Re: [PATCH v2 1/3] arm64: dts: qcom: kaanapali: Add USB support for Kaanapali SoC

Jingyi Wang
2026-03-30T02:52:21Z

On 3/30/2026 1:52 AM, Krishna Kurapati wrote:
> From: Ronak Raheja <ronak.raheja@oss.qualcomm.com>
>
> Add the base USB devicetree definitions for Kaanapali platform. The overall
> chipset contains a single DWC3 USB3 controller (rev. 200a), SS QMP PHY
> (rev. v8) and M31 eUSB2 PHY.
>
> Signed-off-by: Ronak Raheja <ronak.raheja@oss.qualcomm.com>
> Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
> Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
> ---
> arch/arm64/boot/dts/qcom/kaanapali.dtsi | 154 ++++++++++++++++++++++++
> 1 file changed, 154 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/kaanapali.dtsi b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
> index ac6a6c789902..08d7c1a1d829 100644
> --- a/arch/arm64/boot/dts/qcom/kaanapali.dtsi
> +++ b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
> @@ -6026,6 +6026,160 @@ pdp_tx: scp-sram-section@100 {
> reg = <0x100 0x80>;
> };
> };
> +
> + usb_hsphy: phy@88e3000 {
> + compatible = "qcom,kaanapali-m31-eusb2-phy",
> + "qcom,sm8750-m31-eusb2-phy";
> + reg = <0x0 0x88e3000 0x0 0x29c>;
> +
> + clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
> + clock-names = "ref";
> +
> + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> +
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + usb_dp_qmpphy: phy@88e8000 {
> + compatible = "qcom,kaanapali-qmp-usb3-dp-phy",
> + "qcom,sm8750-qmp-usb3-dp-phy";
> + reg = <0x0 0x088e8000 0x0 0x4000>;
> +
> + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> + <&tcsr TCSR_USB3_CLKREF_EN>,
> + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "aux",
> + "ref",
> + "com_aux",
> + "usb3_pipe";
> +
> + resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
> + <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
> + reset-names = "phy",
> + "common";
> +
> + power-domains = <&gcc GCC_USB3_PHY_GDSC>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <1>;
> +
> + orientation-switch;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_dp_qmpphy_out: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_dp_qmpphy_usb_ss_in: endpoint {
> + remote-endpoint = <&usb_dwc3_ss>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + usb_dp_qmpphy_dp_in: endpoint {
> + };
> + };
> + };
> + };
> +
> + usb: usb@a600000 {
> + compatible = "qcom,kaanapali-dwc3", "qcom,snps-dwc3";
> + reg = <0x0 0x0a600000 0x0 0xfc100>;
> +
> + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
> + <&gcc GCC_USB30_PRIM_MASTER_CLK>,
> + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
> + <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
> + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
> + clock-names = "cfg_noc",
> + "core",
> + "iface",
> + "sleep",
> + "mock_utmi";
> +
> + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB30_PRIM_MASTER_CLK>;
> + assigned-clock-rates = <19200000>, <200000000>;
> +
> + interrupts-extended = <&intc GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
> + <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> + <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
> + <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
> + <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
> + <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "dwc_usb3",
> + "pwr_event",
> + "hs_phy_irq",
> + "dp_hs_phy_irq",
> + "dm_hs_phy_irq",
> + "ss_phy_irq";
> +
> + power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
> + required-opps = <&rpmhpd_opp_nom>;
> +
> + resets = <&gcc GCC_USB30_PRIM_BCR>;
> +
> + interconnects = <&aggre_noc MASTER_USB3 QCOM_ICC_TAG_ALWAYS
> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
> + &config_noc SLAVE_USB3 QCOM_ICC_TAG_ACTIVE_ONLY>;
> + interconnect-names = "usb-ddr", "apps-usb";
> + iommus = <&apps_smmu 0x40 0x0>;
> +
> + phys = <&usb_hsphy>, <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
> + phy-names = "usb2-phy", "usb3-phy";
> +
> + snps,hird-threshold = /bits/ 8 <0x0>;
> + snps,usb2-gadget-lpm-disable;
> + snps,dis_u2_susphy_quirk;
> + snps,dis_enblslpm_quirk;
> + snps,dis-u1-entry-quirk;
> + snps,dis-u2-entry-quirk;
> + snps,is-utmi-l1-suspend;
> + snps,usb3_lpm_capable;
> + snps,usb2-lpm-disable;
> + snps,has-lpm-erratum;
> + tx-fifo-resize;
> + dma-coherent;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_dwc3_ss: endpoint {
> + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
> + };
> + };
> + };
> + };

please make sure the nodes are sorted in address order.

Thanks,
Jingyi

> };
>
> thermal-zones {