[PATCH v8 0/5] Enable IPQ5332 USB2

[PATCH v8 0/5] Enable IPQ5332 USB2

[Varadarajan Narayanan]

This patch series adds the relevant phy and controller
configurations for enabling USB2 on IPQ5332

v8:
	Driver:-
		Change commit subject and message per review comments
		Don't include of_platform.h
		Change struct initialization coding style
		GENMASK -> BIT for one of the defines
v7:
	Binding:-
		Move 'compatible' to be the first entry
		In the example have 'usb-phy' instead of 'usb2-phy'
		Add 'Reviewed-by: Krzysztof Kozlowski'
v6:
	Binding and dts:-
		Dropped the qcom,dwc3.yaml patch as it has been picked up for linux-next
		Add const to compatible, vdd-supply
		Move nodes per register address
	Driver:-
		Add vdd-supply
		Cleanup error paths in probe with dev_err_probe
v5:
	Binding and dts:-
		Fix email id
		Removed 'Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>'
		as had to change bindings file to be able to use generic phy instead of
		usb-phy

	Driver:-
		Remove unused definition
		Use generic phy instead of usb-phy
v4:
	Binding and dts:-
		Change node name (bindings & dts)
	Driver:-
		Remove unused enum
		static const for '.data'
		Error handling for devm_clk_get
v3:
	Fix bindings file based on review comments

v1:
	Cleanup DTS
	Combine driver, kconfig and makefile patches
	Remove unused functions from M31 driver
	Drop the clock driver changes

Varadarajan Narayanan (5):
  dt-bindings: phy: qcom,m31: Document qcom,m31 USB phy
  phy: qcom: Introduce M31 USB PHY driver
  arm64: dts: qcom: ipq5332: Add USB related nodes
  arm64: dts: qcom: ipq5332: Enable USB
  arm64: defconfig: Enable M31 USB phy driver

 .../bindings/phy/qcom,ipq5332-usb-hsphy.yaml       |  59 +++++
 arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts        |  23 ++
 arch/arm64/boot/dts/qcom/ipq5332.dtsi              |  55 ++++
 arch/arm64/configs/defconfig                       |   1 +
 drivers/phy/qualcomm/Kconfig                       |  11 +
 drivers/phy/qualcomm/Makefile                      |   1 +
 drivers/phy/qualcomm/phy-qcom-m31.c                | 294 +++++++++++++++++++++
 7 files changed, 444 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
 create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c

-- 
2.7.4

[PATCH v8 1/5] dt-bindings: phy: qcom,m31: Document qcom,m31 USB phy

[Varadarajan Narayanan]

Document the M31 USB2 phy present in IPQ5332.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v7:
	Move 'compatible' to be the first entry
	In the example have 'usb-phy' instead of 'usb2-phy'
	Add 'Reviewed-by: Krzysztof Kozlowski'
	'make dt_binding_check DT_SCHEMA_FILES=qcom,ipq5332-usb-hsphy.yaml' passed
	'make CHECK_DTBS=y DT_SCHEMA_FILES=qcom,ipq5332-usb-hsphy.yaml dtbs_check' passed
v6:
	Add 'Co-developed-by: Sricharan'
	Add 'const' to compatible, vdd-supply
	Remove label and use usb2-phy for nodename in the example
v5:
	Add '#phy-cells', to be able to use generic phy
	Remove 'Reviewed-by: Krzysztof Kozlowski' due to above change
v4:
	Move M31 URL to description
	Remove maxItems and relevant content from clock-names
	Change node name to generic name
	'make dt_binding_check DT_SCHEMA_FILES=qcom' passed
v3:
	Incorporate review comments. Will bring in ipq5018 compatible
	string while posting ipq5018 usb patchset.

v1:
	Rename qcom,m31.yaml -> qcom,ipq5332-usb-hsphy.yaml
	Drop default binding "m31,usb-hsphy"
	Add clock
	Remove 'oneOf' from compatible
	Remove 'qscratch' region from register space as it is not needed
	Remove reset-names
	Fix the example definition
---
 .../bindings/phy/qcom,ipq5332-usb-hsphy.yaml       | 59 ++++++++++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml

diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
new file mode 100644
index 0000000..2671a04
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/qcom,ipq5332-usb-hsphy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: M31 USB PHY
+
+maintainers:
+  - Sricharan Ramabadhran <quic_srichara@quicinc.com>
+  - Varadarajan Narayanan <quic_varada@quicinc.com>
+
+description:
+  USB M31 PHY (https://www.m31tech.com) found in Qualcomm
+  IPQ5018, IPQ5332 SoCs.
+
+properties:
+  compatible:
+    items:
+      - const: qcom,ipq5332-usb-hsphy
+
+  "#phy-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: cfg_ahb
+
+  resets:
+    maxItems: 1
+
+  vdd-supply:
+    description:
+      Phandle to 5V regulator supply to PHY digital circuit.
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,ipq5332-gcc.h>
+    usb-phy@7b000 {
+        compatible = "qcom,ipq5332-usb-hsphy";
+        reg = <0x0007b000 0x12c>;
+
+        clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;
+        clock-names = "cfg_ahb";
+
+        #phy-cells = <0>;
+
+        resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+
+        vdd-supply = <&regulator_fixed_5p0>;
+    };
-- 
2.7.4

[PATCH v8 2/5] phy: qcom: Introduce M31 USB PHY driver

[Varadarajan Narayanan]

Add the M31 USB2 phy driver for the USB M31 PHY
(https://www.m31tech.com) found in Qualcomm IPQ5018, IPQ5332
SoCs.

Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v8:
	Change commit subject and message per review comments
	Don't include of_platform.h
	Change struct init coding style
	GENMASK -> BIT for one define
v6:
	Kconfig:Add COMPILE_TEST and remove USB_GADGET from 'depends'
		Change 'selects' USB_PHY -> GENERIC_PHY
	Driver:	Use correct headers
		const int -> unsigned int for 'nregs' in private data
		Use generic names for clk, phy in m31 phy structure
		Init register details directly instead of using macro
		Use dev_err_probe in the error paths of driver probe
v5:
	Kconfig and Makefile:- place snippet according to sorted order
	Use generic phy instead of usb-phy
	Use ARRAY_SIZE for reg init instead of blank last entry
	Fix copyright year

v4:
	Remove unused enum
	Error handling for devm_clk_get
v1:
	Combine driver, makefile and kconfig into 1 patch
	Remove 'qscratch' region and its usage. The controller driver takes care
	of those settings
	Use compatible/data to handle ipq5332 init
	Drop the default case
	Get resources by index instead of name as there is only one resource
	Add clock
	Fix review comments in the driver
---
 drivers/phy/qualcomm/Kconfig        |  11 ++
 drivers/phy/qualcomm/Makefile       |   1 +
 drivers/phy/qualcomm/phy-qcom-m31.c | 294 ++++++++++++++++++++++++++++++++++++
 3 files changed, 306 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index ced6038..d891058 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -143,6 +143,17 @@ config PHY_QCOM_EUSB2_REPEATER
 	  PMICs. The repeater is paired with a Synopsys eUSB2 Phy
 	  on Qualcomm SOCs.
 
+config PHY_QCOM_M31_USB
+	tristate "Qualcomm M31 HS PHY driver support"
+	depends on USB && (ARCH_QCOM || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable this to support M31 HS PHY transceivers on Qualcomm chips
+	  with DWC3 USB core. It handles PHY initialization, clock
+	  management required after resetting the hardware and power
+	  management. This driver is required even for peripheral only or
+	  host only mode configurations.
+
 config PHY_QCOM_USB_HS
 	tristate "Qualcomm USB HS PHY module"
 	depends on USB_ULPI_BUS
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index df94581..ffd609a 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -4,6 +4,7 @@ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
 obj-$(CONFIG_PHY_QCOM_EDP)		+= phy-qcom-edp.o
 obj-$(CONFIG_PHY_QCOM_IPQ4019_USB)	+= phy-qcom-ipq4019-usb.o
 obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_M31_USB)		+= phy-qcom-m31.o
 obj-$(CONFIG_PHY_QCOM_PCIE2)		+= phy-qcom-pcie2.o
 
 obj-$(CONFIG_PHY_QCOM_QMP_COMBO)	+= phy-qcom-qmp-combo.o
diff --git a/drivers/phy/qualcomm/phy-qcom-m31.c b/drivers/phy/qualcomm/phy-qcom-m31.c
new file mode 100644
index 0000000..ed08072
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-m31.c
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2014-2023, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define USB2PHY_PORT_UTMI_CTRL1		0x40
+
+#define USB2PHY_PORT_UTMI_CTRL2		0x44
+ #define UTMI_ULPI_SEL			BIT(7)
+ #define UTMI_TEST_MUX_SEL		BIT(6)
+
+#define HS_PHY_CTRL_REG			0x10
+ #define UTMI_OTG_VBUS_VALID		BIT(20)
+ #define SW_SESSVLD_SEL			BIT(28)
+
+#define USB_PHY_UTMI_CTRL0		0x3c
+
+#define USB_PHY_UTMI_CTRL5		0x50
+ #define POR_EN				BIT(1)
+
+#define USB_PHY_HS_PHY_CTRL_COMMON0	0x54
+ #define COMMONONN			BIT(7)
+ #define FSEL				BIT(4)
+ #define RETENABLEN			BIT(3)
+ #define FREQ_24MHZ			(BIT(6) | BIT(4))
+
+#define USB_PHY_HS_PHY_CTRL2		0x64
+ #define USB2_SUSPEND_N_SEL		BIT(3)
+ #define USB2_SUSPEND_N			BIT(2)
+ #define USB2_UTMI_CLK_EN		BIT(1)
+
+#define USB_PHY_CFG0			0x94
+ #define UTMI_PHY_OVERRIDE_EN		BIT(1)
+
+#define USB_PHY_REFCLK_CTRL		0xa0
+ #define CLKCORE			BIT(1)
+
+#define USB2PHY_PORT_POWERDOWN		0xa4
+ #define POWER_UP			BIT(0)
+ #define POWER_DOWN			0
+
+#define USB_PHY_FSEL_SEL		0xb8
+ #define FREQ_SEL			BIT(0)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_1	0xbc
+ #define USB2_0_TX_ENABLE		BIT(2)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_4	0xc8
+ #define HSTX_SLEW_RATE_565PS		GENMASK(1, 0)
+ #define PLL_CHARGING_PUMP_CURRENT_35UA	GENMASK(4, 3)
+ #define ODT_VALUE_38_02_OHM		GENMASK(7, 6)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_5	0xcc
+ #define ODT_VALUE_45_02_OHM		BIT(2)
+ #define HSTX_PRE_EMPHASIS_LEVEL_0_55MA	BIT(0)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_11	0xe4
+ #define XCFG_COARSE_TUNE_NUM		BIT(1)
+ #define XCFG_FINE_TUNE_NUM		BIT(3)
+
+struct m31_phy_regs {
+	u32 off;
+	u32 val;
+	u32 delay;
+};
+
+struct m31_priv_data {
+	bool				ulpi_mode;
+	const struct m31_phy_regs	*regs;
+	unsigned int			nregs;
+};
+
+struct m31_phy_regs m31_ipq5332_regs[] = {
+	{
+		USB_PHY_CFG0,
+		UTMI_PHY_OVERRIDE_EN,
+		0
+	},
+	{
+		USB_PHY_UTMI_CTRL5,
+		POR_EN,
+		15
+	},
+	{
+		USB_PHY_FSEL_SEL,
+		FREQ_SEL,
+		0
+	},
+	{
+		USB_PHY_HS_PHY_CTRL_COMMON0,
+		COMMONONN | FREQ_24MHZ | RETENABLEN,
+		0
+	},
+	{
+		USB_PHY_UTMI_CTRL5,
+		POR_EN,
+		0
+	},
+	{
+		USB_PHY_HS_PHY_CTRL2,
+		USB2_SUSPEND_N_SEL | USB2_SUSPEND_N | USB2_UTMI_CLK_EN,
+		0
+	},
+	{
+		USB2PHY_USB_PHY_M31_XCFGI_11,
+		XCFG_COARSE_TUNE_NUM  | XCFG_FINE_TUNE_NUM,
+		0
+	},
+	{
+		USB2PHY_USB_PHY_M31_XCFGI_4,
+		HSTX_SLEW_RATE_565PS | PLL_CHARGING_PUMP_CURRENT_35UA | ODT_VALUE_38_02_OHM,
+		0
+	},
+	{
+		USB2PHY_USB_PHY_M31_XCFGI_1,
+		USB2_0_TX_ENABLE,
+		0
+	},
+	{
+		USB2PHY_USB_PHY_M31_XCFGI_5,
+		ODT_VALUE_45_02_OHM | HSTX_PRE_EMPHASIS_LEVEL_0_55MA,
+		4
+	},
+	{
+		USB_PHY_UTMI_CTRL5,
+		0x0,
+		0
+	},
+	{
+		USB_PHY_HS_PHY_CTRL2,
+		USB2_SUSPEND_N | USB2_UTMI_CLK_EN,
+		0
+	},
+};
+
+struct m31usb_phy {
+	struct phy			*phy;
+	void __iomem			*base;
+	const struct m31_phy_regs	*regs;
+	int				nregs;
+
+	struct regulator		*vreg;
+	struct clk			*clk;
+	struct reset_control		*reset;
+
+	bool				ulpi_mode;
+};
+
+static int m31usb_phy_init(struct phy *phy)
+{
+	struct m31usb_phy *qphy = phy_get_drvdata(phy);
+	const struct m31_phy_regs *regs = qphy->regs;
+	int i, ret;
+
+	ret = regulator_enable(qphy->vreg);
+	if (ret) {
+		dev_err(&phy->dev, "failed to enable regulator, %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(qphy->clk);
+	if (ret) {
+		if (qphy->vreg)
+			regulator_disable(qphy->vreg);
+		dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+		return ret;
+	}
+
+	/* Perform phy reset */
+	reset_control_assert(qphy->reset);
+	udelay(5);
+	reset_control_deassert(qphy->reset);
+
+	/* configure for ULPI mode if requested */
+	if (qphy->ulpi_mode)
+		writel(0x0, qphy->base + USB2PHY_PORT_UTMI_CTRL2);
+
+	/* Enable the PHY */
+	writel(POWER_UP, qphy->base + USB2PHY_PORT_POWERDOWN);
+
+	/* Turn on phy ref clock */
+	for (i = 0; i < qphy->nregs; i++) {
+		writel(regs[i].val, qphy->base + regs[i].off);
+		if (regs[i].delay)
+			udelay(regs[i].delay);
+	}
+
+	return 0;
+}
+
+static int m31usb_phy_shutdown(struct phy *phy)
+{
+	struct m31usb_phy *qphy = phy_get_drvdata(phy);
+
+	/* Disable the PHY */
+	writel_relaxed(POWER_DOWN, qphy->base + USB2PHY_PORT_POWERDOWN);
+
+	clk_disable_unprepare(qphy->clk);
+
+	regulator_disable(qphy->vreg);
+
+	return 0;
+}
+
+static const struct phy_ops m31usb_phy_gen_ops = {
+	.power_on	= m31usb_phy_init,
+	.power_off	= m31usb_phy_shutdown,
+	.owner		= THIS_MODULE,
+};
+
+static int m31usb_phy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	const struct m31_priv_data *data;
+	struct device *dev = &pdev->dev;
+	struct m31usb_phy *qphy;
+
+	qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+	if (!qphy)
+		return -ENOMEM;
+
+	qphy->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(qphy->base))
+		return PTR_ERR(qphy->base);
+
+	qphy->reset = devm_reset_control_get_exclusive_by_index(dev, 0);
+	if (IS_ERR(qphy->reset))
+		return PTR_ERR(qphy->reset);
+
+	qphy->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(qphy->clk))
+		return dev_err_probe(dev, PTR_ERR(qphy->clk),
+						"failed to get clk\n");
+
+	data = of_device_get_match_data(dev);
+	qphy->regs		= data->regs;
+	qphy->nregs		= data->nregs;
+	qphy->ulpi_mode		= data->ulpi_mode;
+
+	qphy->phy = devm_phy_create(dev, NULL, &m31usb_phy_gen_ops);
+	if (IS_ERR(qphy->phy))
+		return dev_err_probe(dev, PTR_ERR(qphy->phy),
+						"failed to create phy\n");
+
+	qphy->vreg = devm_regulator_get(dev, "vdda-phy");
+	if (IS_ERR(qphy->vreg))
+		return dev_err_probe(dev, PTR_ERR(qphy->phy),
+						"failed to get vreg\n");
+
+	phy_set_drvdata(qphy->phy, qphy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (!IS_ERR(phy_provider))
+		dev_info(dev, "Registered M31 USB phy\n");
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct m31_priv_data m31_ipq5332_data = {
+	.ulpi_mode = false,
+	.regs = m31_ipq5332_regs,
+	.nregs = ARRAY_SIZE(m31_ipq5332_regs),
+};
+
+static const struct of_device_id m31usb_phy_id_table[] = {
+	{ .compatible = "qcom,ipq5332-usb-hsphy", .data = &m31_ipq5332_data },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, m31usb_phy_id_table);
+
+static struct platform_driver m31usb_phy_driver = {
+	.probe = m31usb_phy_probe,
+	.driver = {
+		.name = "qcom-m31usb-phy",
+		.of_match_table = m31usb_phy_id_table,
+	},
+};
+
+module_platform_driver(m31usb_phy_driver);
+
+MODULE_DESCRIPTION("USB2 Qualcomm M31 HSPHY driver");
+MODULE_LICENSE("GPL");
-- 
2.7.4

[PATCH v8 3/5] arm64: dts: qcom: ipq5332: Add USB related nodes

[Varadarajan Narayanan]

Add USB phy and controller nodes.

Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v6:
	Remove clock names
	Move the nodes to address sorted location
v5:
	Use generic phy instead of usb-phy
	'make CHECK_DTBS=y DT_SCHEMA_FILES=qcom dtbs_check' passed
	'DT_CHECKER_FLAGS='-v -m' DT_SCHEMA_FILES=qcom dt_binding_check' passed
v4:
	Change node name
	Remove blank line
	'make CHECK_DTBS=y DT_SCHEMA_FILES=qcom qcom/ipq5332-rdp441.dtb' passed
v1:
	Rename phy node
	Change compatible from m31,ipq5332-usb-hsphy -> qcom,ipq5332-usb-hsphy
	Remove 'qscratch' from phy node
	Fix alignment and upper-case hex no.s
	Add clock definition for the phy
	Remove snps,ref-clock-period-ns as it is not used. dwc3_ref_clk_period()
	in dwc3/core.c takes the frequency from ref clock and calculates fladj
	as appropriate.
---
 arch/arm64/boot/dts/qcom/ipq5332.dtsi | 55 +++++++++++++++++++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
index 8bfc2db..c45d9d4 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
@@ -145,6 +145,19 @@
 		#size-cells = <1>;
 		ranges = <0 0 0 0xffffffff>;
 
+		usbphy0: phy@7b000 {
+			compatible = "qcom,ipq5332-usb-hsphy";
+			reg = <0x0007b000 0x12c>;
+
+			clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;
+
+			resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		qfprom: efuse@a4000 {
 			compatible = "qcom,ipq5332-qfprom", "qcom,qfprom";
 			reg = <0x000a4000 0x721>;
@@ -290,6 +303,48 @@
 			status = "disabled";
 		};
 
+		usb: usb2@8a00000 {
+			compatible = "qcom,ipq5332-dwc3", "qcom,dwc3";
+			reg = <0x08af8800 0x400>;
+
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq";
+
+			clocks = <&gcc GCC_USB0_MASTER_CLK>,
+				 <&gcc GCC_SNOC_USB_CLK>,
+				 <&gcc GCC_USB0_SLEEP_CLK>,
+				 <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+			clock-names = "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
+
+			resets = <&gcc GCC_USB_BCR>;
+
+			qcom,select-utmi-as-pipe-clk;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			usb2_0_dwc: usb@8a00000 {
+				compatible = "snps,dwc3";
+				reg = <0x08a00000 0xe000>;
+				clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+				clock-names = "ref";
+				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+				phy-names = "usb2-phy";
+				phys = <&usbphy0>;
+				tx-fifo-resize;
+				snps,is-utmi-l1-suspend;
+				snps,hird-threshold = /bits/ 8 <0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
 			reg = <0x0b000000 0x1000>,	/* GICD */
-- 
2.7.4

[PATCH v8 4/5] arm64: dts: qcom: ipq5332: Enable USB

[Varadarajan Narayanan]

Enable USB2 in host mode.

Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v6:
	Add vdd-supply and corresponding regulator
v1:
	Enable usb-phy node
---
 arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
index f96b0c8..b4099a2f 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
@@ -12,6 +12,15 @@
 / {
 	model = "Qualcomm Technologies, Inc. IPQ5332 MI01.6";
 	compatible = "qcom,ipq5332-ap-mi01.6", "qcom,ipq5332";
+
+	regulator_fixed_5p0: s0500 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <500000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-name = "fixed_5p0";
+	};
 };
 
 &blsp1_spi0 {
@@ -79,3 +88,17 @@
 		bias-pull-up;
 	};
 };
+
+&usbphy0 {
+	vdd-supply = <&regulator_fixed_5p0>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_0_dwc {
+	dr_mode = "host";
+};
-- 
2.7.4

[PATCH v8 5/5] arm64: defconfig: Enable M31 USB phy driver

[Varadarajan Narayanan]

Enable M31 USB phy driver present in IPQ5332.

Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v2:
	Add full stop to commit log.
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index bf13d5c..04daaac 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1416,6 +1416,7 @@ CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=m
 CONFIG_PHY_QCOM_USB_HS_28NM=m
 CONFIG_PHY_QCOM_USB_SS=m
 CONFIG_PHY_QCOM_SGMII_ETH=m
+CONFIG_PHY_QCOM_M31_USB=m
 CONFIG_PHY_R8A779F0_ETHERNET_SERDES=y
 CONFIG_PHY_RCAR_GEN3_PCIE=y
 CONFIG_PHY_RCAR_GEN3_USB2=y
-- 
2.7.4

Re: [PATCH v8 2/5] phy: qcom: Introduce M31 USB PHY driver

[Bjorn Andersson]

On Mon, Aug 14, 2023 at 01:36:02PM +0530, Varadarajan Narayanan wrote:
> Add the M31 USB2 phy driver for the USB M31 PHY
> (https://www.m31tech.com) found in Qualcomm IPQ5018, IPQ5332
> SoCs.
> 

Thanks, this looks good to me now.

Reviewed-by: Bjorn Andersson <andersson@kernel.org>

Regards,
Bjorn

Re: (subset) [PATCH v8 0/5] Enable IPQ5332 USB2

[Vinod Koul]

On Mon, 14 Aug 2023 13:36:00 +0530, Varadarajan Narayanan wrote:
> This patch series adds the relevant phy and controller
> configurations for enabling USB2 on IPQ5332
> 
> v8:
> 	Driver:-
> 		Change commit subject and message per review comments
> 		Don't include of_platform.h
> 		Change struct initialization coding style
> 		GENMASK -> BIT for one of the defines
> v7:
> 	Binding:-
> 		Move 'compatible' to be the first entry
> 		In the example have 'usb-phy' instead of 'usb2-phy'
> 		Add 'Reviewed-by: Krzysztof Kozlowski'
> v6:
> 	Binding and dts:-
> 		Dropped the qcom,dwc3.yaml patch as it has been picked up for linux-next
> 		Add const to compatible, vdd-supply
> 		Move nodes per register address
> 	Driver:-
> 		Add vdd-supply
> 		Cleanup error paths in probe with dev_err_probe
> v5:
> 	Binding and dts:-
> 		Fix email id
> 		Removed 'Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>'
> 		as had to change bindings file to be able to use generic phy instead of
> 		usb-phy
> 
> [...]

Applied, thanks!

[1/5] dt-bindings: phy: qcom,m31: Document qcom,m31 USB phy
      commit: b11f8acb937ed64841eeba22b0f0371ded58bef2
[2/5] phy: qcom: Introduce M31 USB PHY driver
      commit: 9bc2b3b35334aa2742ad3dc4219c001279a97998

Best regards,
-- 
~Vinod