* [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
@ 2024-10-02 8:40 Naresh Solanki
2024-10-02 8:40 ` [PATCH v3 2/2] ARM: dts: aspeed: sbp1: IBM sbp1 BMC board Naresh Solanki
` (3 more replies)
0 siblings, 4 replies; 8+ messages in thread
From: Naresh Solanki @ 2024-10-02 8:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel
Cc: Naresh Solanki
Document the new compatibles used on IBM SBP1.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
---
Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index 95113df178cc..8c04d6eaec08 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -89,6 +89,7 @@ properties:
- ibm,everest-bmc
- ibm,rainier-bmc
- ibm,system1-bmc
+ - ibm,sbp1-bmc
- ibm,tacoma-bmc
- inventec,starscream-bmc
- inventec,transformer-bmc
--
2.42.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v3 2/2] ARM: dts: aspeed: sbp1: IBM sbp1 BMC board
2024-10-02 8:40 [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Naresh Solanki
@ 2024-10-02 8:40 ` Naresh Solanki
2024-10-02 21:45 ` [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Rob Herring (Arm)
` (2 subsequent siblings)
3 siblings, 0 replies; 8+ messages in thread
From: Naresh Solanki @ 2024-10-02 8:40 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel
Cc: Patrick Rudolph, Naresh Solanki
From: Patrick Rudolph <patrick.rudolph@9elements.com>
Add a device tree for IBM sbp1 BMC board which is based on AST2600 SOC.
sbp1 baseboard has:
- support for up to four Sapphire Rapids sockets having 16 DIMMS each.
- 240 core/480 threads at maximum
- 32x CPU PCIe slots
- 2x M.2 PCH PCIe slots
- Dual 200Gbit/s NIC
- SPI TPM
Added the following:
- Indication LEDs
- I2C mux & GPIO controller, pin assignments,
- Thermister,
- Voltage regulator
- EEPROM/VPD
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
---
Changes in V3:
Drop unused regulator entries which are not used by drivers.
Decouple p12v_a
Update pincfg for U62120
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts | 6132 +++++++++++++++++
2 files changed, 6133 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index e51c6d203725..06701080362c 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-ibm-rainier-1s4u.dtb \
aspeed-bmc-ibm-rainier-4u.dtb \
aspeed-bmc-ibm-system1.dtb \
+ aspeed-bmc-ibm-sbp1.dtb \
aspeed-bmc-intel-s2600wf.dtb \
aspeed-bmc-inspur-fp5280g2.dtb \
aspeed-bmc-inspur-nf5280m6.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
new file mode 100644
index 000000000000..76d33c336fce
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
@@ -0,0 +1,6132 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/i2c/i2c.h>
+#include "aspeed-g6.dtsi"
+
+/ {
+ model = "IBM SBP1";
+ compatible = "ibm,sbp1-bmc", "aspeed,ast2600";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory@80000000 {
+ reg = <0x80000000 0x20000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-power {
+ label = "LED_BMC_READY";
+ gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ retain-state-suspended;
+ panic-indicator;
+ };
+
+ led-id-tpm {
+ label = "LED_ID_TPM";
+ gpios = <&smb_pex_vr_ctrl 12 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-bat {
+ label = "LED_ID_BAT";
+ gpios = <&smb_pex_vr_ctrl 16 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-mgmt-port2 {
+ label = "LED_ID_MGMT_PORT2";
+ gpios = <&smb_pex_vr_ctrl 17 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-mgmt-port1 {
+ label = "LED_ID_MGMT_PORT1";
+ gpios = <&smb_pex_vr_ctrl 18 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-nic1-port1 {
+ label = "LED_ID_NIC1_PORT1";
+ gpios = <&smb_pex_vr_ctrl 22 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-nic1-port2 {
+ label = "LED_ID_NIC1_PORT2";
+ gpios = <&smb_pex_vr_ctrl 23 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-nic2-port1 {
+ label = "LED_ID_NIC2_PORT1";
+ gpios = <&smb_pex_vr_ctrl 24 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-nic2-port2 {
+ label = "LED_ID_NIC2_PORT2";
+ gpios = <&smb_pex_vr_ctrl 25 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-m2-ssd2 {
+ label = "LED_ID_M2_SSD2";
+ gpios = <&smb_pex_vr_ctrl 36 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-m2-ssd1 {
+ label = "LED_ID_M2_SSD1";
+ gpios = <&smb_pex_vr_ctrl 37 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dwr-frnt-p {
+ label = "LED_ID_DWR_FRNT_P";
+ gpios = <&smb_svc_pex_cpu3_led 37 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+
+ default-state = "on";
+ retain-state-suspended;
+ retain-state-shutdown;
+ };
+
+ led-pwr-dwr-frnt {
+ label = "LED_PWR_DWR_FRNT";
+ gpios = <&smb_svc_pex_cpu3_led 36 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+
+ retain-state-suspended;
+ retain-state-shutdown;
+ };
+
+ led-pwr-dwr-back {
+ label = "LED_PWR_DWR_BACK";
+ gpios = <&smb_pex_vr_ctrl 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+
+ retain-state-suspended;
+ retain-state-shutdown;
+ };
+
+ led-id-dwr-back-p {
+ label = "LED_ID_DWR_BACK_P";
+ gpios = <&smb_pex_vr_ctrl 35 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+
+ default-state = "on";
+ retain-state-suspended;
+ retain-state-shutdown;
+ };
+
+ led-id-cpu0 {
+ label = "LED_ID_CPU0";
+ gpios = <&smb_svc_pex_cpu0_led 39 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-cpu1 {
+ label = "LED_ID_CPU1";
+ gpios = <&smb_svc_pex_cpu1_led 39 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-cpu2 {
+ label = "LED_ID_CPU2";
+ gpios = <&smb_svc_pex_cpu2_led 39 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-cpu3 {
+ label = "LED_ID_CPU3";
+ gpios = <&smb_svc_pex_cpu3_led 39 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0e2 {
+ label = "LED_ID_DIMM_C0E2";
+ gpios = <&smb_svc_pex_cpu0_led 20 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0e1 {
+ label = "LED_ID_DIMM_C0E1";
+ gpios = <&smb_svc_pex_cpu0_led 21 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0f2 {
+ label = "LED_ID_DIMM_C0F2";
+ gpios = <&smb_svc_pex_cpu0_led 22 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0f1 {
+ label = "LED_ID_DIMM_C0F1";
+ gpios = <&smb_svc_pex_cpu0_led 23 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0g2 {
+ label = "LED_ID_DIMM_C0G2";
+ gpios = <&smb_svc_pex_cpu0_led 24 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0g1 {
+ label = "LED_ID_DIMM_C0G1";
+ gpios = <&smb_svc_pex_cpu0_led 25 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0h2 {
+ label = "LED_ID_DIMM_C0H2";
+ gpios = <&smb_svc_pex_cpu0_led 26 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0h1 {
+ label = "LED_ID_DIMM_C0H1";
+ gpios = <&smb_svc_pex_cpu0_led 27 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0a2 {
+ label = "LED_ID_DIMM_C0A2";
+ gpios = <&smb_svc_pex_cpu0_led 28 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0a1 {
+ label = "LED_ID_DIMM_C0A1";
+ gpios = <&smb_svc_pex_cpu0_led 29 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0b2 {
+ label = "LED_ID_DIMM_C0B2";
+ gpios = <&smb_svc_pex_cpu0_led 30 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0b1 {
+ label = "LED_ID_DIMM_C0B1";
+ gpios = <&smb_svc_pex_cpu0_led 31 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0c2 {
+ label = "LED_ID_DIMM_C0C2";
+ gpios = <&smb_svc_pex_cpu0_led 32 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0c1 {
+ label = "LED_ID_DIMM_C0C1";
+ gpios = <&smb_svc_pex_cpu0_led 33 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0d2 {
+ label = "LED_ID_DIMM_C0D2";
+ gpios = <&smb_svc_pex_cpu0_led 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c0d1 {
+ label = "LED_ID_DIMM_C0D1";
+ gpios = <&smb_svc_pex_cpu0_led 35 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1e2 {
+ label = "LED_ID_DIMM_C1E2";
+ gpios = <&smb_svc_pex_cpu1_led 20 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1e1 {
+ label = "LED_ID_DIMM_C1E1";
+ gpios = <&smb_svc_pex_cpu1_led 21 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1f2 {
+ label = "LED_ID_DIMM_C1F2";
+ gpios = <&smb_svc_pex_cpu1_led 22 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1f1 {
+ label = "LED_ID_DIMM_C1F1";
+ gpios = <&smb_svc_pex_cpu1_led 23 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1g2 {
+ label = "LED_ID_DIMM_C1G2";
+ gpios = <&smb_svc_pex_cpu1_led 24 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1g1 {
+ label = "LED_ID_DIMM_C1G1";
+ gpios = <&smb_svc_pex_cpu1_led 25 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1h2 {
+ label = "LED_ID_DIMM_C1H2";
+ gpios = <&smb_svc_pex_cpu1_led 26 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1h1 {
+ label = "LED_ID_DIMM_C1H1";
+ gpios = <&smb_svc_pex_cpu1_led 27 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1a2 {
+ label = "LED_ID_DIMM_C1A2";
+ gpios = <&smb_svc_pex_cpu1_led 28 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1a1 {
+ label = "LED_ID_DIMM_C1A1";
+ gpios = <&smb_svc_pex_cpu1_led 29 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1b2 {
+ label = "LED_ID_DIMM_C1B2";
+ gpios = <&smb_svc_pex_cpu1_led 30 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1b1 {
+ label = "LED_ID_DIMM_C1B1";
+ gpios = <&smb_svc_pex_cpu1_led 31 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1c2 {
+ label = "LED_ID_DIMM_C1C2";
+ gpios = <&smb_svc_pex_cpu1_led 32 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1c1 {
+ label = "LED_ID_DIMM_C1C1";
+ gpios = <&smb_svc_pex_cpu1_led 33 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1d2 {
+ label = "LED_ID_DIMM_C1D2";
+ gpios = <&smb_svc_pex_cpu1_led 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c1d1 {
+ label = "LED_ID_DIMM_C1D1";
+ gpios = <&smb_svc_pex_cpu1_led 35 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2e2 {
+ label = "LED_ID_DIMM_C2E2";
+ gpios = <&smb_svc_pex_cpu2_led 20 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2e1 {
+ label = "LED_ID_DIMM_C2E1";
+ gpios = <&smb_svc_pex_cpu2_led 21 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2f2 {
+ label = "LED_ID_DIMM_C2F2";
+ gpios = <&smb_svc_pex_cpu2_led 22 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2f1 {
+ label = "LED_ID_DIMM_C2F1";
+ gpios = <&smb_svc_pex_cpu2_led 23 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2g2 {
+ label = "LED_ID_DIMM_C2G2";
+ gpios = <&smb_svc_pex_cpu2_led 24 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2g1 {
+ label = "LED_ID_DIMM_C2G1";
+ gpios = <&smb_svc_pex_cpu2_led 25 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2h2 {
+ label = "LED_ID_DIMM_C2H2";
+ gpios = <&smb_svc_pex_cpu2_led 26 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2h1 {
+ label = "LED_ID_DIMM_C2H1";
+ gpios = <&smb_svc_pex_cpu2_led 27 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2a2 {
+ label = "LED_ID_DIMM_C2A2";
+ gpios = <&smb_svc_pex_cpu2_led 28 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2a1 {
+ label = "LED_ID_DIMM_C2A1";
+ gpios = <&smb_svc_pex_cpu2_led 29 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2b2 {
+ label = "LED_ID_DIMM_C2B2";
+ gpios = <&smb_svc_pex_cpu2_led 30 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2b1 {
+ label = "LED_ID_DIMM_C2B1";
+ gpios = <&smb_svc_pex_cpu2_led 31 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2c2 {
+ label = "LED_ID_DIMM_C2C2";
+ gpios = <&smb_svc_pex_cpu2_led 32 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2c1 {
+ label = "LED_ID_DIMM_C2C1";
+ gpios = <&smb_svc_pex_cpu2_led 33 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2d2 {
+ label = "LED_ID_DIMM_C2D2";
+ gpios = <&smb_svc_pex_cpu2_led 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c2d1 {
+ label = "LED_ID_DIMM_C2D1";
+ gpios = <&smb_svc_pex_cpu2_led 35 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3e2 {
+ label = "LED_ID_DIMM_C3E2";
+ gpios = <&smb_svc_pex_cpu3_led 20 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3e1 {
+ label = "LED_ID_DIMM_C3E1";
+ gpios = <&smb_svc_pex_cpu3_led 21 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3f2 {
+ label = "LED_ID_DIMM_C3F2";
+ gpios = <&smb_svc_pex_cpu3_led 22 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3f1 {
+ label = "LED_ID_DIMM_C3F1";
+ gpios = <&smb_svc_pex_cpu3_led 23 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3g2 {
+ label = "LED_ID_DIMM_C3G2";
+ gpios = <&smb_svc_pex_cpu3_led 24 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3g1 {
+ label = "LED_ID_DIMM_C3G1";
+ gpios = <&smb_svc_pex_cpu3_led 25 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3h2 {
+ label = "LED_ID_DIMM_C3H2";
+ gpios = <&smb_svc_pex_cpu3_led 26 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3h1 {
+ label = "LED_ID_DIMM_C3H1";
+ gpios = <&smb_svc_pex_cpu3_led 27 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3a2 {
+ label = "LED_ID_DIMM_C3A2";
+ gpios = <&smb_svc_pex_cpu3_led 28 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3a1 {
+ label = "LED_ID_DIMM_C3A1";
+ gpios = <&smb_svc_pex_cpu3_led 29 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3b2 {
+ label = "LED_ID_DIMM_C3B2";
+ gpios = <&smb_svc_pex_cpu3_led 30 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3b1 {
+ label = "LED_ID_DIMM_C3B1";
+ gpios = <&smb_svc_pex_cpu3_led 31 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3c2 {
+ label = "LED_ID_DIMM_C3C2";
+ gpios = <&smb_svc_pex_cpu3_led 32 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3c1 {
+ label = "LED_ID_DIMM_C3C1";
+ gpios = <&smb_svc_pex_cpu3_led 33 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3d2 {
+ label = "LED_ID_DIMM_C3D2";
+ gpios = <&smb_svc_pex_cpu3_led 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-c3d1 {
+ label = "LED_ID_DIMM_C3D1";
+ gpios = <&smb_svc_pex_cpu3_led 35 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd01 {
+ label = "LED_ID_RSSD01";
+ gpios = <&smb_svc_pex_rssd01_16 0 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd02 {
+ label = "LED_ID_RSSD02";
+ gpios = <&smb_svc_pex_rssd01_16 1 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd03 {
+ label = "LED_ID_RSSD03";
+ gpios = <&smb_svc_pex_rssd01_16 2 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd04 {
+ label = "LED_ID_RSSD04";
+ gpios = <&smb_svc_pex_rssd01_16 3 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd05 {
+ label = "LED_ID_RSSD05";
+ gpios = <&smb_svc_pex_rssd01_16 4 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd06 {
+ label = "LED_ID_RSSD06";
+ gpios = <&smb_svc_pex_rssd01_16 5 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd07 {
+ label = "LED_ID_RSSD07";
+ gpios = <&smb_svc_pex_rssd01_16 6 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd08 {
+ label = "LED_ID_RSSD08";
+ gpios = <&smb_svc_pex_rssd01_16 7 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd09 {
+ label = "LED_ID_RSSD09";
+ gpios = <&smb_svc_pex_rssd01_16 8 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd10 {
+ label = "LED_ID_RSSD10";
+ gpios = <&smb_svc_pex_rssd01_16 9 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd11 {
+ label = "LED_ID_RSSD11";
+ gpios = <&smb_svc_pex_rssd01_16 10 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd12 {
+ label = "LED_ID_RSSD12";
+ gpios = <&smb_svc_pex_rssd01_16 11 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd13 {
+ label = "LED_ID_RSSD13";
+ gpios = <&smb_svc_pex_rssd01_16 12 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd14 {
+ label = "LED_ID_RSSD14";
+ gpios = <&smb_svc_pex_rssd01_16 13 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd15 {
+ label = "LED_ID_RSSD15";
+ gpios = <&smb_svc_pex_rssd01_16 14 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd16 {
+ label = "LED_ID_RSSD16";
+ gpios = <&smb_svc_pex_rssd01_16 15 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd17 {
+ label = "LED_ID_RSSD17";
+ gpios = <&smb_svc_pex_rssd17_32 0 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd18 {
+ label = "LED_ID_RSSD18";
+ gpios = <&smb_svc_pex_rssd17_32 1 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd19 {
+ label = "LED_ID_RSSD19";
+ gpios = <&smb_svc_pex_rssd17_32 2 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd20 {
+ label = "LED_ID_RSSD20";
+ gpios = <&smb_svc_pex_rssd17_32 3 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd21 {
+ label = "LED_ID_RSSD21";
+ gpios = <&smb_svc_pex_rssd17_32 4 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd22 {
+ label = "LED_ID_RSSD22";
+ gpios = <&smb_svc_pex_rssd17_32 5 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd23 {
+ label = "LED_ID_RSSD23";
+ gpios = <&smb_svc_pex_rssd17_32 6 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd24 {
+ label = "LED_ID_RSSD24";
+ gpios = <&smb_svc_pex_rssd17_32 7 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd25 {
+ label = "LED_ID_RSSD25";
+ gpios = <&smb_svc_pex_rssd17_32 8 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd26 {
+ label = "LED_ID_RSSD26";
+ gpios = <&smb_svc_pex_rssd17_32 9 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd27 {
+ label = "LED_ID_RSSD27";
+ gpios = <&smb_svc_pex_rssd17_32 10 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd28 {
+ label = "LED_ID_RSSD28";
+ gpios = <&smb_svc_pex_rssd17_32 11 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd29 {
+ label = "LED_ID_RSSD29";
+ gpios = <&smb_svc_pex_rssd17_32 12 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd30 {
+ label = "LED_ID_RSSD30";
+ gpios = <&smb_svc_pex_rssd17_32 13 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd31 {
+ label = "LED_ID_RSSD31";
+ gpios = <&smb_svc_pex_rssd17_32 14 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-dimm-rssd32 {
+ label = "LED_ID_RSSD32";
+ gpios = <&smb_svc_pex_rssd17_32 15 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm01 {
+ label = "LED_ID_FAN_ASM01";
+ gpios = <&smb_svc_pex_rssd01_16 32 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm02 {
+ label = "LED_ID_FAN_ASM02";
+ gpios = <&smb_svc_pex_rssd01_16 33 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm03 {
+ label = "LED_ID_FAN_ASM03";
+ gpios = <&smb_svc_pex_rssd01_16 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm04 {
+ label = "LED_ID_FAN_ASM04";
+ gpios = <&smb_svc_pex_rssd01_16 35 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm05 {
+ label = "LED_ID_FAN_ASM05";
+ gpios = <&smb_svc_pex_rssd01_16 36 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm06 {
+ label = "LED_ID_FAN_ASM06";
+ gpios = <&smb_svc_pex_rssd01_16 37 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm07 {
+ label = "LED_ID_FAN_ASM07";
+ gpios = <&smb_svc_pex_rssd17_32 32 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm08 {
+ label = "LED_ID_FAN_ASM08";
+ gpios = <&smb_svc_pex_rssd17_32 33 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm09 {
+ label = "LED_ID_FAN_ASM09";
+ gpios = <&smb_svc_pex_rssd17_32 34 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm10 {
+ label = "LED_ID_FAN_ASM10";
+ gpios = <&smb_svc_pex_rssd17_32 35 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm11 {
+ label = "LED_ID_FAN_ASM11";
+ gpios = <&smb_svc_pex_rssd17_32 36 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+
+ led-id-fan-asm12 {
+ label = "LED_ID_FAN_ASM12";
+ gpios = <&smb_svc_pex_rssd17_32 37 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_YELLOW>;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&p12v_vd 0>, <&p5v_aux_vd 0>, <&p5v_bmc_aux_vd 0>, <&p3v3_aux_vd 0>,
+ <&p3v3_bmc_aux_vd 0>, <&p1v8_bmc_aux_vd 0>, <&adc1 4>, <&adc0 2>, <&adc1 0>,
+ <&p2V5_aux_vd 0>, <&p3v3_rtc_vd 0>;
+ };
+
+ p12v_vd: voltage-divider1 {
+ compatible = "voltage-divider";
+ io-channels = <&adc1 3>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 1127/127 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <15>;
+ full-ohms = <133>;
+ };
+
+ p5v_aux_vd: voltage-divider2 {
+ compatible = "voltage-divider";
+ io-channels = <&adc1 5>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 1365/365 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <50>;
+ full-ohms = <187>;
+ };
+
+ p5v_bmc_aux_vd: voltage-divider3 {
+ compatible = "voltage-divider";
+ io-channels = <&adc0 3>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 1365/365 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <50>;
+ full-ohms = <187>;
+ };
+
+ p3v3_aux_vd: voltage-divider4 {
+ compatible = "voltage-divider";
+ io-channels = <&adc1 2>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 1698/698 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <14>;
+ full-ohms = <34>;
+ };
+
+ p3v3_bmc_aux_vd: voltage-divider5 {
+ compatible = "voltage-divider";
+ io-channels = <&adc0 7>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 1698/698 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <14>;
+ full-ohms = <34>;
+ };
+
+ p1v8_bmc_aux_vd: voltage-divider6 {
+ compatible = "voltage-divider";
+ io-channels = <&adc0 6>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 4000/3000 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <3>;
+ full-ohms = <4>;
+ };
+
+ p2V5_aux_vd: voltage-divider7 {
+ compatible = "voltage-divider";
+ io-channels = <&adc1 1>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 2100/1100 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <11>;
+ full-ohms = <21>;
+ };
+
+ p3v3_rtc_vd: voltage-divider8 {
+ compatible = "voltage-divider";
+ io-channels = <&adc1 7>;
+ #io-channel-cells = <1>;
+
+ /*
+ * Scale the system voltage by 231000/100000 to fit the ADC range.
+ * Use small nominator to prevent integer overflow.
+ */
+ output-ohms = <100>;
+ full-ohms = <231>;
+ };
+
+ thermistor0: thermistor-0 {
+ compatible = "epcos,b57891s0103";
+ pullup-uv = <3300000>;
+ pullup-ohm = <10000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc0 0>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermistor1: thermistor-1 {
+ compatible = "epcos,b57891s0103";
+ pullup-uv = <3300000>;
+ pullup-ohm = <10000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc0 1>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermistor2: thermistor-2 {
+ compatible = "epcos,b57891s0103";
+ pullup-uv = <3300000>;
+ pullup-ohm = <10000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc0 4>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermistor3: thermistor-3 {
+ compatible = "epcos,b57891s0103";
+ pullup-uv = <3300000>;
+ pullup-ohm = <10000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc0 5>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ p12v: fixedregulator-p12v {
+ compatible = "regulator-fixed";
+ regulator-name = "p12v";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ p3v3_bmc_aux: fixedregulator-p3v3-bmc-aux {
+ compatible = "regulator-fixed";
+ regulator-name = "p3v3_bmc_aux";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ p1v8_bmc_aux: fixedregulator-p1v8-bmc-aux {
+ compatible = "regulator-fixed";
+ regulator-name = "p1v8_bmc_aux";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ p1v2_bmc_aux: fixedregulator-p1v2-bmc-aux {
+ compatible = "regulator-fixed";
+ regulator-name = "p1v2_bmc_aux";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ p12v-a-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p12v_a>;
+ };
+
+ p12v-b-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p12v_b>;
+ };
+
+ p12v-c-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p12v_c>;
+ };
+
+ p12v-d-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p12v_d>;
+ };
+
+ pvccinfaon-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccinfaon_cpu0>;
+ };
+
+ pvccfa-ehv-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_cpu0>;
+ };
+
+ pvnn-main-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvnn_main_cpu0>;
+ };
+
+ pvccin-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccin_cpu0>;
+ };
+
+ pvccfa-ehv-fivra-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_fivra_cpu0>;
+ };
+
+ pvccd-hv-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccd_hv_cpu0>;
+ };
+
+ pvpp-hbm-cpu0-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvpp_hbm_cpu0>;
+ };
+
+ pvccinfaon-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccinfaon_cpu1>;
+ };
+
+ pvccfa-ehv-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_cpu1>;
+ };
+
+ pvnn-main-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvnn_main_cpu1>;
+ };
+
+ pvccin-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccin_cpu1>;
+ };
+
+ pvccfa-ehv-fivra-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_fivra_cpu1>;
+ };
+
+ pvccd-hv-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccd_hv_cpu1>;
+ };
+
+ pvpp-hbm-cpu1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvpp_hbm_cpu1>;
+ };
+
+ pvccinfaon-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccinfaon_cpu2>;
+ };
+
+ pvccfa-ehv-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_cpu2>;
+ };
+
+ pvnn-main-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvnn_main_cpu2>;
+ };
+
+ pvccin-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccin_cpu2>;
+ };
+
+ pvccfa-ehv-fivra-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_fivra_cpu2>;
+ };
+
+ pvccd-hv-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccd_hv_cpu2>;
+ };
+
+ pvpp-hbm-cpu2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvpp_hbm_cpu2>;
+ };
+
+ pvccinfaon-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccinfaon_cpu3>;
+ };
+
+ pvccfa-ehv-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_cpu3>;
+ };
+
+ pvnn-main-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvnn_main_cpu3>;
+ };
+
+ pvccin-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccin_cpu3>;
+ };
+
+ pvccfa-ehv-fivra-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccfa_ehv_fivra_cpu3>;
+ };
+
+ pvccd-hv-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvccd_hv_cpu3>;
+ };
+
+ pvpp-hbm-cpu3-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvpp_hbm_cpu3>;
+ };
+
+ p1v05-pch-aux-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p1v05_pch_aux>;
+ };
+
+ p1v8-pch-aux-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p1v8_pch_aux>;
+ };
+
+ p3v3-pch-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p3v3_pch>;
+ };
+
+ p5v-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p5v>;
+ };
+
+ smb-m2-ssb-ssd2 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_smb_m2_ssb_ssd2>;
+ };
+
+ smb-m2-ssb-ssd1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_smb_m2_ssb_ssd1>;
+ };
+
+ ssb-rssd01-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd01>;
+ };
+
+ ssb-rssd01-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd01>;
+ };
+
+ ssb-rssd02-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd02>;
+ };
+
+ ssb-rssd02-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd02>;
+ };
+
+ ssb-rssd03-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd03>;
+ };
+
+ ssb-rssd03-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd03>;
+ };
+
+ ssb-rssd04-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd04>;
+ };
+
+ ssb-rssd04-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd04>;
+ };
+
+ ssb-rssd05-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd05>;
+ };
+
+ ssb-rssd05-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd05>;
+ };
+
+ ssb-rssd06-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd06>;
+ };
+
+ ssb-rssd06-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd06>;
+ };
+
+ ssb-rssd07-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd07>;
+ };
+
+ ssb-rssd07-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd07>;
+ };
+
+ ssb-rssd08-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd08>;
+ };
+
+ ssb-rssd08-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd08>;
+ };
+
+ ssb-rssd09-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd09>;
+ };
+
+ ssb-rssd09-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd09>;
+ };
+
+ ssb-rssd10-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd10>;
+ };
+
+ ssb-rssd10-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd10>;
+ };
+
+ ssb-rssd11-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd11>;
+ };
+
+ ssb-rssd11-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd11>;
+ };
+
+ ssb-rssd12-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd12>;
+ };
+
+ ssb-rssd12-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd12>;
+ };
+
+ ssb-rssd13-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd13>;
+ };
+
+ ssb-rssd13-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd13>;
+ };
+
+ ssb-rssd14-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd14>;
+ };
+
+ ssb-rssd14-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd14>;
+ };
+
+ ssb-rssd15-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd15>;
+ };
+
+ ssb-rssd15-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd15>;
+ };
+
+ ssb-rssd16-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd16>;
+ };
+
+ ssb-rssd16-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd16>;
+ };
+
+ ssb-rssd17-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd17>;
+ };
+
+ ssb-rssd17-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd17>;
+ };
+
+ ssb-rssd18-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd18>;
+ };
+
+ ssb-rssd18-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd18>;
+ };
+
+ ssb-rssd19-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd19>;
+ };
+
+ ssb-rssd19-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd19>;
+ };
+
+ ssb-rssd20-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd20>;
+ };
+
+ ssb-rssd20-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd20>;
+ };
+
+ ssb-rssd21-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd21>;
+ };
+
+ ssb-rssd21-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd21>;
+ };
+
+ ssb-rssd22-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd22>;
+ };
+
+ ssb-rssd22-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd22>;
+ };
+
+ ssb-rssd23-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd23>;
+ };
+
+ ssb-rssd23-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd23>;
+ };
+
+ ssb-rssd24-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd24>;
+ };
+
+ ssb-rssd24-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd24>;
+ };
+
+ ssb-rssd25-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd25>;
+ };
+
+ ssb-rssd25-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd25>;
+ };
+
+ ssb-rssd26-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd26>;
+ };
+
+ ssb-rssd26-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd26>;
+ };
+
+ ssb-rssd27-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd27>;
+ };
+
+ ssb-rssd27-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd27>;
+ };
+
+ ssb-rssd28-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd28>;
+ };
+
+ ssb-rssd28-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd28>;
+ };
+
+ ssb-rssd29-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd29>;
+ };
+
+ ssb-rssd29-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd29>;
+ };
+
+ ssb-rssd30-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd30>;
+ };
+
+ ssb-rssd30-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd30>;
+ };
+
+ ssb-rssd31-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd31>;
+ };
+
+ ssb-rssd31-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd31>;
+ };
+
+ ssb-rssd32-sw0 {
+ compatible = "regulator-output";
+ vout-supply = <&sw0_ssb_rssd32>;
+ };
+
+ ssb-rssd32-sw1 {
+ compatible = "regulator-output";
+ vout-supply = <&sw1_ssb_rssd32>;
+ };
+
+ p3v3-nic-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p3v3_nic>;
+ };
+
+ p1v8-nic-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p1v8_nic>;
+ };
+
+ p1v2-nic-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&p1v2_nic>;
+ };
+
+ pvcore-nic1-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvcore_nic1>;
+ };
+
+ pvcore-nic2-consumer {
+ compatible = "regulator-output";
+ vout-supply = <&pvcore_nic2>;
+ };
+};
+
+&peci0 {
+ status = "okay";
+};
+
+&vuart1 {
+ status = "okay";
+};
+
+&lpc_snoop {
+ status = "okay";
+ snoop-ports = <0x80>, <0x81>;
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+#include "openbmc-flash-layout-64.dtsi"
+ };
+
+ flash@1 {
+ status = "okay";
+ m25p,fast-read;
+ label = "alt-bmc";
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+ };
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default
+ &pinctrl_nrts1_default
+ &pinctrl_ndtr1_default
+ &pinctrl_ndsr1_default
+ &pinctrl_ncts1_default
+ &pinctrl_ndcd1_default
+ &pinctrl_nri1_default>;
+};
+
+&uart5 {
+ status = "disabled";
+};
+
+&gpio1 {
+ status = "disabled";
+};
+
+&video {
+ status = "okay";
+};
+
+&vhub {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_vgahs_default &pinctrl_vgavs_default>;
+};
+
+&mdio2 {
+ status = "okay";
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(V, 7) GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+
+ ethphy2: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio3 {
+ status = "okay";
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+
+ ethphy3: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mac2 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ phy-handle = <ðphy2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ phy-handle = <ðphy3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&adc0 {
+ status = "okay";
+ vref-supply = <&p1v8_bmc_aux>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default
+ &pinctrl_adc1_default
+ &pinctrl_adc2_default
+ &pinctrl_adc3_default
+ &pinctrl_adc4_default
+ &pinctrl_adc5_default
+ &pinctrl_adc6_default
+ &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ status = "okay";
+ vref-supply = <&p1v8_bmc_aux>;
+ aspeed,battery-sensing;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc8_default
+ &pinctrl_adc9_default
+ &pinctrl_adc10_default
+ &pinctrl_adc11_default
+ &pinctrl_adc12_default
+ &pinctrl_adc13_default
+ &pinctrl_adc15_default>;
+};
+
+&kcs3 {
+ status = "okay";
+ aspeed,lpc-io-reg = <0xca2>;
+};
+
+&gpio0 {
+ status = "okay";
+ gpio-line-names =
+ /* A0 - A7 */
+ "", "", "", "", "", "", "", "",
+ /* B0 - B7 */
+ "", "", "FM_ADR_TRIGGER_R_N", "RST_PLTRST_BUF_N", "BMC_TPM_RESET_N", "BMC_TPM_IRQ_N",
+ "PCH_TPM_RESET_N", "PCH_TPM_IRQ_N",
+ /* C0 - C7 */
+ "", "", "", "", "", "", "", "",
+ /* D0 - D7 */
+ "", "", "", "", "", "", "", "",
+ /* E0 - E7 */
+ "", "", "", "", "", "", "", "",
+ /* F0 - F7 */
+ "", "", "", "BMC_MUX_CPU1_RST_INT_N", "BMC_MUX_CPU2_RST_INT_N", "", "", "",
+ /* G0 - G7 */
+ "FM_SSD_CLK_DRVR1_EN", "FM_CK440Q_DEV_EN", "BMC_MAC1_RESET_N", "FM_DB2000_DEV_EN",
+ "FM_CPU_RMCA_LVT3_N", "FM_CPU_CATERR_LVT3_N", "FM_DBP_PRESENT_N", "",
+ /* H0 - H7 */
+ "SMB_SVC_PEX_RSSD17_32_INT", "LED_BMC_RDY", "RST_DBP_N", "", "", "", "", "",
+ /* I0 - I7 */
+ "JTAG_MUX_MODE_SEL", "JTAG_MUX_TRANS_ENBL", "JTAG_MUX_LSP_SEL5", "JTAG_MUX_MSTR_SEL",
+ "JTAG_MUX_LSP_SEL3", "", "JTAG_MUX_ENBL_N", "JTAG_MUX_RST_N",
+ /* J0 - J7 */
+ "", "", "", "", "", "", "", "",
+ /* K0 - K7 */
+ "", "", "", "", "", "", "", "",
+ /* L0 - L7 */
+ "", "", "", "", "RST_RTCRST_N", "RST_SRTCRST_N", "", "",
+ /* M0 - M7 */
+ "BMC_UART1_CTS_N", "BMC_UART1_DCD_N", "BMC_UART1_DSR_N", "BMC_UART1_RI_N",
+ "BMC_UART1_DTR_N", "BMC_UART1_RTS_N", "", "",
+ /* N0 - N7 */
+ "IRQ_BMC_PCH_NMI", "", "FM_PCH_BMC_THERMTRIP_N", "FM_BIOS_POST_CMPLT_N", "RST_PLTRST_N",
+ "FM_FLASH_SEC_OVRD", "FM_SMI_ACTIVE_N", "PWRGD_DBP",
+ /* O0 - O7 */
+ "CATERR_CPU2_EN", "H_LVT1_THERMTRIP_N", "CATERR_CPU3_EN", "SMB_SVC_PEX_CPU0_LED_INT",
+ "H_LVT1_MEMTRIP_N", "", "CATERR_CPU1_EN", "FM_PCH_ADR_COMPLETE_N",
+ /* P0 - P7 */
+ "PWRGD_SYS_PWROK", "PWRGD_PCH_PWROK", "BMC_MUX_CPU3_RST_INT_N", "BMC_MUX_SVC_RSSD_INT",
+ "FM_SLPS4_N", "IRQ_SML0_ALERT_N", "FM_SLPS3_N", "LED_BMC_HB",
+ /* Q0 - Q7 */
+ "", "PEX_BMC_RST", "PEX_VR_CTRL_RST", "PEX_NIC_RST", "PEX_CPU0_LED_RST", "PEX_CPU1_LED_RST",
+ "PEX_CPU2_LED_RST", "PEX_CPU3_LED_RST",
+ /* R0 - R7 */
+ "BMC_MUX_FANSSB_RSSD17_32_RST_INT_N", "BMC_MUX_FANPWM_RSSD01_16_RST_INT_N",
+ "BMC_MUX_SVC_VR_RST_INT_N", "BMC_MUX_NIC_RST_INT_N", "BMC_MUX_SVC_EXP_RST_INT_N",
+ "FM_CPU_ERR2_LVT3_N", "BMC_MUX_CPU0_RST_INT_N", "BMC_MUX_M2_RST_INT_N",
+ /* S0 - S7 */
+ "SMB_SVC_PEX_RSSD01_16_INT", "RST_PCH_RSMRST_R_N", "", "", "BMC_ROT_FPGA_RESET_N",
+ "FM_SSD_CLK_DRVR0_EN", "", "",
+ /* T0 - T7 */
+ "", "", "", "", "", "", "", "",
+ /* U0 - U7 */
+ "", "", "", "", "", "", "", "",
+ /* V0 - V7 */
+ "BMC_PEX_IRQ_INT", "RTC_BATT_TEST", "SMB_PEX_VR_CTRL_INT", "SMB_SVC_PEX_CPU3_LED_INT",
+ "PWRGD_CPUPWRGD", "SMB_SVC_PEX_CPU2_LED_INT", "SMB_SVC_PEX_CPU1_LED_INT",
+ "BMC_MAC0_RESET_N",
+ /* W0 - W7 */
+ "", "", "", "", "", "", "", "",
+ /* X0 - X7 */
+ "", "", "", "", "", "", "", "",
+ /* Y0 - Y7 */
+ "FM_THROTTLE_N", "FM_PASSWORD_CLEAR_N", "H_LVT3_CATERR_DLY_N", "FM_CPU_OL_INT_R_N", "", "",
+ "", "",
+ /* Z0 - Z7 */
+ "FM_CPU_ERR0_LVT3_N", "FM_CPU_ERR1_LVT3_N", "BMC_MUX_VR_PCH_CPU_RST_INT_N",
+ "JTAG_MUX_LSP_SEL1", "", "JTAG_MUX_LSP_SEL4", "JTAG_MUX_LSP_SEL2", "";
+
+ gpio-reserved-ranges = <0 10>, <16 27>, <45 3>, <55 1>, <59 5>, <69 1>, <72 20>, <94 2>,
+ <102 2>, <105 1>, <117 1>, <128 1>, <146 2>, <150 18>, <176 16>, <196 4>, <204 1>, <207 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio0_unbiased_default>;
+};
+
+&pinctrl {
+ pinctrl_gpio0_unbiased_default: gpio_default {
+ pins = "AB15", "AD14", "R23", "A18", "AD24", "AD15", "AE14", "AC15", "U25", "AA24",
+ "V24", "W26", "AA23", "V26", "U24", "V25", "AE15", "C15", "F15";
+ bias-disable;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ bmc_mux_nic: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 3) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_nic: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 3) GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <19 1>, <22 6>, <30 6>, <38 2>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "IRQ_NIC2_OVT_WRNG", "FM_NIC2_ALLSTANDBY_N", "IRQ_NIC2_OVT_SHTDN",
+ "SMB_VR_PVCORE_NIC2_ALERT_N", "FM_NIC2_PERST1_N",
+ "SMB_NIC2_ALERT_N", "FM_NIC2_PERST3_N", "FM_NIC2_PERST2_N",
+ /* GPORT1 */
+ "FM_NIC1_RST_N", "FM_NIC1_PERST0_N", "FM_NIC1_PERST2_N",
+ "FM_NIC1_PERST3_N", "SMB_NIC1_ALERT_N", "FM_NIC1_PERST1_N",
+ "SMB_VR_PVCORE_NIC1_ALERT_N", "IRQ_NIC1_OVT_SHTDN",
+ /* GPORT2 */
+ "SMB_VR_P3V3_NIC_ALERT_N", "FM_NIC2_FLASH_PRSNT",
+ "FM_NIC1_FLASH_PRSNT", "",
+ /* GPORT3 */
+ "FM_NIC2_PERST0_N", "FM_NIC2_RST_N", "", "", "", "", "", "",
+ /* GPORT4 */
+ "FM_NIC1_ALLSTANDBY_N", "IRQ_NIC1_OVT_WRNG", "", "", "", "", "", "",
+ /* GPORT5 */
+ "SMB_VR_P1V8_NIC_ALERT_N", "SMB_VR_P1V2_NIC_ALERT_N", "", "";
+
+ pinctrl-0 = <&U62160_pins>;
+ pinctrl-names = "default";
+ U62160_pins: cfg-pins {
+ pins = "gp03", "gp16", "gp20", "gp50", "gp51";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ir38263-pvcore-nic2@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+
+ regulators {
+ pvcore_nic2: vout {
+ regulator-name = "pvcore_nic2";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ir38263-pvcore-nic1@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+
+ regulators {
+ pvcore_nic1: vout {
+ regulator-name = "pvcore_nic1";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ir38263-p3v3-nic@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+
+ regulators {
+ p3v3_nic: vout {
+ regulator-name = "p3v3_nic";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ir38263-p1v2-nic@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+
+ regulators {
+ p1v2_nic: vout {
+ regulator-name = "p1v2_nic";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ir38263-p1v8-nic@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+
+ regulators {
+ p1v8_nic: vout {
+ regulator-name = "p1v8_nic";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+
+ i2cmux1: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 7) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_m2_ssb_ssd1: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p3v3_aux>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "m2_ssb_ssd1:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_smb_m2_ssb_ssd1: sw0 {
+ shunt-resistor-micro-ohms = <12000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <2800000>;
+ regulator-name = "p3v3_m2_ssd1";
+ regulator-enable-ramp-delay = <10000>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_m2_ssb_ssd2: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <39 IRQ_TYPE_LEVEL_LOW>;
+ vss1-supply = <&p3v3_aux>;
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "m2_ssb_ssd2:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_smb_m2_ssb_ssd2: sw0 {
+ shunt-resistor-micro-ohms = <12000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <2800000>;
+ regulator-name = "p3v3_m2_ssd2";
+ regulator-enable-ramp-delay = <10000>;
+ };
+ };
+ };
+ };
+
+ i2c@6 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@7 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c4 {
+ status = "okay";
+ multi-master;
+ bus-frequency = <1000000>;
+
+ bmc-slave@10 {
+ compatible = "ipmb-dev";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+
+ i2c-protocol;
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ i2cmux2: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(Z, 2) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ r38263-p1v05-pch-aux@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ p1v05_pch_aux: vout {
+ regulator-name = "p1v05_pch_aux";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ir38060-p1v8-pch-aux@40 {
+ compatible = "infineon,ir38060";
+ reg = <0x40>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <32 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ p1v8_pch_aux: vout {
+ regulator-name = "p1v8_pch_aux";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c14 {
+ status = "okay";
+
+ i2cmux13: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 6) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_cpu0_event: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&smb_svc_pex_cpu0_led 16 GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "PWRGD_CHD_CPU0", "PWRGD_CHC_CPU0",
+ "PWRGD_CHB_CPU0", "PWRGD_CHA_CPU0",
+ "PWRGD_CHE_CPU0", "PWRGD_CHF_CPU0",
+ "PWRGD_CHG_CPU0", "PWRGD_CHH_CPU0",
+ /* GPORT1 */
+ "SMB_VR_PVPP_HBM_CPU0_ALERT_N", "SMB_VR_PVCCINFAON_CPU0_ALERT_N",
+ "SMB_VR_PVNN_MAIN_CPU0_ALERT_N", "SMB_VR_PVCCD_HV_CPU0_ALERT_N",
+ "SMB_VR_PVCCIN_CPU0_ALERT_N", "SEL_SMB_DIMM_CPU0",
+ "", "",
+ /* GPORT2 */
+ "PWRGD_LVC3_CPU0_AB_DRAM_G", "PWRGD_LVC3_CPU0_CD_DRAM_G",
+ "PWRGD_LVC3_CPU0_EF_DRAM_G", "PWRGD_LVC3_CPU0_GH_DRAM_G",
+ /* GPORT3 */
+ "FM_CPU0_DISABLE_COD_N", "",
+ "RST_LVC3_CPU0_RESET_N", "PWRGD_LVC3_CPU0_PWRGOOD",
+ "PWRGD_PLT_AUX_CPU0_LVT3", "",
+ "", "",
+ /* GPORT4 */
+ "H_LVT3_CPU0_PROCHOT_N", "H_LVT3_CPU0_MEMHOT_IN_N",
+ "H_LVT3_CPU0_MEMHOT_OUT_N", "H_LVT3_CPU0_MEMTRIP_OUT_N",
+ "H_LVT3_CPU0_THERMTRIP_OUT_N", "",
+ "H_LVT3_CPU0_NMI", "FM_S3M_CPU0_CD_INIT_ERROR",
+ /* GPORT5 */
+ "FM_CPU0_PKG_ID0", "FM_CPU0_PKG_ID1",
+ "FM_CPU0_PROC_ID0", "FM_CPU0_PROC_ID1";
+
+ pinctrl-0 = <&U62080_pins>;
+ pinctrl-names = "default";
+ U62080_pins: cfg-pins {
+ pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pvccinfaon-pvccfa-cpu0@58 {
+ compatible = "mps,mp2971";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu0_event>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccinfaon_cpu0: vout0 {
+ regulator-name = "pvccinfaon_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_cpu0: vout1 {
+ regulator-name = "pvccfa_ehv_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ tda38640-pvnn-main-cpu0@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu0_event>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvnn_main_cpu0: vout {
+ regulator-name = "pvnn_main_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mp2973-pvccin-pvccfa-cpu0@58 {
+ compatible = "mps,mp2973";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu0_event>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccin_cpu0: vout0 {
+ regulator-name = "pvccin_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_fivra_cpu0: vout1 {
+ regulator-name = "pvccfa_ehv_fivra_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvccd-hv-cpu0@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu0_event>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ infineon,en-pin-fixed-level;
+
+ regulators {
+ pvccd_hv_cpu0: vout {
+ regulator-name = "pvccd_hv_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvpp-hbm-cpu0@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu0_event>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvpp_hbm_cpu0: vout {
+ regulator-name = "pvpp_hbm_cpu0";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ i2cmux4: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(F, 3) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_cpu1_event: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&smb_svc_pex_cpu1_led 16 GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "PWRGD_CHD_CPU1", "PWRGD_CHC_CPU1",
+ "PWRGD_CHB_CPU1", "PWRGD_CHA_CPU1",
+ "PWRGD_CHE_CPU1", "PWRGD_CHF_CPU1",
+ "PWRGD_CHG_CPU1", "PWRGD_CHH_CPU1",
+ /* GPORT1 */
+ "SMB_VR_PVPP_HBM_CPU1_ALERT_N", "SMB_VR_PVCCINFAON_CPU1_ALERT_N",
+ "SMB_VR_PVNN_MAIN_CPU1_ALERT_N", "SMB_VR_PVCCD_HV_CPU1_ALERT_N",
+ "SMB_VR_PVCCIN_CPU1_ALERT_N", "SEL_SMB_DIMM_CPU1",
+ "", "",
+ /* GPORT2 */
+ "PWRGD_LVC3_CPU1_AB_DRAM_G", "PWRGD_LVC3_CPU1_CD_DRAM_G",
+ "PWRGD_LVC3_CPU1_EF_DRAM_G", "PWRGD_LVC3_CPU1_GH_DRAM_G",
+ /* GPORT3 */
+ "FM_CPU1_DISABLE_COD_N", "",
+ "RST_LVC3_CPU1_RESET_N", "PWRGD_LVC3_CPU1_PWRGOOD",
+ "PWRGD_PLT_AUX_CPU1_LVT3", "",
+ "", "",
+ /* GPORT4 */
+ "H_LVT3_CPU1_PROCHOT_N", "H_LVT3_CPU1_MEMHOT_IN_N",
+ "H_LVT3_CPU1_MEMHOT_OUT_N", "H_LVT3_CPU1_MEMTRIP_OUT_N",
+ "H_LVT3_CPU1_THERMTRIP_OUT_N", "",
+ "H_LVT3_CPU1_NMI", "FM_S3M_CPU1_CD_INIT_ERROR",
+ /* GPORT5 */
+ "FM_CPU1_PKG_ID0", "FM_CPU1_PKG_ID1",
+ "FM_CPU1_PROC_ID0", "FM_CPU1_PROC_ID1";
+
+ pinctrl-0 = <&U62090_pins>;
+ pinctrl-names = "default";
+ U62090_pins: cfg-pins {
+ pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pvccinfaon-pvccfa-cpu1@58 {
+ compatible = "mps,mp2971";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu1_event>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccinfaon_cpu1: vout0 {
+ regulator-name = "pvccinfaon_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_cpu1: vout1 {
+ regulator-name = "pvccfa_ehv_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ tda38640-pvnn-main-cpu1@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu1_event>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvnn_main_cpu1: vout {
+ regulator-name = "pvnn_main_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mp2973-pvccin-pvccfa-cpu1@58 {
+ compatible = "mps,mp2973";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu1_event>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccin_cpu1: vout0 {
+ regulator-name = "pvccin_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_fivra_cpu1: vout1 {
+ regulator-name = "pvccfa_ehv_fivra_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvccd-hv-cpu1@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu1_event>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ infineon,en-pin-fixed-level;
+
+ regulators {
+ pvccd_hv_cpu1: vout {
+ regulator-name = "pvccd_hv_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvpp-hbm-cpu1@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu1_event>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvpp_hbm_cpu1: vout {
+ regulator-name = "pvpp_hbm_cpu1";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+
+ i2cmux3: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(F, 4) IRQ_TYPE_LEVEL_HIGH>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_cpu2_event: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&smb_svc_pex_cpu2_led 16 GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "PWRGD_CHD_CPU2", "PWRGD_CHC_CPU2",
+ "PWRGD_CHB_CPU2", "PWRGD_CHA_CPU2",
+ "PWRGD_CHE_CPU2", "PWRGD_CHF_CPU2",
+ "PWRGD_CHG_CPU2", "PWRGD_CHH_CPU2",
+ /* GPORT1 */
+ "SMB_VR_PVPP_HBM_CPU2_ALERT_N", "SMB_VR_PVCCINFAON_CPU2_ALERT_N",
+ "SMB_VR_PVNN_MAIN_CPU2_ALERT_N", "SMB_VR_PVCCD_HV_CPU2_ALERT_N",
+ "SMB_VR_PVCCIN_CPU2_ALERT_N", "SEL_SMB_DIMM_CPU2",
+ "", "",
+ /* GPORT2 */
+ "PWRGD_LVC3_CPU2_AB_DRAM_G", "PWRGD_LVC3_CPU2_CD_DRAM_G",
+ "PWRGD_LVC3_CPU2_EF_DRAM_G", "PWRGD_LVC3_CPU2_GH_DRAM_G",
+ /* GPORT3 */
+ "FM_CPU2_DISABLE_COD_N", "",
+ "RST_LVC3_CPU2_RESET_N", "PWRGD_LVC3_CPU2_PWRGOOD",
+ "PWRGD_PLT_AUX_CPU2_LVT3", "",
+ "", "",
+ /* GPORT4 */
+ "H_LVT3_CPU2_PROCHOT_N", "H_LVT3_CPU2_MEMHOT_IN_N",
+ "H_LVT3_CPU2_MEMHOT_OUT_N", "H_LVT3_CPU2_MEMTRIP_OUT_N",
+ "H_LVT3_CPU2_THERMTRIP_OUT_N", "",
+ "H_LVT3_CPU2_NMI", "FM_S3M_CPU2_CD_INIT_ERROR",
+ /* GPORT5 */
+ "FM_CPU2_PKG_ID0", "FM_CPU2_PKG_ID1",
+ "FM_CPU2_PROC_ID0", "FM_CPU2_PROC_ID1";
+
+ pinctrl-0 = <&U62100_pins>;
+ pinctrl-names = "default";
+ U62100_pins: cfg-pins {
+ pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pvccinfaon-pvccfa-cpu2@58 {
+ compatible = "mps,mp2971";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu2_event>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccinfaon_cpu2: vout0 {
+ regulator-name = "pvccinfaon_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_cpu2: vout1 {
+ regulator-name = "pvccfa_ehv_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ tda38640-pvnn-main-cpu2@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu2_event>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvnn_main_cpu2: vout {
+ regulator-name = "pvnn_main_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mp2973-pvccin-pvccfa-cpu2@58 {
+ compatible = "mps,mp2973";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu2_event>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccin_cpu2: vout0 {
+ regulator-name = "pvccin_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_fivra_cpu2: vout1 {
+ regulator-name = "pvccfa_ehv_fivra_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvccd-hv-cpu2@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu2_event>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ infineon,en-pin-fixed-level;
+
+ regulators {
+ pvccd_hv_cpu2: vout {
+ regulator-name = "pvccd_hv_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvpp-hbm-cpu2@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu2_event>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvpp_hbm_cpu2: vout {
+ regulator-name = "pvpp_hbm_cpu2";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c12 {
+ status = "okay";
+
+ i2cmux22: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(P, 2) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_cpu3_event: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&smb_svc_pex_cpu3_led 16 GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "PWRGD_CHD_CPU3", "PWRGD_CHC_CPU3",
+ "PWRGD_CHB_CPU3", "PWRGD_CHA_CPU3",
+ "PWRGD_CHE_CPU3", "PWRGD_CHF_CPU3",
+ "PWRGD_CHG_CPU3", "PWRGD_CHH_CPU3",
+ /* GPORT1 */
+ "SMB_VR_PVPP_HBM_CPU3_ALERT_N", "SMB_VR_PVCCINFAON_CPU3_ALERT_N",
+ "SMB_VR_PVNN_MAIN_CPU3_ALERT_N", "SMB_VR_PVCCD_HV_CPU3_ALERT_N",
+ "SMB_VR_PVCCIN_CPU3_ALERT_N", "SEL_SMB_DIMM_CPU3",
+ "", "",
+ /* GPORT2 */
+ "PWRGD_LVC3_CPU3_AB_DRAM_G", "PWRGD_LVC3_CPU3_CD_DRAM_G",
+ "PWRGD_LVC3_CPU3_EF_DRAM_G", "PWRGD_LVC3_CPU3_GH_DRAM_G",
+ /* GPORT3 */
+ "FM_CPU3_DISABLE_COD_N", "",
+ "RST_LVC3_CPU3_RESET_N", "PWRGD_LVC3_CPU3_PWRGOOD",
+ "PWRGD_PLT_AUX_CPU3_LVT3", "",
+ "", "",
+ /* GPORT4 */
+ "H_LVT3_CPU3_PROCHOT_N", "H_LVT3_CPU3_MEMHOT_IN_N",
+ "H_LVT3_CPU3_MEMHOT_OUT_N", "H_LVT3_CPU3_MEMTRIP_OUT_N",
+ "H_LVT3_CPU3_THERMTRIP_OUT_N", "",
+ "H_LVT3_CPU3_NMI", "FM_S3M_CPU3_CD_INIT_ERROR",
+ /* GPORT5 */
+ "FM_CPU3_PKG_ID0", "FM_CPU3_PKG_ID1",
+ "FM_CPU3_PROC_ID0", "FM_CPU3_PROC_ID1";
+
+ pinctrl-0 = <&U62110_pins>;
+ pinctrl-names = "default";
+ U62110_pins: cfg-pins {
+ pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pvccinfaon-pvccfa-cpu3@58 {
+ compatible = "mps,mp2971";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu3_event>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccinfaon_cpu3: vout0 {
+ regulator-name = "pvccinfaon_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_cpu3: vout1 {
+ regulator-name = "pvccfa_ehv_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ tda38640-pvnn-main-cpu3@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu3_event>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvnn_main_cpu3: vout {
+ regulator-name = "pvnn_main_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mp2973-pvccin-pvccfa-cpu3@58 {
+ compatible = "mps,mp2973";
+ reg = <0x58>;
+ interrupt-parent = <&smb_pex_cpu3_event>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvccin_cpu3: vout0 {
+ regulator-name = "pvccin_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ pvccfa_ehv_fivra_cpu3: vout1 {
+ regulator-name = "pvccfa_ehv_fivra_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvccd-hv-cpu3@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu3_event>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ infineon,en-pin-fixed-level;
+
+ regulators {
+ pvccd_hv_cpu3: vout {
+ regulator-name = "pvccd_hv_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tda38640-pvpp-hbm-cpu3@40 {
+ compatible = "infineon,tda38640";
+ reg = <0x40>;
+ interrupt-parent = <&smb_pex_cpu3_event>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ pvpp_hbm_cpu3: vout {
+ regulator-name = "pvpp_hbm_cpu3";
+ regulator-enable-ramp-delay = <200>;
+ };
+ };
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c15 {
+ status = "okay";
+
+ i2cmux14: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux15: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 11 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux16: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 2 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux17: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 0 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux18: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 3 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux19: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 9 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_rssd17_32: pinctrl@20 {
+ compatible = "cypress,cy8c9560";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&bmc_pex_irq>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&bmc_pex_irq 19 GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <48 12>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "RSSD17_SMBRST_N", "RSSD18_SMBRST_N",
+ "RSSD19_SMBRST_N", "RSSD20_SMBRST_N",
+ "RSSD21_SMBRST_N", "RSSD22_SMBRST_N",
+ "RSSD23_SMBRST_N", "RSSD24_SMBRST_N",
+ /* GPORT1 */
+ "RSSD25_SMBRST_N", "RSSD26_SMBRST_N",
+ "RSSD27_SMBRST_N", "RSSD28_SMBRST_N",
+ "RSSD29_SMBRST_N", "RSSD30_SMBRST_N",
+ "RSSD31_SMBRST_N", "RSSD32_SMBRST_N",
+ /* GPORT2 */
+ "RSSD17_PWRDIS", "RSSD18_PWRDIS",
+ "RSSD19_PWRDIS", "RSSD20_PWRDIS",
+ /* GPORT3 */
+ "RSSD21_PWRDIS", "RSSD22_PWRDIS",
+ "RSSD23_PWRDIS", "RSSD24_PWRDIS",
+ "RSSD25_PWRDIS", "RSSD26_PWRDIS",
+ "RSSD27_PWRDIS", "RSSD28_PWRDIS",
+ /* GPORT4 */
+ "RSSD29_PWRDIS", "RSSD30_PWRDIS",
+ "RSSD31_PWRDIS", "RSSD32_PWRDIS",
+ "RSSD17_RESET_N", "RSSD18_RESET_N",
+ "RSSD19_RESET_N", "RSSD20_RESET_N",
+ /* GPORT5 */
+ "RSSD21_RESET_N", "RSSD22_RESET_N",
+ "RSSD23_RESET_N", "RSSD24_RESET_N",
+ "RSSD25_RESET_N", "RSSD26_RESET_N",
+ "RSSD27_RESET_N", "RSSD28_RESET_N",
+ /* GPORT6 */
+ "RSSD29_RESET_N", "RSSD30_RESET_N",
+ "RSSD31_RESET_N", "RSSD32_RESET_N",
+ "", "",
+ "", "",
+ /* GPORT7 */
+ "", "",
+ "", "",
+ "", "",
+ "", "";
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux20: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 4 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux21: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 5 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ i2cmux5: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 0) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux6: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 16 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux7: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux8: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 1 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux9: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 10 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux10: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_pex_rssd_01_16: pinctrl@20 {
+ compatible = "cypress,cy8c9560";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&bmc_pex_irq>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&bmc_pex_irq 18 GPIO_ACTIVE_HIGH>;
+
+ gpio-reserved-ranges = <48 12>;
+
+ gpio-line-names =
+ /* GPORT0 */
+ "RSSD01_SMBRST_N", "RSSD02_SMBRST_N",
+ "RSSD03_SMBRST_N", "RSSD04_SMBRST_N",
+ "RSSD05_SMBRST_N", "RSSD06_SMBRST_N",
+ "RSSD07_SMBRST_N", "RSSD08_SMBRST_N",
+ /* GPORT1 */
+ "RSSD09_SMBRST_N", "RSSD10_SMBRST_N",
+ "RSSD11_SMBRST_N", "RSSD12_SMBRST_N",
+ "RSSD13_SMBRST_N", "RSSD14_SMBRST_N",
+ "RSSD15_SMBRST_N", "RSSD16_SMBRST_N",
+ /* GPORT2 */
+ "RSSD01_PWRDIS", "RSSD02_PWRDIS",
+ "RSSD03_PWRDIS", "RSSD04_PWRDIS",
+ /* GPORT3 */
+ "RSSD05_PWRDIS", "RSSD06_PWRDIS",
+ "RSSD07_PWRDIS", "RSSD08_PWRDIS",
+ "RSSD09_PWRDIS", "RSSD10_PWRDIS",
+ "RSSD11_PWRDIS", "RSSD12_PWRDIS",
+ /* GPORT4 */
+ "RSSD13_PWRDIS", "RSSD14_PWRDIS",
+ "RSSD15_PWRDIS", "RSSD16_PWRDIS",
+ "RSSD01_RESET_N", "RSSD02_RESET_N",
+ "RSSD03_RESET_N", "RSSD04_RESET_N",
+ /* GPORT5 */
+ "RSSD05_RESET_N", "RSSD06_RESET_N",
+ "RSSD07_RESET_N", "RSSD08_RESET_N",
+ "RSSD09_RESET_N", "RSSD10_RESET_N",
+ "RSSD11_RESET_N", "RSSD12_RESET_N",
+ /* GPORT6 */
+ "RSSD13_RESET_N", "RSSD14_RESET_N",
+ "RSSD15_RESET_N", "RSSD16_RESET_N",
+ "", "",
+ "", "",
+ /* GPORT7 */
+ "", "",
+ "", "",
+ "", "",
+ "", "";
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux11: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 12 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2cmux12: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&bmc_pex_irq 14 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_aux>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+ };
+};
+
+&i2c13 {
+ status = "okay";
+
+ i2cmux23: mux@77 {
+ compatible = "maxim,max7357";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 4) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ };
+};
+
+&i2cmux23 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ smb_pex_vr_ctrl: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(V, 2) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 2) GPIO_ACTIVE_HIGH>;
+ gpio-line-names =
+ /* GPORT0 */
+ "BCM0_INPUT_DISABLE_N", "SMB_VR_P3V3_AUX_ALERT_N",
+ "SMB_PEX_CPU1_EVENT_INT", "SMB_PEX_CPU2_EVENT_INT",
+ "DPIC0_VOLTAGE_DETECTB_N", "DPIC0_VOLTAGE_DETECTA_N",
+ "DPIC1_VOLTAGE_DETECTA_N", "DPIC1_VOLTAGE_DETECTB_N",
+ /* GPORT1 */
+ "SMB_PEX_NIC_INT", "SMB_VR_P1V05_PCH_AUX_ALERT_N",
+ "SMB_PEX_CPU0_EVENT_INT", "SMB_PEX_CPU3_EVENT_INT",
+ "LED_ID_TPM", "PLUG_DETECT_TPM",
+ "PLUG_DETECT_M2_SSD_CARRIER1", "RST_M2_SSD1_PERST_N",
+ /* GPORT2 */
+ "LED_ID_BAT", "LED_ID_MGMT_PORT2",
+ "LED_ID_MGMT_PORT1", "SMB_VR_P5V_AUX_ALERT_N",
+ /* GPORT3 */
+ "SMB_VR_AUX_SSB_ALERT_N", "BCM1_INPUT_DISABLE_N",
+ "LED_ID_NIC1_PORT1", "LED_ID_NIC1_PORT2",
+ "LED_ID_NIC2_PORT1", "LED_ID_NIC2_PORT2",
+ "RST_M2_SSD2_PERST_N", "PLUG_DETECT_M2_SSD2",
+ /* GPORT4 */
+ "PLUG_DETECT_BAT", "PLUG_DETECT_M2_SSD1",
+ "M2_SSD1_SSB_ALERT_N", "BCM2_INPUT_DISABLE_N",
+ "SMB_VR_P1V8_PCH_AUX_ALERT_N", "BCM3_INPUT_DISABLE_N",
+ "LED_PWR_DWR_BACK", "LED_ID_DWR_BACK_P",
+ /* GPORT5 */
+ "LED_ID_M2_SSD2", "LED_ID_M2_SSD1",
+ "PLUG_DETECT_M2_SSD_CARRIER2", "M2_SSD2_SSB_ALERT_N";
+
+ pinctrl-0 = <&U62120_input &U62120_input_pullup>;
+ pinctrl-names = "default";
+ U62120_input: input-pins {
+ pins = "gp10";
+ function = "gpio";
+ input-enable;
+ bias-disable;
+ };
+ U62120_input_pullup: input-pullup-pins {
+ pins = "gp01", "gp02", "gp03", "gp11", "gp12", "gp13",
+ "gp23", "gp30", "gp40", "gp42", "gp44", "gp53";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bmc_pex_irq: pinctrl@20 {
+ compatible = "cypress,cy8c9520";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(V, 0) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 1) GPIO_ACTIVE_HIGH>;
+ gpio-line-names =
+ /* GPORT0 */
+ "SMB_MUX_PWM_FANGRP2_RST_INT_N", "SMB_MUX_SSB_FANGRP2_RST_INT_N",
+ "SMB_MUX_PWM_FANGRP1_RST_INT_N", "SMB_MUX_SSB_RSSD01_08_RST_INT_N",
+ "SMB_MUX_RSSD01_08_RST_INT_N", "SMB_MUX_RSSD09_16_RST_INT_N",
+ "SMB_PEX_RSSD01_16_INT", "SMB_MUX_SSB_FANGRP1_RST_INT_N",
+ /* GPORT1 */
+ "SMB_SVC_PEX_FAN_ALERT_INT", "SMB_MUX_SSB_RSSD09_16_RST_INT_N",
+ "SMB_MUX_SSB_RSSD17_24_RST_INT_N", "SMB_MUX_PWM_FANGRP0_RST_INT_N",
+ "SMB_MUX_RSSD17_24_RST_INT_N", "SMB_PEX_RSSD17_32_INT",
+ "SMB_MUX_RSSD25_32_RST_INT_N", "SMB_MUX_SSB_RSSD25_32_RST_INT_N",
+ /* GPORT2 */
+ "SMB_MUX_SSB_FANGRP0_RST_INT_N", "PEX_FAN_ALERT_RST",
+ "PEX_RSSD01_16_RST", "PEX_RSSD17_32_RST";
+ pinctrl-0 = <&U60000_pins>;
+ pinctrl-names = "default";
+ U60000_pins: cfg-pins {
+ pins = "gp06", "gp10", "gp15";
+ function = "gpio";
+ input-enable;
+ bias-disable;
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2cmux24: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&p3v3_bmc_aux>;
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ vcc-supply = <&p3v3_bmc_aux>;
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2cmux25: mux@70 {
+ compatible = "maxim,max7357";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2cmux25 {
+ reset-gpios = <&gpio0 ASPEED_GPIO(R, 2) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ir38263-p5v-aux@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+ regulators {
+ p5v_aux: vout {
+ regulator-name = "p5v_aux";
+ regulator-enable-ramp-delay = <2000>;
+ vin-supply = <&p12v>;
+ vbus-supply = <&p3v3_bmc_aux>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ir38263-p3v3-aux@40 {
+ compatible = "infineon,ir38263";
+ reg = <0x40>;
+ regulators {
+ p3v3_aux: vout {
+ vin-supply = <&p12v>;
+ regulator-name = "p3v3_aux";
+ /*
+ * 2msec for regulator + 18msec for board capacitance
+ * Note: Every IC has a PTC which slowly charges the bypass
+ * cap.
+ */
+ regulator-enable-ramp-delay = <200000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ aux_ssb: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_pex_vr_ctrl>;
+ interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+ vss1-supply = <&p5v_aux>;
+ vss2-supply = <&p3v3_aux>;
+ regulators {
+ p5v: sw0 {
+ regulator-name = "p5v";
+ shunt-resistor-micro-ohms = <12000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <100000>;
+ };
+ p3v3_pch: sw1 {
+ regulator-name = "p3v3_pch";
+ shunt-resistor-micro-ohms = <12000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <100000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pli1209bc_p12v_a: regulator@5f {
+ compatible = "vicor,pli1209bc";
+ reg = <0x5f>;
+ regulators {
+ p12v_a: vout2 {
+ regulator-name = "bcm0";
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pli1209bc_p12v_b: regulator@5f {
+ compatible = "vicor,pli1209bc";
+ reg = <0x5f>;
+ regulators {
+ p12v_b: vout2 {
+ regulator-name = "bcm1";
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pli1209bc_p12v_c: regulator@5f {
+ compatible = "vicor,pli1209bc";
+ reg = <0x5f>;
+ regulators {
+ p12v_c: vout2 {
+ regulator-name = "bcm2";
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pli1209bc_p12v_d: regulator@5f {
+ compatible = "vicor,pli1209bc";
+ reg = <0x5f>;
+ regulators {
+ p12v_d: vout2 {
+ regulator-name = "bcm3";
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+};
+
+&i2cmux24 {
+
+ reset-gpios = <&gpio0 ASPEED_GPIO(P, 3) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ smb_svc_pex_rssd01_16: pinctrl@20 {
+ compatible = "cypress,cy8c9560";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&smb_svc_pex_cpu0_led 17 GPIO_ACTIVE_HIGH>;
+ gpio-line-names =
+ /* GPORT0 */
+ "LED_ID_RSSD01", "LED_ID_RSSD02",
+ "LED_ID_RSSD03", "LED_ID_RSSD04",
+ "LED_ID_RSSD05", "LED_ID_RSSD06",
+ "LED_ID_RSSD07", "LED_ID_RSSD08",
+ /* GPORT1 */
+ "LED_ID_RSSD09", "LED_ID_RSSD10",
+ "LED_ID_RSSD11", "LED_ID_RSSD12",
+ "LED_ID_RSSD13", "LED_ID_RSSD14",
+ "LED_ID_RSSD15", "LED_ID_RSSD16",
+ /* GPORT2 */
+ "RSSD01_PRESENT_N", "RSSD02_PRESENT_N",
+ "RSSD03_PRESENT_N", "RSSD04_PRESENT_N",
+ /* GPORT3 */
+ "RSSD05_PRESENT_N", "RSSD06_PRESENT_N",
+ "RSSD07_PRESENT_N", "RSSD08_PRESENT_N",
+ "RSSD09_PRESENT_N", "RSSD10_PRESENT_N",
+ "RSSD11_PRESENT_N", "RSSD12_PRESENT_N",
+ /* GPORT4 */
+ "RSSD13_PRESENT_N", "RSSD14_PRESENT_N",
+ "RSSD15_PRESENT_N", "RSSD16_PRESENT_N",
+ "LED_ID_FAN_ASM01", "LED_ID_FAN_ASM02",
+ "LED_ID_FAN_ASM03", "LED_ID_FAN_ASM04",
+ /* GPORT5 */
+ "LED_ID_FAN_ASM05", "LED_ID_FAN_ASM06",
+ "PLUG_DETECT_FAN_ASM01", "PLUG_DETECT_FAN_ASM02",
+ "PLUG_DETECT_FAN_ASM03", "PLUG_DETECT_FAN_ASM04",
+ "PLUG_DETECT_FAN_ASM05", "PLUG_DETECT_FAN_ASM06",
+ /* GPORT6 */
+ "SSB_RSSD01_ALERT_N", "SSB_RSSD02_ALERT_N",
+ "SSB_RSSD03_ALERT_N", "SSB_RSSD04_ALERT_N",
+ "SSB_RSSD05_ALERT_N", "SSB_RSSD06_ALERT_N",
+ "SSB_RSSD07_ALERT_N", "SSB_RSSD08_ALERT_N",
+ /* GPORT7 */
+ "SSB_RSSD09_ALERT_N", "SSB_RSSD10_ALERT_N",
+ "SSB_RSSD11_ALERT_N", "SSB_RSSD12_ALERT_N",
+ "SSB_RSSD13_ALERT_N", "SSB_RSSD14_ALERT_N",
+ "SSB_RSSD15_ALERT_N", "SSB_RSSD16_ALERT_N";
+ pinctrl-0 = <&U65200_pins>;
+ pinctrl-names = "default";
+ U65200_pins: cfg-pins {
+ pins = "gp60", "gp61", "gp62",
+ "gp63", "gp64", "gp65", "gp66",
+ "gp67", "gp70", "gp71", "gp72",
+ "gp73", "gp74", "gp75", "gp76", "gp77";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ smb_svc_pex_rssd17_32: pinctrl@20 {
+ compatible = "cypress,cy8c9560";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(H, 0) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&smb_svc_pex_cpu1_led 17 GPIO_ACTIVE_HIGH>;
+ gpio-line-names =
+ /* GPORT0 */
+ "LED_ID_RSSD17", "LED_ID_RSSD18",
+ "LED_ID_RSSD19", "LED_ID_RSSD20",
+ "LED_ID_RSSD21", "LED_ID_RSSD22",
+ "LED_ID_RSSD23", "LED_ID_RSSD24",
+ /* GPORT1 */
+ "LED_ID_RSSD25", "LED_ID_RSSD26",
+ "LED_ID_RSSD27", "LED_ID_RSSD28",
+ "LED_ID_RSSD29", "LED_ID_RSSD30",
+ "LED_ID_RSSD31", "LED_ID_RSSD32",
+ /* GPORT2 */
+ "RSSD17_PRESENT_N", "RSSD18_PRESENT_N",
+ "RSSD19_PRESENT_N", "RSSD20_PRESENT_N",
+ /* GPORT3 */
+ "RSSD21_PRESENT_N", "RSSD22_PRESENT_N",
+ "RSSD23_PRESENT_N", "RSSD24_PRESENT_N",
+ "RSSD25_PRESENT_N", "RSSD26_PRESENT_N",
+ "RSSD27_PRESENT_N", "RSSD28_PRESENT_N",
+ /* GPORT4 */
+ "RSSD29_PRESENT_N", "RSSD30_PRESENT_N",
+ "RSSD31_PRESENT_N", "RSSD32_PRESENT_N",
+ "LED_ID_FAN_ASM07", "LED_ID_FAN_ASM08",
+ "LED_ID_FAN_ASM09", "LED_ID_FAN_ASM10",
+ /* GPORT5 */
+ "LED_ID_FAN_ASM11", "LED_ID_FAN_ASM12",
+ "PLUG_DETECT_FAN_ASM07", "PLUG_DETECT_FAN_ASM08",
+ "PLUG_DETECT_FAN_ASM09", "PLUG_DETECT_FAN_ASM10",
+ "PLUG_DETECT_FAN_ASM11", "PLUG_DETECT_FAN_ASM12",
+ /* GPORT6 */
+ "SSB_RSSD17_ALERT_N", "SSB_RSSD18_ALERT_N",
+ "SSB_RSSD19_ALERT_N", "SSB_RSSD20_ALERT_N",
+ "SSB_RSSD21_ALERT_N", "SSB_RSSD22_ALERT_N",
+ "SSB_RSSD23_ALERT_N", "SSB_RSSD24_ALERT_N",
+ /* GPORT7 */
+ "SSB_RSSD25_ALERT_N", "SSB_RSSD26_ALERT_N",
+ "SSB_RSSD27_ALERT_N", "SSB_RSSD28_ALERT_N",
+ "SSB_RSSD29_ALERT_N", "SSB_RSSD30_ALERT_N",
+ "SSB_RSSD31_ALERT_N", "SSB_RSSD32_ALERT_N";
+ pinctrl-0 = <&U65300_pins>;
+ pinctrl-names = "default";
+ U65300_pins: cfg-pins {
+ pins = "gp60", "gp61", "gp62",
+ "gp63", "gp64", "gp65", "gp66",
+ "gp67", "gp70", "gp71", "gp72",
+ "gp73", "gp74", "gp75", "gp76",
+ "gp77";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ smb_svc_pex_cpu1_led: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(V, 6) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 5) GPIO_ACTIVE_HIGH>;
+ gpio-reserved-ranges = <18 2>, <36 2>;
+ gpio-line-names =
+ /* GPORT0 */
+ "PLUG_DETECT_DIMM_C1E2", "PLUG_DETECT_DIMM_C1E1",
+ "PLUG_DETECT_DIMM_C1F2", "PLUG_DETECT_DIMM_C1F1",
+ "PLUG_DETECT_DIMM_C1G2", "PLUG_DETECT_DIMM_C1G1",
+ "PLUG_DETECT_DIMM_C1H2", "PLUG_DETECT_DIMM_C1H1",
+ /* GPORT1 */
+ "PLUG_DETECT_DIMM_C1D1", "PLUG_DETECT_DIMM_C1D2",
+ "PLUG_DETECT_DIMM_C1C1", "PLUG_DETECT_DIMM_C1C2",
+ "PLUG_DETECT_DIMM_C1B1", "PLUG_DETECT_DIMM_C1B2",
+ "PLUG_DETECT_DIMM_C1A1", "PLUG_DETECT_DIMM_C1A2",
+ /* GPORT2 */
+ "PEX_CPU1_EVENT_RST", "SVC_PEX_RSSD17_32_RST",
+ "", "",
+ /* GPORT3 */
+ "LED_ID_DIMM_C1E2", "LED_ID_DIMM_C1E1",
+ "LED_ID_DIMM_C1F2", "LED_ID_DIMM_C1F1",
+ "LED_ID_DIMM_C1G2", "LED_ID_DIMM_C1G1",
+ "LED_ID_DIMM_C1H2", "LED_ID_DIMM_C1H1",
+ /* GPORT4 */
+ "LED_ID_DIMM_C1A2", "LED_ID_DIMM_C1A1",
+ "LED_ID_DIMM_C1B2", "LED_ID_DIMM_C1B1",
+ "LED_ID_DIMM_C1C2", "LED_ID_DIMM_C1C1",
+ "LED_ID_DIMM_C1D2", "LED_ID_DIMM_C1D1",
+ /* GPORT5 */
+ "", "",
+ "FM_CPU1_SKTOCC_N", "LED_ID_CPU1";
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ smb_svc_pex_fan_alert: pinctrl@20 {
+ compatible = "cypress,cy8c9560";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&bmc_pex_irq>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_aux>;
+ reset-gpios = <&bmc_pex_irq 17 GPIO_ACTIVE_HIGH>;
+ gpio-reserved-ranges = <24 3>, <51 9>;
+ gpio-line-names =
+ /* GPORT0 */
+ "FAN01_SSB_ALERT_N", "FAN02_SSB_ALERT_N",
+ "FAN03_SSB_ALERT_N", "FAN04_SSB_ALERT_N",
+ "FAN05_SSB_ALERT_N", "FAN06_SSB_ALERT_N",
+ "FAN07_SSB_ALERT_N", "FAN08_SSB_ALERT_N",
+ /* GPORT1 */
+ "FAN09_SSB_ALERT_N", "FAN10_SSB_ALERT_N",
+ "FAN11_SSB_ALERT_N", "FAN12_SSB_ALERT_N",
+ "FAN13_SSB_ALERT_N", "FAN14_SSB_ALERT_N",
+ "FAN15_SSB_ALERT_N", "FAN16_SSB_ALERT_N",
+ /* GPORT2 */
+ "FAN17_SSB_ALERT_N", "FAN18_SSB_ALERT_N",
+ "FAN19_SSB_ALERT_N", "FAN20_SSB_ALERT_N",
+ /* GPORT3 */
+ "FAN21_SSB_ALERT_N", "FAN22_SSB_ALERT_N",
+ "FAN23_SSB_ALERT_N", "FAN24_SSB_ALERT_N",
+ "", "",
+ "", "FAN01_PWM_ALERT_N",
+ /* GPORT4 */
+ "FAN02_PWM_ALERT_N", "FAN03_PWM_ALERT_N",
+ "FAN04_PWM_ALERT_N", "FAN05_PWM_ALERT_N",
+ "FAN06_PWM_ALERT_N", "FAN07_PWM_ALERT_N",
+ "FAN08_PWM_ALERT_N", "FAN09_PWM_ALERT_N",
+ /* GPORT5 */
+ "FAN10_PWM_ALERT_N", "FAN11_PWM_ALERT_N",
+ "FAN12_PWM_ALERT_N", "FAN13_PWM_ALERT_N",
+ "FAN14_PWM_ALERT_N", "FAN15_PWM_ALERT_N",
+ "FAN16_PWM_ALERT_N", "FAN17_PWM_ALERT_N",
+ /* GPORT6 */
+ "FAN18_PWM_ALERT_N", "FAN19_PWM_ALERT_N",
+ "FAN20_PWM_ALERT_N", "FAN21_PWM_ALERT_N",
+ "FAN22_PWM_ALERT_N", "FAN23_PWM_ALERT_N",
+ "FAN24_PWM_ALERT_N", "",
+ /* GPORT7 */
+ "", "",
+ "", "",
+ "", "",
+ "", "";
+ pinctrl-0 = <&U65600_pins>;
+ pinctrl-names = "default";
+ U65600_pins: cfg-pins {
+ pins = "gp00", "gp01", "gp02",
+ "gp03", "gp04", "gp05", "gp06",
+ "gp07", "gp10", "gp11", "gp12",
+ "gp13", "gp14", "gp15", "gp16",
+ "gp17", "gp20", "gp21", "gp22",
+ "gp23", "gp30", "gp31", "gp32",
+ "gp33", "gp37", "gp40", "gp41",
+ "gp42", "gp43", "gp44", "gp45",
+ "gp46", "gp47", "gp50", "gp51",
+ "gp52", "gp53", "gp54", "gp55",
+ "gp56", "gp57", "gp60", "gp61",
+ "gp62", "gp63", "gp64", "gp65",
+ "gp66";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ smb_svc_pex_cpu2_led: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(V, 5) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
+ gpio-reserved-ranges = <17 3>, <36 2>;
+ gpio-line-names =
+ /* GPORT0 */
+ "PLUG_DETECT_DIMM_C2E2", "PLUG_DETECT_DIMM_C2E1",
+ "PLUG_DETECT_DIMM_C2F2", "PLUG_DETECT_DIMM_C2F1",
+ "PLUG_DETECT_DIMM_C2G2", "PLUG_DETECT_DIMM_C2G1",
+ "PLUG_DETECT_DIMM_C2H2", "PLUG_DETECT_DIMM_C2H1",
+ /* GPORT1 */
+ "PLUG_DETECT_DIMM_C2D1", "PLUG_DETECT_DIMM_C2D2",
+ "PLUG_DETECT_DIMM_C2C1", "PLUG_DETECT_DIMM_C2C2",
+ "PLUG_DETECT_DIMM_C2B1", "PLUG_DETECT_DIMM_C2B2",
+ "PLUG_DETECT_DIMM_C2A1", "PLUG_DETECT_DIMM_C2A2",
+ /* GPORT2 */
+ "PEX_CPU2_EVENT_RST", "",
+ "", "",
+ /* GPORT3 */
+ "LED_ID_DIMM_C2E2", "LED_ID_DIMM_C2E1",
+ "LED_ID_DIMM_C2F2", "LED_ID_DIMM_C2F1",
+ "LED_ID_DIMM_C2G2", "LED_ID_DIMM_C2G1",
+ "LED_ID_DIMM_C2H2", "LED_ID_DIMM_C2H1",
+ /* GPORT4 */
+ "LED_ID_DIMM_C2A2", "LED_ID_DIMM_C2A1",
+ "LED_ID_DIMM_C2B2", "LED_ID_DIMM_C2B1",
+ "LED_ID_DIMM_C2C2", "LED_ID_DIMM_C2C1",
+ "LED_ID_DIMM_C2D2", "LED_ID_DIMM_C2D1",
+ /* GPORT5 */
+ "", "",
+ "FM_CPU2_SKTOCC_N", "LED_ID_CPU2";
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb_svc_pex_cpu3_led: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(V, 3) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+ gpio-reserved-ranges = <17 3>;
+ gpio-line-names =
+ /* GPORT0 */
+ "PLUG_DETECT_DIMM_C3E2", "PLUG_DETECT_DIMM_C3E1",
+ "PLUG_DETECT_DIMM_C3F2", "PLUG_DETECT_DIMM_C3F1",
+ "PLUG_DETECT_DIMM_C3G2", "PLUG_DETECT_DIMM_C3G1",
+ "PLUG_DETECT_DIMM_C3H2", "PLUG_DETECT_DIMM_C3H1",
+ /* GPORT1 */
+ "PLUG_DETECT_DIMM_C3D1", "PLUG_DETECT_DIMM_C3D2",
+ "PLUG_DETECT_DIMM_C3C1", "PLUG_DETECT_DIMM_C3C2",
+ "PLUG_DETECT_DIMM_C3B1", "PLUG_DETECT_DIMM_C3B2",
+ "PLUG_DETECT_DIMM_C3A1", "PLUG_DETECT_DIMM_C3A2",
+ /* GPORT2 */
+ "PEX_CPU3_EVENT_RST", "",
+ "", "",
+ /* GPORT3 */
+ "LED_ID_DIMM_C3E2", "LED_ID_DIMM_C3E1",
+ "LED_ID_DIMM_C3F2", "LED_ID_DIMM_C3F1",
+ "LED_ID_DIMM_C3G2", "LED_ID_DIMM_C3G1",
+ "LED_ID_DIMM_C3H2", "LED_ID_DIMM_C3H1",
+ /* GPORT4 */
+ "LED_ID_DIMM_C3A2", "LED_ID_DIMM_C3A1",
+ "LED_ID_DIMM_C3B2", "LED_ID_DIMM_C3B1",
+ "LED_ID_DIMM_C3C2", "LED_ID_DIMM_C3C1",
+ "LED_ID_DIMM_C3D2", "LED_ID_DIMM_C3D1",
+ /* GPORT5 */
+ "LED_PWR_DWR_FRNT", "LED_ID_DWR_FRNT_P",
+ "FM_CPU3_SKTOCC_N", "LED_ID_CPU3";
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ smb_svc_pex_cpu0_led: pinctrl@20 {
+ compatible = "cypress,cy8c9540";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(O, 3) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vdd-supply = <&p3v3_bmc_aux>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
+ gpio-reserved-ranges = <18 2>, <36 2>;
+ gpio-line-names =
+ /* GPORT0 */
+ "PLUG_DETECT_DIMM_C0E2", "PLUG_DETECT_DIMM_C0E1",
+ "PLUG_DETECT_DIMM_C0F2", "PLUG_DETECT_DIMM_C0F1",
+ "PLUG_DETECT_DIMM_C0G2", "PLUG_DETECT_DIMM_C0G1",
+ "PLUG_DETECT_DIMM_C0H2", "PLUG_DETECT_DIMM_C0H1",
+ /* GPORT1 */
+ "PLUG_DETECT_DIMM_C0D1", "PLUG_DETECT_DIMM_C0D2",
+ "PLUG_DETECT_DIMM_C0C1", "PLUG_DETECT_DIMM_C0C2",
+ "PLUG_DETECT_DIMM_C0B1", "PLUG_DETECT_DIMM_C0B2",
+ "PLUG_DETECT_DIMM_C0A1", "PLUG_DETECT_DIMM_C0A2",
+ /* GPORT2 */
+ "PEX_CPU0_EVENT_RST", "SVC_PEX_RSSD01_16_RST",
+ "", "",
+ /* GPORT3 */
+ "LED_ID_DIMM_C0E2", "LED_ID_DIMM_C0E1",
+ "LED_ID_DIMM_C0F2", "LED_ID_DIMM_C0F1",
+ "LED_ID_DIMM_C0G2", "LED_ID_DIMM_C0G1",
+ "LED_ID_DIMM_C0H2", "LED_ID_DIMM_C0H1",
+ /* GPORT4 */
+ "LED_ID_DIMM_C0A2", "LED_ID_DIMM_C0A1",
+ "LED_ID_DIMM_C0B2", "LED_ID_DIMM_C0B1",
+ "LED_ID_DIMM_C0C2", "LED_ID_DIMM_C0C1",
+ "LED_ID_DIMM_C0D2", "LED_ID_DIMM_C0D1",
+ /* GPORT5 */
+ "", "",
+ "FM_CPU0_SKTOCC_N", "LED_ID_CPU0";
+ };
+ };
+};
+
+&i2c9 {
+ status = "okay";
+
+ p1v2_bmc_aux_mon: pmic@60 {
+ compatible = "maxim,max8952";
+ reg = <0x60>;
+ max8952,default-mode = <3>;
+ max8952,dvs-mode-microvolt = <1100000>, <1100000>,
+ <1100000>, <1100000>;
+ max8952,sync-freq = <0>;
+ max8952,ramp-speed = <0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&i2cmux8 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan10_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan10_ssb: sw0 {
+ regulator-name = "fan10_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan12_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan12_ssb: sw0 {
+ regulator-name = "fan12_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan14_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan14_ssb: sw0 {
+ regulator-name = "fan14_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan16_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan16_ssb: sw0 {
+ regulator-name = "fan16_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan18_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan18_ssb: sw0 {
+ regulator-name = "fan18_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan20_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan20_ssb: sw0 {
+ regulator-name = "fan20_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan22_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan22_ssb: sw0 {
+ regulator-name = "fan22_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan24_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan24_ssb: sw0 {
+ regulator-name = "fan24_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+};
+
+&i2cmux7 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan17_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan17_ssb: sw0 {
+ regulator-name = "fan17_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan19_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan19_ssb: sw0 {
+ regulator-name = "fan19_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan21_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan21_ssb: sw0 {
+ regulator-name = "fan21_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan23_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan23_ssb: sw0 {
+ regulator-name = "fan23_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan02_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan02_ssb: sw0 {
+ regulator-name = "fan02_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan04_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan04_ssb: sw0 {
+ regulator-name = "fan04_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan06_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan06_ssb: sw0 {
+ regulator-name = "fan06_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan08_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan08_ssb: sw0 {
+ regulator-name = "fan08_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+};
+
+&i2cmux6 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan01_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan01_ssb: sw0 {
+ regulator-name = "fan01_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan03_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan03_ssb: sw0 {
+ regulator-name = "fan03_supply";
+
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan05_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan05_ssb: sw0 {
+ regulator-name = "fan05_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan07_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan07_ssb: sw0 {
+ regulator-name = "fan07_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan09_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan09_ssb: sw0 {
+ regulator-name = "fan09_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan11_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan11_ssb: sw0 {
+ regulator-name = "fan11_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan13_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan13_ssb: sw0 {
+ regulator-name = "fan13_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan15_ssb: regulator@3a {
+ compatible = "maxim,max5978";
+ reg = <0x3a>;
+ vss1-supply = <&p12v>;
+ interrupt-parent = <&smb_svc_pex_fan_alert>;
+ interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ sw0_fan15_ssb: sw0 {
+ regulator-name = "fan15_supply";
+ shunt-resistor-micro-ohms = <10000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <3400000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+
+ };
+};
+
+&i2cmux9 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd19: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <46 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd19:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd19: sw0 {
+ regulator-name = "rssd19_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd19: sw1 {
+ regulator-name = "rssd19_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd18: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <45 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd18:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd18: sw0 {
+ regulator-name = "rssd18_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd18: sw1 {
+ regulator-name = "rssd18_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd17: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <44 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd17:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd17: sw0 {
+ regulator-name = "rssd17_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd17: sw1 {
+ regulator-name = "rssd17_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd20: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <47 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd20:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd20: sw0 {
+ regulator-name = "rssd20_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd20: sw1 {
+ regulator-name = "rssd20_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd21: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <48 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd21:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd21: sw0 {
+ regulator-name = "rssd21_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd21: sw1 {
+ regulator-name = "rssd21_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd22: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <49 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd22:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd22: sw0 {
+ regulator-name = "rssd22_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd22: sw1 {
+ regulator-name = "rssd22_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd24: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <51 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd24:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd24: sw0 {
+ regulator-name = "rssd24_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd24: sw1 {
+ regulator-name = "rssd24_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd23: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <50 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd23:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd23: sw0 {
+ regulator-name = "rssd23_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd23: sw1 {
+ regulator-name = "rssd23_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+};
+
+&i2cmux10 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd25: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <52 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd25:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd25: sw0 {
+ regulator-name = "rssd25_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd25: sw1 {
+ regulator-name = "rssd25_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd26: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <53 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd26:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd26: sw0 {
+ regulator-name = "rssd26_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd26: sw1 {
+ regulator-name = "rssd26_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd27: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <54 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd27:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd27: sw0 {
+ regulator-name = "rssd27_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd27: sw1 {
+ regulator-name = "rssd27_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd32: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd32:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd32: sw0 {
+ regulator-name = "rssd32_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd32: sw1 {
+ regulator-name = "rssd32_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd31: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <58 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd31:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd31: sw0 {
+ regulator-name = "rssd31_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd31: sw1 {
+ regulator-name = "rssd31_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd30: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <57 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd30:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd30: sw0 {
+ regulator-name = "rssd30_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd30: sw1 {
+ regulator-name = "rssd30_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd29: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd29:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd29: sw0 {
+ regulator-name = "rssd29_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd29: sw1 {
+ regulator-name = "rssd29_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd28: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd17_32>;
+ interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd28:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd28: sw0 {
+ regulator-name = "rssd28_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd28: sw1 {
+ regulator-name = "rssd28_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+};
+
+&i2cmux18 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd03: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <46 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd03:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd03: sw0 {
+ regulator-name = "rssd03_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd03: sw1 {
+ regulator-name = "rssd03_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd02: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <45 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd02:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd02: sw0 {
+ regulator-name = "rssd02_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd02: sw1 {
+ regulator-name = "rssd02_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd01: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <44 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd01:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd01: sw0 {
+ regulator-name = "rssd01_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd01: sw1 {
+ regulator-name = "rssd01_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd04: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <47 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd04:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd04: sw0 {
+ regulator-name = "rssd04_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd04: sw1 {
+ regulator-name = "rssd04_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd05: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <48 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd05:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd05: sw0 {
+ regulator-name = "rssd05_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd05: sw1 {
+ regulator-name = "rssd05_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd08: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <51 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd08:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd08: sw0 {
+ regulator-name = "rssd08_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd08: sw1 {
+ regulator-name = "rssd08_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd07: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <50 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd07:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd07: sw0 {
+ regulator-name = "rssd07_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd07: sw1 {
+ regulator-name = "rssd07_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd06: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <49 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd06:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd06: sw0 {
+ regulator-name = "rssd06_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd06: sw1 {
+ regulator-name = "rssd06_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+};
+
+&i2cmux19 {
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd14: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <57 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd14:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd14: sw0 {
+ regulator-name = "rssd14_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd14: sw1 {
+ regulator-name = "rssd14_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd13: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd13:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd13: sw0 {
+ regulator-name = "rssd13_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd13: sw1 {
+ regulator-name = "rssd13_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd12: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd12:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd12: sw0 {
+ regulator-name = "rssd12_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd12: sw1 {
+ regulator-name = "rssd12_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd11: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <54 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd11:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd11: sw0 {
+ regulator-name = "rssd11_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd11: sw1 {
+ regulator-name = "rssd11_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd10: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <53 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd10:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd10: sw0 {
+ regulator-name = "rssd10_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd10: sw1 {
+ regulator-name = "rssd10_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd09: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <52 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd09:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd09: sw0 {
+ regulator-name = "rssd09_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd09: sw1 {
+ regulator-name = "rssd09_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd15: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <58 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd15:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd15: sw0 {
+ regulator-name = "rssd15_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd15: sw1 {
+ regulator-name = "rssd15_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssb_rssd16: regulator@3a {
+ compatible = "maxim,max5970";
+ reg = <0x3a>;
+ interrupt-parent = <&smb_svc_pex_rssd01_16>;
+ interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
+
+ vss1-supply = <&p3v3_aux>;
+ vss2-supply = <&p12v>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "rssd16:green:power";
+ default-state = "off";
+ };
+ };
+
+ regulators {
+ sw0_ssb_rssd16: sw0 {
+ regulator-name = "rssd16_12v";
+ shunt-resistor-micro-ohms = <9000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <4500000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ sw1_ssb_rssd16: sw1 {
+ regulator-name = "rssd16_3v3";
+ shunt-resistor-micro-ohms = <100000>;
+ regulator-over-current-protection;
+ regulator-oc-protection-microamp = <410000>;
+ regulator-enable-ramp-delay = <1000>;
+ };
+ };
+ };
+ };
+};
--
2.42.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
2024-10-02 8:40 [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Naresh Solanki
2024-10-02 8:40 ` [PATCH v3 2/2] ARM: dts: aspeed: sbp1: IBM sbp1 BMC board Naresh Solanki
@ 2024-10-02 21:45 ` Rob Herring (Arm)
2024-10-02 23:43 ` Andrew Jeffery
2024-10-03 8:16 ` Krzysztof Kozlowski
2024-10-03 8:17 ` Krzysztof Kozlowski
3 siblings, 1 reply; 8+ messages in thread
From: Rob Herring (Arm) @ 2024-10-02 21:45 UTC (permalink / raw)
To: Naresh Solanki
Cc: linux-aspeed, Conor Dooley, linux-arm-kernel, linux-kernel,
Joel Stanley, devicetree, Andrew Jeffery, Krzysztof Kozlowski
On Wed, 02 Oct 2024 14:10:17 +0530, Naresh Solanki wrote:
> Document the new compatibles used on IBM SBP1.
>
> Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
> ---
> Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y aspeed/aspeed-bmc-ibm-sbp1.dtb' for 20241002084023.467383-1-naresh.solanki@9elements.com:
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: bus@1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mdio@1e650010: Unevaluated properties are not allowed ('reset-assert-us', 'reset-deassert-us' were unexpected)
from schema $id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mdio@1e650018: Unevaluated properties are not allowed ('reset-assert-us', 'reset-deassert-us' were unexpected)
from schema $id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: syscon@1e6e2000: 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: adc@1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: adc@1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: crypto@1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/video@1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: gpio@1e780000: 'gpio-reserved-ranges' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: lpc@1e789000: lpc-snoop@80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: lpc@1e789000: reg-io-width: 4 is not of type 'object'
from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: sdc@1e740000: sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: sdc@1e740000: sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-pvcore-nic2@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-pvcore-nic1@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p3v3-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p1v2-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p1v8-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/bus@1e78a000/i2c@280/bmc-slave@10: failed to match any schema with compatible: ['ipmb-dev']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: r38263-p1v05-pch-aux@40: Unevaluated properties are not allowed ('interrupt-parent', 'interrupts', 'regulators' were unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38060-p1v8-pch-aux@40: Unevaluated properties are not allowed ('interrupt-parent', 'interrupts', 'regulators' were unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mux@77: interrupts: False schema does not allow [[44, 4]]
from schema $id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu2@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu2@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu1@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu1@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu3@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu3@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p5v-aux@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p3v3-aux@40: Unevaluated properties are not allowed ('regulators' was unexpected)
from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu0@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu0@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: fsi@1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: fsi@1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
2024-10-02 21:45 ` [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Rob Herring (Arm)
@ 2024-10-02 23:43 ` Andrew Jeffery
2024-10-07 10:30 ` Naresh Solanki
0 siblings, 1 reply; 8+ messages in thread
From: Andrew Jeffery @ 2024-10-02 23:43 UTC (permalink / raw)
To: Naresh Solanki
Cc: linux-aspeed, Conor Dooley, linux-arm-kernel, linux-kernel,
Joel Stanley, devicetree, Krzysztof Kozlowski, Rob Herring (Arm)
Hi Naresh,
On Wed, 2024-10-02 at 16:45 -0500, Rob Herring (Arm) wrote:
> On Wed, 02 Oct 2024 14:10:17 +0530, Naresh Solanki wrote:
> > Document the new compatibles used on IBM SBP1.
> >
> > Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
> > ---
> > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> > 1 file changed, 1 insertion(+)
> >
>
>
> My bot found new DTB warnings on the .dts files added or changed in this
> series.
>
> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
> are fixed by another series. Ultimately, it is up to the platform
> maintainer whether these warnings are acceptable or not. No need to reply
> unless the platform maintainer has comments.
>
> If you already ran DT checks and didn't see these error(s), then
> make sure dt-schema is up to date:
>
> pip3 install dtschema --upgrade
>
>
> New warnings running 'make CHECK_DTBS=y aspeed/aspeed-bmc-ibm-sbp1.dtb' for 20241002084023.467383-1-naresh.solanki@9elements.com:
A bunch of what follows are issues caused by the lack of dt-schema
bindings for the ASPEED SoC peripherals. You can ignore those errors
for now.
However, some of those below are specific to your devicetree. Can you
please address them?
>
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: bus@1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
> from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
For instance, ignore the above for now.
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mdio@1e650010: Unevaluated properties are not allowed ('reset-assert-us', 'reset-deassert-us' were unexpected)
> from schema $id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mdio@1e650018: Unevaluated properties are not allowed ('reset-assert-us', 'reset-deassert-us' were unexpected)
> from schema $id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml#
Check the bindings regarding these - it seems they should go in a phy
subnode of the MDIO controller.
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: syscon@1e6e2000: 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: adc@1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: adc@1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: crypto@1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/video@1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
Ignore the above for now.
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: gpio@1e780000: 'gpio-reserved-ranges' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
I'm not sure why this one is flagged, though it is one you should
resolve. You might need some input from the devicetree maintainers.
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: lpc@1e789000: lpc-snoop@80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: lpc@1e789000: reg-io-width: 4 is not of type 'object'
> from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: sdc@1e740000: sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
> from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: sdc@1e740000: sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
> from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
Ignore the above for now.
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-pvcore-nic2@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-pvcore-nic1@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p3v3-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p1v2-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p1v8-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/bus@1e78a000/i2c@280/bmc-slave@10: failed to match any schema with compatible: ['ipmb-dev']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: r38263-p1v05-pch-aux@40: Unevaluated properties are not allowed ('interrupt-parent', 'interrupts', 'regulators' were unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38060-p1v8-pch-aux@40: Unevaluated properties are not allowed ('interrupt-parent', 'interrupts', 'regulators' were unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mux@77: interrupts: False schema does not allow [[44, 4]]
> from schema $id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu2@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu2@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu1@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu1@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu3@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu3@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p5v-aux@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p3v3-aux@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu0@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu0@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
These all look like they need to be addressed.
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: fsi@1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
> from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: fsi@1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
> from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
> arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
>
Ignore these for now.
Andrew
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
2024-10-02 8:40 [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Naresh Solanki
2024-10-02 8:40 ` [PATCH v3 2/2] ARM: dts: aspeed: sbp1: IBM sbp1 BMC board Naresh Solanki
2024-10-02 21:45 ` [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Rob Herring (Arm)
@ 2024-10-03 8:16 ` Krzysztof Kozlowski
2024-10-03 8:17 ` Krzysztof Kozlowski
3 siblings, 0 replies; 8+ messages in thread
From: Krzysztof Kozlowski @ 2024-10-03 8:16 UTC (permalink / raw)
To: Naresh Solanki
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel
On Wed, Oct 02, 2024 at 02:10:17PM +0530, Naresh Solanki wrote:
> Document the new compatibles used on IBM SBP1.
>
> Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
> ---
Provide changelog explaining what happened here, including what changed
that tag is invalid/skipped.
<form letter>
This is a friendly reminder during the review process.
It looks like you received a tag and forgot to add it.
If you do not know the process, here is a short explanation: Please add
Acked-by/Reviewed-by/Tested-by tags when posting new versions, under
or above your Signed-off-by tag. Tag is "received", when provided
in a message replied to you on the mailing list. Tools like b4 can help
here. However, there's no need to repost patches *only* to add the tags.
The upstream maintainer will do that for tags received on the version
they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
If a tag was not added on purpose, please state why and what changed.
</form letter>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
2024-10-02 8:40 [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Naresh Solanki
` (2 preceding siblings ...)
2024-10-03 8:16 ` Krzysztof Kozlowski
@ 2024-10-03 8:17 ` Krzysztof Kozlowski
2024-10-07 10:32 ` Naresh Solanki
3 siblings, 1 reply; 8+ messages in thread
From: Krzysztof Kozlowski @ 2024-10-03 8:17 UTC (permalink / raw)
To: Naresh Solanki
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel
On Wed, Oct 02, 2024 at 02:10:17PM +0530, Naresh Solanki wrote:
> Document the new compatibles used on IBM SBP1.
>
> Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
> ---
> Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> index 95113df178cc..8c04d6eaec08 100644
> --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> @@ -89,6 +89,7 @@ properties:
> - ibm,everest-bmc
> - ibm,rainier-bmc
> - ibm,system1-bmc
> + - ibm,sbp1-bmc
Keep alphabetical order.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
2024-10-02 23:43 ` Andrew Jeffery
@ 2024-10-07 10:30 ` Naresh Solanki
0 siblings, 0 replies; 8+ messages in thread
From: Naresh Solanki @ 2024-10-07 10:30 UTC (permalink / raw)
To: Andrew Jeffery
Cc: linux-aspeed, Conor Dooley, linux-arm-kernel, linux-kernel,
Joel Stanley, devicetree, Krzysztof Kozlowski, Rob Herring (Arm),
Guenter Roeck
Hi Andrew,
+Guenter Roeck
On Thu, 3 Oct 2024 at 05:13, Andrew Jeffery <andrew@codeconstruct.com.au> wrote:
>
> Hi Naresh,
>
> On Wed, 2024-10-02 at 16:45 -0500, Rob Herring (Arm) wrote:
> > On Wed, 02 Oct 2024 14:10:17 +0530, Naresh Solanki wrote:
> > > Document the new compatibles used on IBM SBP1.
> > >
> > > Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
> > > ---
> > > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> > > 1 file changed, 1 insertion(+)
> > >
> >
> >
> > My bot found new DTB warnings on the .dts files added or changed in this
> > series.
> >
> > Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
> > are fixed by another series. Ultimately, it is up to the platform
> > maintainer whether these warnings are acceptable or not. No need to reply
> > unless the platform maintainer has comments.
> >
> > If you already ran DT checks and didn't see these error(s), then
> > make sure dt-schema is up to date:
> >
> > pip3 install dtschema --upgrade
> >
> >
> > New warnings running 'make CHECK_DTBS=y aspeed/aspeed-bmc-ibm-sbp1.dtb' for 20241002084023.467383-1-naresh.solanki@9elements.com:
>
> A bunch of what follows are issues caused by the lack of dt-schema
> bindings for the ASPEED SoC peripherals. You can ignore those errors
> for now.
>
> However, some of those below are specific to your devicetree. Can you
> please address them?
Sure
>
> >
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: bus@1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
> > from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
>
> For instance, ignore the above for now.
ok
>
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mdio@1e650010: Unevaluated properties are not allowed ('reset-assert-us', 'reset-deassert-us' were unexpected)
> > from schema $id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mdio@1e650018: Unevaluated properties are not allowed ('reset-assert-us', 'reset-deassert-us' were unexpected)
> > from schema $id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml#
>
> Check the bindings regarding these - it seems they should go in a phy
> subnode of the MDIO controller.
Yes. You're absolutely right. These should be under the phy node. Will
update in the next patchset.
>
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: syscon@1e6e2000: 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: adc@1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: adc@1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: crypto@1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/video@1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
>
> Ignore the above for now.
ok
>
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: gpio@1e780000: 'gpio-reserved-ranges' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
>
> I'm not sure why this one is flagged, though it is one you should
> resolve. You might need some input from the devicetree maintainers.
ok.
>
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: lpc@1e789000: lpc-snoop@80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: lpc@1e789000: reg-io-width: 4 is not of type 'object'
> > from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: kcs@114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: sdc@1e740000: sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
> > from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: sdc@1e740000: sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
> > from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
>
> Ignore the above for now.
ok
>
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-pvcore-nic2@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-pvcore-nic1@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p3v3-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p1v2-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p1v8-nic@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/bus@1e78a000/i2c@280/bmc-slave@10: failed to match any schema with compatible: ['ipmb-dev']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: r38263-p1v05-pch-aux@40: Unevaluated properties are not allowed ('interrupt-parent', 'interrupts', 'regulators' were unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38060-p1v8-pch-aux@40: Unevaluated properties are not allowed ('interrupt-parent', 'interrupts', 'regulators' were unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mux@77: interrupts: False schema does not allow [[44, 4]]
> > from schema $id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu2@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu2@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu1@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu1@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu3@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu3@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p5v-aux@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: ir38263-p3v3-aux@40: Unevaluated properties are not allowed ('regulators' was unexpected)
> > from schema $id: http://devicetree.org/schemas/regulator/infineon,ir38060.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: regulator@5f: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: pvccinfaon-pvccfa-cpu0@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: mp2973-pvccin-pvccfa-cpu0@58: 'regulators' does not match any of the regexes: 'pinctrl-[0-9]+'
> > from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
>
> These all look like they need to be addressed.
These seem to be applicable for all trivial devices.
I'm not sure what should be the fix.
Regards,
Naresh
>
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: fsi@1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
> > from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: fsi@1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
> > from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
> > arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dtb: /ahb/apb/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
> >
>
> Ignore these for now.
>
> Andrew
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board
2024-10-03 8:17 ` Krzysztof Kozlowski
@ 2024-10-07 10:32 ` Naresh Solanki
0 siblings, 0 replies; 8+ messages in thread
From: Naresh Solanki @ 2024-10-07 10:32 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel
Hi Krzysztof
On Thu, 3 Oct 2024 at 13:47, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>
> On Wed, Oct 02, 2024 at 02:10:17PM +0530, Naresh Solanki wrote:
> > Document the new compatibles used on IBM SBP1.
> >
> > Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
> > ---
> > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> > 1 file changed, 1 insertion(+)
> >
> > diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> > index 95113df178cc..8c04d6eaec08 100644
> > --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> > +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> > @@ -89,6 +89,7 @@ properties:
> > - ibm,everest-bmc
> > - ibm,rainier-bmc
> > - ibm,system1-bmc
> > + - ibm,sbp1-bmc
>
> Keep alphabetical order.
Sure. Will update in next patchset. Will also include Ack-by for the patch.
Thanks.
Naresh
>
> Best regards,
> Krzysztof
>
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2024-10-07 10:32 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-10-02 8:40 [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Naresh Solanki
2024-10-02 8:40 ` [PATCH v3 2/2] ARM: dts: aspeed: sbp1: IBM sbp1 BMC board Naresh Solanki
2024-10-02 21:45 ` [PATCH v3 1/2] dt-bindings: arm: aspeed: add IBM SBP1 board Rob Herring (Arm)
2024-10-02 23:43 ` Andrew Jeffery
2024-10-07 10:30 ` Naresh Solanki
2024-10-03 8:16 ` Krzysztof Kozlowski
2024-10-03 8:17 ` Krzysztof Kozlowski
2024-10-07 10:32 ` Naresh Solanki
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).