Re: [PATCH 4/9] arm64: dts: qcom: sc8280xp-crd: enable NVMe SSD

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 10/11/2022 11:35, Johan Hovold wrote:
> Enable the NVMe SSD connected to PCIe2.
>
> Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
> ---
>   arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 63 +++++++++++++++++++++++
>   1 file changed, 63 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> index 0801bd8c44fb..fd2bdfd1126b 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> @@ -50,6 +50,20 @@ vreg_edp_bl: regulator-edp-bl {
>   		regulator-boot-on;
>   	};
>   
> +	vreg_nvme: regulator-nvme {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VCC3_SSD";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&tlmm 135 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&nvme_reg_en>;
> +	};
> +
>   	vreg_misc_3p3: regulator-misc-3p3 {
>   		compatible = "regulator-fixed";
>   
> @@ -178,6 +192,25 @@ vreg_l9d: ldo9 {
>   	};
>   };
>   
> +&pcie2a {
> +	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
> +	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> +
> +	vddpe-3v3-supply = <&vreg_nvme>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie2a_default>;
> +
> +	status = "okay";
> +};
> +
> +&pcie2a_phy {
> +	vdda-phy-supply = <&vreg_l6d>;
> +	vdda-pll-supply = <&vreg_l4d>;
> +
> +	status = "okay";
> +};
> +
>   &pmc8280c_lpg {
>   	status = "okay";
>   };
> @@ -393,6 +426,36 @@ reset-pins {
>   		};
>   	};
>   
> +	nvme_reg_en: nvme-reg-en-state {
> +		pins = "gpio135";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	pcie2a_default: pcie2a-default-state {

Aren't they going to be identical for all boards anyway? Maybe there
could be some commonization..


Konrad

> +		clkreq-n-pins {
> +			pins = "gpio142";
> +			function = "pcie2a_clkreq";
> +			drive-strength = <2>;
> +			bias-pull-up;
> +		};
> +
> +		perst-n-pins {
> +			pins = "gpio143";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-down;
> +		};
> +
> +		wake-n-pins {
> +		       pins = "gpio145";
> +		       function = "gpio";
> +		       drive-strength = <2>;
> +		       bias-pull-up;
> +	       };
> +	};
> +
>   	qup0_i2c4_default: qup0-i2c4-default-state {
>   		pins = "gpio171", "gpio172";
>   		function = "qup4";