Devicetree
 help / color / mirror / Atom feed
From: Bryan O'Donoghue <bod@kernel.org>
To: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>,
	Bryan O'Donoghue <bryan.odonoghue@linaro.org>,
	Vinod Koul <vkoul@kernel.org>,
	Kishon Vijay Abraham I <kishon@kernel.org>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Neil Armstrong <neil.armstrong@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
	linux-media@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Subject: Re: [PATCH v13 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema
Date: Tue, 21 Jul 2026 11:47:15 +0100	[thread overview]
Message-ID: <c236cf94-a775-4158-88db-9a337c7fa862@kernel.org> (raw)
In-Reply-To: <345ca98e-09f6-4965-87bb-e64dac096498@linaro.org>

On 21/07/2026 10:56, Vladimir Zapolskiy wrote:
> On 7/21/26 12:39, Bryan O'Donoghue wrote:
>> On 21/07/2026 09:17, Vladimir Zapolskiy wrote:
>>>> +  "#phy-cells":
>>>> +    const: 1
>>>> +    description:
>>>> +      The single cell specifies the PHY operating mode.
>>> This has been reported before, #phy-cells shall be 0, the operation
>>> mode is selected by bus-type of endpoints as it is described in
>>> video-interfaces.yaml
>>>
>>> Two competing values are redundant and it opens a door to a wrong
>>> hardware description, the technical discussion has not been started yet.
>> So as I said before, I'm following Rob Herring's input on this and
>> Krzysztof has given RB for this binding. At this stage, I don't see
>> scope to change it.
>>
>> Adding endpoints was already a compromise to address your feedback,
>> which I hoped would bring you on board with the design.
> That's my comment dated March 27, 2026, and it says moving phy type
> from phy cell to the endpoint property excludes the need to set any
> phy cells:
> 
> https://lore.kernel.org/linux-arm-msm/e37ce438-12c7-462d- 
> b2bc-1351be62b806@linaro.org/
> 
> The technical comment is left unresponded so far since then.
> 
> Since there is no expected phy cells to get on consumer's side, and
> since there is another link between CSIPHY and CSID described in
> video-interfaces.yaml, any kind of dependency of this IP on phy can
> be just removed, which serves the purpose of hardware description
> simplification.

Rob's v1 feedback was consumer-decides-mode via the cell; Krzysztof has
R-b'd the binding with cells=1.

I'm happy to lock down this binding as-is on that basis.

Are you arguing about phy-cells or are you actually arguing the entire
instantiation of Qualcomm MIPI CSI2 as a standalone generic driver in 
drivers/phy ? Its not the same debate at all.

As the CAMSS maintainer, I'm fully against adding more inline monolithic 
CSIPHY init sequences. That could be represented as a separate 
linux-media driver but, then that implies that _all_ upstream CSIPHY 
drivers in drivers/phy are wrong, and I just don't accept that.

The bindings have DT maintainer RB, and the driver has Qcom engineer 
tested-by, review-by.

Vinod, Kishon - Again, I'd request this merges as-is.

---
bod

  reply	other threads:[~2026-07-21 10:47 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-07-20  1:11 [PATCH v13 0/2] phy: qcom-mipi-csi2: Add a CSI2 MIPI DPHY driver Bryan O'Donoghue
2026-07-20  1:11 ` [PATCH v13 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema Bryan O'Donoghue
2026-07-20  1:20   ` sashiko-bot
2026-07-21  8:15   ` Neil Armstrong
2026-07-21  8:17   ` Vladimir Zapolskiy
2026-07-21  9:39     ` Bryan O'Donoghue
2026-07-21  9:56       ` Vladimir Zapolskiy
2026-07-21 10:47         ` Bryan O'Donoghue [this message]
2026-07-21 11:05           ` Vladimir Zapolskiy
2026-07-21 11:24             ` Bryan O'Donoghue
2026-07-21 13:19               ` Bryan O'Donoghue
2026-07-21 13:35                 ` Vladimir Zapolskiy
2026-07-21 14:06                   ` Bryan O'Donoghue
2026-07-21 19:24                   ` Bryan O'Donoghue
2026-07-21 18:57   ` Frank Li
2026-07-20  1:11 ` [PATCH v13 2/2] phy: qcom-mipi-csi2: Add a CSI2 MIPI DPHY driver Bryan O'Donoghue
2026-07-20  1:26   ` sashiko-bot
2026-07-20  3:23   ` Wenmeng Liu
2026-07-20  8:21   ` Loic Poulain
2026-07-21 11:30   ` Vladimir Zapolskiy

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=c236cf94-a775-4158-88db-9a337c7fa862@kernel.org \
    --to=bod@kernel.org \
    --cc=bryan.odonoghue@linaro.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kishon@kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=krzysztof.kozlowski@oss.qualcomm.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=neil.armstrong@linaro.org \
    --cc=robh@kernel.org \
    --cc=vkoul@kernel.org \
    --cc=vladimir.zapolskiy@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox