Re: [PATCH 2/9] riscv: dts: starfive: jh7110: add dc&hdmi controller node

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 02/06/2023 09:40, Keith Zhao wrote:
> Add the dc controller and hdmi node for the Starfive JH7110 SoC.
> 
> Signed-off-by: Keith Zhao <keith.zhao@starfivetech.com>
> ---
>  .../jh7110-starfive-visionfive-2.dtsi         | 87 +++++++++++++++++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 46 ++++++++++
>  2 files changed, 133 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index 1155b97b593d..8dc6c8a15c59 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -31,6 +31,21 @@ memory@40000000 {
>  		reg = <0x0 0x40000000 0x1 0x0>;
>  	};
>  
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		linux,cma {
> +			compatible = "shared-dma-pool";
> +			reusable;
> +			size = <0x0 0x20000000>;
> +			alignment = <0x0 0x1000>;
> +			alloc-ranges = <0x0 0x80000000 0x0 0x20000000>;
> +			linux,cma-default;
> +		};
> +	};
> +
>  	gpio-restart {
>  		compatible = "gpio-restart";
>  		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
> @@ -214,6 +229,41 @@ GPOEN_DISABLE,
>  			slew-rate = <0>;
>  		};
>  	};
> +
> +	hdmi_pins: hdmi-0 {
> +		hdmi-scl-pins {
> +			pinmux = <GPIOMUX(0, GPOUT_SYS_HDMI_DDC_SCL,
> +					     GPOEN_SYS_HDMI_DDC_SCL,
> +					     GPI_SYS_HDMI_DDC_SCL)>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		hdmi-sda-pins {
> +			pinmux = <GPIOMUX(1, GPOUT_SYS_HDMI_DDC_SDA,
> +					     GPOEN_SYS_HDMI_DDC_SDA,
> +					     GPI_SYS_HDMI_DDC_SDA)>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		hdmi-cec-pins {
> +			pinmux = <GPIOMUX(14, GPOUT_SYS_HDMI_CEC_SDA,
> +					     GPOEN_SYS_HDMI_CEC_SDA,
> +					     GPI_SYS_HDMI_CEC_SDA)>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		hdmi-hpd-pins {
> +			pinmux = <GPIOMUX(15, GPOUT_HIGH,
> +					     GPOEN_ENABLE,
> +					     GPI_SYS_HDMI_HPD)>;
> +			input-enable;
> +			bias-disable; /* external pull-up */
> +		};
> +	};
> +
>  };
>  
>  &uart0 {
> @@ -221,3 +271,40 @@ &uart0 {
>  	pinctrl-0 = <&uart0_pins>;
>  	status = "okay";
>  };
> +
> +&voutcrg {
> +	status = "okay";
> +};
> +
> +&display {
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hdmi_pins>;
> +
> +	hdmi_in: port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		hdmi_input: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&dc_out_dpi0>;

This does not make any sense. You wrote in bindings that this is display
output, but you call it HDMI input. If this is input, where is your output?

> +		};
> +	};
> +};
> +
> +&dc8200 {
> +	status = "okay";
> +
> +	dc_out: port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		dc_out_dpi0: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&hdmi_input>;
> +		};
> +

Stray blank line.

> +	};
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 9acb5fb1716d..66be6e65a066 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -249,6 +249,11 @@ tdm_ext: tdm-ext-clock {
>  		#clock-cells = <0>;
>  	};
>  
> +	display: display-subsystem {
> +		compatible = "verisilicon,display-subsystem";

Drop fake nodes which do not represent hardware. Instead, DTS and
bindings should describe real hardware.


> +		ports = <&dc_out>;
> +	};
> +
>  	soc {
>  		compatible = "simple-bus";
>  		interrupt-parent = <&plic>;
> @@ -570,5 +575,46 @@ voutcrg: clock-controller@295c0000 {
>  			#reset-cells = <1>;
>  			power-domains = <&pwrc JH7110_PD_VOUT>;
>  		};
> +
> +		dc8200: dc8200@29400000 {

Node names should be generic. See also explanation and list of examples
in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

> +			compatible = "verisilicon,dc8200";
> +			reg = <0x0 0x29400000 0x0 0x100>,
> +			      <0x0 0x29400800 0x0 0x2000>,
> +			      <0x0 0x295B0000 0x0 0x90>;
> +			interrupts = <95>;
> +			clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_DISP_AXI>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_PIX0>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_PIX1>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_AXI>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_CORE>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_AHB>,
> +				<&hdmitx0_pixelclk>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_PIX>;
> +			clock-names = "clk_vout_noc_disp",
> +				"clk_vout_pix0","clk_vout_pix1",

Fix alignment

> +				"clk_vout_axi","clk_vout_core",
> +				"clk_vout_vout_ahb","hdmitx0_pixel",
> +				"clk_vout_dc8200";
> +			resets = <&voutcrg JH7110_VOUTRST_DC8200_AXI>,
> +				 <&voutcrg JH7110_VOUTRST_DC8200_AHB>,
> +				 <&voutcrg JH7110_VOUTRST_DC8200_CORE>;
> +			reset-names = "rst_vout_axi","rst_vout_ahb",
> +						"rst_vout_core";

Fix alignment.



Best regards,
Krzysztof