devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Akash Asthana <akashast@codeaurora.org>
To: satya priya <skakit@codeaurora.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	gregkh@linuxfoundation.org
Cc: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Matthias Kaehlcke <mka@chromium.org>,
	linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, rojay@codeaurora.org,
	msavaliy@qti.qualcomm.com
Subject: Re: [PATCH V2 2/3] arm64: dts: qcom: sc7180: Add sleep pin ctrl for BT uart
Date: Tue, 28 Jul 2020 11:08:40 +0530	[thread overview]
Message-ID: <d47f055c-50e6-9bbb-2ab9-e76ff6aac1c9@codeaurora.org> (raw)
In-Reply-To: <1595563082-2353-3-git-send-email-skakit@codeaurora.org>


On 7/24/2020 9:28 AM, satya priya wrote:
> Add sleep pin ctrl for BT uart, and also change the bias
> configuration to match Bluetooth module.


Reviewed-by: Akash Asthana <akashast@codeaurora.org>

> Signed-off-by: satya priya <skakit@codeaurora.org>
> ---
> Changes in V2:
>   - This patch adds sleep state for BT UART. Newly added in V2.
>
>   arch/arm64/boot/dts/qcom/sc7180-idp.dts | 42 ++++++++++++++++++++++++++++-----
>   1 file changed, 36 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 26cc491..bc919f2 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -469,20 +469,50 @@
>   
>   &qup_uart3_default {
>   	pinconf-cts {
> -		/*
> -		 * Configure a pull-down on 38 (CTS) to match the pull of
> -		 * the Bluetooth module.
> -		 */
> +		/* Configure no pull on 38 (CTS) to match Bluetooth module */
>   		pins = "gpio38";
> +		bias-disable;
> +	};
> +
> +	pinconf-rts {
> +		/* We'll drive 39 (RTS), so configure pull-down */
> +		pins = "gpio39";
> +		drive-strength = <2>;
>   		bias-pull-down;
> +	};
> +
> +	pinconf-tx {
> +		/* We'll drive 40 (TX), so no pull */
> +		pins = "gpio40";
> +		drive-strength = <2>;
> +		bias-disable;
>   		output-high;
>   	};
>   
> +	pinconf-rx {
> +		/*
> +		 * Configure a pull-up on 41 (RX). This is needed to avoid
> +		 * garbage data when the TX pin of the Bluetooth module is
> +		 * in tri-state (module powered off or not driving the
> +		 * signal yet).
> +		 */
> +		pins = "gpio41";
> +		bias-pull-up;
> +	};
> +};
> +
> +&qup_uart3_sleep {
> +	pinconf-cts {
> +		/* Configure no-pull on 38 (CTS) to match Bluetooth module */
> +		pins = "gpio38";
> +		bias-disable;
> +	};
> +
>   	pinconf-rts {
> -		/* We'll drive 39 (RTS), so no pull */
> +		/* We'll drive 39 (RTS), so configure pull-down */
>   		pins = "gpio39";
>   		drive-strength = <2>;
> -		bias-disable;
> +		bias-pull-down;
>   	};
>   
>   	pinconf-tx {

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project


  reply	other threads:[~2020-07-28  5:38 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-24  3:57 [PATCH V2 0/3] Add wakeup support over UART RX satya priya
2020-07-24  3:58 ` [PATCH V2 1/3] arm64: dts: sc7180: " satya priya
2020-07-28  5:36   ` Akash Asthana
2020-07-24  3:58 ` [PATCH V2 2/3] arm64: dts: qcom: sc7180: Add sleep pin ctrl for BT uart satya priya
2020-07-28  5:38   ` Akash Asthana [this message]
2020-08-17 18:01   ` Matthias Kaehlcke
2020-08-17 23:33     ` Matthias Kaehlcke
2020-08-19 13:48       ` skakit
2020-08-19 13:49     ` skakit
2020-08-19 16:13       ` Matthias Kaehlcke
2020-08-20 12:19         ` skakit
2020-08-21 15:59           ` Matthias Kaehlcke
2020-07-24  3:58 ` [PATCH V2 3/3] tty: serial: qcom_geni_serial: Fix the UART wakeup issue satya priya
2020-07-24  8:42   ` Greg KH
2020-07-28  5:40   ` Akash Asthana
2020-08-17 17:42   ` Matthias Kaehlcke
2020-08-19 13:49     ` skakit

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=d47f055c-50e6-9bbb-2ab9-e76ff6aac1c9@codeaurora.org \
    --to=akashast@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mka@chromium.org \
    --cc=msavaliy@qti.qualcomm.com \
    --cc=robh+dt@kernel.org \
    --cc=rojay@codeaurora.org \
    --cc=skakit@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).