[PATCH v3 2/3] i2c: algo: bit: allow getsda to be NULL

[Heiner Kallweit <hkallweit1@gmail.com>]

This is in preparation of supporting write-only SDA in i2c-gpio.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
---
v3:
- check for adap->getsda in readbytes()
- align warning message level for info on missing getscl/getsda
---
 drivers/i2c/algos/i2c-algo-bit.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/algos/i2c-algo-bit.c b/drivers/i2c/algos/i2c-algo-bit.c
index fc90293af..a1b822723 100644
--- a/drivers/i2c/algos/i2c-algo-bit.c
+++ b/drivers/i2c/algos/i2c-algo-bit.c
@@ -184,8 +184,9 @@ static int i2c_outb(struct i2c_adapter *i2c_adap, unsigned char c)
 
 	/* read ack: SDA should be pulled down by slave, or it may
 	 * NAK (usually to report problems with the data we wrote).
+	 * Always report ACK if SDA is write-only.
 	 */
-	ack = !getsda(adap);    /* ack: sda is pulled low -> success */
+	ack = !adap->getsda || !getsda(adap);    /* ack: sda is pulled low -> success */
 	bit_dbg(2, &i2c_adap->dev, "i2c_outb: 0x%02x %s\n", (int)c,
 		ack ? "A" : "NA");
 
@@ -232,6 +233,10 @@ static int test_bus(struct i2c_adapter *i2c_adap)
 	const char *name = i2c_adap->name;
 	int scl, sda, ret;
 
+	/* Testing not possible if both pins are write-only. */
+	if (adap->getscl == NULL && adap->getsda == NULL)
+		return 0;
+
 	if (adap->pre_xfer) {
 		ret = adap->pre_xfer(i2c_adap);
 		if (ret < 0)
@@ -420,6 +425,10 @@ static int readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msg)
 	unsigned char *temp = msg->buf;
 	int count = msg->len;
 	const unsigned flags = msg->flags;
+	struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
+
+	if (!adap->getsda)
+		return -EOPNOTSUPP;
 
 	while (count > 0) {
 		inval = i2c_inb(i2c_adap);
@@ -670,8 +679,11 @@ static int __i2c_bit_add_bus(struct i2c_adapter *adap,
 	if (ret < 0)
 		return ret;
 
-	/* Complain if SCL can't be read */
+	if (bit_adap->getsda == NULL)
+		dev_warn(&adap->dev, "Not I2C compliant: can't read SDA\n");
+
 	if (bit_adap->getscl == NULL) {
+		/* Complain if SCL can't be read */
 		dev_warn(&adap->dev, "Not I2C compliant: can't read SCL\n");
 		dev_warn(&adap->dev, "Bus may be unreliable\n");
 	}
-- 
2.39.0