* [PATCH v2 2/2] arm64: dts: mediatek: add device-tree for Genio 700 EVK board
2023-09-13 4:04 [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: add mt8390-evk board Macpaul Lin
@ 2023-09-13 4:04 ` Macpaul Lin
2023-09-13 6:42 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: add mt8390-evk board Krzysztof Kozlowski
2023-09-13 14:36 ` Conor Dooley
2 siblings, 0 replies; 4+ messages in thread
From: Macpaul Lin @ 2023-09-13 4:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Matthias Brugger,
AngeloGioacchino Del Regno, Macpaul Lin,
Bernhard Rosenkränzer, devicetree, linux-kernel,
linux-arm-kernel, linux-mediatek
Cc: Bear Wang, Pablo Sun, Macpaul Lin, Chris-QJ Chen
Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.
The Genio 700 EVK has following features:
- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
- M.2 Key B slot
- Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../dts/mediatek/mt8390-genio-700-evk.dts | 880 ++++++++++++++++++
2 files changed, 881 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
dependencies for v1:
- This patch should be applied after the following patch set
- mt8365-gneio-350-evk's dts change (v4)
- https://lore.kernel.org/linux-arm-kernel/20230912092444.31635-1-macpaul.lin@mediatek.com/T/
- mt8395-genio-1200-evk's dts basic support (v6)
- https://lore.kernel.org/lkml/20230911115717.26184-1-macpaul.lin@mediatek.com/T/
- mt8188 platform's basic support
- https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@mediatek.com/T/
changes for v2:
- Fix gpio defines '0' to 'GPIO_ACTIVE_HIGH'.
- Drop duplicate name: 'default' for I2C4.
- Update dependencies
- mt8365-gneio-350-evk's dts change (v5)
- https://lore.kernel.org/lkml/20230913032226.4092-1-macpaul.lin@mediatek.com/
- mt8395-genio-1200-evk's dts basic support (v7)
- https://lore.kernel.org/linux-arm-kernel/20230913032057.3197-1-macpaul.lin@mediatek.com/T/
- mt8188 platform's basic support (v4)
- https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@mediatek.com/T/
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 22f362bbbdac..3262849c0f6b 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -54,5 +54,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-genio-350-evk.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8390-genio-700-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-genio-1200-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
new file mode 100644
index 000000000000..ed6bbf0c15cc
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
@@ -0,0 +1,880 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2023 MediaTek Inc.
+ * Author: Chris Chen <chris-qj.chen@mediatek.com>
+ * Pablo Sun <pablo.sun@mediatek.com>
+ * Macpaul Lin <macpaul.lin@mediatek.com>
+ */
+/dts-v1/;
+
+#include "mt8188.dtsi"
+#include "mt6359.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/mediatek,mt8188-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/usb/pd.h>
+
+/ {
+ model = "MediaTek Genio-700 EVK";
+ compatible = "mediatek,mt8390-evk", "mediatek,mt8390",
+ "mediatek,mt8188";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0x2 0x00000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /*
+ * 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee@43200000 {
+ no-map;
+ reg = <0 0x43200000 0 0x00c00000>;
+ };
+
+ scp_mem: memory@50000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x50000000 0 0x2900000>;
+ no-map;
+ };
+
+ /* 2 MiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_reserved: memory@54600000 {
+ no-map;
+ reg = <0 0x54600000 0x0 0x200000>;
+ };
+
+ apu_mem: memory@55000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x55000000 0 0x1400000>; /* 20 MB */
+ };
+
+ vpu_mem: memory@57000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x57000000 0 0x1400000>; /* 20 MB */
+ };
+ };
+
+ common_fixed_5v: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v_en";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ edp_panel_fixed_3v3: regulator-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "edp_panel_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_panel_3v3_en_pins>;
+ };
+
+ gpio_fixed_3v3: regulator-2 {
+ compatible = "regulator-fixed";
+ regulator-name = "gpio_3v3_en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ sdio_fixed_1v8: regulator-3 {
+ compatible = "regulator-fixed";
+ regulator-name = "sdio_io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ sdio_fixed_3v3: regulator-4 {
+ compatible = "regulator-fixed";
+ regulator-name = "sdio_card";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 74 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ touch0_fixed_3v3: regulator-5 {
+ compatible = "regulator-fixed";
+ regulator-name = "touch_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 119 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_hub_fixed_3v3: regulator-6 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_hub_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 112 GPIO_ACTIVE_HIGH>; /* HUB_3V3_EN */
+ startup-delay-us = <10000>;
+ enable-active-high;
+ };
+
+ usb_hub_reset_1v8: regulator-7 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_hub_reset";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&pio 7 GPIO_ACTIVE_HIGH>; /* HUB_RESET */
+ vin-supply = <&usb_hub_fixed_3v3>;
+ };
+
+ usb_p0_vbus: regulator-8 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_p0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 84 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_p1_vbus: regulator-9 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_p1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 87 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_p2_vbus: regulator-10 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_p2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ touchscreen@5d {
+ compatible = "goodix,gt9271";
+ reg = <0x5d>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+ irq-gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+ AVDD28-supply = <&touch0_fixed_3v3>;
+ VDDIO-supply = <&mt6359_vio18_ldo_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pins>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-1 = <&rt1715_int_pins>;
+ clock-frequency = <1000000>;
+ status = "okay";
+};
+
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&mmc0 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_default_pins>;
+ pinctrl-1 = <&mmc0_uhs_pins>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ supports-cqe;
+ cap-mmc-hw-reset;
+ no-sdio;
+ no-sd;
+ hs400-ds-delay = <0x1481b>;
+ vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+ vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+ non-removable;
+};
+
+&mmc1 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc1_default_pins>;
+ pinctrl-1 = <&mmc1_uhs_pins>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ no-mmc;
+ no-sdio;
+ cd-gpios = <&pio 2 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&mt6359_vpa_buck_reg>;
+ vqmmc-supply = <&mt6359_vsim1_ldo_reg>;
+};
+
+&mt6359_vbbck_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcn18_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcn33_2_bt_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcore_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vpa_buck_reg {
+ regulator-max-microvolt = <3100000>;
+};
+
+&mt6359_vpu_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vsim1_ldo_reg {
+ regulator-enable-ramp-delay = <480>;
+};
+
+&mt6359_vufs_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359codec {
+ mediatek,mic-type-0 = <1>; /* ACC */
+ mediatek,mic-type-1 = <3>; /* DCC */
+};
+
+&pio {
+ audio_default_pins: audio-default-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO101__FUNC_O_AUD_CLK_MOSI>,
+ <PINMUX_GPIO102__FUNC_O_AUD_SYNC_MOSI>,
+ <PINMUX_GPIO103__FUNC_O_AUD_DAT_MOSI0>,
+ <PINMUX_GPIO104__FUNC_O_AUD_DAT_MOSI1>,
+ <PINMUX_GPIO105__FUNC_I0_AUD_DAT_MISO0>,
+ <PINMUX_GPIO106__FUNC_I0_AUD_DAT_MISO1>,
+ <PINMUX_GPIO107__FUNC_B0_I2SIN_MCK>,
+ <PINMUX_GPIO108__FUNC_B0_I2SIN_BCK>,
+ <PINMUX_GPIO109__FUNC_B0_I2SIN_WS>,
+ <PINMUX_GPIO110__FUNC_I0_I2SIN_D0>,
+ <PINMUX_GPIO114__FUNC_O_I2SO2_MCK>,
+ <PINMUX_GPIO115__FUNC_B0_I2SO2_BCK>,
+ <PINMUX_GPIO116__FUNC_B0_I2SO2_WS>,
+ <PINMUX_GPIO117__FUNC_O_I2SO2_D0>,
+ <PINMUX_GPIO118__FUNC_O_I2SO2_D1>,
+ <PINMUX_GPIO121__FUNC_B0_PCM_CLK>,
+ <PINMUX_GPIO122__FUNC_B0_PCM_SYNC>,
+ <PINMUX_GPIO124__FUNC_I0_PCM_DI>,
+ <PINMUX_GPIO125__FUNC_O_DMIC1_CLK>,
+ <PINMUX_GPIO126__FUNC_I0_DMIC1_DAT>,
+ <PINMUX_GPIO128__FUNC_O_DMIC2_CLK>,
+ <PINMUX_GPIO129__FUNC_I0_DMIC2_DAT>;
+ };
+ };
+
+ dptx_pins: dptx-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO46__FUNC_I0_DP_TX_HPD>;
+ bias-pull-up;
+ };
+ };
+
+ edp_panel_3v3_en_pins: edp-panel-3v3-en-pins {
+ pins1 {
+ pinmux = <PINMUX_GPIO15__FUNC_B_GPIO15>;
+ output-high;
+ };
+ };
+
+ eth_default_pins: eth-default-pins {
+ pins-cc {
+ pinmux = <PINMUX_GPIO139__FUNC_B0_GBE_TXC>,
+ <PINMUX_GPIO140__FUNC_I0_GBE_RXC>,
+ <PINMUX_GPIO141__FUNC_I0_GBE_RXDV>,
+ <PINMUX_GPIO142__FUNC_O_GBE_TXEN>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+
+ pins-mdio {
+ pinmux = <PINMUX_GPIO143__FUNC_O_GBE_MDC>,
+ <PINMUX_GPIO144__FUNC_B1_GBE_MDIO>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ input-enable;
+ };
+
+ pins-power {
+ pinmux = <PINMUX_GPIO145__FUNC_B_GPIO145>,
+ <PINMUX_GPIO146__FUNC_B_GPIO146>;
+ output-high;
+ };
+
+ pins-rxd {
+ pinmux = <PINMUX_GPIO135__FUNC_I0_GBE_RXD3>,
+ <PINMUX_GPIO136__FUNC_I0_GBE_RXD2>,
+ <PINMUX_GPIO137__FUNC_I0_GBE_RXD1>,
+ <PINMUX_GPIO138__FUNC_I0_GBE_RXD0>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+
+ pins-txd {
+ pinmux = <PINMUX_GPIO131__FUNC_O_GBE_TXD3>,
+ <PINMUX_GPIO132__FUNC_O_GBE_TXD2>,
+ <PINMUX_GPIO133__FUNC_O_GBE_TXD1>,
+ <PINMUX_GPIO134__FUNC_O_GBE_TXD0>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+ };
+
+ eth_sleep_pins: eth-sleep-pins {
+ pins-cc {
+ pinmux = <PINMUX_GPIO139__FUNC_B_GPIO139>,
+ <PINMUX_GPIO140__FUNC_B_GPIO140>,
+ <PINMUX_GPIO141__FUNC_B_GPIO141>,
+ <PINMUX_GPIO142__FUNC_B_GPIO142>;
+ };
+
+ pins-mdio {
+ pinmux = <PINMUX_GPIO143__FUNC_B_GPIO143>,
+ <PINMUX_GPIO144__FUNC_B_GPIO144>;
+ input-disable;
+ bias-disable;
+ };
+
+ pins-rxd {
+ pinmux = <PINMUX_GPIO135__FUNC_B_GPIO135>,
+ <PINMUX_GPIO136__FUNC_B_GPIO136>,
+ <PINMUX_GPIO137__FUNC_B_GPIO137>,
+ <PINMUX_GPIO138__FUNC_B_GPIO138>;
+ };
+
+ pins-txd {
+ pinmux = <PINMUX_GPIO131__FUNC_B_GPIO131>,
+ <PINMUX_GPIO132__FUNC_B_GPIO132>,
+ <PINMUX_GPIO133__FUNC_B_GPIO133>,
+ <PINMUX_GPIO134__FUNC_B_GPIO134>;
+ };
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>,
+ <PINMUX_GPIO55__FUNC_B1_SCL0>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c1_pins: i2c1-pins {
+ pins {
+ pinmux = <PINMUX_GPIO58__FUNC_B1_SDA1>,
+ <PINMUX_GPIO57__FUNC_B1_SCL1>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c2_pins: i2c2-pins {
+ pins {
+ pinmux = <PINMUX_GPIO60__FUNC_B1_SDA2>,
+ <PINMUX_GPIO59__FUNC_B1_SCL2>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c3_pins: i2c3-pins {
+ pins {
+ pinmux = <PINMUX_GPIO62__FUNC_B1_SDA3>,
+ <PINMUX_GPIO61__FUNC_B1_SCL3>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c4_pins: i2c4-pins {
+ pins {
+ pinmux = <PINMUX_GPIO64__FUNC_B1_SDA4>,
+ <PINMUX_GPIO63__FUNC_B1_SCL4>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c5_pins: i2c5-pins {
+ pins {
+ pinmux = <PINMUX_GPIO66__FUNC_B1_SDA5>,
+ <PINMUX_GPIO65__FUNC_B1_SCL5>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c6_pins: i2c6-pins {
+ pins {
+ pinmux = <PINMUX_GPIO68__FUNC_B1_SDA6>,
+ <PINMUX_GPIO67__FUNC_B1_SCL6>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ gpio_key_pins: gpio-key-pins {
+ pins {
+ pinmux = <PINMUX_GPIO42__FUNC_B1_KPCOL0>,
+ <PINMUX_GPIO43__FUNC_B1_KPCOL1>,
+ <PINMUX_GPIO44__FUNC_B1_KPROW0>;
+ };
+ };
+
+ mmc0_default_pins: mmc0-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO157__FUNC_B1_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO161__FUNC_B1_MSDC0_DAT0>,
+ <PINMUX_GPIO160__FUNC_B1_MSDC0_DAT1>,
+ <PINMUX_GPIO159__FUNC_B1_MSDC0_DAT2>,
+ <PINMUX_GPIO158__FUNC_B1_MSDC0_DAT3>,
+ <PINMUX_GPIO154__FUNC_B1_MSDC0_DAT4>,
+ <PINMUX_GPIO153__FUNC_B1_MSDC0_DAT5>,
+ <PINMUX_GPIO152__FUNC_B1_MSDC0_DAT6>,
+ <PINMUX_GPIO151__FUNC_B1_MSDC0_DAT7>,
+ <PINMUX_GPIO156__FUNC_B1_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO155__FUNC_O_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc0_uhs_pins: mmc0-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO157__FUNC_B1_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO161__FUNC_B1_MSDC0_DAT0>,
+ <PINMUX_GPIO160__FUNC_B1_MSDC0_DAT1>,
+ <PINMUX_GPIO159__FUNC_B1_MSDC0_DAT2>,
+ <PINMUX_GPIO158__FUNC_B1_MSDC0_DAT3>,
+ <PINMUX_GPIO154__FUNC_B1_MSDC0_DAT4>,
+ <PINMUX_GPIO153__FUNC_B1_MSDC0_DAT5>,
+ <PINMUX_GPIO152__FUNC_B1_MSDC0_DAT6>,
+ <PINMUX_GPIO151__FUNC_B1_MSDC0_DAT7>,
+ <PINMUX_GPIO156__FUNC_B1_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-ds {
+ pinmux = <PINMUX_GPIO162__FUNC_B0_MSDC0_DSL>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO155__FUNC_O_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc1_default_pins: mmc1-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO164__FUNC_B1_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO163__FUNC_B1_MSDC1_CMD>,
+ <PINMUX_GPIO165__FUNC_B1_MSDC1_DAT0>,
+ <PINMUX_GPIO166__FUNC_B1_MSDC1_DAT1>,
+ <PINMUX_GPIO167__FUNC_B1_MSDC1_DAT2>,
+ <PINMUX_GPIO168__FUNC_B1_MSDC1_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-insert {
+ pinmux = <PINMUX_GPIO2__FUNC_B_GPIO2>;
+ bias-pull-up;
+ };
+ };
+
+ mmc1_uhs_pins: mmc1-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO164__FUNC_B1_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO163__FUNC_B1_MSDC1_CMD>,
+ <PINMUX_GPIO165__FUNC_B1_MSDC1_DAT0>,
+ <PINMUX_GPIO166__FUNC_B1_MSDC1_DAT1>,
+ <PINMUX_GPIO167__FUNC_B1_MSDC1_DAT2>,
+ <PINMUX_GPIO168__FUNC_B1_MSDC1_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc2_default_pins: mmc2-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO170__FUNC_B1_MSDC2_CLK>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO169__FUNC_B1_MSDC2_CMD>,
+ <PINMUX_GPIO171__FUNC_B1_MSDC2_DAT0>,
+ <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>,
+ <PINMUX_GPIO173__FUNC_B1_MSDC2_DAT2>,
+ <PINMUX_GPIO174__FUNC_B1_MSDC2_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-pcm {
+ pinmux = <PINMUX_GPIO123__FUNC_O_PCM_DO>;
+ };
+ };
+
+ mmc2_uhs_pins: mmc2-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO170__FUNC_B1_MSDC2_CLK>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO169__FUNC_B1_MSDC2_CMD>,
+ <PINMUX_GPIO171__FUNC_B1_MSDC2_DAT0>,
+ <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>,
+ <PINMUX_GPIO173__FUNC_B1_MSDC2_DAT2>,
+ <PINMUX_GPIO174__FUNC_B1_MSDC2_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc2_eint_pins: mmc2-eint-pins {
+ pins-dat1 {
+ pinmux = <PINMUX_GPIO172__FUNC_B_GPIO172>;
+ input-enable;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc2_dat1_pins: mmc2-dat1-pins {
+ pins-dat1 {
+ pinmux = <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ panel_default_pins: panel-default-pins {
+ pins-dcdc {
+ pinmux = <PINMUX_GPIO45__FUNC_B_GPIO45>;
+ output-low;
+ };
+
+ pins-en {
+ pinmux = <PINMUX_GPIO111__FUNC_B_GPIO111>;
+ output-low;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO25__FUNC_B_GPIO25>;
+ output-high;
+ };
+ };
+
+ rt1715_int_pins: rt1715-int-pins {
+ pins_cmd0_dat {
+ pinmux = <PINMUX_GPIO12__FUNC_B_GPIO12>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+
+ spi0_pins: spi0-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO69__FUNC_O_SPIM0_CSB>,
+ <PINMUX_GPIO70__FUNC_O_SPIM0_CLK>,
+ <PINMUX_GPIO71__FUNC_B0_SPIM0_MOSI>,
+ <PINMUX_GPIO72__FUNC_B0_SPIM0_MISO>;
+ bias-disable;
+ };
+ };
+
+ spi1_pins: spi1-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO75__FUNC_O_SPIM1_CSB>,
+ <PINMUX_GPIO76__FUNC_O_SPIM1_CLK>,
+ <PINMUX_GPIO77__FUNC_B0_SPIM1_MOSI>,
+ <PINMUX_GPIO78__FUNC_B0_SPIM1_MISO>;
+ bias-disable;
+ };
+ };
+
+ spi2_pins: spi2-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO79__FUNC_O_SPIM2_CSB>,
+ <PINMUX_GPIO80__FUNC_O_SPIM2_CLK>,
+ <PINMUX_GPIO81__FUNC_B0_SPIM2_MOSI>,
+ <PINMUX_GPIO82__FUNC_B0_SPIM2_MISO>;
+ bias-disable;
+ };
+ };
+
+ touch_pins: touch-pins {
+ pins-irq {
+ pinmux = <PINMUX_GPIO6__FUNC_B_GPIO6>;
+ input-enable;
+ bias-disable;
+ };
+
+ pins-reset {
+ pinmux = <PINMUX_GPIO5__FUNC_B_GPIO5>;
+ output-high;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO31__FUNC_O_UTXD0>,
+ <PINMUX_GPIO32__FUNC_I1_URXD0>;
+ bias-pull-up;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins {
+ pinmux = <PINMUX_GPIO33__FUNC_O_UTXD1>,
+ <PINMUX_GPIO34__FUNC_I1_URXD1>;
+ bias-pull-up;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ pins {
+ pinmux = <PINMUX_GPIO35__FUNC_O_UTXD2>,
+ <PINMUX_GPIO36__FUNC_I1_URXD2>;
+ bias-pull-up;
+ };
+ };
+
+ usb_default_pins: usb-default-pins {
+ pins-iddig {
+ pinmux = <PINMUX_GPIO83__FUNC_B_GPIO83>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-valid {
+ pinmux = <PINMUX_GPIO85__FUNC_I0_VBUSVALID>;
+ input-enable;
+ };
+
+ pins-vbus {
+ pinmux = <PINMUX_GPIO84__FUNC_O_USB_DRVVBUS>;
+ output-high;
+ };
+
+ };
+
+ usb1_default_pins: usb1-default-pins {
+ pins-valid {
+ pinmux = <PINMUX_GPIO88__FUNC_I0_VBUSVALID_1P>;
+ input-enable;
+ };
+
+ pins-usb-hub-3v3-en {
+ pinmux = <PINMUX_GPIO112__FUNC_B_GPIO112>;
+ output-high;
+ };
+ };
+
+ wifi_pwrseq_pins: wifi-pwrseq-pins {
+ pins-wifi-enable {
+ pinmux = <PINMUX_GPIO127__FUNC_B_GPIO127>;
+ output-low;
+ };
+ };
+};
+
+&pmic {
+ interrupt-parent = <&pio>;
+ interrupts = <222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&scp {
+ memory-region = <&scp_mem>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-0 = <&spi2_pins>;
+ pinctrl-names = "default";
+ mediatek,pad-select = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+};
+
+&u3phy0 {
+ status = "okay";
+};
+
+&u3phy1 {
+ status = "okay";
+};
+
+&u3phy2 {
+ status = "okay";
+};
+
+&xhci0 {
+ status = "okay";
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+};
+
+&xhci1 {
+ status = "okay";
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+ vbus-supply = <&usb_hub_reset_1v8>;
+};
+
+&xhci2 {
+ status = "okay";
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+};
--
2.18.0
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: add mt8390-evk board
2023-09-13 4:04 [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: add mt8390-evk board Macpaul Lin
2023-09-13 4:04 ` [PATCH v2 2/2] arm64: dts: mediatek: add device-tree for Genio 700 EVK board Macpaul Lin
2023-09-13 6:42 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: add mt8390-evk board Krzysztof Kozlowski
@ 2023-09-13 14:36 ` Conor Dooley
2 siblings, 0 replies; 4+ messages in thread
From: Conor Dooley @ 2023-09-13 14:36 UTC (permalink / raw)
To: Macpaul Lin
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Matthias Brugger,
AngeloGioacchino Del Regno, Bernhard Rosenkränzer,
devicetree, linux-kernel, linux-arm-kernel, linux-mediatek,
Bear Wang, Pablo Sun, Macpaul Lin
[-- Attachment #1: Type: text/plain, Size: 2393 bytes --]
Yo,
For $subject, the "dts: " can be dropped.
On Wed, Sep 13, 2023 at 12:04:48PM +0800, Macpaul Lin wrote:
> 1. Add compatible for MT8390.
> 2. Add bindings for the MediaTek mt8390-evk board, also known
> as the "Genio 700-EVK".
>
> The MT8390 and MT8188 belong to the same SoC family,
> with only minor differences in their physical characteristics.
> They utilize unique efuse values for differentiation.
>
> The booting process and configurations are managed by boot
> loaders, firmware, and TF-A. Consequently, the part numbers
> and procurement channels vary.
>
> Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
> ---
> Documentation/devicetree/bindings/arm/mediatek.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
> dependencies for v1:
> - This patch should be applied after the following patch set
> - mt8365's bindings
> - https://lore.kernel.org/linux-arm-kernel/20230912092444.31635-1-macpaul.lin@mediatek.com/T/
> - mt8395's bindings: v6
> - https://lore.kernel.org/lkml/20230911115717.26184-1-macpaul.lin@mediatek.com/T/
> - mt8188's bindings
> - https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@mediatek.com/T/
>
> Changess for v2:
> - drop description for multiple boards
> - update dependencies with the following patch sets
> - mt8395's bindings: v7
> - https://lore.kernel.org/linux-arm-kernel/20230913032057.3197-1-macpaul.lin@mediatek.com/T/
>
> diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
> index 0248bb458180..3968d5934fa2 100644
> --- a/Documentation/devicetree/bindings/arm/mediatek.yaml
> +++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
> @@ -252,6 +252,11 @@ properties:
> - enum:
> - mediatek,mt8365-evk
> - const: mediatek,mt8365
> + - items:
> + - enum:
> + - mediatek,mt8390-evk
> + - const: mediatek,mt8390
> + - const: mediatek,mt8188
This is prob a little unusual (at least I don't think I've seen a patch
doing this so far), but the mediatek maintainers can do as they wish
here I think.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Thanks,
Conor.
> - items:
> - enum:
> - mediatek,mt8395-evk
> --
> 2.18.0
>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread