Devicetree
 help / color / mirror / Atom feed
From: Chancel Liu <chancel.liu@oss.nxp.com>
To: Rob Herring <robh@kernel.org>
Cc: krzk+dt@kernel.org, conor+dt@kernel.org, Frank.Li@nxp.com,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, imx@lists.linux.dev,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v4 1/4] dt-bindings: connector: Add fsl,aud-io-slot binding
Date: Mon, 16 Nov 2026 16:14:26 +0800	[thread overview]
Message-ID: <dd68ae61-9dfd-4138-acf5-b77c63ba0fa3@oss.nxp.com> (raw)
In-Reply-To: <20261112225328.GA1784283-robh@kernel.org>

On 11/13/2026 6:53 AM, Rob Herring wrote:
> On Thu, Nov 05, 2026 at 03:41:14PM +0900, Chancel Liu wrote:
>> From: Chancel Liu <chancel.liu@nxp.com>
>>
>> The NXP AUD-IO slot represents a physically present I/O connector on
>> the base board. It acts as a nexus that exposes a constrained set of
>> I/O resources, such as GPIOs, clocks and interrupts, through fixed
>> electrical wiring. All actual hardware providers reside on the base
>> board. The connector node only defines index-based mappings to those
>> providers.
>>
>> This connector type is present on i.MX95 19x19 EVK and i.MX952 EVK,
>> where it is used to attach the IMX-AUD-IO audio expansion card[1]. The
>> same add-on board can be reused across different base boards that carry
>> this connector.
>>
>> [1]https://www.nxp.com/part/IMX-AUD-IO
> 
> That link is pretty much useless. Is there a pinout definition 
> somewhere?
> 

The detailed user manual (UM12022) is listed as official documentation:
https://docs.nxp.com/bundle/UM12022/page/topics/pcie_interface1.html
But it is behind an NXP login.

The brief pinout table looks like this:

Pin    Signal               Dir
----   ------------------   ---
A11    PCI_AUD_RST_B        In   (GPIO)
A12    AUD_CARD_DET         Out  (INT)
A21    AUD_SPI7_SCLK        In
A22    AUD_SPI7_SS0         In
A25    AUD_SPI7_MOSI        In
A26    AUD_SPI7_MISO        Out
A29    AUD_SPI7_SCLK        In
A30    AUD_SPI7_SS0         In
A32    AUD_SPI7_MISO        Out
A33    AUD_SPI7_MOSI        In
B5     I2C6_SCL_1V8         In
B6     I2C6_SDA_1V8         I/O
B10    AUD_SLOT_PWR_SYNC    In   (GPIO)
B11    AUD_SLOT_PWRDN       In   (GPIO)
B12    AUD_SLOT_MCLK        In   (CLK)
B14    AUD_SLOT_INT_B       Out  (INT)
B15    AUD_SLOT_INT_B       Out
B17    AUD_SLOT_INT_B       Out
B23    SAI2_RXFS            Out
B24    SAI2_RXC             Out
B27    SAI2_TXD1            In
B28    SAI2_TXD2            In
B30    SAI2_TXD3            In
B31    SAI2_RXD1            Out
A2, A3, B1, B2, B3      VCC_EXT_12V0
B8, A9, A10             VCC_EXT_3V3

> Looking at the overlay, this looks incomplete. It looks like there's I2C 
> thru the connector for example. There's also power rails.
>
> The idea with connectors is that overlays apply to the connector node 
> and nothing else.

For this patch set, I2C, I2S and regulators are
provided by the base boards using a common set of labels:

  aud_io_i2c
  aud_io_cpu
  aud_io_reg_1v8
  aud_io_reg_3v3
  aud_io_reg_5v

The common add-on board overlay references these labels directly. This
allows the same overlay to be used with both base boards. But the
overlay still depends on nodes outside the connector.

> I2C we've kind of figured out with something like this:
> 
> connector {
>   i2c-parent = <&i2c>;
>   i2c {
>     ...
>   };
> };
>

I will rework the I2C part using this model.

> Regulators is still open issue though.
> 
> Rob

Good to know this is being discussed. Is there a mailing-list thread or
patch series I can follow?

Regards,
Chancel Liu


  reply	other threads:[~2026-11-16  8:14 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-05  6:41 [PATCH v4 0/4] arm64: dts: freescale: Add IMX-AUD-IO add-on board support Chancel Liu
2026-11-05  6:41 ` [PATCH v4 1/4] dt-bindings: connector: Add fsl,aud-io-slot binding Chancel Liu
2026-11-05  6:59   ` sashiko-bot
2026-11-12 22:53   ` Rob Herring
2026-11-16  8:14     ` Chancel Liu [this message]
2026-11-05  6:41 ` [PATCH v4 2/4] arm64: dts: freescale: imx95-19x19-evk: Add IMX-AUD-IO board support Chancel Liu
2026-11-05  6:41 ` [PATCH v4 3/4] arm64: dts: freescale: imx952-evk: " Chancel Liu
2026-11-05  6:41 ` [PATCH v4 4/4] arm64: dts: freescale: Add common DTS overlay for IMX-AUD-IO add-on board Chancel Liu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=dd68ae61-9dfd-4138-acf5-b77c63ba0fa3@oss.nxp.com \
    --to=chancel.liu@oss.nxp.com \
    --cc=Frank.Li@nxp.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=imx@lists.linux.dev \
    --cc=kernel@pengutronix.de \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh@kernel.org \
    --cc=s.hauer@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox