Re: [PATCH] mmc: usdhi6rol0: remove driver

[Jesper Nilsson <jesper.nilsson@axis.com>]

On Wed, Nov 11, 2026 at 01:34:52PM +0100, Wolfram Sang wrote
> In 2019, Yamada-san already tried to delete this driver because no user
> was known. Lars revealed that it was used on Axis ARM32 Artpec-6 chips
> which they planned to use for another 5 years[1]. We agreed that this
> driver should be merged into the main SDHI driver and, for the time
> being, added a MAINTAINERS entry to make the connection to Axis.
> 
> Now, in 2026, the 5 years are more than over, and the merge to the main
> driver did not happen. Nor an addition of a SDHI device node to the only
> Artpec-6 DTS file. So, regarding upstream, this driver is still unused.
> To remove maintenance burden, let's remove it for good.
> 
> [1] https://lore.kernel.org/r/CADnJP=sg1Kp=TAvUD-ofQje9Y6mWWE_ZnQM_eB85uw3z6PHrVQ@mail.gmail.com
> 
> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
> [wsa: rebased, bring commit msg into 2026]
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Cc: Jesper Nilsson <jesper.nilsson@axis.com>

Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>

> Cc: Lars Persson <lars.persson@axis.com>
> ---
> 
> Jesper, Lars: please speak up if you disagree.
> 
>  .../devicetree/bindings/mmc/usdhi6rol0.txt    |   39 -
>  MAINTAINERS                                   |    1 -
>  drivers/mmc/host/Kconfig                      |    7 -
>  drivers/mmc/host/Makefile                     |    1 -
>  drivers/mmc/host/usdhi6rol0.c                 | 1904 -----------------
>  5 files changed, 1952 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/mmc/usdhi6rol0.txt
>  delete mode 100644 drivers/mmc/host/usdhi6rol0.c
> 
> diff --git a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt
> deleted file mode 100644
> index 6d1b7971d078..000000000000
> --- a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt
> +++ /dev/null
> @@ -1,39 +0,0 @@
> -* Renesas usdhi6rol0 SD/SDIO host controller
> -
> -Required properties:
> -
> -- compatible:	must be
> -		"renesas,usdhi6rol0"
> -- interrupts:	3 interrupts, named "card detect", "data" and "SDIO" must be
> -		specified
> -- clocks:	a clock binding for the IMCLK input
> -
> -Optional properties:
> -
> -- vmmc-supply:	a phandle of a regulator, supplying Vcc to the card
> -- vqmmc-supply:	a phandle of a regulator, supplying VccQ to the card
> -- pinctrl-names: Can contain a "default" entry and a "state_uhs"
> -                 entry. The state_uhs entry is used together with the default
> -                 entry when the board requires distinct settings for UHS speeds.
> -
> -- pinctrl-N: One property for each name listed in pinctrl-names, see
> -             ../pinctrl/pinctrl-bindings.txt.
> -
> -Additionally any standard mmc bindings from mmc.txt can be used.
> -
> -Example:
> -
> -sd0: sd@ab000000 {
> -	compatible = "renesas,usdhi6rol0";
> -	reg = <0xab000000 0x200>;
> -	interrupts = <0 23 0x4
> -		      0 24 0x4
> -		      0 25 0x4>;
> -	interrupt-names = "card detect", "data", "SDIO";
> -	bus-width = <4>;
> -	max-frequency = <50000000>;
> -	cap-power-off-card;
> -	clocks = <&imclk>;
> -	vmmc-supply = <&vcc_sd0>;
> -	vqmmc-supply = <&vccq_sd0>;
> -};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 986e23fcb020..16e533e9c684 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2810,7 +2810,6 @@ F:	arch/arm/boot/dts/axis/
>  F:	arch/arm/mach-artpec
>  F:	drivers/clk/axis
>  F:	drivers/crypto/axis
> -F:	drivers/mmc/host/usdhi6rol0.c
>  F:	drivers/pinctrl/pinctrl-artpec*
>  
>  ARM/ASPEED I2C DRIVER
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 79bfc425e7c7..4352fc95cce2 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -942,13 +942,6 @@ config MMC_WMT
>  	  To compile this driver as a module, choose M here: the
>  	  module will be called wmt-sdmmc.
>  
> -config MMC_USDHI6ROL0
> -	tristate "Renesas USDHI6ROL0 SD/SDIO Host Controller support"
> -	depends on HAS_DMA
> -	help
> -	  This selects support for the Renesas USDHI6ROL0 SD/SDIO
> -	  Host Controller
> -
>  config MMC_REALTEK_PCI
>  	tristate "Realtek PCI-E SD/MMC Card Interface Driver"
>  	depends on MISC_RTSX_PCI
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index fd043afab57e..43100a3185a3 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -68,7 +68,6 @@ obj-$(CONFIG_MMC_MESON_MX_SDHC)	+= meson-mx-sdhc.o
>  obj-$(CONFIG_MMC_MESON_MX_SDIO)	+= meson-mx-sdio.o
>  obj-$(CONFIG_MMC_MOXART)	+= moxart-mmc.o
>  obj-$(CONFIG_MMC_SUNXI)		+= sunxi-mmc.o
> -obj-$(CONFIG_MMC_USDHI6ROL0)	+= usdhi6rol0.o
>  obj-$(CONFIG_MMC_TOSHIBA_PCI)	+= toshsd.o
>  obj-$(CONFIG_MMC_BCM2835)	+= bcm2835.o
>  obj-$(CONFIG_MMC_OWL)		+= owl-mmc.o
> diff --git a/drivers/mmc/host/usdhi6rol0.c b/drivers/mmc/host/usdhi6rol0.c
> deleted file mode 100644
> index 74888260e85c..000000000000
> --- a/drivers/mmc/host/usdhi6rol0.c
> +++ /dev/null
> @@ -1,1904 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Copyright (C) 2013-2014 Renesas Electronics Europe Ltd.
> - * Author: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
> - */
> -
> -#include <linux/clk.h>
> -#include <linux/delay.h>
> -#include <linux/device.h>
> -#include <linux/dma-mapping.h>
> -#include <linux/dmaengine.h>
> -#include <linux/highmem.h>
> -#include <linux/interrupt.h>
> -#include <linux/io.h>
> -#include <linux/log2.h>
> -#include <linux/mmc/host.h>
> -#include <linux/mmc/mmc.h>
> -#include <linux/mmc/sd.h>
> -#include <linux/mmc/sdio.h>
> -#include <linux/module.h>
> -#include <linux/pinctrl/consumer.h>
> -#include <linux/platform_device.h>
> -#include <linux/scatterlist.h>
> -#include <linux/string.h>
> -#include <linux/time.h>
> -#include <linux/virtio.h>
> -#include <linux/workqueue.h>
> -
> -#define USDHI6_SD_CMD		0x0000
> -#define USDHI6_SD_PORT_SEL	0x0004
> -#define USDHI6_SD_ARG		0x0008
> -#define USDHI6_SD_STOP		0x0010
> -#define USDHI6_SD_SECCNT	0x0014
> -#define USDHI6_SD_RSP10		0x0018
> -#define USDHI6_SD_RSP32		0x0020
> -#define USDHI6_SD_RSP54		0x0028
> -#define USDHI6_SD_RSP76		0x0030
> -#define USDHI6_SD_INFO1		0x0038
> -#define USDHI6_SD_INFO2		0x003c
> -#define USDHI6_SD_INFO1_MASK	0x0040
> -#define USDHI6_SD_INFO2_MASK	0x0044
> -#define USDHI6_SD_CLK_CTRL	0x0048
> -#define USDHI6_SD_SIZE		0x004c
> -#define USDHI6_SD_OPTION	0x0050
> -#define USDHI6_SD_ERR_STS1	0x0058
> -#define USDHI6_SD_ERR_STS2	0x005c
> -#define USDHI6_SD_BUF0		0x0060
> -#define USDHI6_SDIO_MODE	0x0068
> -#define USDHI6_SDIO_INFO1	0x006c
> -#define USDHI6_SDIO_INFO1_MASK	0x0070
> -#define USDHI6_CC_EXT_MODE	0x01b0
> -#define USDHI6_SOFT_RST		0x01c0
> -#define USDHI6_VERSION		0x01c4
> -#define USDHI6_HOST_MODE	0x01c8
> -#define USDHI6_SDIF_MODE	0x01cc
> -
> -#define USDHI6_SD_CMD_APP		0x0040
> -#define USDHI6_SD_CMD_MODE_RSP_AUTO	0x0000
> -#define USDHI6_SD_CMD_MODE_RSP_NONE	0x0300
> -#define USDHI6_SD_CMD_MODE_RSP_R1	0x0400	/* Also R5, R6, R7 */
> -#define USDHI6_SD_CMD_MODE_RSP_R1B	0x0500	/* R1b */
> -#define USDHI6_SD_CMD_MODE_RSP_R2	0x0600
> -#define USDHI6_SD_CMD_MODE_RSP_R3	0x0700	/* Also R4 */
> -#define USDHI6_SD_CMD_DATA		0x0800
> -#define USDHI6_SD_CMD_READ		0x1000
> -#define USDHI6_SD_CMD_MULTI		0x2000
> -#define USDHI6_SD_CMD_CMD12_AUTO_OFF	0x4000
> -
> -#define USDHI6_CC_EXT_MODE_SDRW		BIT(1)
> -
> -#define USDHI6_SD_INFO1_RSP_END		BIT(0)
> -#define USDHI6_SD_INFO1_ACCESS_END	BIT(2)
> -#define USDHI6_SD_INFO1_CARD_OUT	BIT(3)
> -#define USDHI6_SD_INFO1_CARD_IN		BIT(4)
> -#define USDHI6_SD_INFO1_CD		BIT(5)
> -#define USDHI6_SD_INFO1_WP		BIT(7)
> -#define USDHI6_SD_INFO1_D3_CARD_OUT	BIT(8)
> -#define USDHI6_SD_INFO1_D3_CARD_IN	BIT(9)
> -
> -#define USDHI6_SD_INFO2_CMD_ERR		BIT(0)
> -#define USDHI6_SD_INFO2_CRC_ERR		BIT(1)
> -#define USDHI6_SD_INFO2_END_ERR		BIT(2)
> -#define USDHI6_SD_INFO2_TOUT		BIT(3)
> -#define USDHI6_SD_INFO2_IWA_ERR		BIT(4)
> -#define USDHI6_SD_INFO2_IRA_ERR		BIT(5)
> -#define USDHI6_SD_INFO2_RSP_TOUT	BIT(6)
> -#define USDHI6_SD_INFO2_SDDAT0		BIT(7)
> -#define USDHI6_SD_INFO2_BRE		BIT(8)
> -#define USDHI6_SD_INFO2_BWE		BIT(9)
> -#define USDHI6_SD_INFO2_SCLKDIVEN	BIT(13)
> -#define USDHI6_SD_INFO2_CBSY		BIT(14)
> -#define USDHI6_SD_INFO2_ILA		BIT(15)
> -
> -#define USDHI6_SD_INFO1_CARD_INSERT (USDHI6_SD_INFO1_CARD_IN | USDHI6_SD_INFO1_D3_CARD_IN)
> -#define USDHI6_SD_INFO1_CARD_EJECT (USDHI6_SD_INFO1_CARD_OUT | USDHI6_SD_INFO1_D3_CARD_OUT)
> -#define USDHI6_SD_INFO1_CARD (USDHI6_SD_INFO1_CARD_INSERT | USDHI6_SD_INFO1_CARD_EJECT)
> -#define USDHI6_SD_INFO1_CARD_CD (USDHI6_SD_INFO1_CARD_IN | USDHI6_SD_INFO1_CARD_OUT)
> -
> -#define USDHI6_SD_INFO2_ERR	(USDHI6_SD_INFO2_CMD_ERR |	\
> -	USDHI6_SD_INFO2_CRC_ERR | USDHI6_SD_INFO2_END_ERR |	\
> -	USDHI6_SD_INFO2_TOUT | USDHI6_SD_INFO2_IWA_ERR |	\
> -	USDHI6_SD_INFO2_IRA_ERR | USDHI6_SD_INFO2_RSP_TOUT |	\
> -	USDHI6_SD_INFO2_ILA)
> -
> -#define USDHI6_SD_INFO1_IRQ	(USDHI6_SD_INFO1_RSP_END | USDHI6_SD_INFO1_ACCESS_END | \
> -				 USDHI6_SD_INFO1_CARD)
> -
> -#define USDHI6_SD_INFO2_IRQ	(USDHI6_SD_INFO2_ERR | USDHI6_SD_INFO2_BRE | \
> -				 USDHI6_SD_INFO2_BWE | 0x0800 | USDHI6_SD_INFO2_ILA)
> -
> -#define USDHI6_SD_CLK_CTRL_SCLKEN	BIT(8)
> -
> -#define USDHI6_SD_STOP_STP		BIT(0)
> -#define USDHI6_SD_STOP_SEC		BIT(8)
> -
> -#define USDHI6_SDIO_INFO1_IOIRQ		BIT(0)
> -#define USDHI6_SDIO_INFO1_EXPUB52	BIT(14)
> -#define USDHI6_SDIO_INFO1_EXWT		BIT(15)
> -
> -#define USDHI6_SD_ERR_STS1_CRC_NO_ERROR	BIT(13)
> -
> -#define USDHI6_SOFT_RST_RESERVED	(BIT(1) | BIT(2))
> -#define USDHI6_SOFT_RST_RESET		BIT(0)
> -
> -#define USDHI6_SD_OPTION_TIMEOUT_SHIFT	4
> -#define USDHI6_SD_OPTION_TIMEOUT_MASK	(0xf << USDHI6_SD_OPTION_TIMEOUT_SHIFT)
> -#define USDHI6_SD_OPTION_WIDTH_1	BIT(15)
> -
> -#define USDHI6_SD_PORT_SEL_PORTS_SHIFT	8
> -
> -#define USDHI6_SD_CLK_CTRL_DIV_MASK	0xff
> -
> -#define USDHI6_SDIO_INFO1_IRQ	(USDHI6_SDIO_INFO1_IOIRQ | 3 | \
> -				 USDHI6_SDIO_INFO1_EXPUB52 | USDHI6_SDIO_INFO1_EXWT)
> -
> -#define USDHI6_MIN_DMA 64
> -
> -#define USDHI6_REQ_TIMEOUT_MS 4000
> -
> -enum usdhi6_wait_for {
> -	USDHI6_WAIT_FOR_REQUEST,
> -	USDHI6_WAIT_FOR_CMD,
> -	USDHI6_WAIT_FOR_MREAD,
> -	USDHI6_WAIT_FOR_MWRITE,
> -	USDHI6_WAIT_FOR_READ,
> -	USDHI6_WAIT_FOR_WRITE,
> -	USDHI6_WAIT_FOR_DATA_END,
> -	USDHI6_WAIT_FOR_STOP,
> -	USDHI6_WAIT_FOR_DMA,
> -};
> -
> -struct usdhi6_page {
> -	struct page *page;
> -	void *mapped;		/* mapped page */
> -};
> -
> -struct usdhi6_host {
> -	struct mmc_host *mmc;
> -	struct mmc_request *mrq;
> -	void __iomem *base;
> -	struct clk *clk;
> -
> -	/* SG memory handling */
> -
> -	/* Common for multiple and single block requests */
> -	struct usdhi6_page pg;	/* current page from an SG */
> -	void *blk_page;		/* either a mapped page, or the bounce buffer */
> -	size_t offset;		/* offset within a page, including sg->offset */
> -
> -	/* Blocks, crossing a page boundary */
> -	size_t head_len;
> -	struct usdhi6_page head_pg;
> -
> -	/* A bounce buffer for unaligned blocks or blocks, crossing a page boundary */
> -	struct scatterlist bounce_sg;
> -	u8 bounce_buf[512];
> -
> -	/* Multiple block requests only */
> -	struct scatterlist *sg;	/* current SG segment */
> -	int page_idx;		/* page index within an SG segment */
> -
> -	enum usdhi6_wait_for wait;
> -	u32 status_mask;
> -	u32 status2_mask;
> -	u32 sdio_mask;
> -	u32 io_error;
> -	u32 irq_status;
> -	unsigned long imclk;
> -	unsigned long rate;
> -	bool app_cmd;
> -
> -	/* Timeout handling */
> -	struct delayed_work timeout_work;
> -	unsigned long timeout;
> -
> -	/* DMA support */
> -	struct dma_chan *chan_rx;
> -	struct dma_chan *chan_tx;
> -	bool dma_active;
> -
> -	/* Pin control */
> -	struct pinctrl *pinctrl;
> -	struct pinctrl_state *pins_uhs;
> -};
> -
> -/*			I/O primitives					*/
> -
> -static void usdhi6_write(struct usdhi6_host *host, u32 reg, u32 data)
> -{
> -	iowrite32(data, host->base + reg);
> -	dev_vdbg(mmc_dev(host->mmc), "%s(0x%p + 0x%x) = 0x%x\n", __func__,
> -		host->base, reg, data);
> -}
> -
> -static void usdhi6_write16(struct usdhi6_host *host, u32 reg, u16 data)
> -{
> -	iowrite16(data, host->base + reg);
> -	dev_vdbg(mmc_dev(host->mmc), "%s(0x%p + 0x%x) = 0x%x\n", __func__,
> -		host->base, reg, data);
> -}
> -
> -static u32 usdhi6_read(struct usdhi6_host *host, u32 reg)
> -{
> -	u32 data = ioread32(host->base + reg);
> -	dev_vdbg(mmc_dev(host->mmc), "%s(0x%p + 0x%x) = 0x%x\n", __func__,
> -		host->base, reg, data);
> -	return data;
> -}
> -
> -static u16 usdhi6_read16(struct usdhi6_host *host, u32 reg)
> -{
> -	u16 data = ioread16(host->base + reg);
> -	dev_vdbg(mmc_dev(host->mmc), "%s(0x%p + 0x%x) = 0x%x\n", __func__,
> -		host->base, reg, data);
> -	return data;
> -}
> -
> -static void usdhi6_irq_enable(struct usdhi6_host *host, u32 info1, u32 info2)
> -{
> -	host->status_mask = USDHI6_SD_INFO1_IRQ & ~info1;
> -	host->status2_mask = USDHI6_SD_INFO2_IRQ & ~info2;
> -	usdhi6_write(host, USDHI6_SD_INFO1_MASK, host->status_mask);
> -	usdhi6_write(host, USDHI6_SD_INFO2_MASK, host->status2_mask);
> -}
> -
> -static void usdhi6_wait_for_resp(struct usdhi6_host *host)
> -{
> -	usdhi6_irq_enable(host, USDHI6_SD_INFO1_RSP_END |
> -			  USDHI6_SD_INFO1_ACCESS_END | USDHI6_SD_INFO1_CARD_CD,
> -			  USDHI6_SD_INFO2_ERR);
> -}
> -
> -static void usdhi6_wait_for_brwe(struct usdhi6_host *host, bool read)
> -{
> -	usdhi6_irq_enable(host, USDHI6_SD_INFO1_ACCESS_END |
> -			  USDHI6_SD_INFO1_CARD_CD, USDHI6_SD_INFO2_ERR |
> -			  (read ? USDHI6_SD_INFO2_BRE : USDHI6_SD_INFO2_BWE));
> -}
> -
> -static void usdhi6_only_cd(struct usdhi6_host *host)
> -{
> -	/* Mask all except card hotplug */
> -	usdhi6_irq_enable(host, USDHI6_SD_INFO1_CARD_CD, 0);
> -}
> -
> -static void usdhi6_mask_all(struct usdhi6_host *host)
> -{
> -	usdhi6_irq_enable(host, 0, 0);
> -}
> -
> -static int usdhi6_error_code(struct usdhi6_host *host)
> -{
> -	u32 err;
> -
> -	usdhi6_write(host, USDHI6_SD_STOP, USDHI6_SD_STOP_STP);
> -
> -	if (host->io_error &
> -	    (USDHI6_SD_INFO2_RSP_TOUT | USDHI6_SD_INFO2_TOUT)) {
> -		u32 rsp54 = usdhi6_read(host, USDHI6_SD_RSP54);
> -		int opc = host->mrq ? host->mrq->cmd->opcode : -1;
> -
> -		err = usdhi6_read(host, USDHI6_SD_ERR_STS2);
> -		/* Response timeout is often normal, don't spam the log */
> -		if (host->wait == USDHI6_WAIT_FOR_CMD)
> -			dev_dbg(mmc_dev(host->mmc),
> -				"T-out sts 0x%x, resp 0x%x, state %u, CMD%d\n",
> -				err, rsp54, host->wait, opc);
> -		else
> -			dev_warn(mmc_dev(host->mmc),
> -				 "T-out sts 0x%x, resp 0x%x, state %u, CMD%d\n",
> -				 err, rsp54, host->wait, opc);
> -		return -ETIMEDOUT;
> -	}
> -
> -	err = usdhi6_read(host, USDHI6_SD_ERR_STS1);
> -	if (err != USDHI6_SD_ERR_STS1_CRC_NO_ERROR)
> -		dev_warn(mmc_dev(host->mmc), "Err sts 0x%x, state %u, CMD%d\n",
> -			 err, host->wait, host->mrq ? host->mrq->cmd->opcode : -1);
> -	if (host->io_error & USDHI6_SD_INFO2_ILA)
> -		return -EILSEQ;
> -
> -	return -EIO;
> -}
> -
> -/*			Scatter-Gather management			*/
> -
> -/*
> - * In PIO mode we have to map each page separately, using kmap(). That way
> - * adjacent pages are mapped to non-adjacent virtual addresses. That's why we
> - * have to use a bounce buffer for blocks, crossing page boundaries. Such blocks
> - * have been observed with an SDIO WiFi card (b43 driver).
> - */
> -static void usdhi6_blk_bounce(struct usdhi6_host *host,
> -			      struct scatterlist *sg)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	size_t blk_head = host->head_len;
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): CMD%u of %u SG: %ux%u @ 0x%x\n",
> -		__func__, host->mrq->cmd->opcode, data->sg_len,
> -		data->blksz, data->blocks, sg->offset);
> -
> -	host->head_pg.page	= host->pg.page;
> -	host->head_pg.mapped	= host->pg.mapped;
> -	host->pg.page		= host->pg.page + 1;
> -	host->pg.mapped		= kmap(host->pg.page);
> -
> -	host->blk_page = host->bounce_buf;
> -	host->offset = 0;
> -
> -	if (data->flags & MMC_DATA_READ)
> -		return;
> -
> -	memcpy(host->bounce_buf, host->head_pg.mapped + PAGE_SIZE - blk_head,
> -	       blk_head);
> -	memcpy(host->bounce_buf + blk_head, host->pg.mapped,
> -	       data->blksz - blk_head);
> -}
> -
> -/* Only called for multiple block IO */
> -static void usdhi6_sg_prep(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -	struct mmc_data *data = mrq->data;
> -
> -	usdhi6_write(host, USDHI6_SD_SECCNT, data->blocks);
> -
> -	host->sg = data->sg;
> -	/* TODO: if we always map, this is redundant */
> -	host->offset = host->sg->offset;
> -}
> -
> -/* Map the first page in an SG segment: common for multiple and single block IO */
> -static void *usdhi6_sg_map(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	struct scatterlist *sg = data->sg_len > 1 ? host->sg : data->sg;
> -	size_t head = PAGE_SIZE - sg->offset;
> -	size_t blk_head = head % data->blksz;
> -
> -	WARN(host->pg.page, "%p not properly unmapped!\n", host->pg.page);
> -	if (WARN(sg_dma_len(sg) % data->blksz,
> -		 "SG size %u isn't a multiple of block size %u\n",
> -		 sg_dma_len(sg), data->blksz))
> -		return NULL;
> -
> -	host->pg.page = sg_page(sg);
> -	host->pg.mapped = kmap(host->pg.page);
> -	host->offset = sg->offset;
> -
> -	/*
> -	 * Block size must be a power of 2 for multi-block transfers,
> -	 * therefore blk_head is equal for all pages in this SG
> -	 */
> -	host->head_len = blk_head;
> -
> -	if (head < data->blksz)
> -		/*
> -		 * The first block in the SG crosses a page boundary.
> -		 * Max blksz = 512, so blocks can only span 2 pages
> -		 */
> -		usdhi6_blk_bounce(host, sg);
> -	else
> -		host->blk_page = host->pg.mapped;
> -
> -	dev_dbg(mmc_dev(host->mmc), "Mapped %p (%lx) at %p + %u for CMD%u @ 0x%p\n",
> -		host->pg.page, page_to_pfn(host->pg.page), host->pg.mapped,
> -		sg->offset, host->mrq->cmd->opcode, host->mrq);
> -
> -	return host->blk_page + host->offset;
> -}
> -
> -/* Unmap the current page: common for multiple and single block IO */
> -static void usdhi6_sg_unmap(struct usdhi6_host *host, bool force)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	struct page *page = host->head_pg.page;
> -
> -	if (page) {
> -		/* Previous block was cross-page boundary */
> -		struct scatterlist *sg = data->sg_len > 1 ?
> -			host->sg : data->sg;
> -		size_t blk_head = host->head_len;
> -
> -		if (!data->error && data->flags & MMC_DATA_READ) {
> -			memcpy(host->head_pg.mapped + PAGE_SIZE - blk_head,
> -			       host->bounce_buf, blk_head);
> -			memcpy(host->pg.mapped, host->bounce_buf + blk_head,
> -			       data->blksz - blk_head);
> -		}
> -
> -		flush_dcache_page(page);
> -		kunmap(page);
> -
> -		host->head_pg.page = NULL;
> -
> -		if (!force && sg_dma_len(sg) + sg->offset >
> -		    (host->page_idx << PAGE_SHIFT) + data->blksz - blk_head)
> -			/* More blocks in this SG, don't unmap the next page */
> -			return;
> -	}
> -
> -	page = host->pg.page;
> -	if (!page)
> -		return;
> -
> -	flush_dcache_page(page);
> -	kunmap(page);
> -
> -	host->pg.page = NULL;
> -}
> -
> -/* Called from MMC_WRITE_MULTIPLE_BLOCK or MMC_READ_MULTIPLE_BLOCK */
> -static void usdhi6_sg_advance(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	size_t done, total;
> -
> -	/* New offset: set at the end of the previous block */
> -	if (host->head_pg.page) {
> -		/* Finished a cross-page block, jump to the new page */
> -		host->page_idx++;
> -		host->offset = data->blksz - host->head_len;
> -		host->blk_page = host->pg.mapped;
> -		usdhi6_sg_unmap(host, false);
> -	} else {
> -		host->offset += data->blksz;
> -		/* The completed block didn't cross a page boundary */
> -		if (host->offset == PAGE_SIZE) {
> -			/* If required, we'll map the page below */
> -			host->offset = 0;
> -			host->page_idx++;
> -		}
> -	}
> -
> -	/*
> -	 * Now host->blk_page + host->offset point at the end of our last block
> -	 * and host->page_idx is the index of the page, in which our new block
> -	 * is located, if any
> -	 */
> -
> -	done = (host->page_idx << PAGE_SHIFT) + host->offset;
> -	total = host->sg->offset + sg_dma_len(host->sg);
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): %zu of %zu @ %zu\n", __func__,
> -		done, total, host->offset);
> -
> -	if (done < total && host->offset) {
> -		/* More blocks in this page */
> -		if (host->offset + data->blksz > PAGE_SIZE)
> -			/* We approached at a block, that spans 2 pages */
> -			usdhi6_blk_bounce(host, host->sg);
> -
> -		return;
> -	}
> -
> -	/* Finished current page or an SG segment */
> -	usdhi6_sg_unmap(host, false);
> -
> -	if (done == total) {
> -		/*
> -		 * End of an SG segment or the complete SG: jump to the next
> -		 * segment, we'll map it later in usdhi6_blk_read() or
> -		 * usdhi6_blk_write()
> -		 */
> -		struct scatterlist *next = sg_next(host->sg);
> -
> -		host->page_idx = 0;
> -
> -		if (!next)
> -			host->wait = USDHI6_WAIT_FOR_DATA_END;
> -		host->sg = next;
> -
> -		if (WARN(next && sg_dma_len(next) % data->blksz,
> -			 "SG size %u isn't a multiple of block size %u\n",
> -			 sg_dma_len(next), data->blksz))
> -			data->error = -EINVAL;
> -
> -		return;
> -	}
> -
> -	/* We cannot get here after crossing a page border */
> -
> -	/* Next page in the same SG */
> -	host->pg.page = sg_page(host->sg) + host->page_idx;
> -	host->pg.mapped = kmap(host->pg.page);
> -	host->blk_page = host->pg.mapped;
> -
> -	dev_dbg(mmc_dev(host->mmc), "Mapped %p (%lx) at %p for CMD%u @ 0x%p\n",
> -		host->pg.page, page_to_pfn(host->pg.page), host->pg.mapped,
> -		host->mrq->cmd->opcode, host->mrq);
> -}
> -
> -/*			DMA handling					*/
> -
> -static void usdhi6_dma_release(struct usdhi6_host *host)
> -{
> -	host->dma_active = false;
> -	if (host->chan_tx) {
> -		struct dma_chan *chan = host->chan_tx;
> -		host->chan_tx = NULL;
> -		dma_release_channel(chan);
> -	}
> -	if (host->chan_rx) {
> -		struct dma_chan *chan = host->chan_rx;
> -		host->chan_rx = NULL;
> -		dma_release_channel(chan);
> -	}
> -}
> -
> -static void usdhi6_dma_stop_unmap(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -
> -	if (!host->dma_active)
> -		return;
> -
> -	usdhi6_write(host, USDHI6_CC_EXT_MODE, 0);
> -	host->dma_active = false;
> -
> -	if (data->flags & MMC_DATA_READ)
> -		dma_unmap_sg(dmaengine_get_dma_device(host->chan_rx), data->sg,
> -			     data->sg_len, DMA_FROM_DEVICE);
> -	else
> -		dma_unmap_sg(dmaengine_get_dma_device(host->chan_tx), data->sg,
> -			     data->sg_len, DMA_TO_DEVICE);
> -}
> -
> -static void usdhi6_dma_complete(void *arg)
> -{
> -	struct usdhi6_host *host = arg;
> -	struct mmc_request *mrq = host->mrq;
> -
> -	if (WARN(!mrq || !mrq->data, "%s: NULL data in DMA completion for %p!\n",
> -		 dev_name(mmc_dev(host->mmc)), mrq))
> -		return;
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): CMD%u DMA completed\n", __func__,
> -		mrq->cmd->opcode);
> -
> -	usdhi6_dma_stop_unmap(host);
> -	usdhi6_wait_for_brwe(host, mrq->data->flags & MMC_DATA_READ);
> -}
> -
> -static int usdhi6_dma_setup(struct usdhi6_host *host, struct dma_chan *chan,
> -			    enum dma_transfer_direction dir)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	struct scatterlist *sg = data->sg;
> -	struct dma_async_tx_descriptor *desc = NULL;
> -	dma_cookie_t cookie = -EINVAL;
> -	enum dma_data_direction data_dir;
> -	int ret;
> -
> -	switch (dir) {
> -	case DMA_MEM_TO_DEV:
> -		data_dir = DMA_TO_DEVICE;
> -		break;
> -	case DMA_DEV_TO_MEM:
> -		data_dir = DMA_FROM_DEVICE;
> -		break;
> -	default:
> -		return -EINVAL;
> -	}
> -
> -	ret = dma_map_sg(dmaengine_get_dma_device(chan), sg, data->sg_len, data_dir);
> -	if (ret > 0) {
> -		host->dma_active = true;
> -		desc = dmaengine_prep_slave_sg(chan, sg, ret, dir,
> -					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
> -	}
> -
> -	if (desc) {
> -		desc->callback = usdhi6_dma_complete;
> -		desc->callback_param = host;
> -		cookie = dmaengine_submit(desc);
> -	}
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): mapped %d -> %d, cookie %d @ %p\n",
> -		__func__, data->sg_len, ret, cookie, desc);
> -
> -	if (cookie < 0) {
> -		/* DMA failed, fall back to PIO */
> -		if (ret >= 0)
> -			ret = cookie;
> -		usdhi6_dma_release(host);
> -		dev_warn(mmc_dev(host->mmc),
> -			 "DMA failed: %d, falling back to PIO\n", ret);
> -	}
> -
> -	return cookie;
> -}
> -
> -static int usdhi6_dma_start(struct usdhi6_host *host)
> -{
> -	if (!host->chan_rx || !host->chan_tx)
> -		return -ENODEV;
> -
> -	if (host->mrq->data->flags & MMC_DATA_READ)
> -		return usdhi6_dma_setup(host, host->chan_rx, DMA_DEV_TO_MEM);
> -
> -	return usdhi6_dma_setup(host, host->chan_tx, DMA_MEM_TO_DEV);
> -}
> -
> -static void usdhi6_dma_kill(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): SG of %u: %ux%u\n",
> -		__func__, data->sg_len, data->blocks, data->blksz);
> -	/* Abort DMA */
> -	if (data->flags & MMC_DATA_READ)
> -		dmaengine_terminate_sync(host->chan_rx);
> -	else
> -		dmaengine_terminate_sync(host->chan_tx);
> -}
> -
> -static void usdhi6_dma_check_error(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): IO error %d, status 0x%x\n",
> -		__func__, host->io_error, usdhi6_read(host, USDHI6_SD_INFO1));
> -
> -	if (host->io_error) {
> -		data->error = usdhi6_error_code(host);
> -		data->bytes_xfered = 0;
> -		usdhi6_dma_kill(host);
> -		usdhi6_dma_release(host);
> -		dev_warn(mmc_dev(host->mmc),
> -			 "DMA failed: %d, falling back to PIO\n", data->error);
> -		return;
> -	}
> -
> -	/*
> -	 * The datasheet tells us to check a response from the card, whereas
> -	 * responses only come after the command phase, not after the data
> -	 * phase. Let's check anyway.
> -	 */
> -	if (host->irq_status & USDHI6_SD_INFO1_RSP_END)
> -		dev_warn(mmc_dev(host->mmc), "Unexpected response received!\n");
> -}
> -
> -static void usdhi6_dma_kick(struct usdhi6_host *host)
> -{
> -	if (host->mrq->data->flags & MMC_DATA_READ)
> -		dma_async_issue_pending(host->chan_rx);
> -	else
> -		dma_async_issue_pending(host->chan_tx);
> -}
> -
> -static void usdhi6_dma_request(struct usdhi6_host *host, phys_addr_t start)
> -{
> -	struct dma_slave_config cfg = {
> -		.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
> -		.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
> -	};
> -	int ret;
> -
> -	host->chan_tx = dma_request_chan(mmc_dev(host->mmc), "tx");
> -	dev_dbg(mmc_dev(host->mmc), "%s: TX: got channel %p\n", __func__,
> -		host->chan_tx);
> -
> -	if (IS_ERR(host->chan_tx)) {
> -		host->chan_tx = NULL;
> -		return;
> -	}
> -
> -	cfg.direction = DMA_MEM_TO_DEV;
> -	cfg.dst_addr = start + USDHI6_SD_BUF0;
> -	cfg.dst_maxburst = 128;	/* 128 words * 4 bytes = 512 bytes */
> -	cfg.src_addr = 0;
> -	ret = dmaengine_slave_config(host->chan_tx, &cfg);
> -	if (ret < 0)
> -		goto e_release_tx;
> -
> -	host->chan_rx = dma_request_chan(mmc_dev(host->mmc), "rx");
> -	dev_dbg(mmc_dev(host->mmc), "%s: RX: got channel %p\n", __func__,
> -		host->chan_rx);
> -
> -	if (IS_ERR(host->chan_rx)) {
> -		host->chan_rx = NULL;
> -		goto e_release_tx;
> -	}
> -
> -	cfg.direction = DMA_DEV_TO_MEM;
> -	cfg.src_addr = cfg.dst_addr;
> -	cfg.src_maxburst = 128;	/* 128 words * 4 bytes = 512 bytes */
> -	cfg.dst_addr = 0;
> -	ret = dmaengine_slave_config(host->chan_rx, &cfg);
> -	if (ret < 0)
> -		goto e_release_rx;
> -
> -	return;
> -
> -e_release_rx:
> -	dma_release_channel(host->chan_rx);
> -	host->chan_rx = NULL;
> -e_release_tx:
> -	dma_release_channel(host->chan_tx);
> -	host->chan_tx = NULL;
> -}
> -
> -/*			API helpers					*/
> -
> -static void usdhi6_clk_set(struct usdhi6_host *host, struct mmc_ios *ios)
> -{
> -	unsigned long rate = ios->clock;
> -	u32 val;
> -	unsigned int i;
> -
> -	for (i = 1000; i; i--) {
> -		if (usdhi6_read(host, USDHI6_SD_INFO2) & USDHI6_SD_INFO2_SCLKDIVEN)
> -			break;
> -		usleep_range(10, 100);
> -	}
> -
> -	if (!i) {
> -		dev_err(mmc_dev(host->mmc), "SD bus busy, clock set aborted\n");
> -		return;
> -	}
> -
> -	val = usdhi6_read(host, USDHI6_SD_CLK_CTRL) & ~USDHI6_SD_CLK_CTRL_DIV_MASK;
> -
> -	if (rate) {
> -		unsigned long new_rate;
> -
> -		if (host->imclk <= rate) {
> -			if (ios->timing != MMC_TIMING_UHS_DDR50) {
> -				/* Cannot have 1-to-1 clock in DDR mode */
> -				new_rate = host->imclk;
> -				val |= 0xff;
> -			} else {
> -				new_rate = host->imclk / 2;
> -			}
> -		} else {
> -			unsigned long div =
> -				roundup_pow_of_two(DIV_ROUND_UP(host->imclk, rate));
> -			val |= div >> 2;
> -			new_rate = host->imclk / div;
> -		}
> -
> -		if (host->rate == new_rate)
> -			return;
> -
> -		host->rate = new_rate;
> -
> -		dev_dbg(mmc_dev(host->mmc), "target %lu, div %u, set %lu\n",
> -			rate, (val & 0xff) << 2, new_rate);
> -	}
> -
> -	/*
> -	 * if old or new rate is equal to input rate, have to switch the clock
> -	 * off before changing and on after
> -	 */
> -	if (host->imclk == rate || host->imclk == host->rate || !rate)
> -		usdhi6_write(host, USDHI6_SD_CLK_CTRL,
> -			     val & ~USDHI6_SD_CLK_CTRL_SCLKEN);
> -
> -	if (!rate) {
> -		host->rate = 0;
> -		return;
> -	}
> -
> -	usdhi6_write(host, USDHI6_SD_CLK_CTRL, val);
> -
> -	if (host->imclk == rate || host->imclk == host->rate ||
> -	    !(val & USDHI6_SD_CLK_CTRL_SCLKEN))
> -		usdhi6_write(host, USDHI6_SD_CLK_CTRL,
> -			     val | USDHI6_SD_CLK_CTRL_SCLKEN);
> -}
> -
> -static void usdhi6_set_power(struct usdhi6_host *host, struct mmc_ios *ios)
> -{
> -	struct mmc_host *mmc = host->mmc;
> -
> -	if (!IS_ERR(mmc->supply.vmmc))
> -		/* Errors ignored... */
> -		mmc_regulator_set_ocr(mmc, mmc->supply.vmmc,
> -				      ios->power_mode ? ios->vdd : 0);
> -}
> -
> -static int usdhi6_reset(struct usdhi6_host *host)
> -{
> -	int i;
> -
> -	usdhi6_write(host, USDHI6_SOFT_RST, USDHI6_SOFT_RST_RESERVED);
> -	cpu_relax();
> -	usdhi6_write(host, USDHI6_SOFT_RST, USDHI6_SOFT_RST_RESERVED | USDHI6_SOFT_RST_RESET);
> -	for (i = 1000; i; i--)
> -		if (usdhi6_read(host, USDHI6_SOFT_RST) & USDHI6_SOFT_RST_RESET)
> -			break;
> -
> -	return i ? 0 : -ETIMEDOUT;
> -}
> -
> -static void usdhi6_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> -{
> -	struct usdhi6_host *host = mmc_priv(mmc);
> -	u32 option, mode;
> -	int ret;
> -
> -	dev_dbg(mmc_dev(mmc), "%uHz, OCR: %u, power %u, bus-width %u, timing %u\n",
> -		ios->clock, ios->vdd, ios->power_mode, ios->bus_width, ios->timing);
> -
> -	switch (ios->power_mode) {
> -	case MMC_POWER_OFF:
> -		usdhi6_set_power(host, ios);
> -		usdhi6_only_cd(host);
> -		break;
> -	case MMC_POWER_UP:
> -		/*
> -		 * We only also touch USDHI6_SD_OPTION from .request(), which
> -		 * cannot race with MMC_POWER_UP
> -		 */
> -		ret = usdhi6_reset(host);
> -		if (ret < 0) {
> -			dev_err(mmc_dev(mmc), "Cannot reset the interface!\n");
> -		} else {
> -			usdhi6_set_power(host, ios);
> -			usdhi6_only_cd(host);
> -		}
> -		break;
> -	case MMC_POWER_ON:
> -		option = usdhi6_read(host, USDHI6_SD_OPTION);
> -		/*
> -		 * The eMMC standard only allows 4 or 8 bits in the DDR mode,
> -		 * the same probably holds for SD cards. We check here anyway,
> -		 * since the datasheet explicitly requires 4 bits for DDR.
> -		 */
> -		if (ios->bus_width == MMC_BUS_WIDTH_1) {
> -			if (ios->timing == MMC_TIMING_UHS_DDR50)
> -				dev_err(mmc_dev(mmc),
> -					"4 bits are required for DDR\n");
> -			option |= USDHI6_SD_OPTION_WIDTH_1;
> -			mode = 0;
> -		} else {
> -			option &= ~USDHI6_SD_OPTION_WIDTH_1;
> -			mode = ios->timing == MMC_TIMING_UHS_DDR50;
> -		}
> -		usdhi6_write(host, USDHI6_SD_OPTION, option);
> -		usdhi6_write(host, USDHI6_SDIF_MODE, mode);
> -		break;
> -	}
> -
> -	if (host->rate != ios->clock)
> -		usdhi6_clk_set(host, ios);
> -}
> -
> -/* This is data timeout. Response timeout is fixed to 640 clock cycles */
> -static void usdhi6_timeout_set(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -	u32 val;
> -	unsigned long ticks;
> -
> -	if (!mrq->data)
> -		ticks = host->rate / 1000 * mrq->cmd->busy_timeout;
> -	else
> -		ticks = host->rate / 1000000 * (mrq->data->timeout_ns / 1000) +
> -			mrq->data->timeout_clks;
> -
> -	if (!ticks || ticks > 1 << 27)
> -		/* Max timeout */
> -		val = 14;
> -	else if (ticks < 1 << 13)
> -		/* Min timeout */
> -		val = 0;
> -	else
> -		val = order_base_2(ticks) - 13;
> -
> -	dev_dbg(mmc_dev(host->mmc), "Set %s timeout %lu ticks @ %lu Hz\n",
> -		mrq->data ? "data" : "cmd", ticks, host->rate);
> -
> -	/* Timeout Counter mask: 0xf0 */
> -	usdhi6_write(host, USDHI6_SD_OPTION, (val << USDHI6_SD_OPTION_TIMEOUT_SHIFT) |
> -		     (usdhi6_read(host, USDHI6_SD_OPTION) & ~USDHI6_SD_OPTION_TIMEOUT_MASK));
> -}
> -
> -static void usdhi6_request_done(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -	struct mmc_data *data = mrq->data;
> -
> -	if (WARN(host->pg.page || host->head_pg.page,
> -		 "Page %p or %p not unmapped: wait %u, CMD%d(%c) @ +0x%zx %ux%u in SG%u!\n",
> -		 host->pg.page, host->head_pg.page, host->wait, mrq->cmd->opcode,
> -		 data ? (data->flags & MMC_DATA_READ ? 'R' : 'W') : '-',
> -		 data ? host->offset : 0, data ? data->blocks : 0,
> -		 data ? data->blksz : 0, data ? data->sg_len : 0))
> -		usdhi6_sg_unmap(host, true);
> -
> -	if (mrq->cmd->error ||
> -	    (data && data->error) ||
> -	    (mrq->stop && mrq->stop->error))
> -		dev_dbg(mmc_dev(host->mmc), "%s(CMD%d: %ux%u): err %d %d %d\n",
> -			__func__, mrq->cmd->opcode, data ? data->blocks : 0,
> -			data ? data->blksz : 0,
> -			mrq->cmd->error,
> -			data ? data->error : 1,
> -			mrq->stop ? mrq->stop->error : 1);
> -
> -	/* Disable DMA */
> -	usdhi6_write(host, USDHI6_CC_EXT_MODE, 0);
> -	host->wait = USDHI6_WAIT_FOR_REQUEST;
> -	host->mrq = NULL;
> -
> -	mmc_request_done(host->mmc, mrq);
> -}
> -
> -static int usdhi6_cmd_flags(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -	struct mmc_command *cmd = mrq->cmd;
> -	u16 opc = cmd->opcode;
> -
> -	if (host->app_cmd) {
> -		host->app_cmd = false;
> -		opc |= USDHI6_SD_CMD_APP;
> -	}
> -
> -	if (mrq->data) {
> -		opc |= USDHI6_SD_CMD_DATA;
> -
> -		if (mrq->data->flags & MMC_DATA_READ)
> -			opc |= USDHI6_SD_CMD_READ;
> -
> -		if (cmd->opcode == MMC_READ_MULTIPLE_BLOCK ||
> -		    cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
> -		    (cmd->opcode == SD_IO_RW_EXTENDED &&
> -		     mrq->data->blocks > 1)) {
> -			opc |= USDHI6_SD_CMD_MULTI;
> -			if (!mrq->stop)
> -				opc |= USDHI6_SD_CMD_CMD12_AUTO_OFF;
> -		}
> -
> -		switch (mmc_resp_type(cmd)) {
> -		case MMC_RSP_NONE:
> -			opc |= USDHI6_SD_CMD_MODE_RSP_NONE;
> -			break;
> -		case MMC_RSP_R1:
> -			opc |= USDHI6_SD_CMD_MODE_RSP_R1;
> -			break;
> -		case MMC_RSP_R1B:
> -			opc |= USDHI6_SD_CMD_MODE_RSP_R1B;
> -			break;
> -		case MMC_RSP_R2:
> -			opc |= USDHI6_SD_CMD_MODE_RSP_R2;
> -			break;
> -		case MMC_RSP_R3:
> -			opc |= USDHI6_SD_CMD_MODE_RSP_R3;
> -			break;
> -		default:
> -			dev_warn(mmc_dev(host->mmc),
> -				 "Unknown response type %d\n",
> -				 mmc_resp_type(cmd));
> -			return -EINVAL;
> -		}
> -	}
> -
> -	return opc;
> -}
> -
> -static int usdhi6_rq_start(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -	struct mmc_command *cmd = mrq->cmd;
> -	struct mmc_data *data = mrq->data;
> -	int opc = usdhi6_cmd_flags(host);
> -	int i;
> -
> -	if (opc < 0)
> -		return opc;
> -
> -	for (i = 1000; i; i--) {
> -		if (!(usdhi6_read(host, USDHI6_SD_INFO2) & USDHI6_SD_INFO2_CBSY))
> -			break;
> -		usleep_range(10, 100);
> -	}
> -
> -	if (!i) {
> -		dev_dbg(mmc_dev(host->mmc), "Command active, request aborted\n");
> -		return -EAGAIN;
> -	}
> -
> -	if (data) {
> -		bool use_dma;
> -		int ret = 0;
> -
> -		host->page_idx = 0;
> -
> -		if (cmd->opcode == SD_IO_RW_EXTENDED && data->blocks > 1) {
> -			switch (data->blksz) {
> -			case 512:
> -				break;
> -			case 32:
> -			case 64:
> -			case 128:
> -			case 256:
> -				if (mrq->stop)
> -					ret = -EINVAL;
> -				break;
> -			default:
> -				ret = -EINVAL;
> -			}
> -		} else if ((cmd->opcode == MMC_READ_MULTIPLE_BLOCK ||
> -			    cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK) &&
> -			   data->blksz != 512) {
> -			ret = -EINVAL;
> -		}
> -
> -		if (ret < 0) {
> -			dev_warn(mmc_dev(host->mmc), "%s(): %u blocks of %u bytes\n",
> -				 __func__, data->blocks, data->blksz);
> -			return -EINVAL;
> -		}
> -
> -		if (cmd->opcode == MMC_READ_MULTIPLE_BLOCK ||
> -		    cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
> -		    (cmd->opcode == SD_IO_RW_EXTENDED &&
> -		     data->blocks > 1))
> -			usdhi6_sg_prep(host);
> -
> -		usdhi6_write(host, USDHI6_SD_SIZE, data->blksz);
> -
> -		if ((data->blksz >= USDHI6_MIN_DMA ||
> -		     data->blocks > 1) &&
> -		    (data->blksz % 4 ||
> -		     data->sg->offset % 4))
> -			dev_dbg(mmc_dev(host->mmc),
> -				"Bad SG of %u: %ux%u @ %u\n", data->sg_len,
> -				data->blksz, data->blocks, data->sg->offset);
> -
> -		/* Enable DMA for USDHI6_MIN_DMA bytes or more */
> -		use_dma = data->blksz >= USDHI6_MIN_DMA &&
> -			!(data->blksz % 4) &&
> -			usdhi6_dma_start(host) >= DMA_MIN_COOKIE;
> -
> -		if (use_dma)
> -			usdhi6_write(host, USDHI6_CC_EXT_MODE, USDHI6_CC_EXT_MODE_SDRW);
> -
> -		dev_dbg(mmc_dev(host->mmc),
> -			"%s(): request opcode %u, %u blocks of %u bytes in %u segments, %s %s @+0x%x%s\n",
> -			__func__, cmd->opcode, data->blocks, data->blksz,
> -			data->sg_len, use_dma ? "DMA" : "PIO",
> -			data->flags & MMC_DATA_READ ? "read" : "write",
> -			data->sg->offset, mrq->stop ? " + stop" : "");
> -	} else {
> -		dev_dbg(mmc_dev(host->mmc), "%s(): request opcode %u\n",
> -			__func__, cmd->opcode);
> -	}
> -
> -	/* We have to get a command completion interrupt with DMA too */
> -	usdhi6_wait_for_resp(host);
> -
> -	host->wait = USDHI6_WAIT_FOR_CMD;
> -	schedule_delayed_work(&host->timeout_work, host->timeout);
> -
> -	/* SEC bit is required to enable block counting by the core */
> -	usdhi6_write(host, USDHI6_SD_STOP,
> -		     data && data->blocks > 1 ? USDHI6_SD_STOP_SEC : 0);
> -	usdhi6_write(host, USDHI6_SD_ARG, cmd->arg);
> -
> -	/* Kick command execution */
> -	usdhi6_write(host, USDHI6_SD_CMD, opc);
> -
> -	return 0;
> -}
> -
> -static void usdhi6_request(struct mmc_host *mmc, struct mmc_request *mrq)
> -{
> -	struct usdhi6_host *host = mmc_priv(mmc);
> -	int ret;
> -
> -	cancel_delayed_work_sync(&host->timeout_work);
> -
> -	host->mrq = mrq;
> -	host->sg = NULL;
> -
> -	usdhi6_timeout_set(host);
> -	ret = usdhi6_rq_start(host);
> -	if (ret < 0) {
> -		mrq->cmd->error = ret;
> -		usdhi6_request_done(host);
> -	}
> -}
> -
> -static int usdhi6_get_cd(struct mmc_host *mmc)
> -{
> -	struct usdhi6_host *host = mmc_priv(mmc);
> -	/* Read is atomic, no need to lock */
> -	u32 status = usdhi6_read(host, USDHI6_SD_INFO1) & USDHI6_SD_INFO1_CD;
> -
> -/*
> - *	level	status.CD	CD_ACTIVE_HIGH	card present
> - *	1	0		0		0
> - *	1	0		1		1
> - *	0	1		0		1
> - *	0	1		1		0
> - */
> -	return !status ^ !(mmc->caps2 & MMC_CAP2_CD_ACTIVE_HIGH);
> -}
> -
> -static int usdhi6_get_ro(struct mmc_host *mmc)
> -{
> -	struct usdhi6_host *host = mmc_priv(mmc);
> -	/* No locking as above */
> -	u32 status = usdhi6_read(host, USDHI6_SD_INFO1) & USDHI6_SD_INFO1_WP;
> -
> -/*
> - *	level	status.WP	RO_ACTIVE_HIGH	card read-only
> - *	1	0		0		0
> - *	1	0		1		1
> - *	0	1		0		1
> - *	0	1		1		0
> - */
> -	return !status ^ !(mmc->caps2 & MMC_CAP2_RO_ACTIVE_HIGH);
> -}
> -
> -static void usdhi6_enable_sdio_irq(struct mmc_host *mmc, int enable)
> -{
> -	struct usdhi6_host *host = mmc_priv(mmc);
> -
> -	dev_dbg(mmc_dev(mmc), "%s(): %sable\n", __func__, enable ? "en" : "dis");
> -
> -	if (enable) {
> -		host->sdio_mask = USDHI6_SDIO_INFO1_IRQ & ~USDHI6_SDIO_INFO1_IOIRQ;
> -		usdhi6_write(host, USDHI6_SDIO_INFO1_MASK, host->sdio_mask);
> -		usdhi6_write(host, USDHI6_SDIO_MODE, 1);
> -	} else {
> -		usdhi6_write(host, USDHI6_SDIO_MODE, 0);
> -		usdhi6_write(host, USDHI6_SDIO_INFO1_MASK, USDHI6_SDIO_INFO1_IRQ);
> -		host->sdio_mask = USDHI6_SDIO_INFO1_IRQ;
> -	}
> -}
> -
> -static int usdhi6_set_pinstates(struct usdhi6_host *host, int voltage)
> -{
> -	if (IS_ERR(host->pins_uhs))
> -		return 0;
> -
> -	switch (voltage) {
> -	case MMC_SIGNAL_VOLTAGE_180:
> -	case MMC_SIGNAL_VOLTAGE_120:
> -		return pinctrl_select_state(host->pinctrl,
> -					    host->pins_uhs);
> -
> -	default:
> -		return pinctrl_select_default_state(mmc_dev(host->mmc));
> -	}
> -}
> -
> -static int usdhi6_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
> -{
> -	int ret;
> -
> -	ret = mmc_regulator_set_vqmmc(mmc, ios);
> -	if (ret < 0)
> -		return ret;
> -
> -	ret = usdhi6_set_pinstates(mmc_priv(mmc), ios->signal_voltage);
> -	if (ret)
> -		dev_warn_once(mmc_dev(mmc),
> -			      "Failed to set pinstate err=%d\n", ret);
> -	return ret;
> -}
> -
> -static int usdhi6_card_busy(struct mmc_host *mmc)
> -{
> -	struct usdhi6_host *host = mmc_priv(mmc);
> -	u32 tmp = usdhi6_read(host, USDHI6_SD_INFO2);
> -
> -	/* Card is busy if it is pulling dat[0] low */
> -	return !(tmp & USDHI6_SD_INFO2_SDDAT0);
> -}
> -
> -static const struct mmc_host_ops usdhi6_ops = {
> -	.request	= usdhi6_request,
> -	.set_ios	= usdhi6_set_ios,
> -	.get_cd		= usdhi6_get_cd,
> -	.get_ro		= usdhi6_get_ro,
> -	.enable_sdio_irq = usdhi6_enable_sdio_irq,
> -	.start_signal_voltage_switch = usdhi6_sig_volt_switch,
> -	.card_busy = usdhi6_card_busy,
> -};
> -
> -/*			State machine handlers				*/
> -
> -static void usdhi6_resp_cmd12(struct usdhi6_host *host)
> -{
> -	struct mmc_command *cmd = host->mrq->stop;
> -	cmd->resp[0] = usdhi6_read(host, USDHI6_SD_RSP10);
> -}
> -
> -static void usdhi6_resp_read(struct usdhi6_host *host)
> -{
> -	struct mmc_command *cmd = host->mrq->cmd;
> -	u32 *rsp = cmd->resp, tmp = 0;
> -	int i;
> -
> -/*
> - * RSP10	39-8
> - * RSP32	71-40
> - * RSP54	103-72
> - * RSP76	127-104
> - * R2-type response:
> - * resp[0]	= r[127..96]
> - * resp[1]	= r[95..64]
> - * resp[2]	= r[63..32]
> - * resp[3]	= r[31..0]
> - * Other responses:
> - * resp[0]	= r[39..8]
> - */
> -
> -	if (mmc_resp_type(cmd) == MMC_RSP_NONE)
> -		return;
> -
> -	if (!(host->irq_status & USDHI6_SD_INFO1_RSP_END)) {
> -		dev_err(mmc_dev(host->mmc),
> -			"CMD%d: response expected but is missing!\n", cmd->opcode);
> -		return;
> -	}
> -
> -	if (mmc_resp_type(cmd) & MMC_RSP_136)
> -		for (i = 0; i < 4; i++) {
> -			if (i)
> -				rsp[3 - i] = tmp >> 24;
> -			tmp = usdhi6_read(host, USDHI6_SD_RSP10 + i * 8);
> -			rsp[3 - i] |= tmp << 8;
> -		}
> -	else if (cmd->opcode == MMC_READ_MULTIPLE_BLOCK ||
> -		 cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK)
> -		/* Read RSP54 to avoid conflict with auto CMD12 */
> -		rsp[0] = usdhi6_read(host, USDHI6_SD_RSP54);
> -	else
> -		rsp[0] = usdhi6_read(host, USDHI6_SD_RSP10);
> -
> -	dev_dbg(mmc_dev(host->mmc), "Response 0x%x\n", rsp[0]);
> -}
> -
> -static int usdhi6_blk_read(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	u32 *p;
> -	int i, rest;
> -
> -	if (host->io_error) {
> -		data->error = usdhi6_error_code(host);
> -		goto error;
> -	}
> -
> -	if (host->pg.page) {
> -		p = host->blk_page + host->offset;
> -	} else {
> -		p = usdhi6_sg_map(host);
> -		if (!p) {
> -			data->error = -ENOMEM;
> -			goto error;
> -		}
> -	}
> -
> -	for (i = 0; i < data->blksz / 4; i++, p++)
> -		*p = usdhi6_read(host, USDHI6_SD_BUF0);
> -
> -	rest = data->blksz % 4;
> -	for (i = 0; i < (rest + 1) / 2; i++) {
> -		u16 d = usdhi6_read16(host, USDHI6_SD_BUF0);
> -		((u8 *)p)[2 * i] = ((u8 *)&d)[0];
> -		if (rest > 1 && !i)
> -			((u8 *)p)[2 * i + 1] = ((u8 *)&d)[1];
> -	}
> -
> -	return 0;
> -
> -error:
> -	dev_dbg(mmc_dev(host->mmc), "%s(): %d\n", __func__, data->error);
> -	host->wait = USDHI6_WAIT_FOR_REQUEST;
> -	return data->error;
> -}
> -
> -static int usdhi6_blk_write(struct usdhi6_host *host)
> -{
> -	struct mmc_data *data = host->mrq->data;
> -	u32 *p;
> -	int i, rest;
> -
> -	if (host->io_error) {
> -		data->error = usdhi6_error_code(host);
> -		goto error;
> -	}
> -
> -	if (host->pg.page) {
> -		p = host->blk_page + host->offset;
> -	} else {
> -		p = usdhi6_sg_map(host);
> -		if (!p) {
> -			data->error = -ENOMEM;
> -			goto error;
> -		}
> -	}
> -
> -	for (i = 0; i < data->blksz / 4; i++, p++)
> -		usdhi6_write(host, USDHI6_SD_BUF0, *p);
> -
> -	rest = data->blksz % 4;
> -	for (i = 0; i < (rest + 1) / 2; i++) {
> -		u16 d;
> -		((u8 *)&d)[0] = ((u8 *)p)[2 * i];
> -		if (rest > 1 && !i)
> -			((u8 *)&d)[1] = ((u8 *)p)[2 * i + 1];
> -		else
> -			((u8 *)&d)[1] = 0;
> -		usdhi6_write16(host, USDHI6_SD_BUF0, d);
> -	}
> -
> -	return 0;
> -
> -error:
> -	dev_dbg(mmc_dev(host->mmc), "%s(): %d\n", __func__, data->error);
> -	host->wait = USDHI6_WAIT_FOR_REQUEST;
> -	return data->error;
> -}
> -
> -static int usdhi6_stop_cmd(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -
> -	switch (mrq->cmd->opcode) {
> -	case MMC_READ_MULTIPLE_BLOCK:
> -	case MMC_WRITE_MULTIPLE_BLOCK:
> -		if (mrq->stop->opcode == MMC_STOP_TRANSMISSION) {
> -			host->wait = USDHI6_WAIT_FOR_STOP;
> -			return 0;
> -		}
> -		fallthrough;	/* Unsupported STOP command */
> -	default:
> -		dev_err(mmc_dev(host->mmc),
> -			"unsupported stop CMD%d for CMD%d\n",
> -			mrq->stop->opcode, mrq->cmd->opcode);
> -		mrq->stop->error = -EOPNOTSUPP;
> -	}
> -
> -	return -EOPNOTSUPP;
> -}
> -
> -static bool usdhi6_end_cmd(struct usdhi6_host *host)
> -{
> -	struct mmc_request *mrq = host->mrq;
> -	struct mmc_command *cmd = mrq->cmd;
> -
> -	if (host->io_error) {
> -		cmd->error = usdhi6_error_code(host);
> -		return false;
> -	}
> -
> -	usdhi6_resp_read(host);
> -
> -	if (!mrq->data)
> -		return false;
> -
> -	if (host->dma_active) {
> -		usdhi6_dma_kick(host);
> -		if (!mrq->stop)
> -			host->wait = USDHI6_WAIT_FOR_DMA;
> -		else if (usdhi6_stop_cmd(host) < 0)
> -			return false;
> -	} else if (mrq->data->flags & MMC_DATA_READ) {
> -		if (cmd->opcode == MMC_READ_MULTIPLE_BLOCK ||
> -		    (cmd->opcode == SD_IO_RW_EXTENDED &&
> -		     mrq->data->blocks > 1))
> -			host->wait = USDHI6_WAIT_FOR_MREAD;
> -		else
> -			host->wait = USDHI6_WAIT_FOR_READ;
> -	} else {
> -		if (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK ||
> -		    (cmd->opcode == SD_IO_RW_EXTENDED &&
> -		     mrq->data->blocks > 1))
> -			host->wait = USDHI6_WAIT_FOR_MWRITE;
> -		else
> -			host->wait = USDHI6_WAIT_FOR_WRITE;
> -	}
> -
> -	return true;
> -}
> -
> -static bool usdhi6_read_block(struct usdhi6_host *host)
> -{
> -	/* ACCESS_END IRQ is already unmasked */
> -	int ret = usdhi6_blk_read(host);
> -
> -	/*
> -	 * Have to force unmapping both pages: the single block could have been
> -	 * cross-page, in which case for single-block IO host->page_idx == 0.
> -	 * So, if we don't force, the second page won't be unmapped.
> -	 */
> -	usdhi6_sg_unmap(host, true);
> -
> -	if (ret < 0)
> -		return false;
> -
> -	host->wait = USDHI6_WAIT_FOR_DATA_END;
> -	return true;
> -}
> -
> -static bool usdhi6_mread_block(struct usdhi6_host *host)
> -{
> -	int ret = usdhi6_blk_read(host);
> -
> -	if (ret < 0)
> -		return false;
> -
> -	usdhi6_sg_advance(host);
> -
> -	return !host->mrq->data->error &&
> -		(host->wait != USDHI6_WAIT_FOR_DATA_END || !host->mrq->stop);
> -}
> -
> -static bool usdhi6_write_block(struct usdhi6_host *host)
> -{
> -	int ret = usdhi6_blk_write(host);
> -
> -	/* See comment in usdhi6_read_block() */
> -	usdhi6_sg_unmap(host, true);
> -
> -	if (ret < 0)
> -		return false;
> -
> -	host->wait = USDHI6_WAIT_FOR_DATA_END;
> -	return true;
> -}
> -
> -static bool usdhi6_mwrite_block(struct usdhi6_host *host)
> -{
> -	int ret = usdhi6_blk_write(host);
> -
> -	if (ret < 0)
> -		return false;
> -
> -	usdhi6_sg_advance(host);
> -
> -	return !host->mrq->data->error &&
> -		(host->wait != USDHI6_WAIT_FOR_DATA_END || !host->mrq->stop);
> -}
> -
> -/*			Interrupt & timeout handlers			*/
> -
> -static irqreturn_t usdhi6_sd_bh(int irq, void *dev_id)
> -{
> -	struct usdhi6_host *host = dev_id;
> -	struct mmc_request *mrq;
> -	struct mmc_command *cmd;
> -	struct mmc_data *data;
> -	bool io_wait = false;
> -
> -	cancel_delayed_work_sync(&host->timeout_work);
> -
> -	mrq = host->mrq;
> -	if (!mrq)
> -		return IRQ_HANDLED;
> -
> -	cmd = mrq->cmd;
> -	data = mrq->data;
> -
> -	switch (host->wait) {
> -	case USDHI6_WAIT_FOR_REQUEST:
> -		/* We're too late, the timeout has already kicked in */
> -		return IRQ_HANDLED;
> -	case USDHI6_WAIT_FOR_CMD:
> -		/* Wait for data? */
> -		io_wait = usdhi6_end_cmd(host);
> -		break;
> -	case USDHI6_WAIT_FOR_MREAD:
> -		/* Wait for more data? */
> -		io_wait = usdhi6_mread_block(host);
> -		break;
> -	case USDHI6_WAIT_FOR_READ:
> -		/* Wait for data end? */
> -		io_wait = usdhi6_read_block(host);
> -		break;
> -	case USDHI6_WAIT_FOR_MWRITE:
> -		/* Wait data to write? */
> -		io_wait = usdhi6_mwrite_block(host);
> -		break;
> -	case USDHI6_WAIT_FOR_WRITE:
> -		/* Wait for data end? */
> -		io_wait = usdhi6_write_block(host);
> -		break;
> -	case USDHI6_WAIT_FOR_DMA:
> -		usdhi6_dma_check_error(host);
> -		break;
> -	case USDHI6_WAIT_FOR_STOP:
> -		usdhi6_write(host, USDHI6_SD_STOP, 0);
> -		if (host->io_error) {
> -			int ret = usdhi6_error_code(host);
> -			if (mrq->stop)
> -				mrq->stop->error = ret;
> -			else
> -				mrq->data->error = ret;
> -			dev_warn(mmc_dev(host->mmc), "%s(): %d\n", __func__, ret);
> -			break;
> -		}
> -		usdhi6_resp_cmd12(host);
> -		mrq->stop->error = 0;
> -		break;
> -	case USDHI6_WAIT_FOR_DATA_END:
> -		if (host->io_error) {
> -			mrq->data->error = usdhi6_error_code(host);
> -			dev_warn(mmc_dev(host->mmc), "%s(): %d\n", __func__,
> -				 mrq->data->error);
> -		}
> -		break;
> -	default:
> -		cmd->error = -EFAULT;
> -		dev_err(mmc_dev(host->mmc), "Invalid state %u\n", host->wait);
> -		usdhi6_request_done(host);
> -		return IRQ_HANDLED;
> -	}
> -
> -	if (io_wait) {
> -		schedule_delayed_work(&host->timeout_work, host->timeout);
> -		/* Wait for more data or ACCESS_END */
> -		if (!host->dma_active)
> -			usdhi6_wait_for_brwe(host, mrq->data->flags & MMC_DATA_READ);
> -		return IRQ_HANDLED;
> -	}
> -
> -	if (!cmd->error) {
> -		if (data) {
> -			if (!data->error) {
> -				if (host->wait != USDHI6_WAIT_FOR_STOP &&
> -				    host->mrq->stop &&
> -				    !host->mrq->stop->error &&
> -				    !usdhi6_stop_cmd(host)) {
> -					/* Sending STOP */
> -					usdhi6_wait_for_resp(host);
> -
> -					schedule_delayed_work(&host->timeout_work,
> -							      host->timeout);
> -
> -					return IRQ_HANDLED;
> -				}
> -
> -				data->bytes_xfered = data->blocks * data->blksz;
> -			} else {
> -				/* Data error: might need to unmap the last page */
> -				dev_warn(mmc_dev(host->mmc), "%s(): data error %d\n",
> -					 __func__, data->error);
> -				usdhi6_sg_unmap(host, true);
> -			}
> -		} else if (cmd->opcode == MMC_APP_CMD) {
> -			host->app_cmd = true;
> -		}
> -	}
> -
> -	usdhi6_request_done(host);
> -
> -	return IRQ_HANDLED;
> -}
> -
> -static irqreturn_t usdhi6_sd(int irq, void *dev_id)
> -{
> -	struct usdhi6_host *host = dev_id;
> -	u16 status, status2, error;
> -
> -	status = usdhi6_read(host, USDHI6_SD_INFO1) & ~host->status_mask &
> -		~USDHI6_SD_INFO1_CARD;
> -	status2 = usdhi6_read(host, USDHI6_SD_INFO2) & ~host->status2_mask;
> -
> -	usdhi6_only_cd(host);
> -
> -	dev_dbg(mmc_dev(host->mmc),
> -		"IRQ status = 0x%08x, status2 = 0x%08x\n", status, status2);
> -
> -	if (!status && !status2)
> -		return IRQ_NONE;
> -
> -	error = status2 & USDHI6_SD_INFO2_ERR;
> -
> -	/* Ack / clear interrupts */
> -	if (USDHI6_SD_INFO1_IRQ & status)
> -		usdhi6_write(host, USDHI6_SD_INFO1,
> -			     0xffff & ~(USDHI6_SD_INFO1_IRQ & status));
> -
> -	if (USDHI6_SD_INFO2_IRQ & status2) {
> -		if (error)
> -			/* In error cases BWE and BRE aren't cleared automatically */
> -			status2 |= USDHI6_SD_INFO2_BWE | USDHI6_SD_INFO2_BRE;
> -
> -		usdhi6_write(host, USDHI6_SD_INFO2,
> -			     0xffff & ~(USDHI6_SD_INFO2_IRQ & status2));
> -	}
> -
> -	host->io_error = error;
> -	host->irq_status = status;
> -
> -	if (error) {
> -		/* Don't pollute the log with unsupported command timeouts */
> -		if (host->wait != USDHI6_WAIT_FOR_CMD ||
> -		    error != USDHI6_SD_INFO2_RSP_TOUT)
> -			dev_warn(mmc_dev(host->mmc),
> -				 "%s(): INFO2 error bits 0x%08x\n",
> -				 __func__, error);
> -		else
> -			dev_dbg(mmc_dev(host->mmc),
> -				"%s(): INFO2 error bits 0x%08x\n",
> -				__func__, error);
> -	}
> -
> -	return IRQ_WAKE_THREAD;
> -}
> -
> -static irqreturn_t usdhi6_sdio(int irq, void *dev_id)
> -{
> -	struct usdhi6_host *host = dev_id;
> -	u32 status = usdhi6_read(host, USDHI6_SDIO_INFO1) & ~host->sdio_mask;
> -
> -	dev_dbg(mmc_dev(host->mmc), "%s(): status 0x%x\n", __func__, status);
> -
> -	if (!status)
> -		return IRQ_NONE;
> -
> -	usdhi6_write(host, USDHI6_SDIO_INFO1, ~status);
> -
> -	mmc_signal_sdio_irq(host->mmc);
> -
> -	return IRQ_HANDLED;
> -}
> -
> -static irqreturn_t usdhi6_cd(int irq, void *dev_id)
> -{
> -	struct usdhi6_host *host = dev_id;
> -	struct mmc_host *mmc = host->mmc;
> -	u16 status;
> -
> -	/* We're only interested in hotplug events here */
> -	status = usdhi6_read(host, USDHI6_SD_INFO1) & ~host->status_mask &
> -		USDHI6_SD_INFO1_CARD;
> -
> -	if (!status)
> -		return IRQ_NONE;
> -
> -	/* Ack */
> -	usdhi6_write(host, USDHI6_SD_INFO1, ~status);
> -
> -	if (!work_pending(&mmc->detect.work) &&
> -	    (((status & USDHI6_SD_INFO1_CARD_INSERT) &&
> -	      !mmc->card) ||
> -	     ((status & USDHI6_SD_INFO1_CARD_EJECT) &&
> -	      mmc->card)))
> -		mmc_detect_change(mmc, msecs_to_jiffies(100));
> -
> -	return IRQ_HANDLED;
> -}
> -
> -/*
> - * Actually this should not be needed, if the built-in timeout works reliably in
> - * the both PIO cases and DMA never fails. But if DMA does fail, a timeout
> - * handler might be the only way to catch the error.
> - */
> -static void usdhi6_timeout_work(struct work_struct *work)
> -{
> -	struct delayed_work *d = to_delayed_work(work);
> -	struct usdhi6_host *host = container_of(d, struct usdhi6_host, timeout_work);
> -	struct mmc_request *mrq = host->mrq;
> -	struct mmc_data *data = mrq ? mrq->data : NULL;
> -	struct scatterlist *sg;
> -
> -	dev_warn(mmc_dev(host->mmc),
> -		 "%s timeout wait %u CMD%d: IRQ 0x%08x:0x%08x, last IRQ 0x%08x\n",
> -		 host->dma_active ? "DMA" : "PIO",
> -		 host->wait, mrq ? mrq->cmd->opcode : -1,
> -		 usdhi6_read(host, USDHI6_SD_INFO1),
> -		 usdhi6_read(host, USDHI6_SD_INFO2), host->irq_status);
> -
> -	if (host->dma_active) {
> -		usdhi6_dma_kill(host);
> -		usdhi6_dma_stop_unmap(host);
> -	}
> -
> -	switch (host->wait) {
> -	default:
> -		dev_err(mmc_dev(host->mmc), "Invalid state %u\n", host->wait);
> -		fallthrough;	/* mrq can be NULL, but is impossible */
> -	case USDHI6_WAIT_FOR_CMD:
> -		usdhi6_error_code(host);
> -		if (mrq)
> -			mrq->cmd->error = -ETIMEDOUT;
> -		break;
> -	case USDHI6_WAIT_FOR_STOP:
> -		usdhi6_error_code(host);
> -		mrq->stop->error = -ETIMEDOUT;
> -		break;
> -	case USDHI6_WAIT_FOR_DMA:
> -	case USDHI6_WAIT_FOR_MREAD:
> -	case USDHI6_WAIT_FOR_MWRITE:
> -	case USDHI6_WAIT_FOR_READ:
> -	case USDHI6_WAIT_FOR_WRITE:
> -		sg = host->sg ?: data->sg;
> -		dev_dbg(mmc_dev(host->mmc),
> -			"%c: page #%u @ +0x%zx %ux%u in SG%u. Current SG %u bytes @ %u\n",
> -			data->flags & MMC_DATA_READ ? 'R' : 'W', host->page_idx,
> -			host->offset, data->blocks, data->blksz, data->sg_len,
> -			sg_dma_len(sg), sg->offset);
> -		usdhi6_sg_unmap(host, true);
> -		fallthrough;	/* page unmapped in USDHI6_WAIT_FOR_DATA_END */
> -	case USDHI6_WAIT_FOR_DATA_END:
> -		usdhi6_error_code(host);
> -		data->error = -ETIMEDOUT;
> -	}
> -
> -	if (mrq)
> -		usdhi6_request_done(host);
> -}
> -
> -/*			 Probe / release				*/
> -
> -static const struct of_device_id usdhi6_of_match[] = {
> -	{.compatible = "renesas,usdhi6rol0"},
> -	{}
> -};
> -MODULE_DEVICE_TABLE(of, usdhi6_of_match);
> -
> -static int usdhi6_probe(struct platform_device *pdev)
> -{
> -	struct device *dev = &pdev->dev;
> -	struct mmc_host *mmc;
> -	struct usdhi6_host *host;
> -	struct resource *res;
> -	int irq_cd, irq_sd, irq_sdio;
> -	u32 version;
> -	int ret;
> -
> -	if (!dev->of_node)
> -		return -ENODEV;
> -
> -	irq_cd = platform_get_irq_byname(pdev, "card detect");
> -	irq_sd = platform_get_irq_byname(pdev, "data");
> -	irq_sdio = platform_get_irq_byname(pdev, "SDIO");
> -	if (irq_sd < 0)
> -		return irq_sd;
> -	if (irq_sdio < 0)
> -		return irq_sdio;
> -
> -	mmc = devm_mmc_alloc_host(dev, sizeof(*host));
> -	if (!mmc)
> -		return -ENOMEM;
> -
> -	ret = mmc_regulator_get_supply(mmc);
> -	if (ret)
> -		return ret;
> -
> -	ret = mmc_of_parse(mmc);
> -	if (ret < 0)
> -		return ret;
> -
> -	host		= mmc_priv(mmc);
> -	host->mmc	= mmc;
> -	host->wait	= USDHI6_WAIT_FOR_REQUEST;
> -	host->timeout	= msecs_to_jiffies(USDHI6_REQ_TIMEOUT_MS);
> -	/*
> -	 * We use a fixed timeout of 4s, hence inform the core about it. A
> -	 * future improvement should instead respect the cmd->busy_timeout.
> -	 */
> -	mmc->max_busy_timeout = USDHI6_REQ_TIMEOUT_MS;
> -
> -	host->pinctrl = devm_pinctrl_get(&pdev->dev);
> -	if (IS_ERR(host->pinctrl))
> -		return PTR_ERR(host->pinctrl);
> -
> -	host->pins_uhs = pinctrl_lookup_state(host->pinctrl, "state_uhs");
> -
> -	host->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
> -	if (IS_ERR(host->base))
> -		return PTR_ERR(host->base);
> -
> -	host->clk = devm_clk_get(dev, NULL);
> -	if (IS_ERR(host->clk))
> -		return PTR_ERR(host->clk);
> -
> -	host->imclk = clk_get_rate(host->clk);
> -
> -	ret = clk_prepare_enable(host->clk);
> -	if (ret < 0)
> -		return ret;
> -
> -	version = usdhi6_read(host, USDHI6_VERSION);
> -	if ((version & 0xfff) != 0xa0d) {
> -		ret = -EPERM;
> -		dev_err(dev, "Version not recognized %x\n", version);
> -		goto e_clk_off;
> -	}
> -
> -	dev_info(dev, "A USDHI6ROL0 SD host detected with %d ports\n",
> -		 usdhi6_read(host, USDHI6_SD_PORT_SEL) >> USDHI6_SD_PORT_SEL_PORTS_SHIFT);
> -
> -	usdhi6_mask_all(host);
> -
> -	if (irq_cd >= 0) {
> -		ret = devm_request_irq(dev, irq_cd, usdhi6_cd, 0,
> -				       dev_name(dev), host);
> -		if (ret < 0)
> -			goto e_clk_off;
> -	} else {
> -		mmc->caps |= MMC_CAP_NEEDS_POLL;
> -	}
> -
> -	ret = devm_request_threaded_irq(dev, irq_sd, usdhi6_sd, usdhi6_sd_bh, 0,
> -			       dev_name(dev), host);
> -	if (ret < 0)
> -		goto e_clk_off;
> -
> -	ret = devm_request_irq(dev, irq_sdio, usdhi6_sdio, 0,
> -			       dev_name(dev), host);
> -	if (ret < 0)
> -		goto e_clk_off;
> -
> -	INIT_DELAYED_WORK(&host->timeout_work, usdhi6_timeout_work);
> -
> -	usdhi6_dma_request(host, res->start);
> -
> -	mmc->ops = &usdhi6_ops;
> -	mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
> -		     MMC_CAP_SDIO_IRQ;
> -	/* Set .max_segs to some random number. Feel free to adjust. */
> -	mmc->max_segs = 32;
> -	mmc->max_blk_size = 512;
> -	mmc->max_req_size = PAGE_SIZE * mmc->max_segs;
> -	mmc->max_blk_count = mmc->max_req_size / mmc->max_blk_size;
> -	/*
> -	 * Setting .max_seg_size to 1 page would simplify our page-mapping code,
> -	 * But OTOH, having large segments makes DMA more efficient. We could
> -	 * check, whether we managed to get DMA and fall back to 1 page
> -	 * segments, but if we do manage to obtain DMA and then it fails at
> -	 * run-time and we fall back to PIO, we will continue getting large
> -	 * segments. So, we wouldn't be able to get rid of the code anyway.
> -	 */
> -	mmc->max_seg_size = mmc->max_req_size;
> -	if (!mmc->f_max)
> -		mmc->f_max = host->imclk;
> -	mmc->f_min = host->imclk / 512;
> -
> -	platform_set_drvdata(pdev, host);
> -
> -	ret = mmc_add_host(mmc);
> -	if (ret < 0)
> -		goto e_release_dma;
> -
> -	return 0;
> -
> -e_release_dma:
> -	usdhi6_dma_release(host);
> -e_clk_off:
> -	clk_disable_unprepare(host->clk);
> -	return ret;
> -}
> -
> -static void usdhi6_remove(struct platform_device *pdev)
> -{
> -	struct usdhi6_host *host = platform_get_drvdata(pdev);
> -
> -	mmc_remove_host(host->mmc);
> -
> -	usdhi6_mask_all(host);
> -	cancel_delayed_work_sync(&host->timeout_work);
> -	usdhi6_dma_release(host);
> -	clk_disable_unprepare(host->clk);
> -}
> -
> -static struct platform_driver usdhi6_driver = {
> -	.probe		= usdhi6_probe,
> -	.remove		= usdhi6_remove,
> -	.driver		= {
> -		.name	= "usdhi6rol0",
> -		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
> -		.of_match_table = usdhi6_of_match,
> -	},
> -};
> -
> -module_platform_driver(usdhi6_driver);
> -
> -MODULE_DESCRIPTION("Renesas usdhi6rol0 SD/SDIO host driver");
> -MODULE_LICENSE("GPL v2");
> -MODULE_ALIAS("platform:usdhi6rol0");
> -MODULE_AUTHOR("Guennadi Liakhovetski <g.liakhovetski@gmx.de>");
> -- 
> 2.53.0

/^JN - Jesper Nilsson
-- 
               Jesper Nilsson -- jesper.nilsson@axis.com