[PATCH V6 0/4] Add PCIe support for IPQ9574

[PATCH V6 0/4] Add PCIe support for IPQ9574

[Sricharan R]

From: Sricharan Ramabadhran <quic_srichara@quicinc.com>

This series adds support for enabling the PCIe host devices (PCIe0, PCIe1,
PCIe2, PCIe3) found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host and PCIe2 & PCIe3 are 2-lane Gen3 host.

[V6]
        - Dropped patches [1] and [2] for clks, since its already merged.
        - Addressed all comments from Krzysztof, Manivannan, Bjorn Helgaas.
          Specifically dropped defining a new macro for SLV_ADDR_SPACE_SZ.
          Letting it at reset value is fine.

          Both dt_binding_check and dtbs_check passed and tested on ipq9574-rdp433

	[1] - https://patchwork.kernel.org/project/linux-pci/patch/20240512082858.1806694-2-quic_devipriy@quicinc.com/
	[2] - https://patchwork.kernel.org/project/linux-pci/patch/20240512082858.1806694-3-quic_devipriy@quicinc.com/

[V5]
	Change logs are added to the respective patches
	This series depends on the below series which adds support for
	Interconnect driver[1] and fetching clocks from the Device Tree[2]
	[1] - https://lore.kernel.org/linux-arm-msm/20240430064214.2030013-1-quic_varada@quicinc.com/
	[2] - https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org/
[V4]
https://lore.kernel.org/linux-arm-msm/20230528142111.GC2814@thinkpad/

[V3]
https://lore.kernel.org/linux-arm-msm/20230421124938.21974-1-quic_devipriy@quicinc.com/
	- Dropped the phy driver and binding patches as they have been
	  posted as a separate series.
	- Dropped the pinctrl binding fix patch as it is unrelated to the series
	  dt-bindings: pinctrl: qcom: Add few missing functions.
	- Rebased on linux-next/master.
	- Detailed change logs are added to the respective patches.

[V2]
https://lore.kernel.org/linux-arm-msm/20230404164828.8031-1-quic_devipriy@quicinc.com/
	- Reordered the patches and split the board DT changes
	  into a separate patch as suggested
	- Detailed change logs are added to the respective patches
[V1]
https://lore.kernel.org/linux-arm-msm/20230214164135.17039-1-quic_devipriy@quicinc.com/

devi priya (4):
  dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.
  arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes
  arm64: dts: qcom: ipq9574: Enable PCIe PHYs and controllers
  PCI: qcom: Add support for IPQ9574

 .../devicetree/bindings/pci/qcom,pcie.yaml    |  50 +++
 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts   | 113 +++++
 arch/arm64/boot/dts/qcom/ipq9574.dtsi         | 425 +++++++++++++++++-
 drivers/pci/controller/dwc/pcie-qcom.c        |  31 +-
 4 files changed, 611 insertions(+), 8 deletions(-)

--
2.34.1

[PATCH V6 1/4] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Sricharan R]

From: devi priya <quic_devipriy@quicinc.com>

Document the PCIe controller on IPQ9574 platform.

Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
---
 [V6] Fixed the clocks order and dropped unnessecary names as per
      Krzysztof's comments.
      Changed the interrupt numbers/msi to '8'.

 .../devicetree/bindings/pci/qcom,pcie.yaml    | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
index f867746b1ae5..2d61fb9f206d 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
@@ -26,6 +26,7 @@ properties:
           - qcom,pcie-ipq8064-v2
           - qcom,pcie-ipq8074
           - qcom,pcie-ipq8074-gen3
+          - qcom,pcie-ipq9574
           - qcom,pcie-msm8996
           - qcom,pcie-qcs404
           - qcom,pcie-sdm845
@@ -161,6 +162,7 @@ allOf:
             enum:
               - qcom,pcie-ipq6018
               - qcom,pcie-ipq8074-gen3
+              - qcom,pcie-ipq9574
     then:
       properties:
         reg:
@@ -397,6 +399,53 @@ allOf:
             - const: axi_m_sticky # AXI Master Sticky reset
             - const: axi_s_sticky # AXI Slave Sticky reset
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pcie-ipq9574
+    then:
+      properties:
+        clocks:
+          minItems: 6
+          maxItems: 6
+        clock-names:
+          items:
+            - const: axi_m # AXI Master clock
+            - const: axi_s # AXI Slave clock
+            - const: axi_bridge
+            - const: rchng
+            - const: ahb
+            - const: aux
+
+        resets:
+          minItems: 8
+          maxItems: 8
+        reset-names:
+          items:
+            - const: pipe # PIPE reset
+            - const: sticky # Core Sticky reset
+            - const: axi_s_sticky # AXI Slave Sticky reset
+            - const: axi_s # AXI Slave reset
+            - const: axi_m_sticky # AXI Master Sticky reset
+            - const: axi_m # AXI Master reset
+            - const: aux # AUX Reset
+            - const: ahb # AHB Reset
+
+        interrupts:
+          minItems: 8
+        interrupt-names:
+          items:
+            - const: msi0
+            - const: msi1
+            - const: msi2
+            - const: msi3
+            - const: msi4
+            - const: msi5
+            - const: msi6
+            - const: msi7
+
   - if:
       properties:
         compatible:
@@ -507,6 +556,7 @@ allOf:
                 - qcom,pcie-ipq8064v2
                 - qcom,pcie-ipq8074
                 - qcom,pcie-ipq8074-gen3
+                - qcom,pcie-ipq9574
                 - qcom,pcie-qcs404
     then:
       required:
-- 
2.34.1

[PATCH V6 2/4] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Sricharan R]

From: devi priya <quic_devipriy@quicinc.com>

Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.

Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
---
 [V6] Addressed all comments from Manivannan and increased the irq/msi
      to '8'. Fixed the clk's order as per .yaml binding.

 arch/arm64/boot/dts/qcom/ipq9574.dtsi | 425 +++++++++++++++++++++++++-
 1 file changed, 421 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index 48dfafea46a7..f4d4cba0b117 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -226,6 +226,52 @@ rpm_msg_ram: sram@60000 {
 			reg = <0x00060000 0x6000>;
 		};
 
+		pcie0_phy: phy@84000 {
+			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+			reg = <0x00084000 0x1000>;
+
+			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+				 <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_PCIE0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE0_PHY_BCR>,
+				 <&gcc GCC_PCIE0PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie0_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		pcie2_phy: phy@8c000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x0008c000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+				 <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_PCIE2_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE2_PHY_BCR>,
+				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie2_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		rng: rng@e3000 {
 			compatible = "qcom,prng-ee";
 			reg = <0x000e3000 0x1000>;
@@ -243,6 +289,52 @@ mdio: mdio@90000 {
 			status = "disabled";
 		};
 
+		pcie3_phy: phy@f4000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x000f4000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+				 <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_PCIE3_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE3_PHY_BCR>,
+				 <&gcc GCC_PCIE3PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie3_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@fc000 {
+			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+			reg = <0x000fc000 0x1000>;
+
+			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+				 <&gcc GCC_PCIE1_AHB_CLK>,
+				 <&gcc GCC_PCIE1_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE1_PHY_BCR>,
+				 <&gcc GCC_PCIE1PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie1_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		qfprom: efuse@a4000 {
 			compatible = "qcom,ipq9574-qfprom", "qcom,qfprom";
 			reg = <0x000a4000 0x5a1>;
@@ -309,10 +401,10 @@ gcc: clock-controller@1800000 {
 			clocks = <&xo_board_clk>,
 				 <&sleep_clk>,
 				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
+				 <&pcie2_phy>,
+				 <&pcie3_phy>,
 				 <0>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -756,6 +848,331 @@ frame@b128000 {
 				status = "disabled";
 			};
 		};
+
+		pcie1: pcie@10000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x10000000 0xf1d>,
+			       <0x10000f20 0xa8>,
+			       <0x10001000 0x1000>,
+			       <0x000f8000 0x4000>,
+			       <0x10100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <2>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE1_AXI_M_CLK>,
+				 <&gcc GCC_PCIE1_AXI_S_CLK>,
+				 <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE1_RCHNG_CLK>,
+				 <&gcc GCC_PCIE1_AHB_CLK>,
+				 <&gcc GCC_PCIE1_AUX_CLK>;
+			clock-names = "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng",
+				      "ahb",
+				      "aux";
+
+			resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+				 <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_S_ARES>,
+				 <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_M_ARES>,
+				 <&gcc GCC_PCIE1_AUX_ARES>,
+				 <&gcc GCC_PCIE1_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE1 &gcc SLAVE_ANOC_PCIE1>,
+					<&gcc MASTER_SNOC_PCIE1 &gcc SLAVE_SNOC_PCIE1>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
+		pcie3: pcie@18000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x18000000 0xf1d>,
+			       <0x18000f20 0xa8>,
+			       <0x18001000 0x1000>,
+			       <0x000f0000 0x4000>,
+			       <0x18100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <4>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x18200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x18300000 0x18300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 189 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 190 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 191 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE3_AXI_M_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE3_RCHNG_CLK>,
+				 <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_PCIE3_AUX_CLK>;
+			clock-names = "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng",
+				      "ahb",
+				      "aux";
+
+			resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+				 <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_ARES>,
+				 <&gcc GCC_PCIE3_AUX_ARES>,
+				 <&gcc GCC_PCIE3_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie3_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE3 &gcc SLAVE_ANOC_PCIE3>,
+					<&gcc MASTER_SNOC_PCIE3 &gcc SLAVE_SNOC_PCIE3>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
+		pcie2: pcie@20000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x20000000 0xf1d>,
+			       <0x20000f20 0xa8>,
+			       <0x20001000 0x1000>,
+			       <0x00088000 0x4000>,
+			       <0x20100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <3>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x20200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x20300000 0x20300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 164 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 165 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 186 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 187 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE2_AXI_M_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE2_RCHNG_CLK>,
+				 <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_PCIE2_AUX_CLK>;
+			clock-names = "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng",
+				      "ahb",
+				      "aux";
+
+			resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+				 <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_ARES>,
+				 <&gcc GCC_PCIE2_AUX_ARES>,
+				 <&gcc GCC_PCIE2_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie2_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE2 &gcc SLAVE_ANOC_PCIE2>,
+					<&gcc MASTER_SNOC_PCIE2 &gcc SLAVE_SNOC_PCIE2>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
+		pcie0: pci@28000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x28000000 0xf1d>,
+			       <0x28000f20 0xa8>,
+			       <0x28001000 0x1000>,
+			       <0x00080000 0x4000>,
+			       <0x28100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x28200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x28300000 0x28300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE0_AXI_M_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE0_RCHNG_CLK>,
+				 <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_PCIE0_AUX_CLK>;
+			clock-names = "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng",
+				      "ahb",
+				      "aux";
+
+			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_S_ARES>,
+				 <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_M_ARES>,
+				 <&gcc GCC_PCIE0_AUX_ARES>,
+				 <&gcc GCC_PCIE0_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE0 &gcc SLAVE_ANOC_PCIE0>,
+					<&gcc MASTER_SNOC_PCIE0 &gcc SLAVE_SNOC_PCIE0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
 	};
 
 	thermal-zones {
-- 
2.34.1

[PATCH V6 3/4] arm64: dts: qcom: ipq9574: Enable PCIe PHYs and controllers

[Sricharan R]

From: devi priya <quic_devipriy@quicinc.com>

Enable the PCIe controller and PHY nodes corresponding to RDP 433.

Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
---
 [V6] No change.

 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 113 ++++++++++++++++++++
 1 file changed, 113 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 1bb8d96c9a82..f4b6d540612c 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -8,6 +8,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include "ipq9574-rdp-common.dtsi"
 
 / {
@@ -15,6 +16,45 @@ / {
 	compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
 };
 
+&pcie1_phy {
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default>;
+
+	perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcie2_phy {
+	status = "okay";
+};
+
+&pcie2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2_default>;
+
+	perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcie3_phy {
+	status = "okay";
+};
+
+&pcie3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie3_default>;
+
+	perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
 &sdhc_1 {
 	pinctrl-0 = <&sdc_default_state>;
 	pinctrl-names = "default";
@@ -28,6 +68,79 @@ &sdhc_1 {
 };
 
 &tlmm {
+
+	pcie1_default: pcie1-default-state {
+		clkreq-n-pins {
+			pins = "gpio25";
+			function = "pcie1_clk";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio26";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-low;
+		};
+
+		wake-n-pins {
+			pins = "gpio27";
+			function = "pcie1_wake";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	pcie2_default: pcie2-default-state {
+		clkreq-n-pins {
+			pins = "gpio28";
+			function = "pcie2_clk";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio29";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-low;
+		};
+
+		wake-n-pins {
+			pins = "gpio30";
+			function = "pcie2_wake";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	pcie3_default: pcie3-default-state {
+		clkreq-n-pins {
+			pins = "gpio31";
+			function = "pcie3_clk";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+			output-low;
+		};
+
+		wake-n-pins {
+			pins = "gpio33";
+			function = "pcie3_wake";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
 	sdc_default_state: sdc-default-state {
 		clk-pins {
 			pins = "gpio5";
-- 
2.34.1

[PATCH V6 4/4] PCI: qcom: Add support for IPQ9574

[Sricharan R]

From: devi priya <quic_devipriy@quicinc.com>

The IPQ9574 platform has four Gen3 PCIe controllers:
two single-lane and two dual-lane based on SNPS core 5.70a.

QCOM IP rev is 1.27.0 and Synopsys IP rev is 5.80a.
Add a new compatible 'qcom,pcie-ipq9574' and 'ops_1_27_0'
which reuses all the members of 'ops_2_9_0' except for the
post_init as the SLV_ADDR_SPACE_SIZE configuration differs
between 2_9_0 and 1_27_0.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
---
 [V6] Fixed all Manivannan's and Bjorn Helgaas comments.
      Removed the SLV_ADDR_SPACE_SZ_1_27_0 macro to have default value.

 drivers/pci/controller/dwc/pcie-qcom.c | 31 ++++++++++++++++++++++----
 1 file changed, 27 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 0180edf3310e..26acd9f5385e 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -1116,16 +1116,13 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
 	return clk_bulk_prepare_enable(res->num_clks, res->clks);
 }
 
-static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
+static int qcom_pcie_post_init(struct qcom_pcie *pcie)
 {
 	struct dw_pcie *pci = pcie->pci;
 	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
 	u32 val;
 	int i;
 
-	writel(SLV_ADDR_SPACE_SZ,
-		pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
-
 	val = readl(pcie->parf + PARF_PHY_CTRL);
 	val &= ~PHY_TEST_PWR_DOWN;
 	writel(val, pcie->parf + PARF_PHY_CTRL);
@@ -1165,6 +1162,18 @@ static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
 	return 0;
 }
 
+static int qcom_pcie_post_init_1_27_0(struct qcom_pcie *pcie)
+{
+	return qcom_pcie_post_init(pcie);
+}
+
+static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
+{
+	writel(SLV_ADDR_SPACE_SZ, pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
+
+	return qcom_pcie_post_init(pcie);
+}
+
 static int qcom_pcie_link_up(struct dw_pcie *pci)
 {
 	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
@@ -1318,6 +1327,15 @@ static const struct qcom_pcie_ops ops_2_9_0 = {
 	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
 };
 
+/* Qcom IP rev.: 1.27.0  Synopsys IP rev.: 5.80a */
+static const struct qcom_pcie_ops ops_1_27_0 = {
+	.get_resources = qcom_pcie_get_resources_2_9_0,
+	.init = qcom_pcie_init_2_9_0,
+	.post_init = qcom_pcie_post_init_1_27_0,
+	.deinit = qcom_pcie_deinit_2_9_0,
+	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
+};
+
 static const struct qcom_pcie_cfg cfg_1_0_0 = {
 	.ops = &ops_1_0_0,
 };
@@ -1360,6 +1378,10 @@ static const struct qcom_pcie_cfg cfg_sc8280xp = {
 	.no_l0s = true,
 };
 
+static const struct qcom_pcie_cfg cfg_1_27_0 = {
+	.ops = &ops_1_27_0,
+};
+
 static const struct dw_pcie_ops dw_pcie_ops = {
 	.link_up = qcom_pcie_link_up,
 	.start_link = qcom_pcie_start_link,
@@ -1724,6 +1746,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-ipq8064-v2", .data = &cfg_2_1_0 },
 	{ .compatible = "qcom,pcie-ipq8074", .data = &cfg_2_3_3 },
 	{ .compatible = "qcom,pcie-ipq8074-gen3", .data = &cfg_2_9_0 },
+	{ .compatible = "qcom,pcie-ipq9574", .data = &cfg_1_27_0 },
 	{ .compatible = "qcom,pcie-msm8996", .data = &cfg_2_3_2 },
 	{ .compatible = "qcom,pcie-qcs404", .data = &cfg_2_4_0 },
 	{ .compatible = "qcom,pcie-sa8540p", .data = &cfg_sc8280xp },
-- 
2.34.1

Re: [PATCH V6 2/4] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Konrad Dybcio]

On 16.07.2024 11:23 AM, Sricharan R wrote:
> From: devi priya <quic_devipriy@quicinc.com>
> 
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
> 
> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> ---

[...]

> +
> +			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
> +				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */

Drop these comments, please

> +
> +			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +

Inconsistent newline

> +			interrupt-names = "msi0",
> +					  "msi1",
> +					  "msi2",
> +					  "msi3",
> +					  "msi4",
> +					  "msi5",
> +					  "msi6",
> +					  "msi7";
> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc 0 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc 0 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc 0 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

Drop these comments, please

(all these comments apply to all the similar nodes)

[...]

> +
> +		pcie3: pcie@18000000 {
> +			compatible = "qcom,pcie-ipq9574";
> +			reg =  <0x18000000 0xf1d>,
> +			       <0x18000f20 0xa8>,
> +			       <0x18001000 0x1000>,
> +			       <0x000f0000 0x4000>,
> +			       <0x18100000 0x1000>;
> +			reg-names = "dbi", "elbi", "atu", "parf", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <4>;

Any reason the PCI domain for PCIeN is N+1? You can start at 0

Konrad

Re: [PATCH V6 3/4] arm64: dts: qcom: ipq9574: Enable PCIe PHYs and controllers

[Konrad Dybcio]

On 16.07.2024 11:23 AM, Sricharan R wrote:
> From: devi priya <quic_devipriy@quicinc.com>
> 
> Enable the PCIe controller and PHY nodes corresponding to RDP 433.
> 
> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> ---
>  [V6] No change.
> 
>  arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 113 ++++++++++++++++++++
>  1 file changed, 113 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> index 1bb8d96c9a82..f4b6d540612c 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> @@ -8,6 +8,7 @@
>  
>  /dts-v1/;
>  
> +#include <dt-bindings/gpio/gpio.h>
>  #include "ipq9574-rdp-common.dtsi"
>  
>  / {
> @@ -15,6 +16,45 @@ / {
>  	compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
>  };
>  
> +&pcie1_phy {
> +	status = "okay";
> +};
> +
> +&pcie1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie1_default>;

property-n
property-names

please

Konrad

Re: [PATCH V6 1/4] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Krzysztof Kozlowski]

On 16/07/2024 11:23, Sricharan R wrote:
> From: devi priya <quic_devipriy@quicinc.com>
> 
> Document the PCIe controller on IPQ9574 platform.

Subjects are without full stop.

With that fixed:

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH V6 4/4] PCI: qcom: Add support for IPQ9574

[Manivannan Sadhasivam]

On Tue, Jul 16, 2024 at 02:53:47PM +0530, Sricharan R wrote:
> From: devi priya <quic_devipriy@quicinc.com>
> 
> The IPQ9574 platform has four Gen3 PCIe controllers:
> two single-lane and two dual-lane based on SNPS core 5.70a.
> 
> QCOM IP rev is 1.27.0 and Synopsys IP rev is 5.80a.
> Add a new compatible 'qcom,pcie-ipq9574' and 'ops_1_27_0'
> which reuses all the members of 'ops_2_9_0' except for the
> post_init as the SLV_ADDR_SPACE_SIZE configuration differs
> between 2_9_0 and 1_27_0.
> 
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> ---
>  [V6] Fixed all Manivannan's and Bjorn Helgaas comments.
>       Removed the SLV_ADDR_SPACE_SZ_1_27_0 macro to have default value.
> 
>  drivers/pci/controller/dwc/pcie-qcom.c | 31 ++++++++++++++++++++++----
>  1 file changed, 27 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 0180edf3310e..26acd9f5385e 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -1116,16 +1116,13 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
>  	return clk_bulk_prepare_enable(res->num_clks, res->clks);
>  }
>  
> -static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> +static int qcom_pcie_post_init(struct qcom_pcie *pcie)
>  {
>  	struct dw_pcie *pci = pcie->pci;
>  	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>  	u32 val;
>  	int i;
>  
> -	writel(SLV_ADDR_SPACE_SZ,
> -		pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
> -
>  	val = readl(pcie->parf + PARF_PHY_CTRL);
>  	val &= ~PHY_TEST_PWR_DOWN;
>  	writel(val, pcie->parf + PARF_PHY_CTRL);
> @@ -1165,6 +1162,18 @@ static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>  	return 0;
>  }
>  
> +static int qcom_pcie_post_init_1_27_0(struct qcom_pcie *pcie)
> +{
> +	return qcom_pcie_post_init(pcie);
> +}
> +
> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	writel(SLV_ADDR_SPACE_SZ, pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
> +

As discussed in [1], DBI/ATU mirroring should be disabled completely to avoid
the enumeration issue you are seeing on this platform. Please rebase on top of
the referenced patch (once v2 gets posted).

- Mani

[1] https://lore.kernel.org/linux-arm-msm/a01404d2-2f4d-4fb8-af9d-3db66d39acf7@quicinc.com/
-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH V6 1/4] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Manivannan Sadhasivam]

On Tue, Jul 16, 2024 at 02:53:44PM +0530, Sricharan R wrote:
> From: devi priya <quic_devipriy@quicinc.com>
> 
> Document the PCIe controller on IPQ9574 platform.
> 
> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

- Mani

> ---
>  [V6] Fixed the clocks order and dropped unnessecary names as per
>       Krzysztof's comments.
>       Changed the interrupt numbers/msi to '8'.
> 
>  .../devicetree/bindings/pci/qcom,pcie.yaml    | 50 +++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> index f867746b1ae5..2d61fb9f206d 100644
> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> @@ -26,6 +26,7 @@ properties:
>            - qcom,pcie-ipq8064-v2
>            - qcom,pcie-ipq8074
>            - qcom,pcie-ipq8074-gen3
> +          - qcom,pcie-ipq9574
>            - qcom,pcie-msm8996
>            - qcom,pcie-qcs404
>            - qcom,pcie-sdm845
> @@ -161,6 +162,7 @@ allOf:
>              enum:
>                - qcom,pcie-ipq6018
>                - qcom,pcie-ipq8074-gen3
> +              - qcom,pcie-ipq9574
>      then:
>        properties:
>          reg:
> @@ -397,6 +399,53 @@ allOf:
>              - const: axi_m_sticky # AXI Master Sticky reset
>              - const: axi_s_sticky # AXI Slave Sticky reset
>  
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - qcom,pcie-ipq9574
> +    then:
> +      properties:
> +        clocks:
> +          minItems: 6
> +          maxItems: 6
> +        clock-names:
> +          items:
> +            - const: axi_m # AXI Master clock
> +            - const: axi_s # AXI Slave clock
> +            - const: axi_bridge
> +            - const: rchng
> +            - const: ahb
> +            - const: aux
> +
> +        resets:
> +          minItems: 8
> +          maxItems: 8
> +        reset-names:
> +          items:
> +            - const: pipe # PIPE reset
> +            - const: sticky # Core Sticky reset
> +            - const: axi_s_sticky # AXI Slave Sticky reset
> +            - const: axi_s # AXI Slave reset
> +            - const: axi_m_sticky # AXI Master Sticky reset
> +            - const: axi_m # AXI Master reset
> +            - const: aux # AUX Reset
> +            - const: ahb # AHB Reset
> +
> +        interrupts:
> +          minItems: 8
> +        interrupt-names:
> +          items:
> +            - const: msi0
> +            - const: msi1
> +            - const: msi2
> +            - const: msi3
> +            - const: msi4
> +            - const: msi5
> +            - const: msi6
> +            - const: msi7
> +
>    - if:
>        properties:
>          compatible:
> @@ -507,6 +556,7 @@ allOf:
>                  - qcom,pcie-ipq8064v2
>                  - qcom,pcie-ipq8074
>                  - qcom,pcie-ipq8074-gen3
> +                - qcom,pcie-ipq9574
>                  - qcom,pcie-qcs404
>      then:
>        required:
> -- 
> 2.34.1
> 

-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH V6 2/4] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Sricharan Ramabadhran]

On 7/16/2024 5:33 PM, Konrad Dybcio wrote:
> On 16.07.2024 11:23 AM, Sricharan R wrote:
>> From: devi priya <quic_devipriy@quicinc.com>
>>
>> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
>> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
>> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>>
>> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
>> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
>> ---
> [...]
>
>> +
>> +			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
>> +				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
> Drop these comments, please
ok
>> +
>> +			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
>> +
> Inconsistent newline
ok, will fix
>> +			interrupt-names = "msi0",
>> +					  "msi1",
>> +					  "msi2",
>> +					  "msi3",
>> +					  "msi4",
>> +					  "msi5",
>> +					  "msi6",
>> +					  "msi7";
>> +
>> +			#interrupt-cells = <1>;
>> +			interrupt-map-mask = <0 0 0 0x7>;
>> +			interrupt-map = <0 0 0 1 &intc 0 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> +					<0 0 0 2 &intc 0 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> +					<0 0 0 3 &intc 0 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> +					<0 0 0 4 &intc 0 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> Drop these comments, please
>
> (all these comments apply to all the similar nodes)
ok
> [...]
>
>> +
>> +		pcie3: pcie@18000000 {
>> +			compatible = "qcom,pcie-ipq9574";
>> +			reg =  <0x18000000 0xf1d>,
>> +			       <0x18000f20 0xa8>,
>> +			       <0x18001000 0x1000>,
>> +			       <0x000f0000 0x4000>,
>> +			       <0x18100000 0x1000>;
>> +			reg-names = "dbi", "elbi", "atu", "parf", "config";
>> +			device_type = "pci";
>> +			linux,pci-domain = <4>;
> Any reason the PCI domain for PCIeN is N+1? You can start at 0
ok, will fix

Regards,
  Sricharan

Re: [PATCH V6 3/4] arm64: dts: qcom: ipq9574: Enable PCIe PHYs and controllers

[Sricharan Ramabadhran]

On 7/16/2024 5:33 PM, Konrad Dybcio wrote:
> On 16.07.2024 11:23 AM, Sricharan R wrote:
>> From: devi priya <quic_devipriy@quicinc.com>
>>
>> Enable the PCIe controller and PHY nodes corresponding to RDP 433.
>>
>> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
>> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
>> ---
>>   [V6] No change.
>>
>>   arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 113 ++++++++++++++++++++
>>   1 file changed, 113 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> index 1bb8d96c9a82..f4b6d540612c 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> @@ -8,6 +8,7 @@
>>   
>>   /dts-v1/;
>>   
>> +#include <dt-bindings/gpio/gpio.h>
>>   #include "ipq9574-rdp-common.dtsi"
>>   
>>   / {
>> @@ -15,6 +16,45 @@ / {
>>   	compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
>>   };
>>   
>> +&pcie1_phy {
>> +	status = "okay";
>> +};
>> +
>> +&pcie1 {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pcie1_default>;
> property-n
> property-names
ok, will fix

Regards,
  Sricharan

Re: [PATCH V6 1/4] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Sricharan Ramabadhran]

On 7/17/2024 1:12 AM, Krzysztof Kozlowski wrote:
> On 16/07/2024 11:23, Sricharan R wrote:
>> From: devi priya <quic_devipriy@quicinc.com>
>>
>> Document the PCIe controller on IPQ9574 platform.
> Subjects are without full stop.
ok, will fix.
> With that fixed:
>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Thanks

Regards,
  Sricharan

Re: [PATCH V6 4/4] PCI: qcom: Add support for IPQ9574

[Sricharan Ramabadhran]

On 7/17/2024 2:08 PM, Manivannan Sadhasivam wrote:
> On Tue, Jul 16, 2024 at 02:53:47PM +0530, Sricharan R wrote:
>> From: devi priya <quic_devipriy@quicinc.com>
>>
>> The IPQ9574 platform has four Gen3 PCIe controllers:
>> two single-lane and two dual-lane based on SNPS core 5.70a.
>>
>> QCOM IP rev is 1.27.0 and Synopsys IP rev is 5.80a.
>> Add a new compatible 'qcom,pcie-ipq9574' and 'ops_1_27_0'
>> which reuses all the members of 'ops_2_9_0' except for the
>> post_init as the SLV_ADDR_SPACE_SIZE configuration differs
>> between 2_9_0 and 1_27_0.
>>
>> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
>> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
>> ---
>>   [V6] Fixed all Manivannan's and Bjorn Helgaas comments.
>>        Removed the SLV_ADDR_SPACE_SZ_1_27_0 macro to have default value.
>>
>>   drivers/pci/controller/dwc/pcie-qcom.c | 31 ++++++++++++++++++++++----
>>   1 file changed, 27 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
>> index 0180edf3310e..26acd9f5385e 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
>> @@ -1116,16 +1116,13 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
>>   	return clk_bulk_prepare_enable(res->num_clks, res->clks);
>>   }
>>   
>> -static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>> +static int qcom_pcie_post_init(struct qcom_pcie *pcie)
>>   {
>>   	struct dw_pcie *pci = pcie->pci;
>>   	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>>   	u32 val;
>>   	int i;
>>   
>> -	writel(SLV_ADDR_SPACE_SZ,
>> -		pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
>> -
>>   	val = readl(pcie->parf + PARF_PHY_CTRL);
>>   	val &= ~PHY_TEST_PWR_DOWN;
>>   	writel(val, pcie->parf + PARF_PHY_CTRL);
>> @@ -1165,6 +1162,18 @@ static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>>   	return 0;
>>   }
>>   
>> +static int qcom_pcie_post_init_1_27_0(struct qcom_pcie *pcie)
>> +{
>> +	return qcom_pcie_post_init(pcie);
>> +}
>> +
>> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	writel(SLV_ADDR_SPACE_SZ, pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
>> +
> As discussed in [1], DBI/ATU mirroring should be disabled completely to avoid
> the enumeration issue you are seeing on this platform. Please rebase on top of
> the referenced patch (once v2 gets posted).
ok, got it.

Regards,
  Sricharan