From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: "Bernhard Rosenkränzer" <bero@baylibre.com>,
linux-mediatek@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
matthias.bgg@gmail.com
Subject: Re: [PATCH] arm64: dts: mediatek: Initial mt8365-evk support
Date: Tue, 8 Nov 2022 11:02:28 +0100 [thread overview]
Message-ID: <c2535843-f05e-256a-65dc-59b2325f247b@linaro.org> (raw)
In-Reply-To: <20221107211001.257393-1-bero@baylibre.com>
On 07/11/2022 22:10, Bernhard Rosenkränzer wrote:
> From: Fabien Parent <fparent@baylibre.com>
>
> This adds minimal support for the MediaTek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
>
> GPIO keys are supported, MMC is partially supported (needs the clocks
> driver for full support).
>
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> ---
>
> Compared to the previous version of the patch submitted by Fabien
> Parent, this removes dependencies on drivers/patches that are not yet in
> mainline (obviously this comes with some reduced functionality for now;
> this will be added back as drivers are accepted), and addresses some
> feedback from reviewers.
>
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 344 +++++++++++
> arch/arm64/boot/dts/mediatek/mt8365.dtsi | 602 ++++++++++++++++++++
> 3 files changed, 947 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 0ec90cb3ef289..e668fd50a3326 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -46,4 +46,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> new file mode 100644
> index 0000000000000..a24e478fff51f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> @@ -0,0 +1,344 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2021-2022 BayLibre, SAS.
> + * Authors:
> + * Fabien Parent <fparent@baylibre.com>
> + * Bernhard Rosenkränzer <bero@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
> +#include "mt8365.dtsi"
> +
> +/ {
> + model = "MediaTek MT8365 Open Platform EVK";
> + compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
Missing documentation.
Run checkpatch on your patches. It will print several warnings, which
must be fixed.
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +
> + firmware {
> + optee {
> + compatible = "linaro,optee-tz";
> + method = "smc";
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + input-name = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_keys>;
> +
> + key-volume-up {
> + gpios = <&pio 24 GPIO_ACTIVE_LOW>;
> + label = "volume_up";
> + linux,code = <KEY_VOLUMEUP>;
> + wakeup-source;
> + debounce-interval = <15>;
> + };
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0xc0000000>;
> + };
> +
> + usb_otg_vbus: regulator-2 {
Where are regulators 0 and 1 (or just 1)?
> + compatible = "regulator-fixed";
> + regulator-name = "otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
(...)
> +
> + mcucfg: syscon@10200000 {
> + compatible = "mediatek,mt8365-mcucfg", "syscon";
> + reg = <0 0x10200000 0 0x2000>;
> + #clock-cells = <1>;
> + };
> +
> + sysirq: interrupt-controller@10200a80 {
> + compatible = "mediatek,mt8365-sysirq",
> + "mediatek,mt6577-sysirq";
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + reg = <0 0x10200a80 0 0x20>;
> + };
> +
> + infracfg_nao: infracfg-nao@1020e000 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "syscon";
Not allowed on its own.
> + reg = <0 0x1020e000 0 0x1000>;
> + };
> +
> + rng: rng@1020f000 {
> + compatible = "mediatek,mt8365-rng",
> + "mediatek,mt7623-rng";
> + reg = <0 0x1020f000 0 0x100>;
> + clocks = <&infracfg CLK_IFR_TRNG>;
> + clock-names = "rng";
> + };
> +
> + apdma: dma-controller@11000280 {
> + compatible = "mediatek,mt8365-uart-dma",
> + "mediatek,mt6577-uart-dma";
> + reg = <0 0x11000280 0 0x80>,
> + <0 0x11000300 0 0x80>,
> + <0 0x11000380 0 0x80>,
> + <0 0x11000400 0 0x80>,
> + <0 0x11000580 0 0x80>,
> + <0 0x11000600 0 0x80>;
> + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
> + dma-requests = <6>;
> + clocks = <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "apdma";
> + #dma-cells = <1>;
> + };
> +
> + auxadc: adc@11001000 {
> + compatible = "mediatek,mt8365-auxadc",
> + "mediatek,mt8173-auxadc";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&infracfg CLK_IFR_AUXADC>;
> + clock-names = "main";
> + #io-channel-cells = <1>;
> + };
> +
> + uart0: serial@11002000 {
> + compatible = "mediatek,mt8365-uart",
> + "mediatek,mt6577-uart";
> + reg = <0 0x11002000 0 0x1000>;
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 0>, <&apdma 1>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + uart1: serial@11003000 {
> + compatible = "mediatek,mt8365-uart",
> + "mediatek,mt6577-uart";
> + reg = <0 0x11003000 0 0x1000>;
> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 2>, <&apdma 3>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + uart2: serial@11004000 {
> + compatible = "mediatek,mt8365-uart",
> + "mediatek,mt6577-uart";
> + reg = <0 0x11004000 0 0x1000>;
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 4>, <&apdma 5>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + pwm: pwm@11006000 {
> + compatible = "mediatek,mt8365-pwm";
> + reg = <0 0x11006000 0 0x1000>;
> + #pwm-cells = <2>;
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_IFR_PWM_HCLK>,
> + <&infracfg CLK_IFR_PWM>,
> + <&infracfg CLK_IFR_PWM1>,
> + <&infracfg CLK_IFR_PWM2>,
> + <&infracfg CLK_IFR_PWM3>;
> + clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
> + };
> +
> + i2c0: i2c@11007000 {
> + compatible = "mediatek,mt8365-i2c",
> + "mediatek,mt8168-i2c";
> + reg = <0 0x11007000 0 0xa0>,
> + <0 0x11000080 0 0x80>;
> + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <1>;
> + clocks = <&infracfg CLK_IFR_I2C0_AXI>,
> + <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "main", "dma";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c@11008000 {
> + compatible = "mediatek,mt8365-i2c",
> + "mediatek,mt8168-i2c";
> + reg = <0 0x11008000 0 0xa0>,
> + <0 0x11000100 0 0x80>;
> + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <1>;
> + clocks = <&infracfg CLK_IFR_I2C1_AXI>,
> + <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "main", "dma";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@11009000 {
> + compatible = "mediatek,mt8365-i2c",
> + "mediatek,mt8168-i2c";
> + reg = <0 0x11009000 0 0xa0>,
> + <0 0x11000180 0 0x80>;
> + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <1>;
> + clocks = <&infracfg CLK_IFR_I2C2_AXI>,
> + <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "main", "dma";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi: spi@1100a000 {
> + compatible = "mediatek,mt8365-spi",
> + "mediatek,mt7622-spi";
> + reg = <0 0x1100a000 0 0x100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
> + <&topckgen CLK_TOP_SPI_SEL>,
> + <&infracfg CLK_IFR_SPI0>;
> + clock-names = "parent-clk", "sel-clk", "spi-clk";
> + status = "disabled";
> + };
> +
> + thermal: thermal@1100b000 {
> + compatible = "mediatek,mt8365-thermal";
> + reg = <0 0x1100b000 0 0x1000>;
> + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_IFR_THERM>,
> + <&infracfg CLK_IFR_AUXADC>;
> + clock-names = "therm", "auxadc";
> + mediatek,auxadc = <&auxadc>;
> + mediatek,apmixedsys = <&apmixedsys>;
> + nvmem-cells = <&thermal_calibration>;
> + nvmem-cell-names = "calibration-data";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + i2c3: i2c@1100f000 {
> + compatible = "mediatek,mt8365-i2c",
> + "mediatek,mt8168-i2c";
> + reg = <0 0x1100f000 0 0xa0>,
> + <0 0x11000200 0 0x80>;
> + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <1>;
> + clocks = <&infracfg CLK_IFR_I2C3_AXI>,
> + <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "main", "dma";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + ssusb: usb@11201000 {
> + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
> + reg = <0 0x11201000 0 0x2e00>,
> + <0 0x11203e00 0 0x0100>;
> + reg-names = "mac", "ippc";
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
> + phys = <&u2port0 PHY_TYPE_USB2>,
> + <&u2port1 PHY_TYPE_USB2>;
> + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> + <&infracfg CLK_IFR_SSUSB_REF>,
> + <&infracfg CLK_IFR_SSUSB_SYS>,
> + <&infracfg CLK_IFR_ICUSB>;
> + clock-names = "sys_ck", "ref_ck", "mcu_ck",
> + "dma_ck";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + status = "disabled";
> +
> + usb_host: usb@11200000 {
> + compatible = "mediatek,mt8365-xhci",
> + "mediatek,mtk-xhci";
> + reg = <0 0x11200000 0 0x1000>;
> + reg-names = "mac";
> + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> + <&infracfg CLK_IFR_SSUSB_REF>,
> + <&infracfg CLK_IFR_SSUSB_SYS>,
> + <&infracfg CLK_IFR_ICUSB>,
> + <&infracfg CLK_IFR_SSUSB_XHCI>;
> + clock-names = "sys_ck", "ref_ck", "mcu_ck",
> + "dma_ck", "xhci_ck";
> + status = "disabled";
> + };
> + };
> +
> + mmc0: mmc@11230000 {
> + compatible = "mediatek,mt8365-mmc", "mediatek,mt8183-mmc";
> + reg = <0 0x11230000 0 0x1000>,
> + <0 0x11cd0000 0 0x1000>;
> + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>,
> + <&infracfg CLK_IFR_MSDC0_HCLK>,
> + <&infracfg CLK_IFR_MSDC0_SRC>;
> + clock-names = "source", "hclk", "source_cg";
> + status = "disabled";
> + };
> +
> + mmc1: mmc@11240000 {
> + compatible = "mediatek,mt8365-mmc", "mediatek,mt8183-mmc";
> + reg = <0 0x11240000 0 0x1000>,
> + <0 0x11c90000 0 0x1000>;
> + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>,
> + <&infracfg CLK_IFR_MSDC1_HCLK>,
> + <&infracfg CLK_IFR_MSDC1_SRC>;
> + clock-names = "source", "hclk", "source_cg";
> + status = "disabled";
> + };
> +
> + ethernet: ethernet@112a0000 {
> + compatible = "mediatek,mt8365-eth";
> + reg = <0 0x112a0000 0 0x1000>;
> + mediatek,pericfg = <&infracfg>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&topckgen CLK_TOP_ETH_SEL>,
> + <&infracfg CLK_IFR_NIC_AXI>,
> + <&infracfg CLK_IFR_NIC_SLV_AXI>;
> + clock-names = "core", "reg", "trans";
> + status = "disabled";
> + };
> +
> + mipi_tx0: dsi-phy@11c00000 {
> + compatible = "mediatek,mt8365-mipi-tx",
> + "mediatek,mt8183-mipi-tx";
> + reg = <0 0x11c00000 0 0x800>;
> + clocks = <&clk26m>;
> + clock-names = "ref_clk";
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> + clock-output-names = "mipi_tx0_pll";
> + };
> +
> + efuse: efuse@11c50000 {
> + compatible = "mediatek,mt8365-efuse", "mediatek,efuse";
> + reg = <0 0x11c50000 0 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + thermal_calibration: calib@180 {
> + reg = <0x180 0xc>;
> + };
> + };
> +
> + u3phy: t-phy@11cc0000 {
Node names should be generic, so just phy
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "mediatek,mt8365-tphy",
> + "mediatek,generic-tphy-v2";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + #phy-cells = <1>;
> + ranges;
> +
> + u2port0: usb-phy@11cc0000 {
> + reg = <0 0x11cc0000 0 0x400>;
> + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> + <&topckgen CLK_TOP_USB20_48M_EN>;
> + clock-names = "ref", "da_ref";
> + #phy-cells = <1>;
> + };
> +
> + u2port1: usb-phy@11cc1000 {
> + reg = <0 0x11cc1000 0 0x400>;
> + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> + <&topckgen CLK_TOP_USB20_48M_EN>;
> + clock-names = "ref", "da_ref";
> + #phy-cells = <1>;
> + };
> + };
> +
> + mfgcfg: syscon@13000000 {
> + compatible = "mediatek,mt8365-mfgcfg", "syscon";
> + reg = <0 0x13000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + mmsys: syscon@14000000 {
> + compatible = "mediatek,mt8365-mmsys", "syscon";
> + reg = <0 0x14000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + camsys: syscon@15000000 {
> + compatible = "mediatek,mt8365-imgsys", "syscon";
> + reg = <0 0x15000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys: syscon@16000000 {
> + compatible = "mediatek,mt8365-vdecsys", "syscon";
> + reg = <0 0x16000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vencsys: syscon@17000000 {
> + compatible = "mediatek,mt8365-vencsys", "syscon";
> + reg = <0 0x17000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + apu: syscon@19020000 {
> + compatible = "mediatek,mt8365-apu", "syscon";
> + reg = <0 0x19020000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay-passive = <1000>; /* milliseconds */
> + polling-delay = <1000>; /* milliseconds */
> + thermal-sensors = <&thermal 0>;
> +
> + trips {
> + threshold: trip-point0 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + target: trip-point1 {
> + temperature = <105000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu_crit: cpu_crit0 {
> + temperature = <117000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&target>;
> + cooling-device =
> + <&cpu0
> + THERMAL_NO_LIMIT
> + THERMAL_NO_LIMIT>,
> + <&cpu1
> + THERMAL_NO_LIMIT
> + THERMAL_NO_LIMIT>,
> + <&cpu2
> + THERMAL_NO_LIMIT
> + THERMAL_NO_LIMIT>,
> + <&cpu3
> + THERMAL_NO_LIMIT
> + THERMAL_NO_LIMIT>;
> + contribution = <100>;
> + };
> + };
> + };
> + };
> +
> +
Only one blank line.
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
> + };
> +};
Best regards,
Krzysztof
next prev parent reply other threads:[~2022-11-08 10:03 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-07 21:10 [PATCH] arm64: dts: mediatek: Initial mt8365-evk support Bernhard Rosenkränzer
2022-11-08 10:02 ` Krzysztof Kozlowski [this message]
2022-11-15 2:54 ` [PATCH v2 00/15] Initial Mediatek MT8365 SOC and MT8365-EVK board support Bernhard Rosenkränzer
2022-11-15 2:54 ` [PATCH v2 01/15] arm64: dts: mediatek: Initial mt8365-evk support Bernhard Rosenkränzer
2022-11-15 9:23 ` AngeloGioacchino Del Regno
2022-11-15 9:41 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 02/15] dt-bindings: watchdog: mtk-wdt: Add MT8365 SoC bindings Bernhard Rosenkränzer
2022-11-15 9:01 ` AngeloGioacchino Del Regno
2022-11-15 9:42 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 03/15] dt-bindings: iio: adc: mediatek: add " Bernhard Rosenkränzer
2022-11-15 9:02 ` AngeloGioacchino Del Regno
2022-11-15 9:42 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 04/15] dt-bindings: i2c: i2c-mt65xx: add binding for MT8365 SoC Bernhard Rosenkränzer
2022-11-15 2:54 ` [PATCH v2 05/15] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings Bernhard Rosenkränzer
2022-11-15 9:43 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 06/15] dt-bindings: usb: mediatek,mtk-xhci: " Bernhard Rosenkränzer
2022-11-15 9:44 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 07/15] dt-bindings: mmc: mtk-sd: add bindings for MT8365 SoC Bernhard Rosenkränzer
2022-11-15 9:44 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 08/15] dt-bindings: nvmem: mediatek,efuse: add MT8365 bindings Bernhard Rosenkränzer
2022-11-15 9:45 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 09/15] dt-bindings: mfd: syscon: Add mt8365-syscfg Bernhard Rosenkränzer
2022-11-15 9:45 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 10/15] dt-bindings: timer: Add compatible for Mediatek MT8365 Bernhard Rosenkränzer
2022-11-15 9:46 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 11/15] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC Bernhard Rosenkränzer
2022-11-15 9:46 ` Krzysztof Kozlowski
2022-11-15 14:11 ` Rob Herring
2022-11-15 2:54 ` [PATCH v2 12/15] dt-bindings: soc: mediatek: pwrap: add compatible for mt8365 Bernhard Rosenkränzer
2022-11-15 9:46 ` Krzysztof Kozlowski
2022-11-15 2:54 ` [PATCH v2 13/15] dt-bindings: irq: mtk, sysirq: add support " Bernhard Rosenkränzer
2022-11-15 2:54 ` [PATCH v2 14/15] dt-bindings: thermal: mediatek: add documentation for MT8365 SoC Bernhard Rosenkränzer
2022-11-15 2:54 ` [PATCH v2 15/15] dt-bindings: arm64: dts: mediatek: Add mt8365-evk board Bernhard Rosenkränzer
2022-11-15 9:47 ` Krzysztof Kozlowski
2022-11-15 13:50 ` [PATCH v2 00/15] Initial Mediatek MT8365 SOC and MT8365-EVK board support Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c2535843-f05e-256a-65dc-59b2325f247b@linaro.org \
--to=krzysztof.kozlowski@linaro.org \
--cc=bero@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).