Re: [PATCH v9 2/9] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Ravi Gunasekaran <r-gunasekaran@ti.com>]

On 20/02/23 8:15 pm, Andrew Davis wrote:
> On 2/20/23 5:14 AM, Ravi Gunasekaran wrote:
>> From: Aswath Govindraju <a-govindraju@ti.com>
>>
>> Add support for single instance of USB 3.0 controller in J721S2 SoC.
>>
>> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
>> Signed-off-by: Matt Ranostay <mranostay@ti.com>
>> Link: https://lore.kernel.org/r/20221122101616.770050-2-mranostay@ti.com
>> Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
>> ---
>> I had reviewed this patch in the v5 series [1].
>> Since I'm taking over upstreaming this series, I removed the self
>> Reviewed-by tag.
>>
>> Links:
>>
>> [1] - https://lore.kernel.org/all/134c28a0-2d49-549c-dc8d-0887d8fd29c3@ti.com/
>>
>>   arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
>>   1 file changed, 42 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
>> index 8915132efcc1..c0daa75116f9 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
>> @@ -26,6 +26,20 @@
>>           };
>>       };
>>   +    scm_conf: syscon@104000 {
>> +        compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
>> +        reg = <0x00 0x00104000 0x00 0x18000>;
>> +        #address-cells = <1>;
>> +        #size-cells = <1>;
>> +        ranges = <0x00 0x00 0x00104000 0x18000>;
>> +
>> +        usb_serdes_mux: mux-controller@0 {
>> +            compatible = "mmio-mux";
>> +            #mux-control-cells = <1>;
>> +            mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
>> +        };
>> +    };
>> +
>>       gic500: interrupt-controller@1800000 {
>>           compatible = "arm,gic-v3";
>>           #address-cells = <2>;
>> @@ -745,6 +759,34 @@
>>           };
>>       };
>>   +    usbss0: cdns-usb@4104000 {
> 
> Since this cannot be used without additional pinmux information in the
> board level dtb files, this can be set disabled in this include file. Then
> set back to "okay" where you add the pinmux. Same for the OSPI and PCIe patches.
> 
> Andrew

Sure. I will do so and post the next series.

Ravi

> 
>> +        compatible = "ti,j721e-usb";
>> +        reg = <0x00 0x04104000 0x00 0x100>;
>> +        clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
>> +        clock-names = "ref", "lpm";
>> +        assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
>> +        assigned-clock-parents = <&k3_clks 360 17>;
>> +        power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
>> +        #address-cells = <2>;
>> +        #size-cells = <2>;
>> +        ranges;
>> +        dma-coherent;
>> +
>> +        usb0: usb@6000000 {
>> +            compatible = "cdns,usb3";
>> +            reg = <0x00 0x06000000 0x00 0x10000>,
>> +                  <0x00 0x06010000 0x00 0x10000>,
>> +                  <0x00 0x06020000 0x00 0x10000>;
>> +            reg-names = "otg", "xhci", "dev";
>> +            interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
>> +                     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
>> +                     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
>> +            interrupt-names = "host", "peripheral", "otg";
>> +            maximum-speed = "super-speed";
>> +            dr_mode = "otg";
>> +        };
>> +    };
>> +
>>       main_mcan0: can@2701000 {
>>           compatible = "bosch,m_can";
>>           reg = <0x00 0x02701000 0x00 0x200>,