Re: [PATCH v1 2/2] media: i2c: mt9m114: add support for Aptina MI1040

[Sakari Ailus <sakari.ailus@linux.intel.com>]

Hi Svyatoslav,

Thanks for the patchset.

On Mon, Jan 26, 2026 at 10:34:30AM +0200, Svyatoslav Ryhel wrote:
> Slightly different version of MT9M114 camera module is used in a several
> devices like ASUS Nexus 7 (2012) or ASUS Transformer Prime TF201 and is
> called Aptina MI1040. Only difference found so far is lacking ability to

s/Only/The only/

> poll STATUS and COMMAND registers during power on sequence, which causes
> driver to fail with time out error. Add polling flag to diverge models and
> address quirk found in MI1040.
> 
> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
> ---
>  drivers/media/i2c/mt9m114.c | 35 ++++++++++++++++++++++++++++-------
>  1 file changed, 28 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/media/i2c/mt9m114.c b/drivers/media/i2c/mt9m114.c
> index 4ec033c0ee84..d96a57ebcad4 100644
> --- a/drivers/media/i2c/mt9m114.c
> +++ b/drivers/media/i2c/mt9m114.c
> @@ -368,6 +368,10 @@ enum {
>   * Data Structures
>   */
>  
> +struct mt9m114_model_info {
> +	bool polling;
> +};
> +
>  enum mt9m114_format_flag {
>  	MT9M114_FMT_FLAG_PARALLEL = BIT(0),
>  	MT9M114_FMT_FLAG_CSI2 = BIT(1),
> @@ -421,6 +425,8 @@ struct mt9m114 {
>  
>  		struct v4l2_ctrl *tpg[4];
>  	} ifp;
> +
> +	const struct mt9m114_model_info *info;
>  };
>  
>  /* -----------------------------------------------------------------------------
> @@ -2186,9 +2192,11 @@ static int mt9m114_power_on(struct mt9m114 *sensor)
>  	 */
>  	usleep_range(44500, 50000);
>  
> -	ret = mt9m114_poll_command(sensor, MT9M114_COMMAND_REGISTER_SET_STATE);
> -	if (ret < 0)
> -		goto error_clock;
> +	if (sensor->info->polling) {
> +		ret = mt9m114_poll_command(sensor, MT9M114_COMMAND_REGISTER_SET_STATE);
> +		if (ret < 0)
> +			goto error_clock;
> +	}

What does the datasheet say, is there a need to do something else instead?
As the polling is there to ensure firmware has done its job, the need
appears to still be there.

>  
>  	if (sensor->bus_cfg.bus_type == V4L2_MBUS_PARALLEL) {
>  		/*
> @@ -2207,9 +2215,11 @@ static int mt9m114_power_on(struct mt9m114 *sensor)
>  	 * reaches the standby mode (either initiated manually above in
>  	 * parallel mode, or automatically after reset in MIPI mode).
>  	 */
> -	ret = mt9m114_poll_state(sensor, MT9M114_SYS_STATE_STANDBY);
> -	if (ret < 0)
> -		goto error_clock;
> +	if (sensor->info->polling) {
> +		ret = mt9m114_poll_state(sensor, MT9M114_SYS_STATE_STANDBY);

Ditto.

> +		if (ret < 0)
> +			goto error_clock;
> +	}
>  
>  	return 0;
>  
> @@ -2421,6 +2431,8 @@ static int mt9m114_probe(struct i2c_client *client)
>  	if (ret < 0)
>  		return ret;
>  
> +	sensor->info = of_device_get_match_data(dev);

You can use device_get_match_data() here.

> +
>  	/* Acquire clocks, GPIOs and regulators. */
>  	sensor->clk = devm_v4l2_sensor_clk_get(dev, NULL);
>  	if (IS_ERR(sensor->clk)) {
> @@ -2539,8 +2551,17 @@ static void mt9m114_remove(struct i2c_client *client)
>  	pm_runtime_set_suspended(dev);
>  }
>  
> +static const struct mt9m114_model_info mt9m114_models_default = {
> +	.polling = true,
> +};
> +
> +static const struct mt9m114_model_info mt9m114_models_aptina = {
> +	.polling = false,
> +};
> +
>  static const struct of_device_id mt9m114_of_ids[] = {
> -	{ .compatible = "onnn,mt9m114" },
> +	{ .compatible = "onnn,mt9m114", .data = &mt9m114_models_default },
> +	{ .compatible = "aptina,mi1040", .data = &mt9m114_models_aptina },
>  	{ /* sentinel */ },

The sentinel entry shouldn't have a comma. Feel free to fix that while at
it.

>  };
>  MODULE_DEVICE_TABLE(of, mt9m114_of_ids);

-- 
Kind regards,

Sakari Ailus