From: Ritesh Harjani <riteshh@codeaurora.org>
To: Adrian Hunter <adrian.hunter@intel.com>,
ulf.hansson@linaro.org, linux-mmc@vger.kernel.org,
sboyd@codeaurora.org, andy.gross@linaro.org
Cc: shawn.lin@rock-chips.com, devicetree@vger.kernel.org,
linux-clk@vger.kernel.org, david.brown@linaro.org,
linux-arm-msm@vger.kernel.org, georgi.djakov@linaro.org,
alex.lemberg@sandisk.com, mateusz.nowak@intel.com,
Yuliy.Izrailov@sandisk.com, asutoshd@codeaurora.org,
david.griego@linaro.org, stummala@codeaurora.org,
venkatg@codeaurora.org, rnayak@codeaurora.org,
pramod.gurav@linaro.org, jeremymc@redhat.com
Subject: Re: [PATCH v8 09/16] mmc: sdhci: Factor out sdhci_enable_clock
Date: Mon, 21 Nov 2016 12:01:19 +0530 [thread overview]
Message-ID: <abed48c3-d220-e907-d482-dda074c72764@codeaurora.org> (raw)
In-Reply-To: <df833f0b-041f-67d1-4b91-ef4399ecf15c@intel.com>
On 11/18/2016 7:26 PM, Adrian Hunter wrote:
> On 16/11/16 18:00, Ritesh Harjani wrote:
>> Factor out sdhci_enable_clock from sdhci_set_clock
>> and make it EXPORT_SYMBOL so that it can be called.
>
> This seems fine apart from minor comments below.
>
>>
>> Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
>> ---
>> drivers/mmc/host/sdhci.c | 28 +++++++++++++++++-----------
>> drivers/mmc/host/sdhci.h | 1 +
>> 2 files changed, 18 insertions(+), 11 deletions(-)
>>
>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>> index d08d507..8a89d89 100644
>> --- a/drivers/mmc/host/sdhci.c
>> +++ b/drivers/mmc/host/sdhci.c
>> @@ -1344,20 +1344,10 @@ u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
>> }
>> EXPORT_SYMBOL_GPL(sdhci_calc_clk);
>>
>> -void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
>> +void sdhci_enable_clock(struct sdhci_host *host, unsigned short clk)
>
> We write a u16 so let's make clk a u16 instead of unsigned short.
Ok.
>
> I would have called it sdhci_enable_clk() to go with sdhci_calc_clk() and
> slightly different from sdhci_set_clock() which is a callback whereas the
> other 2 are helpers.
Sure, will make sdhci_enable_clk()
>
>> {
>> - u16 clk;
>> unsigned long timeout;
>>
>> - host->mmc->actual_clock = 0;
>> -
>> - sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
>> -
>> - if (clock == 0)
>> - return;
>> -
>> - clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
>> -
>> clk |= SDHCI_CLOCK_INT_EN;
>> sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
>>
>> @@ -1378,6 +1368,22 @@ void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
>> clk |= SDHCI_CLOCK_CARD_EN;
>> sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
>> }
>> +EXPORT_SYMBOL_GPL(sdhci_enable_clock);
>> +
>> +void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
>> +{
>> + u16 clk;
>> +
>> + host->mmc->actual_clock = 0;
>> +
>> + sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
>> +
>> + if (clock == 0)
>> + return;
>> +
>> + clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
>> + sdhci_enable_clock(host, clk);
>> +}
>> EXPORT_SYMBOL_GPL(sdhci_set_clock);
>>
>> static void sdhci_set_power_reg(struct sdhci_host *host, unsigned char mode,
>> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
>> index 766df17..8e77a3b 100644
>> --- a/drivers/mmc/host/sdhci.h
>> +++ b/drivers/mmc/host/sdhci.h
>> @@ -681,6 +681,7 @@ static inline bool sdhci_sdio_irq_enabled(struct sdhci_host *host)
>> u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
>> unsigned int *actual_clock);
>> void sdhci_set_clock(struct sdhci_host *host, unsigned int clock);
>> +void sdhci_enable_clock(struct sdhci_host *host, unsigned short clk);
>> void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
>> unsigned short vdd);
>> void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
>>
>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2016-11-21 6:31 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-16 16:00 [PATCH v8 00/16] mmc: sdhci-msm: Add clk-rates, DDR, HS400 support Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 01/16] clk: qcom: Add rcg ops to return floor value closest to the requested rate Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 03/16] mmc: sdhci-msm: Change poor style writel/readl of registers Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 04/16] ARM: dts: Add xo_clock to sdhc nodes on qcom platforms Ritesh Harjani
2016-11-17 0:43 ` [PATCH v8 04/16] ARM: dts: Add xo to sdhc clock node " Ritesh Harjani
2016-11-18 3:56 ` Andy Gross
2016-11-21 6:30 ` Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 05/16] dt-bindings: sdhci-msm: Add xo_clock property Ritesh Harjani
2016-11-16 19:13 ` Stephen Boyd
2016-11-17 0:41 ` Ritesh Harjani
2016-11-17 0:47 ` [PATCH v8 05/16] dt-bindings: sdhci-msm: Add xo property Ritesh Harjani
2016-11-17 23:03 ` Stephen Boyd
[not found] ` <20161117230352.GO25626-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-21 6:31 ` Ritesh Harjani
[not found] ` <1479343623-31163-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-18 14:17 ` Rob Herring
2016-11-16 16:00 ` [PATCH v8 07/16] mmc: sdhci-msm: Add get_min_clock() and get_max_clock() callback Ritesh Harjani
[not found] ` <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-16 16:00 ` [PATCH v8 02/16] clk: qcom: Move all sdcc rcgs to use clk_rcg2_floor_ops Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 06/16] mmc: sdhci-msm: Update DLL reset sequence Ritesh Harjani
[not found] ` <1479312052-22396-7-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-17 0:50 ` Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 08/16] mmc: sdhci-msm: Enable few quirks Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 09/16] mmc: sdhci: Factor out sdhci_enable_clock Ritesh Harjani
2016-11-18 13:56 ` Adrian Hunter
2016-11-21 6:31 ` Ritesh Harjani [this message]
2016-11-16 16:00 ` [PATCH v8 10/16] mmc: sdhci-msm: Implement set_clock callback for sdhci-msm Ritesh Harjani
2016-11-18 14:14 ` Adrian Hunter
2016-11-16 16:00 ` [PATCH v8 12/16] arm64: dts: qcom: msm8916: Add ddr support to sdhc1 Ritesh Harjani
2016-11-17 0:52 ` Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 13/16] mmc: sdhci-msm: Add HS400 platform support Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 16/16] sdhci: sdhci-msm: update dll configuration Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 11/16] mmc: sdhci-msm: Add clock changes for DDR mode Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 14/16] mmc: sdhci-msm: Save the calculated tuning phase Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 15/16] mmc: sdhci-msm: Add calibration tuning for CDCLP533 circuit Ritesh Harjani
2016-11-17 0:08 ` [PATCH v8 00/16] mmc: sdhci-msm: Add clk-rates, DDR, HS400 support Jeremy McNicoll
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=abed48c3-d220-e907-d482-dda074c72764@codeaurora.org \
--to=riteshh@codeaurora.org \
--cc=Yuliy.Izrailov@sandisk.com \
--cc=adrian.hunter@intel.com \
--cc=alex.lemberg@sandisk.com \
--cc=andy.gross@linaro.org \
--cc=asutoshd@codeaurora.org \
--cc=david.brown@linaro.org \
--cc=david.griego@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=georgi.djakov@linaro.org \
--cc=jeremymc@redhat.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=mateusz.nowak@intel.com \
--cc=pramod.gurav@linaro.org \
--cc=rnayak@codeaurora.org \
--cc=sboyd@codeaurora.org \
--cc=shawn.lin@rock-chips.com \
--cc=stummala@codeaurora.org \
--cc=ulf.hansson@linaro.org \
--cc=venkatg@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).