* [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support
@ 2025-01-16 23:21 Sean Anderson
2025-01-16 23:21 ` [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus Sean Anderson
` (2 more replies)
0 siblings, 3 replies; 14+ messages in thread
From: Sean Anderson @ 2025-01-16 23:21 UTC (permalink / raw)
To: Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Sean Anderson, Conor Dooley, Krzysztof Kozlowski,
Rob Herring, devicetree
As discussed in patches 1 and FIXME, this device really has two SPI
busses. Split the existing "merged" bus in twain, and add support for
GPIO chipselects.
This series depends on [1, 2].
[1] https://lore.kernel.org/linux-spi/20250116224130.2684544-1-sean.anderson@linux.dev/T/#t
[2] https://lore.kernel.org/linux-spi/20250116225521.2688224-1-sean.anderson@linux.dev/T/#t
Sean Anderson (7):
dt-bindings: spi: zynqmp-qspi: Split the bus
spi: zynqmp-gqspi: Pass speed/mode directly to config_op
spi: zynqmp-gqspi: Configure SPI mode dynamically
spi: zynqmp-gqspi: Refactor out controller initialization
spi: zynqmp-gqspi: Split the bus
spi: zynqmp-gqspi: Support GPIO chip selects
ARM64: xilinx: zynqmp: Convert to split QSPI bus
.../bindings/spi/spi-zynqmp-qspi.yaml | 43 ++-
.../boot/dts/xilinx/zynqmp-sm-k26-revA.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zc1232-revA.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zc1254-revA.dts | 5 +-
.../dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 5 +-
.../dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 5 +-
.../boot/dts/xilinx/zynqmp-zcu1275-revA.dts | 5 +-
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 15 +-
drivers/spi/spi-zynqmp-gqspi.c | 328 ++++++++++++++----
14 files changed, 359 insertions(+), 82 deletions(-)
--
2.35.1.1320.gc452695387.dirty
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-16 23:21 [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
@ 2025-01-16 23:21 ` Sean Anderson
2025-01-22 0:16 ` David Lechner
2025-01-16 23:21 ` [PATCH 7/7] ARM64: xilinx: zynqmp: Convert to split QSPI bus Sean Anderson
2025-01-16 23:24 ` [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
2 siblings, 1 reply; 14+ messages in thread
From: Sean Anderson @ 2025-01-16 23:21 UTC (permalink / raw)
To: Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Sean Anderson, Conor Dooley, Krzysztof Kozlowski,
Rob Herring, devicetree
This device supports two separate SPI busses: "lower" (SPI0) and "upper"
(SPI1). Each SPI bus has separate clock and data lines, as well as a
hardware-controlled chip select. The current binding does not model this
situation. It exposes one bus, where CS 0 uses the lower bus and the
lower chip select, and CS 1 uses the upper bus and the upper chip
select. It is not possible to use the upper chip select with the lower
bus (or vice versa). GPIO chip selects are unsupported, and there would
be no way to specify which bus to use if they were.
Split the "merged" bus into an upper and lower bus, each with their own
subnodes.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
---
.../bindings/spi/spi-zynqmp-qspi.yaml | 43 +++++++++++++++++--
1 file changed, 40 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml
index 901e15fcce2d..12c547c4f1ba 100644
--- a/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml
+++ b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml
@@ -39,6 +39,18 @@ properties:
resets:
maxItems: 1
+ spi-lower:
+ type: object
+ $ref: spi-controller.yaml#
+ unevaluatedProperties: false
+ description: The "lower" bus (SPI0). On the ZynqMP this uses MIO pins 0-5.
+
+ spi-upper:
+ type: object
+ $ref: spi-controller.yaml#
+ unevaluatedProperties: false
+ description: The "upper" bus (SPI1). On the ZynqMP this uses MIO pins 7-12.
+
required:
- compatible
- reg
@@ -50,8 +62,6 @@ required:
unevaluatedProperties: false
allOf:
- - $ref: spi-controller.yaml#
-
- if:
properties:
compatible:
@@ -75,7 +85,7 @@ examples:
#address-cells = <2>;
#size-cells = <2>;
- qspi: spi@ff0f0000 {
+ qspi: spi-controller@ff0f0000 {
compatible = "xlnx,zynqmp-qspi-1.0";
clocks = <&zynqmp_clk QSPI_REF>, <&zynqmp_clk LPD_LSBUS>;
clock-names = "ref_clk", "pclk";
@@ -84,5 +94,32 @@ examples:
resets = <&zynqmp_reset ZYNQMP_RESET_QSPI>;
reg = <0x0 0xff0f0000 0x0 0x1000>,
<0x0 0xc0000000 0x0 0x8000000>;
+
+ spi-lower {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ num-cs = <2>;
+ cs-gpios = <0>, <&gpio 5>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ };
+
+ flash@1 {
+ reg = <1>;
+ compatible = "jedec,spi-nor";
+ };
+ };
+
+ spi-upper {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ };
+ };
};
};
--
2.35.1.1320.gc452695387.dirty
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 7/7] ARM64: xilinx: zynqmp: Convert to split QSPI bus
2025-01-16 23:21 [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
2025-01-16 23:21 ` [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus Sean Anderson
@ 2025-01-16 23:21 ` Sean Anderson
2025-01-16 23:24 ` [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
2 siblings, 0 replies; 14+ messages in thread
From: Sean Anderson @ 2025-01-16 23:21 UTC (permalink / raw)
To: Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Sean Anderson, Conor Dooley, Krzysztof Kozlowski,
Rob Herring, devicetree
Convert the ZynqMP devicetrees to use the split QSPI bus binding. This
is pretty simple, since all boards use only CS0.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
---
arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts | 5 ++++-
.../boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 5 ++++-
.../boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 5 ++++-
.../arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts | 5 ++++-
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 15 +++++++++++----
12 files changed, 55 insertions(+), 15 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
index bfa7ea6b9224..64b90de5b4ce 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
@@ -35,7 +35,7 @@ aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
spi1 = &spi0;
spi2 = &spi1;
usb0 = &usb0;
@@ -129,6 +129,9 @@ mux {
&qspi { /* MIO 0-5 - U143 */
status = "okay";
+};
+
+&qspi_lower {
spi_flash: flash@0 { /* MT25QU512A */
compatible = "jedec,spi-nor"; /* 64MB */
reg = <0>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
index 04079d1704f1..8927e0463cf4 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
@@ -19,7 +19,7 @@ / {
aliases {
serial0 = &uart0;
serial1 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
};
chosen {
@@ -39,6 +39,9 @@ &dcc {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
index 3dec57cf18be..da07b58706f0 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
@@ -20,7 +20,7 @@ / {
aliases {
serial0 = &uart0;
serial1 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
};
chosen {
@@ -40,6 +40,9 @@ &dcc {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
index 6aff22d43361..ec570d68a4ae 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -27,7 +27,7 @@ aliases {
mmc1 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
usb0 = &usb0;
};
@@ -354,6 +354,9 @@ &psgtr {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* Micron MT25QU512ABB8ESF */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
index 6ec1d9813973..e1cfdc0db51e 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
@@ -26,7 +26,7 @@ aliases {
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
};
chosen {
@@ -172,6 +172,9 @@ &i2c1 {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index 7e26489a1539..18e323e2aad7 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -31,7 +31,7 @@ aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
usb0 = &usb0;
};
@@ -953,6 +953,9 @@ &psgtr {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
index eb2090673ec1..026053c4116a 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -29,7 +29,7 @@ aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
usb0 = &usb0;
};
@@ -439,6 +439,9 @@ &psgtr {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
index 4694d0a841f1..da56e532dc2b 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -29,7 +29,7 @@ aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
usb0 = &usb0;
};
@@ -451,6 +451,9 @@ &psgtr {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index 7beedd730f94..8dd73b035969 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -31,7 +31,7 @@ aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
usb0 = &usb0;
};
@@ -959,6 +959,9 @@ &psgtr {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index b67ff7ecf3c3..9ed7972c3b4e 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -30,7 +30,7 @@ aliases {
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
usb0 = &usb0;
};
@@ -789,6 +789,9 @@ &psgtr {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts
index a38c2baeba6c..99d007b3bfae 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu1275-revA.dts
@@ -20,7 +20,7 @@ / {
aliases {
serial0 = &uart0;
serial1 = &dcc;
- spi0 = &qspi;
+ spi0 = &qspi_lower;
};
chosen {
@@ -44,6 +44,9 @@ &gpio {
&qspi {
status = "okay";
+};
+
+&qspi_lower {
flash@0 {
compatible = "m25p80", "jedec,spi-nor";
reg = <0x0>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index 5dac0542a48d..470e0b90382f 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -972,21 +972,28 @@ pcie_intc: legacy-interrupt-controller {
};
};
- qspi: spi@ff0f0000 {
+ qspi: spi-controller@ff0f0000 {
bootph-all;
compatible = "xlnx,zynqmp-qspi-1.0";
status = "disabled";
clock-names = "ref_clk", "pclk";
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
interrupt-parent = <&gic>;
- num-cs = <1>;
reg = <0x0 0xff0f0000 0x0 0x1000>,
<0x0 0xc0000000 0x0 0x8000000>;
- #address-cells = <1>;
- #size-cells = <0>;
/* iommus = <&smmu 0x873>; */
power-domains = <&zynqmp_firmware PD_QSPI>;
resets = <&zynqmp_reset ZYNQMP_RESET_QSPI>;
+
+ qspi_lower: spi-lower {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ qspi_upper: spi-upper {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
psgtr: phy@fd400000 {
--
2.35.1.1320.gc452695387.dirty
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support
2025-01-16 23:21 [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
2025-01-16 23:21 ` [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus Sean Anderson
2025-01-16 23:21 ` [PATCH 7/7] ARM64: xilinx: zynqmp: Convert to split QSPI bus Sean Anderson
@ 2025-01-16 23:24 ` Sean Anderson
2 siblings, 0 replies; 14+ messages in thread
From: Sean Anderson @ 2025-01-16 23:24 UTC (permalink / raw)
To: Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree
On 1/16/25 18:21, Sean Anderson wrote:
> As discussed in patches 1 and FIXME, this device really has two SPI
This should be "patches 1 and 5" (oops)
> busses. Split the existing "merged" bus in twain, and add support for
> GPIO chipselects.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-16 23:21 ` [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus Sean Anderson
@ 2025-01-22 0:16 ` David Lechner
2025-01-23 16:24 ` Sean Anderson
0 siblings, 1 reply; 14+ messages in thread
From: David Lechner @ 2025-01-22 0:16 UTC (permalink / raw)
To: Sean Anderson, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 1/16/25 5:21 PM, Sean Anderson wrote:
> This device supports two separate SPI busses:
...
> @@ -84,5 +94,32 @@ examples:
> resets = <&zynqmp_reset ZYNQMP_RESET_QSPI>;
> reg = <0x0 0xff0f0000 0x0 0x1000>,
> <0x0 0xc0000000 0x0 0x8000000>;
> +
> + spi-lower {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + num-cs = <2>;
> + cs-gpios = <0>, <&gpio 5>;
> +
> + flash@0 {
> + reg = <0>;
> + compatible = "jedec,spi-nor";
> + };
> +
> + flash@1 {
> + reg = <1>;
> + compatible = "jedec,spi-nor";
> + };
> + };
> +
> + spi-upper {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash@0 {
> + reg = <0>;
> + compatible = "jedec,spi-nor";
> + };
> + };
> };
> };
In the IIO subsystem, we've been recently working on several "advanced" ADCs
that could use a SPI controller like this. These ADCs have multiple input
channels that perform conversions in parallel and the data for each channel
needs to be read back on a separate serial line (MISO) at the same time. Another
similar case is to have two separate chips, but they share a conversion trigger
and essentially operate as a single composite device rather than two distinct
devices [1]. This would be similar to some ADCs that are daisy-chained where we
consider all of the chips in the chain as a single composite device, but they
would be in parallel rather than chained.
[1]: https://lore.kernel.org/linux-iio/e5e8eba7-2455-488b-a36f-e246844e11fd@baylibre.com/
For those use cases though, as mentioned above, we only have a single device
that would be connected to both buses. So for such a SPI controller with
multiple buses, I was envisioning that instead of adding child nodes for each
of the child buses, that we would do something like add a spi-buses property
to the spi peripheral bindings where you could specify one or more buses that
a device was connected to.
e.g. a device connected to the lower bus would be spi-buses = <0>; one connected
to the upper bus would be spi-buses = <1>; and a device connected to both would
be spi-buses = <0>, <1>;. This would also work for SPI controllers that have
4 or 8 busses.
SPI controllers like these have a striping feature that allows to control both
buses at the same to either mirror the same data on both buses at the same
time when writing, e.g. for configuration or to read and write two different
bytes at the same time. A peripheral driver for device that was connected to
both buses could make use of this feature to craft a single SPI message with
transfers containing (new) parameters that specify which bus to use (one or
both) and, in the case of using both buses, to mirror or stripe the data.
Could we make a single device connected to both buses like this work using
the proposed spi-lower and spi-upper or should we consider a different binding
like the one I suggested?
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-22 0:16 ` David Lechner
@ 2025-01-23 16:24 ` Sean Anderson
2025-01-23 21:59 ` David Lechner
0 siblings, 1 reply; 14+ messages in thread
From: Sean Anderson @ 2025-01-23 16:24 UTC (permalink / raw)
To: David Lechner, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 1/21/25 19:16, David Lechner wrote:
> On 1/16/25 5:21 PM, Sean Anderson wrote:
>> This device supports two separate SPI busses:
>
> ...
>
>> @@ -84,5 +94,32 @@ examples:
>> resets = <&zynqmp_reset ZYNQMP_RESET_QSPI>;
>> reg = <0x0 0xff0f0000 0x0 0x1000>,
>> <0x0 0xc0000000 0x0 0x8000000>;
>> +
>> + spi-lower {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + num-cs = <2>;
>> + cs-gpios = <0>, <&gpio 5>;
>> +
>> + flash@0 {
>> + reg = <0>;
>> + compatible = "jedec,spi-nor";
>> + };
>> +
>> + flash@1 {
>> + reg = <1>;
>> + compatible = "jedec,spi-nor";
>> + };
>> + };
>> +
>> + spi-upper {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + flash@0 {
>> + reg = <0>;
>> + compatible = "jedec,spi-nor";
>> + };
>> + };
>> };
>> };
>
> In the IIO subsystem, we've been recently working on several "advanced" ADCs
> that could use a SPI controller like this. These ADCs have multiple input
> channels that perform conversions in parallel and the data for each channel
> needs to be read back on a separate serial line (MISO) at the same time. Another
> similar case is to have two separate chips, but they share a conversion trigger
> and essentially operate as a single composite device rather than two distinct
> devices [1]. This would be similar to some ADCs that are daisy-chained where we
> consider all of the chips in the chain as a single composite device, but they
> would be in parallel rather than chained.
>
> [1]: https://lore.kernel.org/linux-iio/e5e8eba7-2455-488b-a36f-e246844e11fd@baylibre.com/
>
> For those use cases though, as mentioned above, we only have a single device
> that would be connected to both buses. So for such a SPI controller with
> multiple buses, I was envisioning that instead of adding child nodes for each
> of the child buses, that we would do something like add a spi-buses property
> to the spi peripheral bindings where you could specify one or more buses that
> a device was connected to.
>
> e.g. a device connected to the lower bus would be spi-buses = <0>; one connected
> to the upper bus would be spi-buses = <1>; and a device connected to both would
> be spi-buses = <0>, <1>;. This would also work for SPI controllers that have
> 4 or 8 busses.
>
> SPI controllers like these have a striping feature that allows to control both
> buses at the same to either mirror the same data on both buses at the same
> time when writing, e.g. for configuration or to read and write two different
> bytes at the same time. A peripheral driver for device that was connected to
> both buses could make use of this feature to craft a single SPI message with
> transfers containing (new) parameters that specify which bus to use (one or
> both) and, in the case of using both buses, to mirror or stripe the data.
>
> Could we make a single device connected to both buses like this work using
> the proposed spi-lower and spi-upper or should we consider a different binding
> like the one I suggested?
If you are willing to do the work to rewrite the SPI subsystem to handle
this, then I don't object to it in principle. Using a property would
also help with forwards compatibility. On the other hand, separate
busses are easier to implement since they integrate better with the SPI
subsystem (e.g. you can just call spi_register_controller to create all
the slaves).
There have been some previous patches from Xilinx to handle this
use case [1], but IMO they were pretty hacky. They got this feature
merged into U-Boot and it broke many other boards and took a lot of
cleanup to fix. So I have intentionally only tackled the unsynchronized
use case since that requires no modification to areas outside of this
driver. I don't need the "parallel" use case and I am not interested in
doing the work required to implement it.
--Sean
[1] https://lore.kernel.org/linux-spi/20221017121249.19061-1-amit.kumar-mahapatra@amd.com/
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-23 16:24 ` Sean Anderson
@ 2025-01-23 21:59 ` David Lechner
2025-01-23 22:37 ` Sean Anderson
2025-06-12 23:44 ` Sean Anderson
0 siblings, 2 replies; 14+ messages in thread
From: David Lechner @ 2025-01-23 21:59 UTC (permalink / raw)
To: Sean Anderson, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 1/23/25 10:24 AM, Sean Anderson wrote:
> On 1/21/25 19:16, David Lechner wrote:
>> On 1/16/25 5:21 PM, Sean Anderson wrote:
...
>> Could we make a single device connected to both buses like this work using
>> the proposed spi-lower and spi-upper or should we consider a different binding
>> like the one I suggested?
>
> If you are willing to do the work to rewrite the SPI subsystem to handle
> this, then I don't object to it in principle. Using a property would
> also help with forwards compatibility. On the other hand, separate
> busses are easier to implement since they integrate better with the SPI
> subsystem (e.g. you can just call spi_register_controller to create all
> the slaves).
>
> There have been some previous patches from Xilinx to handle this
> use case [1], but IMO they were pretty hacky. They got this feature
> merged into U-Boot and it broke many other boards and took a lot of
> cleanup to fix. So I have intentionally only tackled the unsynchronized
> use case since that requires no modification to areas outside of this
> driver. I don't need the "parallel" use case and I am not interested in
> doing the work required to implement it.
>
> --Sean
>
> [1] https://lore.kernel.org/linux-spi/20221017121249.19061-1-amit.kumar-mahapatra@amd.com/
Fair enough, and I think it can be done without breaking things like the multi
CS support did.
Here are a couple of patches. Feel free to resubmit them with your series if
they work for you. To make it work with your series, you should just need to
modify the .dts to look like this:
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-buses = <0>; /* lower */
+ };
+
+ flash@1 {
+ reg = <1>;
+ compatible = "jedec,spi-nor";
+ /* also OK to omit property in case of spi-buses = <0>; */
+ };
+
+ flash@2 {
+ reg = <2>;
+ compatible = "jedec,spi-nor";
+ spi-buses = <1>; /* upper */
+ };
Then drop patch "spi: zynqmp-gqspi: Split the bus" of course.
In zynqmp_qspi_probe(), add a line:
ctlr->num_buses = 2;
And in the zynqmp_qspi_transfer_one() function, use spi->buses to select the
correct bus:
xqspi->genfifobus = FIELD_PREP(GQSPI_GENFIFO_BUS_MASK, spi->buses);
I don't have a SPI controller on hand with multiple buses, so I don't have
any patch adding support to a specific controller. But I did build and run this
and hacked in some stuff to the drivers I am working on to make sure it is
working as advertised as best as I could with a single bus.
---
From: David Lechner <dlechner@baylibre.com>
Date: Thu, 23 Jan 2025 15:32:08 -0600
Subject: [PATCH 1/2] spi: dt-bindings: spi-peripheral-props: add spi-buses
property
Add a spi-buses property to the spi-peripheral-props binding to allow
specifying the SPI bus or buses that a peripheral is connected to in
cases where the SPI controller has more than one physical SPI bus.
Signed-off-by: David Lechner <dlechner@baylibre.com>
---
.../devicetree/bindings/spi/spi-peripheral-props.yaml | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml b/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
index 0bb443b8decd..a69d368a8ae6 100644
--- a/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
@@ -88,6 +88,16 @@ properties:
description:
Delay, in microseconds, after a write transfer.
+ spi-buses:
+ description:
+ Array of bus numbers that describes which SPI buses of the controller are
+ connected to the peripheral. This only applies to peripherals connected
+ to specialized SPI controllers that have multiple SPI buses on a single
+ controller.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ default: [0]
+
stacked-memories:
description: Several SPI memories can be wired in stacked mode.
This basically means that either a device features several chip
--
2.43.0
---
From: David Lechner <dlechner@baylibre.com>
Date: Thu, 23 Jan 2025 15:35:19 -0600
Subject: [PATCH 2/2] spi: add support for multi-bus controllers
Add support for SPI controllers with multiple physical SPI buses.
This is common in the type of controller that can be used with parallel
flash memories, but can be used for general purpose SPI as well.
To indicate support, a controller just needs to set ctlr->num_buses to
something greater than 1. Peripherals indicate which bus they are
connected to via device tree (ACPI support can be added if needed).
In the future, this can be extended to support peripherals that also
have multiple SPI buses to use those buses at the same time by adding
a similar bus flags field to struct spi_transfer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
---
drivers/spi/spi.c | 26 +++++++++++++++++++++++++-
include/linux/spi/spi.h | 13 +++++++++++++
2 files changed, 38 insertions(+), 1 deletion(-)
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 10c365e9100a..f7722e5e906d 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -2364,7 +2364,7 @@ static void of_spi_parse_dt_cs_delay(struct device_node *nc,
static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
struct device_node *nc)
{
- u32 value, cs[SPI_CS_CNT_MAX];
+ u32 value, buses[8], cs[SPI_CS_CNT_MAX];
int rc, idx;
/* Mode (clock phase/polarity/etc.) */
@@ -2379,6 +2379,29 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
if (of_property_read_bool(nc, "spi-cs-high"))
spi->mode |= SPI_CS_HIGH;
+ rc = of_property_read_variable_u32_array(nc, "spi-buses", buses, 1,
+ ARRAY_SIZE(buses));
+ if (rc < 0 && rc != -EINVAL) {
+ dev_err(&ctlr->dev, "%pOF has invalid 'spi-buses' property (%d)\n",
+ nc, rc);
+ return rc;
+ }
+
+ if (rc == -EINVAL) {
+ /* Default when property is omitted. */
+ spi->buses = BIT(0);
+ } else {
+ for (idx = 0; idx < rc; idx++) {
+ if (buses[idx] >= ctlr->num_buses) {
+ dev_err(&ctlr->dev,
+ "%pOF has out of range 'spi-buses' property (%d)\n",
+ nc, buses[idx]);
+ return -EINVAL;
+ }
+ spi->buses |= BIT(buses[idx]);
+ }
+ }
+
/* Device DUAL/QUAD mode */
if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
switch (value) {
@@ -3072,6 +3095,7 @@ struct spi_controller *__spi_alloc_controller(struct device *dev,
mutex_init(&ctlr->add_lock);
ctlr->bus_num = -1;
ctlr->num_chipselect = 1;
+ ctlr->num_buses = 1;
ctlr->slave = slave;
if (IS_ENABLED(CONFIG_SPI_SLAVE) && slave)
ctlr->dev.class = &spi_slave_class;
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 4c087009cf97..bc45d70e8c45 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -187,6 +187,11 @@ struct spi_device {
struct device dev;
struct spi_controller *controller;
u32 max_speed_hz;
+ /*
+ * Bit flags indicating which buses this device is connected to. Only
+ * applicable to multi-bus controllers.
+ */
+ u8 buses;
u8 chip_select[SPI_CS_CNT_MAX];
u8 bits_per_word;
bool rt;
@@ -570,6 +575,14 @@ struct spi_controller {
*/
u16 num_chipselect;
+ /*
+ * Some specialized SPI controllers can have more than one physical
+ * bus interface per controller. This specifies the number of buses
+ * in that case. Other controllers do not need to set this (defaults
+ * to 1).
+ */
+ u16 num_buses;
+
/* Some SPI controllers pose alignment requirements on DMAable
* buffers; let protocol drivers know about these requirements.
*/
--
2.43.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-23 21:59 ` David Lechner
@ 2025-01-23 22:37 ` Sean Anderson
2025-01-24 13:35 ` Mark Brown
2025-06-12 23:44 ` Sean Anderson
1 sibling, 1 reply; 14+ messages in thread
From: Sean Anderson @ 2025-01-23 22:37 UTC (permalink / raw)
To: David Lechner, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 1/23/25 16:59, David Lechner wrote:
> On 1/23/25 10:24 AM, Sean Anderson wrote:
>> On 1/21/25 19:16, David Lechner wrote:
>>> On 1/16/25 5:21 PM, Sean Anderson wrote:
>
> ...
>
>>> Could we make a single device connected to both buses like this work using
>>> the proposed spi-lower and spi-upper or should we consider a different binding
>>> like the one I suggested?
>>
>> If you are willing to do the work to rewrite the SPI subsystem to handle
>> this, then I don't object to it in principle. Using a property would
>> also help with forwards compatibility. On the other hand, separate
>> busses are easier to implement since they integrate better with the SPI
>> subsystem (e.g. you can just call spi_register_controller to create all
>> the slaves).
>>
>> There have been some previous patches from Xilinx to handle this
>> use case [1], but IMO they were pretty hacky. They got this feature
>> merged into U-Boot and it broke many other boards and took a lot of
>> cleanup to fix. So I have intentionally only tackled the unsynchronized
>> use case since that requires no modification to areas outside of this
>> driver. I don't need the "parallel" use case and I am not interested in
>> doing the work required to implement it.
>>
>> --Sean
>>
>> [1] https://lore.kernel.org/linux-spi/20221017121249.19061-1-amit.kumar-mahapatra@amd.com/
>
> Fair enough, and I think it can be done without breaking things like the multi
> CS support did.
>
> Here are a couple of patches. Feel free to resubmit them with your series if
> they work for you. To make it work with your series, you should just need to
> modify the .dts to look like this:
>
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-buses = <0>; /* lower */
> + };
> +
> + flash@1 {
> + reg = <1>;
> + compatible = "jedec,spi-nor";
> + /* also OK to omit property in case of spi-buses = <0>; */
> + };
> +
> + flash@2 {
> + reg = <2>;
> + compatible = "jedec,spi-nor";
> + spi-buses = <1>; /* upper */
> + };
>
>
> Then drop patch "spi: zynqmp-gqspi: Split the bus" of course.
>
> In zynqmp_qspi_probe(), add a line:
>
> ctlr->num_buses = 2;
>
> And in the zynqmp_qspi_transfer_one() function, use spi->buses to select the
> correct bus:
>
> xqspi->genfifobus = FIELD_PREP(GQSPI_GENFIFO_BUS_MASK, spi->buses);
>
> I don't have a SPI controller on hand with multiple buses, so I don't have
> any patch adding support to a specific controller. But I did build and run this
> and hacked in some stuff to the drivers I am working on to make sure it is
> working as advertised as best as I could with a single bus.
Your patches LGTM. I will use them for v2. Mark do you have any comments on this
approach?
--Sean
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-23 22:37 ` Sean Anderson
@ 2025-01-24 13:35 ` Mark Brown
0 siblings, 0 replies; 14+ messages in thread
From: Mark Brown @ 2025-01-24 13:35 UTC (permalink / raw)
To: Sean Anderson
Cc: David Lechner, Michal Simek, linux-spi, Jinjie Ruan,
linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
[-- Attachment #1: Type: text/plain, Size: 175 bytes --]
On Thu, Jan 23, 2025 at 05:37:16PM -0500, Sean Anderson wrote:
> Your patches LGTM. I will use them for v2. Mark do you have any comments on this
> approach?
It looks fine.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-01-23 21:59 ` David Lechner
2025-01-23 22:37 ` Sean Anderson
@ 2025-06-12 23:44 ` Sean Anderson
2025-06-13 14:20 ` David Lechner
1 sibling, 1 reply; 14+ messages in thread
From: Sean Anderson @ 2025-06-12 23:44 UTC (permalink / raw)
To: David Lechner, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
Hi David,
I am (finally!) getting around to doing v2 of this series, and I ran
into a small problem with your proposed solution.
On 1/23/25 16:59, David Lechner wrote:
> ---
> From: David Lechner <dlechner@baylibre.com>
> Date: Thu, 23 Jan 2025 15:35:19 -0600
> Subject: [PATCH 2/2] spi: add support for multi-bus controllers
>
> Add support for SPI controllers with multiple physical SPI buses.
>
> This is common in the type of controller that can be used with parallel
> flash memories, but can be used for general purpose SPI as well.
>
> To indicate support, a controller just needs to set ctlr->num_buses to
> something greater than 1. Peripherals indicate which bus they are
> connected to via device tree (ACPI support can be added if needed).
>
> In the future, this can be extended to support peripherals that also
> have multiple SPI buses to use those buses at the same time by adding
> a similar bus flags field to struct spi_transfer.
>
> Signed-off-by: David Lechner <dlechner@baylibre.com>
> ---
> drivers/spi/spi.c | 26 +++++++++++++++++++++++++-
> include/linux/spi/spi.h | 13 +++++++++++++
> 2 files changed, 38 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
> index 10c365e9100a..f7722e5e906d 100644
> --- a/drivers/spi/spi.c
> +++ b/drivers/spi/spi.c
> @@ -2364,7 +2364,7 @@ static void of_spi_parse_dt_cs_delay(struct device_node *nc,
> static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
> struct device_node *nc)
> {
> - u32 value, cs[SPI_CS_CNT_MAX];
> + u32 value, buses[8], cs[SPI_CS_CNT_MAX];
> int rc, idx;
>
> /* Mode (clock phase/polarity/etc.) */
> @@ -2379,6 +2379,29 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
> if (of_property_read_bool(nc, "spi-cs-high"))
> spi->mode |= SPI_CS_HIGH;
>
> + rc = of_property_read_variable_u32_array(nc, "spi-buses", buses, 1,
> + ARRAY_SIZE(buses));
> + if (rc < 0 && rc != -EINVAL) {
> + dev_err(&ctlr->dev, "%pOF has invalid 'spi-buses' property (%d)\n",
> + nc, rc);
> + return rc;
> + }
> +
> + if (rc == -EINVAL) {
> + /* Default when property is omitted. */
> + spi->buses = BIT(0);
For backwards compatibility, the default bus for CS 1 on gqspi must be 1
and not 0. Ideally there would be some hook for the master to fix things
up when the slaves are probed, but that doesn't seem to exist. I was
thinking about doing this with OF changesets. Do you have any better
ideas?
--Sean
> + } else {
> + for (idx = 0; idx < rc; idx++) {
> + if (buses[idx] >= ctlr->num_buses) {
> + dev_err(&ctlr->dev,
> + "%pOF has out of range 'spi-buses' property (%d)\n",
> + nc, buses[idx]);
> + return -EINVAL;
> + }
> + spi->buses |= BIT(buses[idx]);
> + }
> + }
> +
> /* Device DUAL/QUAD mode */
> if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
> switch (value) {
> @@ -3072,6 +3095,7 @@ struct spi_controller *__spi_alloc_controller(struct device *dev,
> mutex_init(&ctlr->add_lock);
> ctlr->bus_num = -1;
> ctlr->num_chipselect = 1;
> + ctlr->num_buses = 1;
> ctlr->slave = slave;
> if (IS_ENABLED(CONFIG_SPI_SLAVE) && slave)
> ctlr->dev.class = &spi_slave_class;
> diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
> index 4c087009cf97..bc45d70e8c45 100644
> --- a/include/linux/spi/spi.h
> +++ b/include/linux/spi/spi.h
> @@ -187,6 +187,11 @@ struct spi_device {
> struct device dev;
> struct spi_controller *controller;
> u32 max_speed_hz;
> + /*
> + * Bit flags indicating which buses this device is connected to. Only
> + * applicable to multi-bus controllers.
> + */
> + u8 buses;
> u8 chip_select[SPI_CS_CNT_MAX];
> u8 bits_per_word;
> bool rt;
> @@ -570,6 +575,14 @@ struct spi_controller {
> */
> u16 num_chipselect;
>
> + /*
> + * Some specialized SPI controllers can have more than one physical
> + * bus interface per controller. This specifies the number of buses
> + * in that case. Other controllers do not need to set this (defaults
> + * to 1).
> + */
> + u16 num_buses;
> +
> /* Some SPI controllers pose alignment requirements on DMAable
> * buffers; let protocol drivers know about these requirements.
> */
> --
> 2.43.0
>
>
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-06-12 23:44 ` Sean Anderson
@ 2025-06-13 14:20 ` David Lechner
2025-06-13 15:57 ` Sean Anderson
0 siblings, 1 reply; 14+ messages in thread
From: David Lechner @ 2025-06-13 14:20 UTC (permalink / raw)
To: Sean Anderson, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 6/12/25 6:44 PM, Sean Anderson wrote:
> Hi David,
>
> I am (finally!) getting around to doing v2 of this series, and I ran
> into a small problem with your proposed solution.
>
> On 1/23/25 16:59, David Lechner wrote:
>> ---
>> From: David Lechner <dlechner@baylibre.com>
>> Date: Thu, 23 Jan 2025 15:35:19 -0600
>> Subject: [PATCH 2/2] spi: add support for multi-bus controllers
>>
>> Add support for SPI controllers with multiple physical SPI buses.
>>
>> This is common in the type of controller that can be used with parallel
>> flash memories, but can be used for general purpose SPI as well.
>>
>> To indicate support, a controller just needs to set ctlr->num_buses to
>> something greater than 1. Peripherals indicate which bus they are
>> connected to via device tree (ACPI support can be added if needed).
>>
>> In the future, this can be extended to support peripherals that also
>> have multiple SPI buses to use those buses at the same time by adding
>> a similar bus flags field to struct spi_transfer.
>>
>> Signed-off-by: David Lechner <dlechner@baylibre.com>
>> ---
>> drivers/spi/spi.c | 26 +++++++++++++++++++++++++-
>> include/linux/spi/spi.h | 13 +++++++++++++
>> 2 files changed, 38 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
>> index 10c365e9100a..f7722e5e906d 100644
>> --- a/drivers/spi/spi.c
>> +++ b/drivers/spi/spi.c
>> @@ -2364,7 +2364,7 @@ static void of_spi_parse_dt_cs_delay(struct device_node *nc,
>> static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>> struct device_node *nc)
>> {
>> - u32 value, cs[SPI_CS_CNT_MAX];
>> + u32 value, buses[8], cs[SPI_CS_CNT_MAX];
>> int rc, idx;
>>
>> /* Mode (clock phase/polarity/etc.) */
>> @@ -2379,6 +2379,29 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>> if (of_property_read_bool(nc, "spi-cs-high"))
>> spi->mode |= SPI_CS_HIGH;
>>
>> + rc = of_property_read_variable_u32_array(nc, "spi-buses", buses, 1,
>> + ARRAY_SIZE(buses));
>> + if (rc < 0 && rc != -EINVAL) {
>> + dev_err(&ctlr->dev, "%pOF has invalid 'spi-buses' property (%d)\n",
>> + nc, rc);
>> + return rc;
>> + }
>> +
>> + if (rc == -EINVAL) {
>> + /* Default when property is omitted. */
>> + spi->buses = BIT(0);
>
> For backwards compatibility, the default bus for CS 1 on gqspi must be 1
> and not 0. Ideally there would be some hook for the master to fix things
> up when the slaves are probed, but that doesn't seem to exist. I was
> thinking about doing this with OF changesets. Do you have any better
> ideas?
>
Does this work?
spi->buses = BIT(cs[0]);
(would have to move all the new code after cs[0] is assigned of course)
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-06-13 14:20 ` David Lechner
@ 2025-06-13 15:57 ` Sean Anderson
2025-06-13 16:44 ` Sean Anderson
2025-06-13 16:53 ` David Lechner
0 siblings, 2 replies; 14+ messages in thread
From: Sean Anderson @ 2025-06-13 15:57 UTC (permalink / raw)
To: David Lechner, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 6/13/25 10:20, David Lechner wrote:
> On 6/12/25 6:44 PM, Sean Anderson wrote:
>> Hi David,
>>
>> I am (finally!) getting around to doing v2 of this series, and I ran
>> into a small problem with your proposed solution.
>>
>> On 1/23/25 16:59, David Lechner wrote:
>>> ---
>>> From: David Lechner <dlechner@baylibre.com>
>>> Date: Thu, 23 Jan 2025 15:35:19 -0600
>>> Subject: [PATCH 2/2] spi: add support for multi-bus controllers
>>>
>>> Add support for SPI controllers with multiple physical SPI buses.
>>>
>>> This is common in the type of controller that can be used with parallel
>>> flash memories, but can be used for general purpose SPI as well.
>>>
>>> To indicate support, a controller just needs to set ctlr->num_buses to
>>> something greater than 1. Peripherals indicate which bus they are
>>> connected to via device tree (ACPI support can be added if needed).
>>>
>>> In the future, this can be extended to support peripherals that also
>>> have multiple SPI buses to use those buses at the same time by adding
>>> a similar bus flags field to struct spi_transfer.
>>>
>>> Signed-off-by: David Lechner <dlechner@baylibre.com>
>>> ---
>>> drivers/spi/spi.c | 26 +++++++++++++++++++++++++-
>>> include/linux/spi/spi.h | 13 +++++++++++++
>>> 2 files changed, 38 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
>>> index 10c365e9100a..f7722e5e906d 100644
>>> --- a/drivers/spi/spi.c
>>> +++ b/drivers/spi/spi.c
>>> @@ -2364,7 +2364,7 @@ static void of_spi_parse_dt_cs_delay(struct device_node *nc,
>>> static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>>> struct device_node *nc)
>>> {
>>> - u32 value, cs[SPI_CS_CNT_MAX];
>>> + u32 value, buses[8], cs[SPI_CS_CNT_MAX];
>>> int rc, idx;
>>>
>>> /* Mode (clock phase/polarity/etc.) */
>>> @@ -2379,6 +2379,29 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>>> if (of_property_read_bool(nc, "spi-cs-high"))
>>> spi->mode |= SPI_CS_HIGH;
>>>
>>> + rc = of_property_read_variable_u32_array(nc, "spi-buses", buses, 1,
>>> + ARRAY_SIZE(buses));
>>> + if (rc < 0 && rc != -EINVAL) {
>>> + dev_err(&ctlr->dev, "%pOF has invalid 'spi-buses' property (%d)\n",
>>> + nc, rc);
>>> + return rc;
>>> + }
>>> +
>>> + if (rc == -EINVAL) {
>>> + /* Default when property is omitted. */
>>> + spi->buses = BIT(0);
>>
>> For backwards compatibility, the default bus for CS 1 on gqspi must be 1
>> and not 0. Ideally there would be some hook for the master to fix things
>> up when the slaves are probed, but that doesn't seem to exist. I was
>> thinking about doing this with OF changesets. Do you have any better
>> ideas?
>>
>
> Does this work?
>
> spi->buses = BIT(cs[0]);
>
> (would have to move all the new code after cs[0] is assigned of course)
Yeah, but do we really want to make this the default for all drivers?
This is really a quirk of the existing gqspi binding and I don't think
it makes sense in general.
--Sean
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-06-13 15:57 ` Sean Anderson
@ 2025-06-13 16:44 ` Sean Anderson
2025-06-13 16:53 ` David Lechner
1 sibling, 0 replies; 14+ messages in thread
From: Sean Anderson @ 2025-06-13 16:44 UTC (permalink / raw)
To: David Lechner, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 6/13/25 11:57, Sean Anderson wrote:
> On 6/13/25 10:20, David Lechner wrote:
>> On 6/12/25 6:44 PM, Sean Anderson wrote:
>>> Hi David,
>>>
>>> I am (finally!) getting around to doing v2 of this series, and I ran
>>> into a small problem with your proposed solution.
>>>
>>> On 1/23/25 16:59, David Lechner wrote:
>>>> ---
>>>> From: David Lechner <dlechner@baylibre.com>
>>>> Date: Thu, 23 Jan 2025 15:35:19 -0600
>>>> Subject: [PATCH 2/2] spi: add support for multi-bus controllers
>>>>
>>>> Add support for SPI controllers with multiple physical SPI buses.
>>>>
>>>> This is common in the type of controller that can be used with parallel
>>>> flash memories, but can be used for general purpose SPI as well.
>>>>
>>>> To indicate support, a controller just needs to set ctlr->num_buses to
>>>> something greater than 1. Peripherals indicate which bus they are
>>>> connected to via device tree (ACPI support can be added if needed).
>>>>
>>>> In the future, this can be extended to support peripherals that also
>>>> have multiple SPI buses to use those buses at the same time by adding
>>>> a similar bus flags field to struct spi_transfer.
>>>>
>>>> Signed-off-by: David Lechner <dlechner@baylibre.com>
>>>> ---
>>>> drivers/spi/spi.c | 26 +++++++++++++++++++++++++-
>>>> include/linux/spi/spi.h | 13 +++++++++++++
>>>> 2 files changed, 38 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
>>>> index 10c365e9100a..f7722e5e906d 100644
>>>> --- a/drivers/spi/spi.c
>>>> +++ b/drivers/spi/spi.c
>>>> @@ -2364,7 +2364,7 @@ static void of_spi_parse_dt_cs_delay(struct device_node *nc,
>>>> static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>>>> struct device_node *nc)
>>>> {
>>>> - u32 value, cs[SPI_CS_CNT_MAX];
>>>> + u32 value, buses[8], cs[SPI_CS_CNT_MAX];
>>>> int rc, idx;
>>>>
>>>> /* Mode (clock phase/polarity/etc.) */
>>>> @@ -2379,6 +2379,29 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>>>> if (of_property_read_bool(nc, "spi-cs-high"))
>>>> spi->mode |= SPI_CS_HIGH;
>>>>
>>>> + rc = of_property_read_variable_u32_array(nc, "spi-buses", buses, 1,
>>>> + ARRAY_SIZE(buses));
>>>> + if (rc < 0 && rc != -EINVAL) {
>>>> + dev_err(&ctlr->dev, "%pOF has invalid 'spi-buses' property (%d)\n",
>>>> + nc, rc);
>>>> + return rc;
>>>> + }
>>>> +
>>>> + if (rc == -EINVAL) {
>>>> + /* Default when property is omitted. */
>>>> + spi->buses = BIT(0);
>>>
>>> For backwards compatibility, the default bus for CS 1 on gqspi must be 1
>>> and not 0. Ideally there would be some hook for the master to fix things
>>> up when the slaves are probed, but that doesn't seem to exist. I was
>>> thinking about doing this with OF changesets. Do you have any better
>>> ideas?
>>>
>>
>> Does this work?
>>
>> spi->buses = BIT(cs[0]);
>>
>> (would have to move all the new code after cs[0] is assigned of course)
>
> Yeah, but do we really want to make this the default for all drivers?
> This is really a quirk of the existing gqspi binding and I don't think
> it makes sense in general.
I think I will add a flag like
/* Default when property is omitted. */
if (ctlr->flags & SPI_CONTROLLER_DEFAULT_BUS_IS_CS)
spi->buses = BIT(cs[0]);
else
spi->buses = BIT(0);
which should keep the defaults sane for everyone else.
--Sean
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus
2025-06-13 15:57 ` Sean Anderson
2025-06-13 16:44 ` Sean Anderson
@ 2025-06-13 16:53 ` David Lechner
1 sibling, 0 replies; 14+ messages in thread
From: David Lechner @ 2025-06-13 16:53 UTC (permalink / raw)
To: Sean Anderson, Mark Brown, Michal Simek, linux-spi
Cc: Jinjie Ruan, linux-arm-kernel, Amit Kumar Mahapatra, linux-kernel,
Miquel Raynal, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
devicetree, linux-iio@vger.kernel.org, Jonathan Cameron,
Nuno Sá
On 6/13/25 10:57 AM, Sean Anderson wrote:
> On 6/13/25 10:20, David Lechner wrote:
>> On 6/12/25 6:44 PM, Sean Anderson wrote:
>>> Hi David,
>>>
>>> I am (finally!) getting around to doing v2 of this series, and I ran
>>> into a small problem with your proposed solution.
>>>
>>> On 1/23/25 16:59, David Lechner wrote:
>>>> ---
>>>> From: David Lechner <dlechner@baylibre.com>
>>>> Date: Thu, 23 Jan 2025 15:35:19 -0600
>>>> Subject: [PATCH 2/2] spi: add support for multi-bus controllers
>>>>
>>>> Add support for SPI controllers with multiple physical SPI buses.
>>>>
>>>> This is common in the type of controller that can be used with parallel
>>>> flash memories, but can be used for general purpose SPI as well.
>>>>
>>>> To indicate support, a controller just needs to set ctlr->num_buses to
>>>> something greater than 1. Peripherals indicate which bus they are
>>>> connected to via device tree (ACPI support can be added if needed).
>>>>
>>>> In the future, this can be extended to support peripherals that also
>>>> have multiple SPI buses to use those buses at the same time by adding
>>>> a similar bus flags field to struct spi_transfer.
>>>>
>>>> Signed-off-by: David Lechner <dlechner@baylibre.com>
>>>> ---
>>>> drivers/spi/spi.c | 26 +++++++++++++++++++++++++-
>>>> include/linux/spi/spi.h | 13 +++++++++++++
>>>> 2 files changed, 38 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
>>>> index 10c365e9100a..f7722e5e906d 100644
>>>> --- a/drivers/spi/spi.c
>>>> +++ b/drivers/spi/spi.c
>>>> @@ -2364,7 +2364,7 @@ static void of_spi_parse_dt_cs_delay(struct device_node *nc,
>>>> static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>>>> struct device_node *nc)
>>>> {
>>>> - u32 value, cs[SPI_CS_CNT_MAX];
>>>> + u32 value, buses[8], cs[SPI_CS_CNT_MAX];
>>>> int rc, idx;
>>>>
>>>> /* Mode (clock phase/polarity/etc.) */
>>>> @@ -2379,6 +2379,29 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
>>>> if (of_property_read_bool(nc, "spi-cs-high"))
>>>> spi->mode |= SPI_CS_HIGH;
>>>>
>>>> + rc = of_property_read_variable_u32_array(nc, "spi-buses", buses, 1,
>>>> + ARRAY_SIZE(buses));
>>>> + if (rc < 0 && rc != -EINVAL) {
>>>> + dev_err(&ctlr->dev, "%pOF has invalid 'spi-buses' property (%d)\n",
>>>> + nc, rc);
>>>> + return rc;
>>>> + }
>>>> +
>>>> + if (rc == -EINVAL) {
>>>> + /* Default when property is omitted. */
>>>> + spi->buses = BIT(0);
>>>
>>> For backwards compatibility, the default bus for CS 1 on gqspi must be 1
>>> and not 0. Ideally there would be some hook for the master to fix things
>>> up when the slaves are probed, but that doesn't seem to exist. I was
>>> thinking about doing this with OF changesets. Do you have any better
>>> ideas?
>>>
>>
>> Does this work?
>>
>> spi->buses = BIT(cs[0]);
>>
>> (would have to move all the new code after cs[0] is assigned of course)
>
> Yeah, but do we really want to make this the default for all drivers?
> This is really a quirk of the existing gqspi binding and I don't think
> it makes sense in general.
>
Can we just leave spi->buses unset then and leave it up to the controller
driver to interpret that as "default" and handle it appropriately?
OF changessets seems overkill to me.
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2025-06-13 16:53 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-01-16 23:21 [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
2025-01-16 23:21 ` [PATCH 1/7] dt-bindings: spi: zynqmp-qspi: Split the bus Sean Anderson
2025-01-22 0:16 ` David Lechner
2025-01-23 16:24 ` Sean Anderson
2025-01-23 21:59 ` David Lechner
2025-01-23 22:37 ` Sean Anderson
2025-01-24 13:35 ` Mark Brown
2025-06-12 23:44 ` Sean Anderson
2025-06-13 14:20 ` David Lechner
2025-06-13 15:57 ` Sean Anderson
2025-06-13 16:44 ` Sean Anderson
2025-06-13 16:53 ` David Lechner
2025-01-16 23:21 ` [PATCH 7/7] ARM64: xilinx: zynqmp: Convert to split QSPI bus Sean Anderson
2025-01-16 23:24 ` [PATCH 0/7] spi: zynqmp-gqspi: Split the bus and add GPIO support Sean Anderson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).