Re: [PATCH v2 2/4] PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property

[Kishon Vijay Abraham I <kishon@ti.com>]

Hi Robin,

On 5/4/2020 4:24 PM, Robin Murphy wrote:
> On 2020-05-04 9:44 am, Kishon Vijay Abraham I wrote:
>> Hi Robin,
>>
>> On 5/1/2020 9:24 PM, Robin Murphy wrote:
>>> On 2020-05-01 3:46 pm, Lorenzo Pieralisi wrote:
>>>> [+Robin - to check on dma-ranges intepretation]
>>>>
>>>> I would need RobH and Robin to review this.
>>>>
>>>> Also, An ACK from Tom is required - for the whole series.
>>>>
>>>> On Fri, Apr 17, 2020 at 05:13:20PM +0530, Kishon Vijay Abraham I wrote:
>>>>> Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
>>>>> property to configure the number of bits passed through from PCIe
>>>>> address to internal address in Inbound Address Translation register.
>>>>>
>>>>> However standard PCI dt-binding already defines "dma-ranges" to
>>>>> describe the address range accessible by PCIe controller. Parse
>>>>> "dma-ranges" property to configure the number of bits passed
>>>>> through from PCIe address to internal address in Inbound Address
>>>>> Translation register.
>>>>>
>>>>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>>>>> ---
>>>>>    drivers/pci/controller/cadence/pcie-cadence-host.c | 13 +++++++++++--
>>>>>    1 file changed, 11 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/drivers/pci/controller/cadence/pcie-cadence-host.c
>>>>> b/drivers/pci/controller/cadence/pcie-cadence-host.c
>>>>> index 9b1c3966414b..60f912a657b9 100644
>>>>> --- a/drivers/pci/controller/cadence/pcie-cadence-host.c
>>>>> +++ b/drivers/pci/controller/cadence/pcie-cadence-host.c
>>>>> @@ -206,8 +206,10 @@ int cdns_pcie_host_setup(struct cdns_pcie_rc *rc)
>>>>>        struct device *dev = rc->pcie.dev;
>>>>>        struct platform_device *pdev = to_platform_device(dev);
>>>>>        struct device_node *np = dev->of_node;
>>>>> +    struct of_pci_range_parser parser;
>>>>>        struct pci_host_bridge *bridge;
>>>>>        struct list_head resources;
>>>>> +    struct of_pci_range range;
>>>>>        struct cdns_pcie *pcie;
>>>>>        struct resource *res;
>>>>>        int ret;
>>>>> @@ -222,8 +224,15 @@ int cdns_pcie_host_setup(struct cdns_pcie_rc *rc)
>>>>>        rc->max_regions = 32;
>>>>>        of_property_read_u32(np, "cdns,max-outbound-regions",
>>>>> &rc->max_regions);
>>>>>    -    rc->no_bar_nbits = 32;
>>>>> -    of_property_read_u32(np, "cdns,no-bar-match-nbits", &rc->no_bar_nbits);
>>>>> +    if (!of_pci_dma_range_parser_init(&parser, np))
>>>>> +        if (of_pci_range_parser_one(&parser, &range))
>>>>> +            rc->no_bar_nbits = ilog2(range.size);
>>>
>>> You probably want "range.pci_addr + range.size" here just in case the bottom of
>>> the window is ever non-zero. Is there definitely only ever a single inbound
>>> window to consider?
>>
>> Cadence IP has 3 inbound address translation registers, however we use only 1
>> inbound address translation register to map the entire 32 bit or 64 bit address
>> region.
> 
> OK, if anything that further strengthens the argument for deprecating a single
> "number of bits" property in favour of ranges that accurately describe the
> window(s). However it also suggests that other users in future might have some
> expectation that specifying "dma-ranges" with up to 3 entries should work to
> allow a more restrictive inbound configuration. Thus it would be desirable to
> make the code a little more robust here - even if we don't support multiple
> windows straight off, it would still be better to implement it in a way that
> can be cleanly extended later, and at least say something if more ranges are
> specified rather than just silently ignoring them.

I looked at this further in the Cadence user doc. The three inbound ATU entries
are for BAR0, BAR1 in RC configuration space and the third one is for NO MATCH
BAR when there is no matching found in RC BARs. Right now we always configure
the NO MATCH BAR. Would it be possible describe at BAR granularity in dma-ranges?
> 
>>> I believe that pci_parse_request_of_pci_ranges() could do the actual parsing
>>> for you, but I suppose plumbing that in plus processing the resulting
>>> dma_ranges resource probably ends up a bit messier than the concise open-coding
>>> here.
>>
>> right, pci_parse_request_of_pci_ranges() parses "ranges" property and is used
>> for outbound configuration, whereas here we parse "dma-ranges" property and is
>> used for inbound configuration.
> 
> If you give it a valid third argument it *also* parses "dma-ranges" into a list
> of inbound regions. This is already used by various other drivers for
> equivalent inbound window setup, which is what I was hinting at before, but
> given the extensibility argument above I'm now going to actively suggest
> following that pattern for consistency.
yeah, just got to know about this.

Thanks
Kishon