[PATCH 1/3] ARM: dts: socfpga: Add QSPI node for the Arria10

[PATCH 1/3] ARM: dts: socfpga: Add QSPI node for the Arria10

[dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx]

From: Dinh Nguyen <dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>

Add the QSPI device node for Arria10 SOC.

Signed-off-by: Dinh Nguyen <dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>
---
 arch/arm/boot/dts/socfpga_arria10.dtsi |   14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/socfpga_arria10.dtsi
index 1149216..551c636 100644
--- a/arch/arm/boot/dts/socfpga_arria10.dtsi
+++ b/arch/arm/boot/dts/socfpga_arria10.dtsi
@@ -675,6 +675,20 @@
 			};
 		};
 
+		qspi: spi@ff809000 {
+			compatible = "cdns,qspi-nor";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xff809000 0x100>,
+			      <0xffa00000 0x100000>;
+			interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <128>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x00000000>;
+			clocks = <&qspi_clk>;
+			status = "disabled";
+		};
+
 		rst: rstmgr@ffd05000 {
 			#reset-cells = <1>;
 			compatible = "altr,rst-mgr";
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] ARM: dts: socfpga: Enable QSPI in Arria10 devkit

[dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx]

From: Dinh Nguyen <dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>

Enable the QSPI node and add the flash chip.

Signed-off-by: Dinh Nguyen <dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                       |    1 +
 arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts |   49 ++++++++++++++++++++++
 2 files changed, 50 insertions(+)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c5f0c3..081fd94 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -690,6 +690,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	sh73a0-kzm9g.dtb
 dtb-$(CONFIG_ARCH_SOCFPGA) += \
 	socfpga_arria5_socdk.dtb \
+	socfpga_arria10_socdk_qspi.dtb \
 	socfpga_arria10_socdk_sdmmc.dtb \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts b/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
new file mode 100644
index 0000000..beb2fc6
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
@@ -0,0 +1,49 @@
+/*
+ * Copyright (C) 2016 Intel. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/dts-v1/;
+#include "socfpga_arria10_socdk.dtsi"
+
+&qspi {
+	status = "okay";
+
+	flash0: n25q00@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "n25q00aa";
+		reg = <0>;
+		spi-max-frequency = <100000000>;
+
+		m25p,fast-read;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		cdns,read-delay = <4>;
+		cdns,tshsl-ns = <50>;
+		cdns,tsd2d-ns = <50>;
+		cdns,tchsh-ns = <4>;
+		cdns,tslch-ns = <4>;
+
+		partition@qspi-boot {
+			label = "Boot and fpga data";
+			reg = <0x0 0x2720000>;
+		};
+
+		partition@qspi-rootfs {
+			label = "Root Filesystem - JFFS2";
+			reg = <0x2720000 0x58E0000>;
+		};
+	};
+};
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 3/3] ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit

[dinguyen]

From: Dinh Nguyen <dinguyen@opensource.altera.com>

Enable the QSPI node and add the flash chip.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
 arch/arm/boot/dts/socfpga_cyclone5_sockit.dts |   33 +++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
index 02e22f5..2f75e0f 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
@@ -175,6 +175,39 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "n25q256a";
+		reg = <0>;
+		spi-max-frequency = <100000000>;
+
+		m25p,fast-read;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		cdns,read-delay = <4>;
+		cdns,tshsl-ns = <50>;
+		cdns,tsd2d-ns = <50>;
+		cdns,tchsh-ns = <4>;
+		cdns,tslch-ns = <4>;
+
+		partition@qspi-boot {
+			/* 8MB for raw data. */
+			label = "Flash 0 Raw Data";
+			reg = <0x0 0x800000>;
+		};
+
+		partition@qspi-rootfs {
+			/* 120MB for jffs2 data. */
+			label = "Flash 0 jffs2 Filesystem";
+			reg = <0x800000 0x7800000>;
+		};
+	};
+};
+
 &usb1 {
 	status = "okay";
 };
-- 
1.7.9.5

Re: [PATCH 3/3] ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit

[Steffen Trumtrar]

Hi!

On Wed, Oct 19, 2016 at 03:18:44PM -0500, dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org wrote:
> From: Dinh Nguyen <dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>
> 
> Enable the QSPI node and add the flash chip.
> 
> Signed-off-by: Dinh Nguyen <dinguyen-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>
> ---
>  arch/arm/boot/dts/socfpga_cyclone5_sockit.dts |   33 +++++++++++++++++++++++++
>  1 file changed, 33 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
> index 02e22f5..2f75e0f 100644
> --- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
> +++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
> @@ -175,6 +175,39 @@
>  	status = "okay";
>  };
>  
> +&qspi {
> +	status = "okay";
> +
> +	flash: flash@0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "n25q256a";
> +		reg = <0>;
> +		spi-max-frequency = <100000000>;
> +
> +		m25p,fast-read;
> +		cdns,page-size = <256>;
> +		cdns,block-size = <16>;
> +		cdns,read-delay = <4>;
> +		cdns,tshsl-ns = <50>;
> +		cdns,tsd2d-ns = <50>;
> +		cdns,tchsh-ns = <4>;
> +		cdns,tslch-ns = <4>;
> +
> +		partition@qspi-boot {
> +			/* 8MB for raw data. */
> +			label = "Flash 0 Raw Data";
> +			reg = <0x0 0x800000>;
> +		};
> +
> +		partition@qspi-rootfs {
> +			/* 120MB for jffs2 data. */
> +			label = "Flash 0 jffs2 Filesystem";
> +			reg = <0x800000 0x7800000>;
> +		};
> +	};
> +};
> +

What is the current preferred way of handling the partitions?
This doesn't fit my Sockit configuration for example. So I would always
have to patch the devicetree.

On the Socrates I didn't specify the partitions, because I did not
want to force a specific configuration.

Regards,
Steffen

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 3/3] ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit

[Dinh Nguyen]

On 10/20/2016 02:19 AM, Steffen Trumtrar wrote:

>> +		cdns,tslch-ns = <4>;
>> +
>> +		partition@qspi-boot {
>> +			/* 8MB for raw data. */
>> +			label = "Flash 0 Raw Data";
>> +			reg = <0x0 0x800000>;
>> +		};
>> +
>> +		partition@qspi-rootfs {
>> +			/* 120MB for jffs2 data. */
>> +			label = "Flash 0 jffs2 Filesystem";
>> +			reg = <0x800000 0x7800000>;
>> +		};
>> +	};
>> +};
>> +
> 
> What is the current preferred way of handling the partitions?
> This doesn't fit my Sockit configuration for example. So I would always
> have to patch the devicetree.

I'm not 100% sure on this. Graham, do you have any insight?
> 
> On the Socrates I didn't specify the partitions, because I did not
> want to force a specific configuration.
> 

I know that on Arria10, we needed a specific configuration.

Dinh

Re: [PATCH 3/3] ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit

[Graham Moore]

On 10/20/2016 09:12 AM, Dinh Nguyen wrote:
>
>
> On 10/20/2016 02:19 AM, Steffen Trumtrar wrote:
>
>>> +		cdns,tslch-ns = <4>;
>>> +
>>> +		partition@qspi-boot {
>>> +			/* 8MB for raw data. */
>>> +			label = "Flash 0 Raw Data";
>>> +			reg = <0x0 0x800000>;
>>> +		};
>>> +
>>> +		partition@qspi-rootfs {
>>> +			/* 120MB for jffs2 data. */
>>> +			label = "Flash 0 jffs2 Filesystem";
>>> +			reg = <0x800000 0x7800000>;
>>> +		};
>>> +	};
>>> +};
>>> +
>>
>> What is the current preferred way of handling the partitions?
>> This doesn't fit my Sockit configuration for example. So I would always
>> have to patch the devicetree.
>
> I'm not 100% sure on this. Graham, do you have any insight?
>>

Well, strictly speaking, these partitions are only for the socdk, the 
Altera dev kit.  Our sample designs and file systems expect this layout.

Therefore, these partitions are not required for any other dev kits, and 
can probably be left out.

Or, Steffen, if you have a standard layout you'd like to see, then put 
that in there.

I think some people will have to patch the layout regardless.

-Graham

Re: [PATCH 3/3] ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit

[Dinh Nguyen]

On 10/25/2016 10:38 AM, Graham Moore wrote:
> On 10/20/2016 09:12 AM, Dinh Nguyen wrote:
>>
>>
>> On 10/20/2016 02:19 AM, Steffen Trumtrar wrote:
>>
>>>> +        cdns,tslch-ns = <4>;
>>>> +
>>>> +        partition@qspi-boot {
>>>> +            /* 8MB for raw data. */
>>>> +            label = "Flash 0 Raw Data";
>>>> +            reg = <0x0 0x800000>;
>>>> +        };
>>>> +
>>>> +        partition@qspi-rootfs {
>>>> +            /* 120MB for jffs2 data. */
>>>> +            label = "Flash 0 jffs2 Filesystem";
>>>> +            reg = <0x800000 0x7800000>;
>>>> +        };
>>>> +    };
>>>> +};
>>>> +
>>>
>>> What is the current preferred way of handling the partitions?
>>> This doesn't fit my Sockit configuration for example. So I would always
>>> have to patch the devicetree.
>>
>> I'm not 100% sure on this. Graham, do you have any insight?
>>>
> 
> Well, strictly speaking, these partitions are only for the socdk, the
> Altera dev kit.  Our sample designs and file systems expect this layout.
> 
> Therefore, these partitions are not required for any other dev kits, and
> can probably be left out.
> 
> Or, Steffen, if you have a standard layout you'd like to see, then put
> that in there.
> 
> I think some people will have to patch the layout regardless.
> 

Ok, I'll remove the partitions from the none Altera boards.

Dinh

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 3/3] ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit

[Steffen Trumtrar]

Hi!

On Tue, Oct 25, 2016 at 10:38:10AM -0500, Graham Moore wrote:
> On 10/20/2016 09:12 AM, Dinh Nguyen wrote:
> > 
> > 
> > On 10/20/2016 02:19 AM, Steffen Trumtrar wrote:
> > 
> > > > +		cdns,tslch-ns = <4>;
> > > > +
> > > > +		partition@qspi-boot {
> > > > +			/* 8MB for raw data. */
> > > > +			label = "Flash 0 Raw Data";
> > > > +			reg = <0x0 0x800000>;
> > > > +		};
> > > > +
> > > > +		partition@qspi-rootfs {
> > > > +			/* 120MB for jffs2 data. */
> > > > +			label = "Flash 0 jffs2 Filesystem";
> > > > +			reg = <0x800000 0x7800000>;
> > > > +		};
> > > > +	};
> > > > +};
> > > > +
> > > 
> > > What is the current preferred way of handling the partitions?
> > > This doesn't fit my Sockit configuration for example. So I would always
> > > have to patch the devicetree.
> > 
> > I'm not 100% sure on this. Graham, do you have any insight?
> > > 
> 
> Well, strictly speaking, these partitions are only for the socdk, the Altera
> dev kit.  Our sample designs and file systems expect this layout.

The thing is, that I don't think these partitions belong in a mainline
dts at all. But I'm not sure what the current policy is.

> 
> Therefore, these partitions are not required for any other dev kits, and can
> probably be left out.
> 
> Or, Steffen, if you have a standard layout you'd like to see, then put that
> in there.
> 

Well in my case, it actually doesn't really matter. All the boards
I use do not have u-boot as bootloader but barebox. And barebox uses
devicetree fixups for adding the partition layout that fits the
particular use case. All other partitions are thrown out.
I don't know if u-boot does something like this.

Regards,
Steffen

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html