[PATCH v4 0/3] s32g: Use a syscon for GPR

[PATCH v4 0/3] s32g: Use a syscon for GPR

[Dan Carpenter]

The s32g devices have a GPR register region which holds a number of
miscellaneous registers.  Currently only the stmmac/dwmac-s32.c uses
anything from there and we just add a line to the device tree to
access that GMAC_0_CTRL_STS register:

                        reg = <0x4033c000 0x2000>, /* gmac IP */
                              <0x4007c004 0x4>;    /* GMAC_0_CTRL_STS */

I have included the whole list of registers below.

We still have to maintain backwards compatibility to this format,
of course, but it would be better to access these registers through a
syscon.  Putting all the registers together is more organized and shows
how the hardware actually is implemented.

Secondly, in some versions of this chipset those registers can only be
accessed via SCMI.  It's relatively straight forward to handle this
by writing a syscon driver and registering it with of_syscon_register_regmap()
but it's complicated to deal with if the registers aren't grouped
together.

Changes since v3:
* Fix the yaml file format
* Add netdev to the CC list on all emails so the CI triggers

Changes since v2:
* Improve the documentation in .../bindings/net/nxp,s32-dwmac.yaml
* "[PATCH v2 2/4] dt-bindings: mfd: syscon: Document the GPR syscon
  for the NXP S32 SoCs" was applied so drop it.

Changes since v1:
* Add imx@lists.linux.dev to the CC list.
* Fix forward porting bug.  s/PHY_INTF_SEL_RGMII/S32_PHY_INTF_SEL_RGMII/
* Use the correct SoC names nxp,s32g2-gpr and nxp,s32g3-gpr instead of
  nxp,s32g-gpr which is the SoC family.
* Fix the phandle name by adding the vendor prefix
* Fix the documentation for the phandle
* Remove #address-cells and #size-cells from the syscon block

Here is the whole list of registers in the GPR region

Starting from 0x4007C000

0  Software-Triggered Faults (SW_NCF)
4  GMAC Control (GMAC_0_CTRL_STS)
28 CMU Status 1 (CMU_STATUS_REG1)
2C CMUs Status 2 (CMU_STATUS_REG2)
30 FCCU EOUT Override Clear (FCCU_EOUT_OVERRIDE_CLEAR_REG)
38 SRC POR Control (SRC_POR_CTRL_REG)
54 GPR21 (GPR21)
5C GPR23 (GPR23)
60 GPR24 Register (GPR24)
CC Debug Control (DEBUG_CONTROL)
F0 Timestamp Control (TIMESTAMP_CONTROL_REGISTER)
F4 FlexRay OS Tick Input Select (FLEXRAY_OS_TICK_INPUT_SELECT_REG)
FC GPR63 Register (GPR63)

Starting from 0x4007CA00

0  Coherency Enable for PFE Ports (PFE_COH_EN)
4  PFE EMAC Interface Mode (PFE_EMACX_INTF_SEL)
20 PFE EMACX Power Control (PFE_PWR_CTRL)
28 Error Injection on Cortex-M7 AHB and AXI Pipe (CM7_TCM_AHB_SLICE)
2C Error Injection AHBP Gasket Cortex-M7 (ERROR_INJECTION_AHBP_GASKET_CM7)
40 LLCE Subsystem Status (LLCE_STAT)
44 LLCE Power Control (LLCE_CTRL)
48 DDR Urgent Control (DDR_URGENT_CTRL)
4C FTM Global Load Control (FLXTIM_CTRL)
50 FTM LDOK Status (FLXTIM_STAT)
54 Top CMU Status (CMU_STAT)
58 Accelerator NoC No Pending Trans Status (NOC_NOPEND_TRANS)
90 SerDes RD/WD Toggle Control (PCIE_TOGGLE)
94 SerDes Toggle Done Status (PCIE_TOGGLEDONE_STAT)
E0 Generic Control 0 (GENCTRL0)
E4 Generic Control 1 (GENCTRL1)
F0 Generic Status 0 (GENSTAT0)
FC Cortex-M7 AXI Parity Error and AHBP Gasket Error Alarm (CM7_AXI_AHBP_GASKET_ERROR_ALARM)

Starting from 4007C800

4  GPR01 Register (GPR01)
30 GPR12 Register (GPR12)
58 GPR22 Register (GPR22)
70 GPR28 Register (GPR28)
74 GPR29 Register (GPR29)

Starting from 4007CB00

4 WKUP Pad Pullup/Pulldown Select (WKUP_PUS)

Dan Carpenter (3):
  net: stmmac: s32: use a syscon for S32_PHY_INTF_SEL_RGMII
  dt-bindings: net: nxp,s32-dwmac: Use the GPR syscon
  dts: s32g: Add GPR syscon region

 .../bindings/net/nxp,s32-dwmac.yaml           | 12 ++++++++++
 arch/arm64/boot/dts/freescale/s32g2.dtsi      |  6 +++++
 arch/arm64/boot/dts/freescale/s32g3.dtsi      |  6 +++++
 .../net/ethernet/stmicro/stmmac/dwmac-s32.c   | 23 +++++++++++++++----
 4 files changed, 42 insertions(+), 5 deletions(-)

-- 
2.51.0
*** BLURB HERE ***

Dan Carpenter (3):
  net: stmmac: s32: use a syscon for S32_PHY_INTF_SEL_RGMII
  dt-bindings: net: nxp,s32-dwmac: Use the GPR syscon
  dts: s32g: Add GPR syscon region

 .../bindings/net/nxp,s32-dwmac.yaml           | 13 +++++++++++
 arch/arm64/boot/dts/freescale/s32g2.dtsi      |  6 +++++
 arch/arm64/boot/dts/freescale/s32g3.dtsi      |  6 +++++
 .../net/ethernet/stmicro/stmmac/dwmac-s32.c   | 23 +++++++++++++++----
 4 files changed, 43 insertions(+), 5 deletions(-)

-- 
2.51.0

[PATCH v4 2/3] dt-bindings: net: nxp,s32-dwmac: Use the GPR syscon

[Dan Carpenter]

The S32 chipsets have a GPR region which has a miscellaneous registers
including the GMAC_0_CTRL_STS register.  Originally, this code accessed
that register in a sort of ad-hoc way, but it's cleaner to use a
syscon interface to access these registers.

We still need to maintain the old method of accessing the GMAC register
but using a syscon will let us access other registers more cleanly.

Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
---
v4: Fix the formatting issue Rob pointed out
v3: Better documentation about what GMAC_0_CTRL_STS register does.
v2: Add the vendor prefix to the phandle
    Fix the documentation

 .../devicetree/bindings/net/nxp,s32-dwmac.yaml      | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/nxp,s32-dwmac.yaml b/Documentation/devicetree/bindings/net/nxp,s32-dwmac.yaml
index 2b8b74c5feec..65633b10e49e 100644
--- a/Documentation/devicetree/bindings/net/nxp,s32-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/nxp,s32-dwmac.yaml
@@ -32,6 +32,18 @@ properties:
       - description: Main GMAC registers
       - description: GMAC PHY mode control register
 
+  nxp,phy-sel:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to the GPR syscon node
+          - description: offset of PHY selection register
+    description:
+      This phandle points to the GMAC_0_CTRL_STS register which controls the
+      GMAC_0 configuration options.  The register lets you select the PHY
+      interface and the PHY mode.  It also controls if the FTM_0 or FTM_1
+      FlexTimer Modules connect to GMAC_O.
+
   interrupts:
     maxItems: 1
 
@@ -74,6 +86,7 @@ examples:
         compatible = "nxp,s32g2-dwmac";
         reg = <0x0 0x4033c000 0x0 0x2000>, /* gmac IP */
               <0x0 0x4007c004 0x0 0x4>;    /* GMAC_0_CTRL_STS */
+        nxp,phy-sel = <&gpr 0x4>;
         interrupt-parent = <&gic>;
         interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
         interrupt-names = "macirq";
-- 
2.51.0

[PATCH v4 3/3] dts: s32g: Add GPR syscon region

[Dan Carpenter]

Add the GPR syscon region for the s32 chipset.

Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
---
v4: no change
v3: no change
v2: Remove #address-cells and #size-cells

 arch/arm64/boot/dts/freescale/s32g2.dtsi | 6 ++++++
 arch/arm64/boot/dts/freescale/s32g3.dtsi | 6 ++++++
 2 files changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi
index 51d00dac12de..b954952d962b 100644
--- a/arch/arm64/boot/dts/freescale/s32g2.dtsi
+++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi
@@ -325,6 +325,11 @@ usdhc0-200mhz-grp4 {
 			};
 		};
 
+		gpr: syscon@4007c000 {
+			compatible = "nxp,s32g2-gpr", "syscon";
+			reg = <0x4007c000 0x3000>;
+		};
+
 		ocotp: nvmem@400a4000 {
 			compatible = "nxp,s32g2-ocotp";
 			reg = <0x400a4000 0x400>;
@@ -731,6 +736,7 @@ gmac0: ethernet@4033c000 {
 			compatible = "nxp,s32g2-dwmac";
 			reg = <0x4033c000 0x2000>, /* gmac IP */
 			      <0x4007c004 0x4>;    /* GMAC_0_CTRL_STS */
+			nxp,phy-sel = <&gpr 0x4>;
 			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
diff --git a/arch/arm64/boot/dts/freescale/s32g3.dtsi b/arch/arm64/boot/dts/freescale/s32g3.dtsi
index e314f3c7d61d..be03db737384 100644
--- a/arch/arm64/boot/dts/freescale/s32g3.dtsi
+++ b/arch/arm64/boot/dts/freescale/s32g3.dtsi
@@ -383,6 +383,11 @@ usdhc0-200mhz-grp4 {
 			};
 		};
 
+		gpr: syscon@4007c000 {
+			compatible = "nxp,s32g3-gpr", "syscon";
+			reg = <0x4007c000 0x3000>;
+		};
+
 		ocotp: nvmem@400a4000 {
 			compatible = "nxp,s32g3-ocotp", "nxp,s32g2-ocotp";
 			reg = <0x400a4000 0x400>;
@@ -808,6 +813,7 @@ gmac0: ethernet@4033c000 {
 			compatible = "nxp,s32g2-dwmac";
 			reg = <0x4033c000 0x2000>, /* gmac IP */
 			      <0x4007c004 0x4>;    /* GMAC_0_CTRL_STS */
+			nxp,phy-sel = <&gpr 0x4>;
 			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
-- 
2.51.0

Re: [PATCH v4 2/3] dt-bindings: net: nxp,s32-dwmac: Use the GPR syscon

[Rob Herring (Arm)]

On Fri, 23 Jan 2026 22:51:15 +0300, Dan Carpenter wrote:
> The S32 chipsets have a GPR region which has a miscellaneous registers
> including the GMAC_0_CTRL_STS register.  Originally, this code accessed
> that register in a sort of ad-hoc way, but it's cleaner to use a
> syscon interface to access these registers.
> 
> We still need to maintain the old method of accessing the GMAC register
> but using a syscon will let us access other registers more cleanly.
> 
> Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
> ---
> v4: Fix the formatting issue Rob pointed out
> v3: Better documentation about what GMAC_0_CTRL_STS register does.
> v2: Add the vendor prefix to the phandle
>     Fix the documentation
> 
>  .../devicetree/bindings/net/nxp,s32-dwmac.yaml      | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>