* [PATCH v9 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform
2025-09-04 7:48 [PATCH v9 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang
2025-09-04 7:48 ` [PATCH v9 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board Yijie Yang
@ 2025-09-04 7:48 ` Yijie Yang
2025-09-04 13:52 ` Dmitry Baryshkov
2025-09-04 7:48 ` [PATCH v9 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang
2025-09-04 14:17 ` [PATCH v9 0/3] Initial support for Qualcomm Hamoa IOT EVK board Rob Herring (Arm)
3 siblings, 1 reply; 13+ messages in thread
From: Yijie Yang @ 2025-09-04 7:48 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Yijie Yang,
Konrad Dybcio
The HAMOA-IOT-SOM is a compact computing module that integrates a System
on Chip (SoC) — specifically the x1e80100 — along with essential
components optimized for IoT applications. It is designed to be mounted on
carrier boards, enabling the development of complete embedded systems.
This change enables the following components:
- Regulators on the SOM
- Reserved memory regions
- PCIe6a and its PHY
- PCIe4 and its PHY
- USB0 through USB6 and their PHYs
- ADSP, CDSP
- WLAN, Bluetooth (M.2 interface)
Written in collaboration with Yingying Tang (PCIe4 and WLAN)
<quic_yintang@quicinc.com>.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 609 ++++++++++++++++++++++++++++
1 file changed, 609 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
new file mode 100644
index 000000000000..5facc5544c3d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
@@ -0,0 +1,609 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include "x1e80100.dtsi"
+#include "x1e80100-pmics.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+/ {
+ compatible = "hamoa-iot-som", "qcom,x1e80100";
+
+ reserved-memory {
+ linux,cma {
+ compatible = "shared-dma-pool";
+ size = <0x0 0x8000000>;
+ reusable;
+ linux,cma-default;
+ };
+ };
+};
+
+&apps_rsc {
+ /* PMC8380C_B */
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob2>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l12-supply = <&vreg_s5j_1p2>;
+ vdd-l15-supply = <&vreg_s4c_1p8>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4b_1p8: ldo4 {
+ regulator-name = "vreg_l4b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p0: ldo5 {
+ regulator-name = "vreg_l5b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_2p8: ldo7 {
+ regulator-name = "vreg_l7b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_3p0: ldo8 {
+ regulator-name = "vreg_l8b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10b_1p8: ldo10 {
+ regulator-name = "vreg_l10b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p2: ldo12 {
+ regulator-name = "vreg_l12b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p0: ldo14 {
+ regulator-name = "vreg_l14b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l16b_2p9: ldo16 {
+ regulator-name = "vreg_l16b_2p9";
+ regulator-min-microvolt = <2912000>;
+ regulator-max-microvolt = <2912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /* PMC8380VE_C */
+ regulators-1 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-l1-supply = <&vreg_s5j_1p2>;
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s4c_1p8: smps4 {
+ regulator-name = "vreg_s4c_1p8";
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p2: ldo1 {
+ regulator-name = "vreg_l1c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c_0p8: ldo2 {
+ regulator-name = "vreg_l2c_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_0p8: ldo3 {
+ regulator-name = "vreg_l3c_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /* PMC8380_D */
+ regulators-2 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-supply = <&vreg_s1f_0p7>;
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s4c_1p8>;
+ vdd-s1-supply = <&vph_pwr>;
+
+ vreg_l1d_0p8: ldo1 {
+ regulator-name = "vreg_l1d_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2d_0p9: ldo2 {
+ regulator-name = "vreg_l2d_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3d_1p8: ldo3 {
+ regulator-name = "vreg_l3d_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /* PMC8380_E */
+ regulators-3 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s5j_1p2>;
+
+ vreg_l2e_0p8: ldo2 {
+ regulator-name = "vreg_l2e_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /* PMC8380_F */
+ regulators-4 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-l1-supply = <&vreg_s5j_1p2>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s5j_1p2>;
+ vdd-s1-supply = <&vph_pwr>;
+
+ vreg_s1f_0p7: smps1 {
+ regulator-name = "vreg_s1f_0p7";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_1p0: ldo1 {
+ regulator-name = "vreg_l1f_1p0";
+ regulator-min-microvolt = <1024000>;
+ regulator-max-microvolt = <1024000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_1p0: ldo2 {
+ regulator-name = "vreg_l2f_1p0";
+ regulator-min-microvolt = <1024000>;
+ regulator-max-microvolt = <1024000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_1p0: ldo3 {
+ regulator-name = "vreg_l3f_1p0";
+ regulator-min-microvolt = <1024000>;
+ regulator-max-microvolt = <1024000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /* PMC8380VE_I */
+ regulators-6 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "i";
+
+ vdd-l1-supply = <&vreg_s4c_1p8>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+
+ vreg_s1i_0p9: smps1 {
+ regulator-name = "vreg_s1i_0p9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2i_1p0: smps2 {
+ regulator-name = "vreg_s2i_1p0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1i_1p8: ldo1 {
+ regulator-name = "vreg_l1i_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2i_1p2: ldo2 {
+ regulator-name = "vreg_l2i_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3i_0p8: ldo3 {
+ regulator-name = "vreg_l3i_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /* PMC8380VE_J */
+ regulators-7 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "j";
+
+ vdd-l1-supply = <&vreg_s1f_0p7>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s5-supply = <&vph_pwr>;
+
+ vreg_s5j_1p2: smps5 {
+ regulator-name = "vreg_s5j_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1j_0p8: ldo1 {
+ regulator-name = "vreg_l1j_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2j_1p2: ldo2 {
+ regulator-name = "vreg_l2j_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1256000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3j_0p8: ldo3 {
+ regulator-name = "vreg_l3j_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&pcie4 {
+ perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l3i_0p8>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&pcie6a {
+ perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie6a_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie6a_phy {
+ vdda-phy-supply = <&vreg_l1d_0p8>;
+ vdda-pll-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&qupv3_0 {
+ status = "okay";
+};
+
+&qupv3_1 {
+ status = "okay";
+};
+
+&qupv3_2 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/x1e80100/adsp.mbn",
+ "qcom/x1e80100/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/x1e80100/cdsp.mbn",
+ "qcom/x1e80100/cdsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&tlmm {
+ gpio-reserved-ranges = <34 2>, /* TPM LP & INT */
+ <44 4>; /* SPI (TPM) */
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio147";
+ function = "pcie4_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio146";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie6a_default: pcie6a-default-state {
+ clkreq-n-pins {
+ pins = "gpio153";
+ function = "pcie6a_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio152";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio154";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+
+ };
+ };
+};
+
+&usb_1_ss0 {
+ status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_ss0_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+ vdda-phy-supply = <&vreg_l2j_1p2>;
+ vdda-pll-supply = <&vreg_l1j_0p8>;
+
+ status = "okay";
+};
+
+&usb_1_ss1 {
+ status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_ss1_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+ vdda-phy-supply = <&vreg_l2j_1p2>;
+ vdda-pll-supply = <&vreg_l2d_0p9>;
+
+ status = "okay";
+};
+
+&usb_1_ss2 {
+ status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_ss2_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&usb_1_ss2_qmpphy {
+ vdda-phy-supply = <&vreg_l2j_1p2>;
+ vdda-pll-supply = <&vreg_l2d_0p9>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_2_hsphy {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp {
+ status = "okay";
+};
+
+&usb_mp_hsphy0 {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_hsphy1 {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3c_0p8>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3c_0p8>;
+
+ status = "okay";
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v9 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board
2025-09-04 7:48 [PATCH v9 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang
2025-09-04 7:48 ` [PATCH v9 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board Yijie Yang
2025-09-04 7:48 ` [PATCH v9 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform Yijie Yang
@ 2025-09-04 7:48 ` Yijie Yang
2025-09-04 13:58 ` Dmitry Baryshkov
2025-09-04 15:15 ` Krzysztof Kozlowski
2025-09-04 14:17 ` [PATCH v9 0/3] Initial support for Qualcomm Hamoa IOT EVK board Rob Herring (Arm)
3 siblings, 2 replies; 13+ messages in thread
From: Yijie Yang @ 2025-09-04 7:48 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Yijie Yang
The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of
the Hamoa IoT SoM and a carrier board. Together, they form a complete
embedded system capable of booting to UART.
This change enables the following peripherals on the carrier board:
- UART
- On-board regulators
- USB Type-C mux
- Pinctrl
- Embedded USB (EUSB) repeaters
- NVMe
- pmic-glink
- USB DisplayPorts
- Bluetooth
- Graphic
- Audio
Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>,
Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth)
<quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts)
<quic_yongmou@quicinc.com>.
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1248 ++++++++++++++++++++++++++++
2 files changed, 1249 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 94a84770b080..5e19535ad63d 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq5018-tplink-archer-ax55-v1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq5332-rdp441.dtb
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
new file mode 100644
index 000000000000..ad72af870496
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -0,0 +1,1248 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include "hamoa-iot-som.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Hamoa IoT EVK";
+ compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100";
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart21;
+ serial1 = &uart14;
+ };
+
+ wcd938x: audio-codec {
+ compatible = "qcom,wcd9385-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000
+ 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ vdd-buck-supply = <&vreg_l15b_1p8>;
+ vdd-rxtx-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l15b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ #sound-dai-cells = <1>;
+ };
+
+ chosen {
+ stdout-path = "serial0: 115200n8";
+ };
+
+ pmic-glink {
+ compatible = "qcom,x1e80100-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+ <&tlmm 123 GPIO_ACTIVE_HIGH>,
+ <&tlmm 125 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss0_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss0_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss0_sbu: endpoint {
+ remote-endpoint = <&usb_1_ss0_sbu_mux>;
+ };
+ };
+ };
+ };
+
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss1_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss1_ss_in: endpoint {
+ remote-endpoint = <&retimer_ss1_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss1_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss1_con_sbu_out>;
+ };
+ };
+ };
+ };
+
+ connector@2 {
+ compatible = "usb-c-connector";
+ reg = <2>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss2_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss2_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss2_ss_in: endpoint {
+ remote-endpoint = <&retimer_ss2_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss2_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss2_con_sbu_out>;
+ };
+ };
+ };
+ };
+ };
+
+ vreg_edp_3p3: regulator-edp-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_EDP_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&edp_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_nvme: regulator-nvme {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_NVME_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ /* Left unused as the retimer is not used on this board. */
+ vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_1P15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb0_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb0_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_1P15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb1_pwr_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb1_pwr_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb1_pwr_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr2_1p15: regulator-rtmr2-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR2_1P15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&tlmm 189 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb2_pwr_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr2_1p8: regulator-rtmr2-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR2_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 126 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb2_pwr_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr2_3p3: regulator-rtmr2-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR2_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 187 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&usb2_pwr_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /*
+ * TODO: These two regulators are actually part of the removable M.2
+ * card and not the CRD mainboard. Need to describe this differently.
+ * Functionally it works correctly, because all we need to do is to
+ * turn on the actual 3.3V supply above.
+ */
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_1p9: regulator-wcn-1p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_1P9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-always-on;
+ };
+
+ vreg_wwan: regulator-wwan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDX_VPH_PWR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 221 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wwan_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ sound {
+ compatible = "qcom,x1e80100-sndcard";
+ model = "X1E80100-EVK";
+ audio-routing = "WooferLeft IN",
+ "WSA WSA_SPK1 OUT",
+ "TweeterLeft IN",
+ "WSA WSA_SPK2 OUT",
+ "WooferRight IN",
+ "WSA2 WSA_SPK2 OUT",
+ "TweeterRight IN",
+ "WSA2 WSA_SPK2 OUT",
+ "IN1_HPHL",
+ "HPHL_OUT",
+ "IN2_HPHR",
+ "HPHR_OUT",
+ "AMIC2",
+ "MIC BIAS2",
+ "VA DMIC0",
+ "MIC BIAS3",
+ "VA DMIC1",
+ "MIC BIAS3",
+ "VA DMIC2",
+ "MIC BIAS1",
+ "VA DMIC3",
+ "MIC BIAS1",
+ "VA DMIC0",
+ "VA MIC BIAS3",
+ "VA DMIC1",
+ "VA MIC BIAS3",
+ "VA DMIC2",
+ "VA MIC BIAS1",
+ "VA DMIC3",
+ "VA MIC BIAS1",
+ "TX SWR_INPUT1",
+ "ADC2_OUTPUT";
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ codec {
+ sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ codec {
+ sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ codec {
+ sound-dai = <&left_woofer>,
+ <&left_tweeter>,
+ <&swr0 0>,
+ <&lpass_wsamacro 0>,
+ <&right_woofer>,
+ <&right_tweeter>,
+ <&swr3 0>,
+ <&lpass_wsa2macro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ codec {
+ sound-dai = <&lpass_vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
+ usb-1-ss0-sbu-mux {
+ compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb_1_ss0_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb_1_ss0_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_sbu>;
+ };
+ };
+ };
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ vdd-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_wcn_0p95>;
+ vdddig-supply = <&vreg_wcn_0p95>;
+ vddrfa1p2-supply = <&vreg_wcn_1p9>;
+ vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_bt_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ typec-mux@8 {
+ compatible = "parade,ps8830";
+ reg = <0x08>;
+
+ clocks = <&rpmhcc RPMH_RF_CLK5>;
+
+ vdd-supply = <&vreg_rtmr2_1p15>;
+ vdd33-supply = <&vreg_rtmr2_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr2_3p3>;
+ vddar-supply = <&vreg_rtmr2_1p15>;
+ vddat-supply = <&vreg_rtmr2_1p15>;
+ vddio-supply = <&vreg_rtmr2_1p8>;
+
+ reset-gpios = <&tlmm 185 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&rtmr2_default>;
+ pinctrl-names = "default";
+
+ orientation-switch;
+ retimer-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss2_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss2_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss2_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss2_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss2_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss2_con_sbu_in>;
+ };
+ };
+ };
+ };
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eusb3_repeater: redriver@47 {
+ compatible = "nxp,ptn3222";
+ reg = <0x47>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb3_reset_n>;
+ pinctrl-names = "default";
+ };
+
+ eusb5_repeater: redriver@43 {
+ compatible = "nxp,ptn3222";
+ reg = <0x43>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb5_reset_n>;
+ pinctrl-names = "default";
+ };
+
+ eusb6_repeater: redriver@4f {
+ compatible = "nxp,ptn3222";
+ reg = <0x4f>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb6_reset_n>;
+ pinctrl-names = "default";
+ };
+};
+
+&i2c7 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ typec-mux@8 {
+ compatible = "parade,ps8830";
+ reg = <0x8>;
+
+ clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+ vdd-supply = <&vreg_rtmr1_1p15>;
+ vdd33-supply = <&vreg_rtmr1_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+ vddar-supply = <&vreg_rtmr1_1p15>;
+ vddat-supply = <&vreg_rtmr1_1p15>;
+ vddio-supply = <&vreg_rtmr1_1p8>;
+
+ reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&rtmr1_default>;
+ pinctrl-names = "default";
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss1_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss1_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss1_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+ };
+ };
+ };
+ };
+};
+
+&lpass_tlmm {
+ spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ spkr_23_sd_n_active: spkr-23-sd-n-active-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&lpass_vamacro {
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+ pinctrl-names = "default";
+
+ vdd-micb-supply = <&vreg_l1b_1p8>;
+ qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+ status = "okay";
+};
+
+&mdss_dp1_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2 {
+ status = "okay";
+};
+
+&mdss_dp2_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+ /delete-property/ #sound-dai-cells;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+ power-supply = <&vreg_edp_3p3>;
+
+ port {
+ edp_panel_in: endpoint {
+ remote-endpoint = <&mdss_dp3_out>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dp3_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_dp3_phy {
+ vdda-phy-supply = <&vreg_l3j_0p8>;
+ vdda-pll-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&pcie6a {
+ vddpe-3v3-supply = <&vreg_nvme>;
+};
+
+&pm8550_gpios {
+ rtmr0_default: rtmr0-reset-n-active-state {
+ pins = "gpio10";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+
+ usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+ pins = "gpio11";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+};
+
+&pm8550ve_9_gpios {
+ usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+};
+
+&pmc8380_5_gpios {
+ usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ bias-disable;
+ input-disable;
+ output-enable;
+ };
+};
+
+&smb2360_0 {
+ status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+ status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&smb2360_2 {
+ status = "okay";
+};
+
+&smb2360_2_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l8b_3p0>;
+};
+
+&swr0 {
+ status = "okay";
+
+ pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+ pinctrl-names = "default";
+
+ /* WSA8845, Left Woofer */
+ left_woofer: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "WooferLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <1 2 3 7 10 13>;
+ };
+
+ /* WSA8845, Left Tweeter */
+ left_tweeter: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TweeterLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <4 5 6 7 11 13>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ /* WCD9385 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9385 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
+&swr3 {
+ status = "okay";
+
+ pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
+ pinctrl-names = "default";
+
+ /* WSA8845, Right Woofer */
+ right_woofer: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "WooferRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <1 2 3 7 10 13>;
+ };
+
+ /* WSA8845, Right Tweeter */
+ right_tweeter: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TweeterRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <4 5 6 7 11 13>;
+ };
+};
+
+&tlmm {
+ edp_reg_en: edp-reg-en-state {
+ pins = "gpio70";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ eusb3_reset_n: eusb3-reset-n-state {
+ pins = "gpio6";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ eusb5_reset_n: eusb5-reset-n-state {
+ pins = "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ output-low;
+ };
+
+ eusb6_reset_n: eusb6-reset-n-state {
+ pins = "gpio184";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ output-low;
+ };
+
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rtmr1_default: rtmr1-reset-n-active-state {
+ pins = "gpio176";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rtmr2_default: rtmr2-reset-n-active-state {
+ pins = "gpio185";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state {
+ pins = "gpio188";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state {
+ pins = "gpio175";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state {
+ pins = "gpio186";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb2_pwr_1p15_reg_en: usb2-pwr-1p15-reg-en-state {
+ pins = "gpio189";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb2_pwr_1p8_reg_en: usb2-pwr-1p8-reg-en-state {
+ pins = "gpio126";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state {
+ pins = "gpio187";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
+ mode-pins {
+ pins = "gpio166";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-high;
+ };
+
+ oe-n-pins {
+ pins = "gpio168";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ sel-pins {
+ pins = "gpio167";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ };
+
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio191";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ wcn_bt_en: wcn-bt-en-state {
+ pins = "gpio116";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wwan_sw_en: wwan-sw-en-state {
+ pins = "gpio221";
+ function = "gpio";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio214";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ /* Switches USB signal routing between the USB connector and the Wi-Fi card. */
+ wcn_usb_sw_n: wcn-usb-sw-n-state {
+ pins = "gpio225";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+ max-speed = <3200000>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ };
+};
+
+&uart21 {
+ compatible = "qcom,geni-debug-uart";
+
+ status = "okay";
+};
+
+&usb_1_ss0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_hsphy {
+ phys = <&smb2360_0_eusb2_repeater>;
+};
+
+&usb_1_ss0_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_hsphy {
+ phys = <&smb2360_1_eusb2_repeater>;
+};
+
+&usb_1_ss1_qmpphy_out {
+ remote-endpoint = <&retimer_ss1_ss_in>;
+};
+
+&usb_1_ss2_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss2_hs_in>;
+};
+
+&usb_1_ss2_hsphy {
+ phys = <&smb2360_2_eusb2_repeater>;
+};
+
+&usb_1_ss2_qmpphy_out {
+ remote-endpoint = <&retimer_ss2_ss_in>;
+};
+
+&usb_2_hsphy {
+ phys = <&eusb5_repeater>;
+
+ pinctrl-0 = <&wcn_usb_sw_n>;
+ pinctrl-names = "default";
+};
+
+&usb_mp_hsphy0 {
+ phys = <&eusb6_repeater>;
+};
+
+&usb_mp_hsphy1 {
+ phys = <&eusb3_repeater>;
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v9 0/3] Initial support for Qualcomm Hamoa IOT EVK board
2025-09-04 7:48 [PATCH v9 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang
` (2 preceding siblings ...)
2025-09-04 7:48 ` [PATCH v9 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang
@ 2025-09-04 14:17 ` Rob Herring (Arm)
3 siblings, 0 replies; 13+ messages in thread
From: Rob Herring (Arm) @ 2025-09-04 14:17 UTC (permalink / raw)
To: Yijie Yang
Cc: Krzysztof Kozlowski, Bjorn Andersson, linux-arm-msm, Conor Dooley,
devicetree, Krzysztof Kozlowski, Konrad Dybcio, linux-kernel,
Konrad Dybcio
On Thu, 04 Sep 2025 15:48:31 +0800, Yijie Yang wrote:
> Introduce the device tree, DT bindings, and driver modifications required
> to bring up the HAMOA-IOT-EVK evaluation board—based on the X1E80100 SoC—to
> a UART shell.
> This patch set focuses on two key hardware components: the HAMOA-IOT-SOM
> and the HAMOA-IOT-EVK carrier board.
> The HAMOA-IOT-SOM is a compact System on Module that integrates the SoC,
> GPIOs, and PMICs. It is designed to be modular and can be paired with
> various carrier boards to support different use cases.
> The HAMOA-IOT-EVK is one such carrier board, designed for IoT scenarios.
> It provides essential peripherals such as UART, on-board PMICs, and
> USB-related components.
> Together, these components form a flexible and scalable platform, and this
> patch set enables their initial bring-up through proper device tree
> configuration and driver support.
>
> Qualcomm SoCs often have multiple product variants, each identified by a
> different SoC ID. For instance, the x1e80100 SoC has closely related
> variants such as x1e78100 and x1e001de. This diversity in SoC identifiers
> can lead to confusion and unnecessary maintenance complexity in the device
> tree and related subsystems.
> To address this, code names offer a more consistent and project-agnostic
> way to represent SoC families. They tend to remain stable across
> development efforts.
> This patch series introduces "hamoa" as the codename for the x1e80100 SoC.
> Going forward, all x1e80100-related variants—including x1e81000 and others
> in the same family—will be represented under the "hamoa" designation in the
> device tree.
> This improves readability, streamlines future maintenance, and aligns with
> common naming practices across Qualcomm-based platforms.
>
> Features added and enabled:
> - UART
> - On-board regulators
> - Regulators on the SOM
> - PMIC GLINK
> - USB0 through USB6 and their PHYs
> - Embedded USB (eUSB) repeaters
> - USB Type-C mux
> - PCIe6a and its PHY
> - PCIe4 and its PHY
> - Reserved memory regions
> - Pinctrl
> - NVMe
> - ADSP, CDSP
> - WLAN, Bluetooth (M.2 interface)
> - USB DisplayPort
> - Graphic
> - Audio
>
> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
> ---
> Changes in v9:
> - Sort the nodes within the root node in alphabetical order.
> - Add WLAN control pin to the PMU.
> - Link to v8: https://lore.kernel.org/r/20250828-hamoa_initial-v8-0-c9d173072a5c@oss.qualcomm.com
>
> Changes in v8:
> - Change the style of how collaborators are listed.
> - Link to v7: https://lore.kernel.org/r/20250827-hamoa_initial-v7-0-f9b81d564bb2@oss.qualcomm.com
>
> Changes in v7:
> - Configure the EDP regulator to boot-on.
> - Change back to a year‑less copyright statement.
> - Update base commit.
> - Link to v6: https://lore.kernel.org/r/20250821-hamoa_initial-v6-0-72e4e01a55d0@oss.qualcomm.com
>
> Changes in v6:
> - Restore the full change log for each revision.
> - Merge the changes related to Audio and Graphics into the patch series.
> - Link to v5: https://lore.kernel.org/r/20250814-hamoa_initial-v5-0-817a9c6e8d47@oss.qualcomm.com
>
> Changes in v5:
> - Update base commit.
> - Drop an already merged patch:
> https://lore.kernel.org/all/20250804-hamoa_initial-v4-2-19edbb28677b@oss.qualcomm.com/
> - Link to v4: https://lore.kernel.org/r/20250804-hamoa_initial-v4-0-19edbb28677b@oss.qualcomm.com
>
> Changes in v4:
> - Update commit messages.
> - Update base commit.
> - Update the format of the node mdss_dp3_out.
> - Add comments to clarify certain nodes.
> - Update the configuration of regulator-wcn-3p3 from regulator-boot-on to regulator-always-on.
> - Link to v3: https://lore.kernel.org/r/20250729-hamoa_initial-v3-0-806e092789dc@oss.qualcomm.com
>
> Changes in v3:
> - Add compatible string and dt-bindings for SOM.
> - Restore PMU-related regulators to comply with dt-binding rules and enable kernel-level power management.
> - Adjust commit description accordingly.
> - Link to v2: https://lore.kernel.org/r/20250724-hamoa_initial-v2-0-91b00c882d11@oss.qualcomm.com
>
> Changes in v2:
> - Merge the compatible rules and remove the compatible string map.
> - Align the ADSP and CDSP firmware paths with other x1e80100 platforms.
> - Remove the regulators on the M.2 card, as well as those managed by UEFI on this board.
> - Merge another patch series that enables USB DisplayPort functionality on this platform: https://lore.kernel.org/all/20250723-x1e-evk-dp-v1-1-be76ce53b9b8@quicinc.com/
> - Link to v1: https://lore.kernel.org/r/20250716-hamoa_initial-v1-0-f6f5d0f9a163@oss.qualcomm.com
>
> ---
> Yijie Yang (3):
> dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board
> arm64: dts: qcom: Add HAMOA-IOT-SOM platform
> arm64: dts: qcom: Add base HAMOA-IOT-EVK board
>
> Documentation/devicetree/bindings/arm/qcom.yaml | 6 +
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1248 +++++++++++++++++++++++
> arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 609 +++++++++++
> 4 files changed, 1864 insertions(+)
> ---
> base-commit: b899981540841e409e496083921f2e5c4c209925
> change-id: 20250604-hamoa_initial-0cd7036d7271
>
> Best regards,
> --
> Yijie Yang <yijie.yang@oss.qualcomm.com>
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
This patch series was applied (using b4) to base:
Base: using specified base-commit b899981540841e409e496083921f2e5c4c209925
If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)
New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20250904-hamoa_initial-v9-0-d73213fa7542@oss.qualcomm.com:
arch/arm64/boot/dts/qcom/hamoa-iot-evk.dtb: chosen: stdout-path:0: 'serial0: 115200n8' does not match '^[a-zA-Z0-9@/,+\-._]*(:[0-9]*[noe]?[78]?[r]?)?$'
from schema $id: http://devicetree.org/schemas/chosen.yaml#
^ permalink raw reply [flat|nested] 13+ messages in thread