From: Jeffrey Hugo <jhugo@codeaurora.org>
To: Kishon Vijay Abraham I <kishon@ti.com>,
Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: andy.gross@linaro.org, david.brown@linaro.org,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
robh+dt@kernel.org, mark.rutland@arm.com,
devicetree@vger.kernel.org, gregkh@linuxfoundation.org,
balbi@kernel.org, linux-usb@vger.kernel.org
Subject: Re: [PATCH v2 3/6] phy: qcom-qusb2: Add QUSB2 PHY support for msm8998
Date: Wed, 16 Jan 2019 08:28:27 -0700 [thread overview]
Message-ID: <c6b1887e-139a-6b3b-3f9e-d0842fbe8eeb@codeaurora.org> (raw)
In-Reply-To: <60137083-59d3-a04f-d55b-c5587038e946@ti.com>
On 1/16/2019 1:58 AM, Kishon Vijay Abraham I wrote:
> Hi,
>
> On 16/01/19 2:20 PM, Kishon Vijay Abraham I wrote:
>>
>>
>> On 15/01/19 11:41 PM, Bjorn Andersson wrote:
>>> On Mon 14 Jan 08:36 PST 2019, Jeffrey Hugo wrote:
>>>
>>>> MSM8998 contains one QUSB2 PHY which is very similar to the existing
>>>> sdm845 support.
>>>>
>>>
>> I don't seem to have the dt-binding patch in my inbox. Can you send them as well?
>
> Ignore my request. I found the patch.
Sorry about that. I was made aware there is something glitched when
sending this out, and the series didn't get threaded properly. I'll be
investigating and correcting for the next time I need to send out a series.
Is this change acceptable? I saw you picked up patch 1 (phy bindings)
and patch 4 (QMP phy changes), but not this one. I do want to see as
much of this hit 5.1 as possible, so if there is anything I need to
correct, please let me know. I'd be happy to update.
>
> Thanks
> Kishon
>
>>
>> Thanks
>> Kishon
>>> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
>>>
>>>> Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
>>>> ---
>>>> drivers/phy/qualcomm/phy-qcom-qusb2.c | 41 +++++++++++++++++++++++++++++++++++
>>>> 1 file changed, 41 insertions(+)
>>>>
>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
>>>> index 9177989f..e5e4f36 100644
>>>> --- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
>>>> @@ -152,6 +152,32 @@ enum qusb2phy_reg_layout {
>>>> QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
>>>> };
>>>>
>>>> +static const unsigned int msm8998_regs_layout[] = {
>>>> + [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
>>>> + [QUSB2PHY_PLL_STATUS] = 0x1a0,
>>>> + [QUSB2PHY_PORT_TUNE1] = 0x23c,
>>>> + [QUSB2PHY_PORT_TUNE2] = 0x240,
>>>> + [QUSB2PHY_PORT_TUNE3] = 0x244,
>>>> + [QUSB2PHY_PORT_TUNE4] = 0x248,
>>>> + [QUSB2PHY_PORT_TEST1] = 0x24c,
>>>> + [QUSB2PHY_PORT_TEST2] = 0x250,
>>>> + [QUSB2PHY_PORT_POWERDOWN] = 0x210,
>>>> + [QUSB2PHY_INTR_CTRL] = 0x22c,
>>>> +};
>>>> +
>>>> +static const struct qusb2_phy_init_tbl msm8998_init_tbl[] = {
>>>> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x13),
>>>> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
>>>> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
>>>> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
>>>> +
>>>> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xa5),
>>>> + QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x09),
>>>> +
>>>> + QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
>>>> +};
>>>> +
>>>> +
>>>> static const unsigned int sdm845_regs_layout[] = {
>>>> [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
>>>> [QUSB2PHY_PLL_STATUS] = 0x1a0,
>>>> @@ -221,6 +247,18 @@ struct qusb2_phy_cfg {
>>>> .autoresume_en = BIT(3),
>>>> };
>>>>
>>>> +static const struct qusb2_phy_cfg msm8998_phy_cfg = {
>>>> + .tbl = msm8998_init_tbl,
>>>> + .tbl_num = ARRAY_SIZE(msm8998_init_tbl),
>>>> + .regs = msm8998_regs_layout,
>>>> +
>>>> + .disable_ctrl = POWER_DOWN,
>>>> + .mask_core_ready = CORE_READY_STATUS,
>>>> + .has_pll_override = true,
>>>> + .autoresume_en = BIT(0),
>>>> + .update_tune1_with_efuse = true,
>>>> +};
>>>> +
>>>> static const struct qusb2_phy_cfg sdm845_phy_cfg = {
>>>> .tbl = sdm845_init_tbl,
>>>> .tbl_num = ARRAY_SIZE(sdm845_init_tbl),
>>>> @@ -734,6 +772,9 @@ static int qusb2_phy_exit(struct phy *phy)
>>>> .compatible = "qcom,msm8996-qusb2-phy",
>>>> .data = &msm8996_phy_cfg,
>>>> }, {
>>>> + .compatible = "qcom,msm8998-qusb2-phy",
>>>> + .data = &msm8998_phy_cfg,
>>>> + }, {
>>>> .compatible = "qcom,sdm845-qusb2-phy",
>>>> .data = &sdm845_phy_cfg,
>>>> },
>>>> --
>>>> Qualcomm Datacenter Technologies as an affiliate of Qualcomm Technologies, Inc.
>>>> Qualcomm Technologies, Inc. is a member of the
>>>> Code Aurora Forum, a Linux Foundation Collaborative Project.
>>>>
--
Jeffrey Hugo
Qualcomm Datacenter Technologies as an affiliate of Qualcomm
Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
next prev parent reply other threads:[~2019-01-16 15:28 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-14 16:36 [PATCH v2 3/6] phy: qcom-qusb2: Add QUSB2 PHY support for msm8998 Jeffrey Hugo
2019-01-15 18:11 ` Bjorn Andersson
2019-01-16 8:50 ` Kishon Vijay Abraham I
2019-01-16 8:58 ` Kishon Vijay Abraham I
2019-01-16 15:28 ` Jeffrey Hugo [this message]
2019-01-17 10:52 ` Kishon Vijay Abraham I
2019-01-17 17:57 ` Jeffrey Hugo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c6b1887e-139a-6b3b-3f9e-d0842fbe8eeb@codeaurora.org \
--to=jhugo@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=balbi@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).