { .pattern = 15, .r = RGBMIN, .g = RGBMAX, .b = RGBMIN },
+		/* Solid blue */
+		[10] = { .pattern = 15, .r = RGBMIN, .g = RGBMIN, .b = RGBMAX },
+	};
+	u8 mode;
+
+	if (index >= ARRAY_SIZE(tps))
+		return -EINVAL;
+
+	mode = HM1246_TEST_PATTERN_MODE_MODE(tps[index].pattern);
+	if (index)
+		mode |= HM1246_TEST_PATTERN_MODE_ENABLE;
+
+	return hm1246_cci_write_test_pattern(hm1246, mode, tps[index].r,
+					     tps[index].g, tps[index].b);
+}
+
+static int hm1246_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct hm1246 *hm1246 =
+		container_of_const(ctrl->handler, struct hm1246, ctrls);
+	struct v4l2_subdev_state *state;
+	const struct v4l2_mbus_framefmt *format;
+	u32 val;
+	bool needs_cmu_update = true;
+	int ret = 0;
+
+	state = v4l2_subdev_get_locked_active_state(&hm1246->sd);
+	format = v4l2_subdev_state_get_format(state, 0);
+
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		s64 exposure_max;
+
+		exposure_max =
+			format->height + ctrl->val - HM1246_COARSE_INTG_MARGIN;
+		ret = __v4l2_ctrl_modify_range(hm1246->exposure_ctrl,
+					       hm1246->exposure_ctrl->minimum,
+					       exposure_max,
+					       hm1246->exposure_ctrl->step,
+					       exposure_max);
+
+		if (ret) {
+			dev_err(hm1246->dev, "exposure ctrl range update failed\n");
+			return ret;
+		}
+	}
+
+	if (!pm_runtime_get_if_active(hm1246->dev))
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_EXPOSURE:
+		cci_write(hm1246->regmap, HM1246_COARSE_INTG_REG, ctrl->val,
+			  &ret);
+		break;
+
+	case V4L2_CID_ANALOGUE_GAIN:
+		cci_write(hm1246->regmap, HM1246_ANALOG_GLOBAL_GAIN_REG,
+			  ctrl->val, &ret);
+		break;
+
+	case V4L2_CID_VBLANK:
+		val = format->height + ctrl->val;
+		cci_write(hm1246->regmap, HM1246_FRAME_LENGTH_LINES_REG, val,
+			  &ret);
+		break;
+
+	case V4L2_CID_HFLIP:
+	case V4L2_CID_VFLIP:
+		val = 0;
+		if (hm1246->hflip_ctrl->val)
+			val |= HM1246_IMAGE_ORIENTATION_HFLIP;
+		if (hm1246->vflip_ctrl->val)
+			val |= HM1246_IMAGE_ORIENTATION_VFLIP;
+
+		cci_write(hm1246->regmap, HM1246_IMAGE_ORIENTATION_REG, val,
+			  &ret);
+		break;
+
+	case V4L2_CID_TEST_PATTERN:
+		ret = hm1246_test_pattern(hm1246, ctrl->val);
+		needs_cmu_update = false;
+		break;
+
+	default:
+		ret = -EINVAL;
+		needs_cmu_update = false;
+		break;
+	}
+
+	if (needs_cmu_update)
+		cci_write(hm1246->regmap, HM1246_CMU_UPDATE_REG, 0, &ret);
+
+	pm_runtime_put(hm1246->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops hm1246_ctrl_ops = {
+	.s_ctrl = hm1246_set_ctrl,
+};
+
+static int hm1246_identify_module(struct hm1246 *hm1246)
+{
+	u64 model_id;
+	int ret;
+
+	if (hm1246->identified)
+		return 0;
+
+	ret = cci_read(hm1246->regmap, HM1246_MODEL_ID_REG, &model_id, NULL);
+	if (ret)
+		return ret;
+
+	if (model_id != HM1246_MODEL_ID) {
+		dev_err(hm1246->dev, "model id mismatch: 0x%llx!=0x%x\n",
+			model_id, HM1246_MODEL_ID);
+		return -ENXIO;
+	}
+
+	hm1246->identified = true;
+
+	return 0;
+}
+
+static int hm1246_setup_moderegs(struct hm1246 *hm1246,
+				 const struct hm1246_mode *mode)
+{
+	const struct hm1246_reg_list *reg_list = &mode->reg_list;
+	const struct cci_reg_sequence modeaw[] = {
+		{ HM1246_X_ADDR_START_REG, mode->left },
+		{ HM1246_Y_ADDR_START_REG, mode->top },
+		{ HM1246_X_ADDR_END_REG, mode->width - 1 },
+		{ HM1246_Y_ADDR_END_REG, mode->height - 1 },
+		{ HM1246_DWIN_XOFFSET_REG, mode->left },
+		{ HM1246_DWIN_YOFFSET_REG, mode->top },
+		{ HM1246_DWIN_XSIZE_REG, mode->width },
+		{ HM1246_DWIN_YSIZE_REG, mode->height },
+		{ HM1246_LINE_LENGTH_PCK_REG, mode->hts },
+	};
+	int ret = 0;
+
+	cci_multi_reg_write(hm1246->regmap, modeaw, ARRAY_SIZE(modeaw), &ret);
+	cci_multi_reg_write(hm1246->regmap, reg_list->regs,
+			    reg_list->num_of_regs, &ret);
+
+	return ret;
+}
+
+static int hm1246_setup_bus(struct hm1246 *hm1246)
+{
+	u64 polarity_ctrl = 0, pclk_ctrl = 0;
+	int ret = 0;
+
+	if (hm1246->mbus_flags & V4L2_MBUS_HSYNC_ACTIVE_LOW)
+		polarity_ctrl |= HM1246_POLARITY_CTRL_HSYNC;
+
+	if (hm1246->mbus_flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
+		polarity_ctrl |= HM1246_POLARITY_CTRL_VSYNC;
+
+	cci_write(hm1246->regmap, HM1246_POLARITY_CTRL_REG, polarity_ctrl,
+		  &ret);
+
+	/*
+	 * If the clock output polarity flag PCLK_CTRL[3] is set (high), the
+	 * data lines change state on the falling edge of PCLK and should
+	 * therefore be sampled on the rising edge.
+	 * This is different than described in the data sheet.
+	 */
+	if (hm1246->mbus_flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
+		pclk_ctrl |= HM1246_PCLK_CTRL_POL;
+
+	cci_write(hm1246->regmap, HM1246_PCLK_CTRL_REG, pclk_ctrl, &ret);
+
+	return ret;
+}
+
+static int hm1246_enable_streams(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_state *state, u32 pad,
+				 u64 streams_mask)
+{
+	struct hm1246 *hm1246 = to_hm1246(sd);
+	const struct v4l2_mbus_framefmt *format;
+	const struct hm1246_mode *mode;
+	int ret;
+
+	format = v4l2_subdev_state_get_format(state, 0);
+	mode = v4l2_find_nearest_size(hm1246_modes, ARRAY_SIZE(hm1246_modes),
+				      width, height, format->width,
+				      format->height);
+
+	ret = pm_runtime_resume_and_get(hm1246->dev);
+	if (ret)
+		return ret;
+
+	ret = hm1246_identify_module(hm1246);
+	if (ret)
+		goto err_rpm_put;
+
+	ret = hm1246_setup_pll(hm1246, mode);
+	if (ret) {
+		dev_err(hm1246->dev, "failed to setup PLL\n");
+		goto err_rpm_put;
+	}
+
+	ret = hm1246_setup_moderegs(hm1246, mode);
+	if (ret)
+		goto err_rpm_put;
+
+	ret = hm1246_setup_bus(hm1246);
+	if (ret)
+		goto err_rpm_put;
+
+	ret = __v4l2_ctrl_handler_setup(&hm1246->ctrls);
+	if (ret) {
+		dev_err(hm1246->dev, "failed to setup v4l2 controls\n");
+		goto err_rpm_put;
+	}
+
+	ret = cci_write(hm1246->regmap, HM1246_MODE_SELECT_REG,
+			HM1246_MODE_SELECT_STREAM, NULL);
+	if (ret)
+		goto err_rpm_put;
+
+	/*
+	 * Since mirroring may change the actual pixel format, it must not be
+	 * changed during streaming.
+	 */
+	__v4l2_ctrl_grab(hm1246->vflip_ctrl, true);
+	__v4l2_ctrl_grab(hm1246->hflip_ctrl, true);
+
+	return 0;
+
+err_rpm_put:
+	pm_runtime_put_autosuspend(hm1246->dev);
+
+	return ret;
+}
+
+static int hm1246_disable_streams(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_state *state, u32 pad,
+				  u64 streams_mask)
+{
+	struct hm1246 *hm1246 = to_hm1246(sd);
+	int ret;
+
+	ret = cci_write(hm1246->regmap, HM1246_MODE_SELECT_REG,
+			HM1246_MODE_SELECT_STANDBY, NULL);
+
+	__v4l2_ctrl_grab(hm1246->vflip_ctrl, false);
+	__v4l2_ctrl_grab(hm1246->hflip_ctrl, false);
+
+	pm_runtime_put_autosuspend(hm1246->dev);
+
+	return ret;
+}
+
+static const struct v4l2_subdev_video_ops hm1246_video_ops = {
+	.s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops hm1246_subdev_pad_ops = {
+	.enum_mbus_code = hm1246_enum_mbus_code,
+	.enum_frame_size = hm1246_enum_frame_size,
+	.get_fmt = v4l2_subdev_get_fmt,
+	.set_fmt = hm1246_set_format,
+	.get_selection = hm1246_get_selection,
+	.enable_streams = hm1246_enable_streams,
+	.disable_streams = hm1246_disable_streams,
+};
+
+static const struct v4l2_subdev_ops hm1246_subdev_ops = {
+	.video = &hm1246_video_ops,
+	.pad = &hm1246_subdev_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops hm1246_internal_ops = {
+	.init_state = hm1246_init_state,
+};
+
+static int hm1246_get_regulators(struct device *dev, struct hm1246 *hm1246)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(hm1246_supply_names); i++)
+		hm1246->supplies[i].supply = hm1246_supply_names[i];
+
+	return devm_regulator_bulk_get(dev, ARRAY_SIZE(hm1246_supply_names),
+				       hm1246->supplies);
+}
+
+static int hm1246_parse_fwnode(struct hm1246 *hm1246)
+{
+	struct fwnode_handle *endpoint;
+	struct v4l2_fwnode_endpoint bus_cfg = {
+		.bus_type = V4L2_MBUS_PARALLEL,
+	};
+	int ret;
+
+	endpoint = fwnode_graph_get_endpoint_by_id(dev_fwnode(hm1246->dev),
+						   0, 0,
+						   FWNODE_GRAPH_ENDPOINT_NEXT);
+	if (!endpoint)
+		return dev_err_probe(hm1246->dev, -EINVAL,
+				     "missing endpoint node\n");
+
+	ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &bus_cfg);
+	fwnode_handle_put(endpoint);
+	if (ret)
+		return dev_err_probe(hm1246->dev, ret,
+				     "parsing endpoint node failed\n");
+
+	hm1246->mbus_flags = bus_cfg.bus.parallel.flags;
+
+	if (bus_cfg.nr_of_link_frequencies == 1)
+		hm1246->link_frequency = bus_cfg.link_frequencies[0];
+
+	v4l2_fwnode_endpoint_free(&bus_cfg);
+
+	if (!hm1246->link_frequency)
+		return dev_err_probe(hm1246->dev, -EINVAL,
+				     "one link frequency expected\n");
+
+	return 0;
+}
+
+static int hm1246_init_controls(struct hm1246 *hm1246)
+{
+	const struct hm1246_mode *mode = &hm1246_modes[0];
+	struct v4l2_fwnode_device_properties props;
+	struct v4l2_ctrl_handler *ctrl_hdlr = &hm1246->ctrls;
+	struct v4l2_ctrl *ctrl;
+	s64 pixel_rate, exposure_max, vblank_min, hblank;
+	int ret;
+
+	ret = v4l2_fwnode_device_parse(hm1246->dev, &props);
+	if (ret)
+		return ret;
+
+	v4l2_ctrl_handler_init(ctrl_hdlr, 11);
+
+	hm1246->hflip_ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops,
+					       V4L2_CID_HFLIP, 0, 1, 1, 0);
+	if (hm1246->hflip_ctrl)
+		hm1246->hflip_ctrl->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
+
+	hm1246->vflip_ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops,
+					       V4L2_CID_VFLIP, 0, 1, 1, 0);
+	if (hm1246->vflip_ctrl)
+		hm1246->vflip_ctrl->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
+
+	v4l2_ctrl_cluster(2, &hm1246->hflip_ctrl);
+
+	ctrl = v4l2_ctrl_new_int_menu(ctrl_hdlr, &hm1246_ctrl_ops,
+				      V4L2_CID_LINK_FREQ,
+				      0, 0,
+				      &hm1246->link_frequency);
+	if (ctrl)
+		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	pixel_rate = div_u64(hm1246->link_frequency, mode->clocks_per_pixel);
+	ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops,
+				 V4L2_CID_PIXEL_RATE,
+				 pixel_rate, pixel_rate, 1,
+				 pixel_rate);
+
+	vblank_min = mode->vts_min - mode->height;
+	ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops,
+				 V4L2_CID_VBLANK, vblank_min,
+				 HM1246_VTS_MAX - mode->height,
+				 1, vblank_min);
+
+	hblank = mode->hts - mode->width;
+	ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops,
+				 V4L2_CID_HBLANK, hblank, hblank,
+				 1, hblank);
+	if (ctrl)
+		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+			  HM1246_ANALOG_GLOBAL_GAIN_MIN,
+			  HM1246_ANALOG_GLOBAL_GAIN_MAX,
+			  HM1246_ANALOG_GLOBAL_GAIN_STEP,
+			  HM1246_ANALOG_GLOBAL_GAIN_MIN);
+
+	exposure_max = mode->vts_min - HM1246_COARSE_INTG_MARGIN;
+	hm1246->exposure_ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &hm1246_ctrl_ops,
+						  V4L2_CID_EXPOSURE,
+						  HM1246_COARSE_INTG_MIN,
+						  exposure_max,
+						  HM1246_COARSE_INTG_STEP,
+						  exposure_max);
+
+	v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &hm1246_ctrl_ops,
+				     V4L2_CID_TEST_PATTERN,
+				     ARRAY_SIZE(hm1246_test_pattern_menu) - 1,
+				     0, 0, hm1246_test_pattern_menu);
+
+	v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &hm1246_ctrl_ops, &props);
+
+	if (ctrl_hdlr->error) {
+		v4l2_ctrl_handler_free(ctrl_hdlr);
+		return ctrl_hdlr->error;
+	}
+
+	hm1246->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+}
+
+static int hm1246_probe(struct i2c_client *client)
+{
+	struct hm1246 *hm1246;
+	int ret;
+
+	hm1246 = devm_kzalloc(&client->dev, sizeof(*hm1246), GFP_KERNEL);
+	if (!hm1246)
+		return -ENOMEM;
+
+	hm1246->dev = &client->dev;
+
+	ret = hm1246_parse_fwnode(hm1246);
+	if (ret)
+		return ret;
+
+	hm1246->regmap = devm_cci_regmap_init_i2c(client, 16);
+	if (IS_ERR(hm1246->regmap))
+		return dev_err_probe(hm1246->dev, PTR_ERR(hm1246->regmap),
+				     "failed to init CCI\n");
+
+	hm1246->xclk = devm_v4l2_sensor_clk_get(hm1246->dev, NULL);
+	if (IS_ERR(hm1246->xclk))
+		return dev_err_probe(hm1246->dev, PTR_ERR(hm1246->xclk),
+				     "failed to get xclk\n");
+
+	hm1246->xclk_freq = clk_get_rate(hm1246->xclk);
+	if (hm1246->xclk_freq < HM1246_XCLK_MIN ||
+	    hm1246->xclk_freq > HM1246_XCLK_MAX)
+		return dev_err_probe(hm1246->dev, -EINVAL,
+				     "xclk frequency out of range: %luHz\n",
+				     hm1246->xclk_freq);
+
+	for (unsigned int i = 0; i < ARRAY_SIZE(hm1246_modes); i++) {
+		ret = hm1246_calc_pll(hm1246->xclk_freq, hm1246->link_frequency,
+				      hm1246_modes[i].clocks_per_pixel,
+				      NULL, NULL, NULL);
+		if (ret)
+			return dev_err_probe(hm1246->dev, ret,
+					     "no PLL setup for %lld Hz\n",
+					     hm1246->link_frequency);
+	}
+
+	ret = hm1246_get_regulators(hm1246->dev, hm1246);
+	if (ret)
+		return dev_err_probe(hm1246->dev, ret,
+				     "failed to get regulators\n");
+
+	hm1246->reset_gpio =
+		devm_gpiod_get_optional(hm1246->dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(hm1246->reset_gpio))
+		return dev_err_probe(hm1246->dev, PTR_ERR(hm1246->reset_gpio),
+				     "failed to get reset GPIO\n");
+
+	v4l2_i2c_subdev_init(&hm1246->sd, client, &hm1246_subdev_ops);
+	hm1246->sd.internal_ops = &hm1246_internal_ops;
+
+	ret = hm1246_init_controls(hm1246);
+	if (ret)
+		return dev_err_probe(hm1246->dev, ret,
+				     "failed to init controls\n");
+
+	hm1246->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	hm1246->pad.flags = MEDIA_PAD_FL_SOURCE;
+	hm1246->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+
+	ret = media_entity_pads_init(&hm1246->sd.entity, 1, &hm1246->pad);
+	if (ret) {
+		dev_err_probe(hm1246->dev, ret, "failed to init media pads\n");
+		goto err_v4l2_ctrl_handler_free;
+	}
+
+	hm1246->sd.state_lock = hm1246->ctrls.lock;
+	ret = v4l2_subdev_init_finalize(&hm1246->sd);
+	if (ret) {
+		dev_err_probe(hm1246->dev, ret, "failed to init v4l2 subdev\n");
+		goto err_media_entity_cleanup;
+	}
+
+	pm_runtime_enable(hm1246->dev);
+	pm_runtime_set_autosuspend_delay(hm1246->dev, 1000);
+	pm_runtime_use_autosuspend(hm1246->dev);
+	pm_runtime_idle(hm1246->dev);
+
+	ret = v4l2_async_register_subdev_sensor(&hm1246->sd);
+	if (ret) {
+		dev_err_probe(hm1246->dev, ret,
+			      "failed to register v4l2 subdev\n");
+		goto err_subdev_cleanup;
+	}
+
+	return 0;
+
+err_subdev_cleanup:
+	v4l2_subdev_cleanup(&hm1246->sd);
+	pm_runtime_disable(hm1246->dev);
+	pm_runtime_set_suspended(hm1246->dev);
+
+err_media_entity_cleanup:
+	media_entity_cleanup(&hm1246->sd.entity);
+
+err_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(&hm1246->ctrls);
+
+	return ret;
+}
+
+static void hm1246_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hm1246 *hm1246 = to_hm1246(sd);
+
+	v4l2_async_unregister_subdev(&hm1246->sd);
+	v4l2_subdev_cleanup(sd);
+	media_entity_cleanup(&hm1246->sd.entity);
+	v4l2_ctrl_handler_free(&hm1246->ctrls);
+
+	pm_runtime_disable(&client->dev);
+	if (!pm_runtime_status_suspended(&client->dev)) {
+		hm1246_power_off(hm1246->dev);
+		pm_runtime_set_suspended(&client->dev);
+	}
+}
+
+static const struct of_device_id hm1246_of_match[] = {
+	{ .compatible = "himax,hm1246" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, hm1246_of_match);
+
+static DEFINE_RUNTIME_DEV_PM_OPS(hm1246_pm_ops,
+				 hm1246_power_off, hm1246_power_on, NULL);
+
+static struct i2c_driver hm1246_i2c_driver = {
+	.driver = {
+		.of_match_table = hm1246_of_match,
+		.pm = pm_ptr(&hm1246_pm_ops),
+		.name = "hm1246",
+	},
+	.probe = hm1246_probe,
+	.remove = hm1246_remove,
+};
+module_i2c_driver(hm1246_i2c_driver);
+
+MODULE_DESCRIPTION("Himax HM1246 camera driver");
+MODULE_AUTHOR("Matthias Fend <matthias.fend@emfend.at>");
+MODULE_LICENSE("GPL");

-- 
2.34.1

Re: [PATCH v8 0/2] media: add Himax HM1246 image sensor

[Andy Shevchenko]

On Tue, Jan 13, 2026 at 10:07:25AM +0100, Matthias Fend wrote:

> this series adds support for the Himax HM1246 image sensor.
> The Himax HM1246-AWD is a 1/3.7-Inch CMOS image sensor SoC with an active
> array size of 1296 x 976.
> Currently, only the native RAW mode is supported. Other modes and the
> internal image signal processing pipeline are not currently supported.
> The data sheet is available on the manufacturer's website [1].
> Tested on i.MX8MP hardware. A Toshiba TC358746 bridge was used to convert
> the sensor's parallel video output into MIPI signals for the i.MX8MP.

Please, do not send a new version when we have been in the middle of the
discussion.

-- 
With Best Regards,
Andy Shevchenko