Re: [PATCH v3 2/3] media: i2c: add os02g10 image sensor driver

["sakari.ailus@linux.intel.com" <sakari.ailus@linux.intel.com>]

Hi Elgin, Vladimir,

On Thu, Jun 18, 2026 at 06:22:14AM +0000, Elgin Perumbilly wrote:
> Hi Vladimir,
>  
> Thank you for the review.
>  
> I have addressed all of the comments except for two, where I am not entirely
> sure about the requested changes. Could you please take a look at the points
> below and let me know your opinion?
>  
> > On 4/24/26 12:25, Elgin Perumbilly wrote:
> > > Add a v4l2 subdevice driver for the Omnivision os02g10 sensor.
> > >
> > > The Omnivision os02g10 is a CMOS image sensor with an active array size of
> > > 1920 x 1080.
> > >
> > > The following features are supported:
> > > - Manual exposure an gain control support
> > > - vblank/hblank control support
> > > - vflip/hflip control support
> > > - Test pattern control support
> > > - Supported resolution: 1920 x 1080 @ 30fps (SBGGR10)
> > >
> > > Signed-off-by: Elgin Perumbilly <elgin.perumbilly@siliconsignals.io>
> > > Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
>  
> ...
>  
> > > +#include <linux/array_size.h>
> > > +#include <linux/bitops.h>
> > > +#include <linux/cleanup.h>
> > > +#include <linux/clk.h>
> > > +#include <linux/container_of.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/err.h>
> > > +#include <linux/gpio/consumer.h>
> > > +#include <linux/i2c.h>
> > > +#include <linux/module.h>
> > > +#include <linux/mutex.h>
> > > +#include <linux/pm_runtime.h>
> > > +#include <linux/property.h>
> > > +#include <linux/regulator/consumer.h>
> > > +#include <linux/units.h>
> > > +#include <linux/types.h>
> > > +#include <linux/time.h>
> > > +#include <linux/regmap.h>
> >
> > Please sort the list of includes in alphabetical order, also you
> > may consider to shrink the list by removing quite many inherited
> > includes.
>  
> Some maintainers prefer the "include what you use" approach, like Andy,
> so I added all the headers that are directly used. Should I now remove
> any inherited includes?

Andy has been indeed asking to include what you use; this way cleaning up
the headers in the future becomes possible.

>  
> > > +#include <media/v4l2-cci.h>
> > > +#include <media/v4l2-ctrls.h>
> > > +#include <media/v4l2-device.h>
> > > +#include <media/v4l2-fwnode.h>
> > > +#include <media/v4l2-mediabus.h>
>  
> ...
>  
> > > +static int os02g10_set_framefmt(struct os02g10 *os02g10,
> > > +                             struct v4l2_subdev_state *state)
> > > +{
> > > +     const struct v4l2_mbus_framefmt *format;
> > > +     const struct os02g10_mode *mode;
> > > +     int ret = 0;
> > > +
> > > +     format = v4l2_subdev_state_get_format(state, 0);
> > > +     mode = v4l2_find_nearest_size(supported_modes,
> > > +                                   ARRAY_SIZE(supported_modes), width,
> > > +                                   height, format->width, format->height);
> > > +
> > > +     cci_write(os02g10->cci, OS02G10_REG_V_START, mode->y_start, &ret);
> > > +     cci_write(os02g10->cci, OS02G10_REG_V_SIZE, mode->height, &ret);
> > > +     cci_write(os02g10->cci, OS02G10_REG_V_SIZE_MIPI, mode->height, &ret);
> > > +     cci_write(os02g10->cci, OS02G10_REG_H_START, mode->x_start, &ret);
> > > +     cci_write(os02g10->cci, OS02G10_REG_H_SIZE, mode->width, &ret);
> > > +     cci_write(os02g10->cci, OS02G10_REG_H_SIZE_MIPI, mode->width, &ret);
> > > +
> > > +     return ret;
> >
> > Just "return 0" here, and remove the local variable.
>  
> Could you clarify why this should return 0? The local ret is passed to all
> cci_write() calls so that any write error is propagated. Returning 0 here
> would appear to suppress those errors and always report success.

The code seems fine to me.

-- 
Regards,

Sakari Ailus