[PATCH v4 00/11] Add BananaPi R3

[PATCH v4 00/11] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on Matthias' DTS64 next Branch from 2022/11/11.

i included sams series for mt7986 DTS with small changes
https://patchwork.kernel.org/project/linux-mediatek/cover/20220427124741.18245-1-sam.shih@mediatek.com/

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137

changes:
v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches
v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays


Frank Wunderlich (7):
  arm64: dts: mt7986: move wed_pcie node
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  dt-bindings: usb: mtk-xhci: add support for mt7986
  dt-bindings: PCI: mediatek-gen3: add SoC based clock config
  dt-bindings: PCI: mediatek-gen3: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3
  arm64: dts: mt7986: add BPI-R3 nand/nor overlays

Sam Shih (4):
  arm64: dts: mt7986: add spi related device nodes
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/pci/mediatek-pcie-gen3.yaml      |  64 ++-
 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 .../bindings/usb/mediatek,mtk-xhci.yaml       |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   4 +
 .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts |  31 ++
 .../mediatek/mt7986a-bananapi-bpi-r3-nand.dts |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dts  |  69 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts   |  25 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 458 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 166 +++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 162 ++++++-
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |  63 +++
 12 files changed, 1081 insertions(+), 18 deletions(-)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi

-- 
2.34.1

[PATCH v4 01/11] arm64: dts: mt7986: move wed_pcie node

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Move the wed_pcie node to have node aligned by address.

Fixes: 00b9903996b3 ("arm64: dts: mediatek: mt7986: add support for Wireless Ethernet Dispatch")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index a22e10e89ab9..afc01abfa99c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -112,6 +112,12 @@ infracfg: infracfg@10001000 {
 			#clock-cells = <1>;
 		};
 
+		wed_pcie: wed-pcie@10003000 {
+			compatible = "mediatek,mt7986-wed-pcie",
+				     "syscon";
+			reg = <0 0x10003000 0 0x10>;
+		};
+
 		topckgen: topckgen@1001b000 {
 			compatible = "mediatek,mt7986-topckgen", "syscon";
 			reg = <0 0x1001B000 0 0x1000>;
@@ -257,12 +263,6 @@ ethsys: syscon@15000000 {
 			 #reset-cells = <1>;
 		};
 
-		wed_pcie: wed-pcie@10003000 {
-			compatible = "mediatek,mt7986-wed-pcie",
-				     "syscon";
-			reg = <0 0x10003000 0 0x10>;
-		};
-
 		wed0: wed@15010000 {
 			compatible = "mediatek,mt7986-wed",
 				     "syscon";
-- 
2.34.1

Re: [PATCH v4 01/11] arm64: dts: mt7986: move wed_pcie node

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Move the wed_pcie node to have node aligned by address.
> 
> Fixes: 00b9903996b3 ("arm64: dts: mediatek: mt7986: add support for Wireless Ethernet Dispatch")
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 02/11] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
 Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
           - enum:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
+              - mediatek,mt7986-tphy
               - mediatek,mt8183-tphy
               - mediatek,mt8186-tphy
               - mediatek,mt8192-tphy
-- 
2.34.1

Aw: [PATCH v4 02/11] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

i've noticed that i missed the Ack from Krzysztof i've got in v1 [1]

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

[1] https://patchwork.kernel.org/project/linux-mediatek/patch/20221017104141.7338-2-linux@fw-web.de/

regards Frank

Re: [PATCH v4 02/11] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Chunfeng Yun (云春峰)]

On Sat, 2022-11-12 at 10:15 +0100, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add compatible string for mt7986.
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
>  Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> index 5613cc5106e3..230a17f24966 100644
> --- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> +++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> @@ -79,6 +79,7 @@ properties:
>            - enum:
>                - mediatek,mt2712-tphy
>                - mediatek,mt7629-tphy
> +              - mediatek,mt7986-tphy
>                - mediatek,mt8183-tphy
>                - mediatek,mt8186-tphy
>                - mediatek,mt8192-tphy

Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>

Thanks

Re: [PATCH v4 02/11] dt-bindings: phy: mediatek,tphy: add support for mt7986

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add compatible string for mt7986.
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 03/11] dt-bindings: usb: mtk-xhci: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index 939623867a64..a3c37944c630 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -28,6 +28,7 @@ properties:
           - mediatek,mt7622-xhci
           - mediatek,mt7623-xhci
           - mediatek,mt7629-xhci
+          - mediatek,mt7986-xhci
           - mediatek,mt8173-xhci
           - mediatek,mt8183-xhci
           - mediatek,mt8186-xhci
-- 
2.34.1

Aw: [PATCH v4 03/11] dt-bindings: usb: mtk-xhci: add support for mt7986

[Frank Wunderlich]

i've noticed that i missed the Ack from Krzysztof i've got in v1 [1]

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

[1] https://patchwork.kernel.org/project/linux-mediatek/patch/20221017104141.7338-4-linux@fw-web.de/

regards Frank

Re: [PATCH v4 03/11] dt-bindings: usb: mtk-xhci: add support for mt7986

[Chunfeng Yun (云春峰)]

On Sat, 2022-11-12 at 10:15 +0100, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add compatible string for mt7986.
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
>  Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-
> xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-
> xhci.yaml
> index 939623867a64..a3c37944c630 100644
> --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> @@ -28,6 +28,7 @@ properties:
>            - mediatek,mt7622-xhci
>            - mediatek,mt7623-xhci
>            - mediatek,mt7629-xhci
> +          - mediatek,mt7986-xhci
>            - mediatek,mt8173-xhci
>            - mediatek,mt8183-xhci
>            - mediatek,mt8186-xhci

Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>

Thanks

Re: [PATCH v4 03/11] dt-bindings: usb: mtk-xhci: add support for mt7986

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add compatible string for mt7986.
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 04/11] dt-bindings: PCI: mediatek-gen3: add SoC based clock config

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

The PCIe driver covers different SOC which needing different clock
configs. Define them based on compatible.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
---
v2:
- fix typo in mediatek,mt8192-pcie
v3:
- remove contains to match only if compatible is no fallback
  tested with series "Add driver nodes for MT8195 SoC" and mt7986
  pcie-nodes, dtbs_check is now clean
---
 .../bindings/pci/mediatek-pcie-gen3.yaml      | 47 ++++++++++++++-----
 1 file changed, 35 insertions(+), 12 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
index c00be39af64e..5d7369debff2 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
@@ -43,9 +43,6 @@ description: |+
   each set has its own address for MSI message, and supports 32 MSI vectors
   to generate interrupt.
 
-allOf:
-  - $ref: /schemas/pci/pci-bus.yaml#
-
 properties:
   compatible:
     oneOf:
@@ -84,15 +81,7 @@ properties:
     maxItems: 6
 
   clock-names:
-    items:
-      - const: pl_250m
-      - const: tl_26m
-      - const: tl_96m
-      - const: tl_32k
-      - const: peri_26m
-      - enum:
-          - top_133m        # for MT8192
-          - peri_mem        # for MT8188/MT8195
+    maxItems: 6
 
   assigned-clocks:
     maxItems: 1
@@ -138,6 +127,40 @@ required:
   - '#interrupt-cells'
   - interrupt-controller
 
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+  - if:
+      properties:
+        compatible:
+          const: mediatek,mt8192-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: pl_250m
+            - const: tl_26m
+            - const: tl_96m
+            - const: tl_32k
+            - const: peri_26m
+            - const: top_133m
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt8188-pcie
+              - mediatek,mt8195-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: pl_250m
+            - const: tl_26m
+            - const: tl_96m
+            - const: tl_32k
+            - const: peri_26m
+            - const: peri_mem
+
 unevaluatedProperties: false
 
 examples:
-- 
2.34.1

Re: [PATCH v4 04/11] dt-bindings: PCI: mediatek-gen3: add SoC based clock config

[Frank Wunderlich]

I missed ack i've got here:

https://patchwork.kernel.org/project/linux-mediatek/patch/20221029175806.14899-2-frank-w@public-files.de/

Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
regards Frank

Re: [PATCH v4 04/11] dt-bindings: PCI: mediatek-gen3: add SoC based clock config

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> The PCIe driver covers different SOC which needing different clock
> configs. Define them based on compatible.
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 05/11] dt-bindings: PCI: mediatek-gen3: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string and clock-definition for mt7986. It needs 4 clocks
for PCIe, define them in binding.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
---
v2:
- squashed patch 2+3 (compatible and clock definition)
---
 .../bindings/pci/mediatek-pcie-gen3.yaml        | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
index 5d7369debff2..f7a02019daea 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
@@ -48,6 +48,7 @@ properties:
     oneOf:
       - items:
           - enum:
+              - mediatek,mt7986-pcie
               - mediatek,mt8188-pcie
               - mediatek,mt8195-pcie
           - const: mediatek,mt8192-pcie
@@ -78,9 +79,11 @@ properties:
       - const: mac
 
   clocks:
+    minItems: 4
     maxItems: 6
 
   clock-names:
+    minItems: 4
     maxItems: 6
 
   assigned-clocks:
@@ -160,6 +163,20 @@ allOf:
             - const: tl_32k
             - const: peri_26m
             - const: peri_mem
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt7986-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: pl_250m
+            - const: tl_26m
+            - const: peri_26m
+            - const: top_133m
 
 unevaluatedProperties: false
 
-- 
2.34.1

Re: [PATCH v4 05/11] dt-bindings: PCI: mediatek-gen3: add support for mt7986

[Frank Wunderlich]

Am 12. November 2022 10:15:12 MEZ schrieb Frank Wunderlich <linux@fw-web.de>:
>From: Frank Wunderlich <frank-w@public-files.de>
>
>Add compatible string and clock-definition for mt7986. It needs 4 clocks
>for PCIe, define them in binding.
>
>Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
>Reviewed-by: Rob Herring <robh@kernel.org>
>---
>v2:
>- squashed patch 2+3 (compatible and clock definition)
>---
> .../bindings/pci/mediatek-pcie-gen3.yaml        | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
>
>diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
>index 5d7369debff2..f7a02019daea 100644
>--- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
>+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
>@@ -48,6 +48,7 @@ properties:
>     oneOf:
>       - items:
>           - enum:
>+              - mediatek,mt7986-pcie
>               - mediatek,mt8188-pcie
>               - mediatek,mt8195-pcie
>           - const: mediatek,mt8192-pcie
>@@ -78,9 +79,11 @@ properties:
>       - const: mac
> 
>   clocks:
>+    minItems: 4
>     maxItems: 6
> 
>   clock-names:
>+    minItems: 4
>     maxItems: 6
> 
>   assigned-clocks:
>@@ -160,6 +163,20 @@ allOf:
>             - const: tl_32k
>             - const: peri_26m
>             - const: peri_mem
>+  - if:
>+      properties:
>+        compatible:
>+          contains:
>+            enum:
>+              - mediatek,mt7986-pcie
>+    then:
>+      properties:
>+        clock-names:
>+          items:
>+            - const: pl_250m
>+            - const: tl_26m
>+            - const: peri_26m
>+            - const: top_133m
> 
> unevaluatedProperties: false
> 

Missed ack i got here:

https://patchwork.kernel.org/project/linux-mediatek/patch/20221029175806.14899-3-frank-w@public-files.de/

Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
regards Frank

[PATCH v4 06/11] arm64: dts: mt7986: add spi related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds spi support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 35 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 28 ++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 35 ++++++++++++++++++++
 3 files changed, 98 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 2f48cc3d3ddb..006878e3f2b2 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -59,6 +59,20 @@ switch: switch@0 {
 };
 
 &pio {
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_2";
+		};
+	};
+
 	uart1_pins: uart1-pins {
 		mux {
 			function = "uart";
@@ -105,6 +119,27 @@ conf {
 	};
 };
 
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+	spi_nand: spi_nand@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		spi-tx-buswidth = <4>;
+		spi-rx-buswidth = <4>;
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index afc01abfa99c..29da9b8ed753 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -253,6 +253,34 @@ i2c0: i2c@11008000 {
 			status = "disabled";
 		};
 
+		spi0: spi@1100a000 {
+			compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x1100a000 0 0x100>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_MPLL_D2>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI0_CK>,
+				 <&infracfg CLK_INFRA_SPI0_HCK_CK>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
+			status = "disabled";
+		};
+
+		spi1: spi@1100b000 {
+			compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x1100b000 0 0x100>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_MPLL_D2>,
+				 <&topckgen CLK_TOP_SPIM_MST_SEL>,
+				 <&infracfg CLK_INFRA_SPI1_CK>,
+				 <&infracfg CLK_INFRA_SPI1_HCK_CK>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
+			status = "disabled";
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 79c5c78f7a14..2c7f1d4fb352 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -100,6 +100,20 @@ fixed-link {
 };
 
 &pio {
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_2";
+		};
+	};
+
 	wf_2g_5g_pins: wf-2g-5g-pins {
 		mux {
 			function = "wifi";
@@ -132,6 +146,27 @@ conf {
 	};
 };
 
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+	spi_nand: spi_nand@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		spi-tx-buswidth = <4>;
+		spi-rx-buswidth = <4>;
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
-- 
2.34.1

Re: [PATCH v4 06/11] arm64: dts: mt7986: add spi related device nodes

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Sam Shih <sam.shih@mediatek.com>
> 
> This patch adds spi support for MT7986.
> 
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 07/11] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds USB support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
changes compared to sams original version:
- reorder xhci-clocks based on yaml binding
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 28 ++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 28 ++++++++++
 3 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 006878e3f2b2..2b5d7ea31b4d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -23,6 +23,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -140,6 +158,12 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +225,10 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 29da9b8ed753..2bcf48890ba8 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -281,6 +281,61 @@ spi1: spi@1100b000 {
 			status = "disabled";
 		};
 
+		ssusb: usb@11200000 {
+			compatible = "mediatek,mt7986-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x2e00>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+				 <&infracfg CLK_INFRA_IUSB_CK>,
+				 <&infracfg CLK_INFRA_IUSB_133_CK>,
+				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
+				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+			clock-names = "sys_ck",
+				      "ref_ck",
+				      "mcu_ck",
+				      "dma_ck",
+				      "xhci_ck";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		usb_phy: t-phy@11e10000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			u2port0: usb-phy@11e10000 {
+				reg = <0 0x11e10000 0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@11e10700 {
+				reg = <0 0x11e10700 0 0x900>;
+				clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@11e11000 {
+				reg = <0 0x11e11000 0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 2c7f1d4fb352..a98025112b5a 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -23,6 +23,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -167,10 +185,20 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
-- 
2.34.1

Re: [PATCH v4 07/11] arm64: dts: mt7986: add usb related device nodes

[Chunfeng Yun (云春峰)]

On Sat, 2022-11-12 at 10:15 +0100, Frank Wunderlich wrote:
> From: Sam Shih <sam.shih@mediatek.com>
> 
> This patch adds USB support for MT7986.
> 
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
> changes compared to sams original version:
> - reorder xhci-clocks based on yaml binding
> ---
>  arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 28 ++++++++++
>  arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55
> ++++++++++++++++++++
>  arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 28 ++++++++++
>  3 files changed, 111 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> index 006878e3f2b2..2b5d7ea31b4d 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> @@ -23,6 +23,24 @@ memory@40000000 {
>  		device_type = "memory";
>  		reg = <0 0x40000000 0 0x40000000>;
>  	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-3.3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	reg_5v: regulator-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };
>  
>  &crypto {
> @@ -140,6 +158,12 @@ &spi1 {
>  	status = "okay";
>  };
>  
> +&ssusb {
> +	vusb33-supply = <&reg_3p3v>;
> +	vbus-supply = <&reg_5v>;
> +	status = "okay";
> +};
> +
>  &switch {
>  	ports {
>  		#address-cells = <1>;
> @@ -201,6 +225,10 @@ &uart2 {
>  	status = "okay";
>  };
>  
> +&usb_phy {
> +	status = "okay";
> +};
> +
>  &wifi {
>  	status = "okay";
>  	pinctrl-names = "default", "dbdc";
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> index 29da9b8ed753..2bcf48890ba8 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> @@ -281,6 +281,61 @@ spi1: spi@1100b000 {
>  			status = "disabled";
>  		};
>  
> +		ssusb: usb@11200000 {
> +			compatible = "mediatek,mt7986-xhci",
> +				     "mediatek,mtk-xhci";
> +			reg = <0 0x11200000 0 0x2e00>,
> +			      <0 0x11203e00 0 0x0100>;
> +			reg-names = "mac", "ippc";
> +			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
> +				 <&infracfg CLK_INFRA_IUSB_CK>,
> +				 <&infracfg CLK_INFRA_IUSB_133_CK>,
> +				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
> +				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
> +			clock-names = "sys_ck",
> +				      "ref_ck",
> +				      "mcu_ck",
> +				      "dma_ck",
> +				      "xhci_ck";
> +			phys = <&u2port0 PHY_TYPE_USB2>,
> +			       <&u3port0 PHY_TYPE_USB3>,
> +			       <&u2port1 PHY_TYPE_USB2>;
> +			status = "disabled";
> +		};
> +
> +		usb_phy: t-phy@11e10000 {
> +			compatible = "mediatek,mt7986-tphy",
> +				     "mediatek,generic-tphy-v2";
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
Please use ranges with a triplet value (child, parent, len), refers to:


https://elixir.bootlin.com/linux/latest/source/arch/arm64/boot/dts/mediatek/mt2712e.dtsi#L891

Thanks a lot

> +			status = "disabled";
> +
> +			u2port0: usb-phy@11e10000 {
> +				reg = <0 0x11e10000 0 0x700>;
> +				clocks = <&topckgen
> CLK_TOP_DA_U2_REFSEL>,
> +					 <&topckgen
> CLK_TOP_DA_U2_CK_1P_SEL>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +
> +			u3port0: usb-phy@11e10700 {
> +				reg = <0 0x11e10700 0 0x900>;
> +				clocks = <&topckgen
> CLK_TOP_USB3_PHY_SEL>;
> +				clock-names = "ref";
> +				#phy-cells = <1>;
> +			};
> +
> +			u2port1: usb-phy@11e11000 {
> +				reg = <0 0x11e11000 0 0x700>;
> +				clocks = <&topckgen
> CLK_TOP_DA_U2_REFSEL>,
> +					 <&topckgen
> CLK_TOP_DA_U2_CK_1P_SEL>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +		};
> +
>  		ethsys: syscon@15000000 {
>  			 #address-cells = <1>;
>  			 #size-cells = <1>;
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> index 2c7f1d4fb352..a98025112b5a 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> @@ -23,6 +23,24 @@ memory@40000000 {
>  		device_type = "memory";
>  		reg = <0 0x40000000 0 0x40000000>;
>  	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-3.3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	reg_5v: regulator-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };
>  
>  &crypto {
> @@ -167,10 +185,20 @@ &spi1 {
>  	status = "okay";
>  };
>  
> +&ssusb {
> +	vusb33-supply = <&reg_3p3v>;
> +	vbus-supply = <&reg_5v>;
> +	status = "okay";
> +};
> +
>  &uart0 {
>  	status = "okay";
>  };
>  
> +&usb_phy {
> +	status = "okay";
> +};
> +
>  &wifi {
>  	status = "okay";
>  	pinctrl-names = "default", "dbdc";

Re: [PATCH v4 07/11] arm64: dts: mt7986: add usb related device nodes

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Sam Shih <sam.shih@mediatek.com>
> 
> This patch adds USB support for MT7986.
> 
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 08/11] arm64: dts: mt7986: add mmc related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v2:
- update mmc-node because clocks changed
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 87 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 ++++
 2 files changed, 102 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 2b5d7ea31b4d..e1a0331aaa5f 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -24,6 +26,15 @@ memory@40000000 {
 		reg = <0 0x40000000 0 0x40000000>;
 	};
 
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
@@ -76,7 +87,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 2bcf48890ba8..4b85a645fd55 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -304,6 +304,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

Re: [PATCH v4 08/11] arm64: dts: mt7986: add mmc related device nodes

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Sam Shih <sam.shih@mediatek.com>
> 
> This patch adds mmc support for MT7986.
> 
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 09/11] arm64: dts: mt7986: add pcie related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds PCIe support for MT7986.

Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

---
changes compared to sams original version:

- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 52 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index e1a0331aaa5f..01fa08c57c39 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -102,6 +102,15 @@ &mmc0 {
 	non-removable;
 	no-sd;
 	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
 	status = "okay";
 };
 
@@ -164,6 +173,13 @@ conf-rst {
 		};
 	};
 
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 4b85a645fd55..97cef0fd9d8f 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/mt7986-clk.h>
 #include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -319,6 +320,57 @@ mmc0: mmc@11230000 {
 			status = "disabled";
 		};
 
+		pcie: pcie@11280000 {
+			compatible = "mediatek,mt7986-pcie",
+				     "mediatek,mt8192-pcie";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg = <0x00 0x11280000 0x00 0x4000>;
+			reg-names = "pcie-mac";
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0x00 0x20000000 0x00
+				  0x20000000 0x00 0x10000000>;
+			clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+				 <&infracfg CLK_INFRA_IPCIE_CK>,
+				 <&infracfg CLK_INFRA_IPCIER_CK>,
+				 <&infracfg CLK_INFRA_IPCIEB_CK>;
+			clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+			status = "disabled";
+
+			phys = <&pcie_port PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &pcie_intc 0>,
+					<0 0 0 2 &pcie_intc 1>,
+					<0 0 0 3 &pcie_intc 2>,
+					<0 0 0 4 &pcie_intc 3>;
+			pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie_phy: t-phy@11c00000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			pcie_port: pcie-phy@11c00000 {
+				reg = <0 0x11c00000 0 0x20000>;
+				clocks = <&clk40m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

Re: [PATCH v4 09/11] arm64: dts: mt7986: add pcie related device nodes

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Sam Shih <sam.shih@mediatek.com>
> 
> This patch adds PCIe support for MT7986.
> 
> Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v4 10/11] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
SPI-NAND/NOR switched (CS by sw5/C) not yet included
  this is done with DT-Overlays in my tree, don't know how to do it
  in upstream the right way...added dts files for dtbo and added them
  with dtbo extension to Makefile works.

changes:
v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
  thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
  - add key suffix like it's done in mt7622-bpi-r64 devicetree
  - add dash in sfp node names
  - use reg as unit for switch-node
  - drop "-3-4" suffix from i2c-pins node name
  - fix order in Makefile
---
 arch/arm64/boot/dts/mediatek/Makefile         |   2 +
 .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts |  31 ++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts   |  25 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 458 ++++++++++++++++++
 4 files changed, 516 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 0ec90cb3ef28..e8902f2cc58f 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
new file mode 100644
index 000000000000..a0ca35b5977e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986a-bananapi-bpi-r3.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3 (emmc)";
+};
+
+&mmc0 {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
new file mode 100644
index 000000000000..06e4691cb815
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986a-bananapi-bpi-r3.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3 (sdmmc)";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	max-frequency = <52000000>;
+	cap-sd-highspeed;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
new file mode 100644
index 000000000000..def16e36f1e6
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
@@ -0,0 +1,458 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@mediatek.com>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ *          Daniel Golle <daniel@makrotopia.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3";
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dcin: regulator-12vd {
+		compatible = "regulator-fixed";
+		regulator-name = "12vd";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset-key {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps-key {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* i2c of the left SFP cage (wan) */
+	i2c_sfp1: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	/* i2c of the right SFP cage (lan) */
+	i2c_sfp2: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue_led: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3vd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name  = "fixed-5p1";
+		regulator-min-microvolt = <5100000>;
+		regulator-max-microvolt = <5100000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	/* left SFP cage (wan) */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* right SFP cage (lan) */
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		sfp = <&sfp1>;
+		managed = "in-band-status";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_pins>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pio {
+	i2c_pins: i2c-pins {
+		mux {
+			function = "i2c";
+			groups = "i2c";
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_pereset";
+		};
+	};
+
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_0";
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_rx_tx";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_0_rx_tx";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_led_pins: wf-led-pins {
+		mux {
+			function = "led";
+			groups = "wifi_led";
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan0";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan3";
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			label = "lan4";
+			phy-mode = "2500base-x";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
-- 
2.34.1

Re: [PATCH v4 10/11] arm64: dts: mt7986: add Bananapi R3

[AngeloGioacchino Del Regno]

Il 12/11/22 10:15, Frank Wunderlich ha scritto:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add support for Bananapi R3 SBC.
> 
> - SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
> - all rj45 ports and both SFP working (eth1/lan4)
> - all USB-Ports + SIM-Slot tested
> - i2c and all uarts tested
> - wifi tested (with eeprom calibration data)
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

..snip..

> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
> new file mode 100644
> index 000000000000..def16e36f1e6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
> @@ -0,0 +1,458 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Authors: Sam.Shih <sam.shih@mediatek.com>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + *          Daniel Golle <daniel@makrotopia.org>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt65xx.h>
> +
> +#include "mt7986a.dtsi"
> +
> +/ {
> +	model = "Bananapi BPI-R3";
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";

You have to add the machine compatible to devicetree/bindings/arm/mediatek.yaml
or you get dtb check issues.

Regards,
Angelo

Re: [PATCH v4 10/11] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

Am 14. November 2022 12:50:40 MEZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
>Il 12/11/22 10:15, Frank Wunderlich ha scritto:
>> From: Frank Wunderlich <frank-w@public-files.de>
>> 
>> +/ {
>> +	model = "Bananapi BPI-R3";
>> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
>
>You have to add the machine compatible to devicetree/bindings/arm/mediatek.yaml
>or you get dtb check issues.

Have already:

https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux.git/commit/?h=v6.1-next/dts64&id=8c80453864efea0a0ed5ca2b399fd97f2f55a5ae

>Regards,
>Angelo


regards Frank

Re: [PATCH v4 10/11] arm64: dts: mt7986: add Bananapi R3

[AngeloGioacchino Del Regno]

Il 14/11/22 13:03, Frank Wunderlich ha scritto:
> Am 14. November 2022 12:50:40 MEZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
>> Il 12/11/22 10:15, Frank Wunderlich ha scritto:
>>> From: Frank Wunderlich <frank-w@public-files.de>
>>>
>>> +/ {
>>> +	model = "Bananapi BPI-R3";
>>> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
>>
>> You have to add the machine compatible to devicetree/bindings/arm/mediatek.yaml
>> or you get dtb check issues.
> 
> Have already:
> 
> https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux.git/commit/?h=v6.1-next/dts64&id=8c80453864efea0a0ed5ca2b399fd97f2f55a5ae
> 

Sorry, had missed that one.

In this case:

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>