Re: [PATCH v4 2/3] clk: bcm: Add BCM2711 DVP driver

[Stefan Wahren <stefan.wahren@i2se.com>]

Hi Maxime,

Am 11.06.20 um 11:23 schrieb Maxime Ripard:
> The HDMI block has a block that controls clocks and reset signals to the
> HDMI0 and HDMI1 controllers.
>
> Let's expose that through a clock driver implementing a clock and reset
> provider.
>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: linux-clk@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Reviewed-by: Stephen Boyd <sboyd@kernel.org>
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> ---
>  drivers/clk/bcm/Kconfig           |  11 +++-
>  drivers/clk/bcm/Makefile          |   1 +-
>  drivers/clk/bcm/clk-bcm2711-dvp.c | 120 +++++++++++++++++++++++++++++++-
>  3 files changed, 132 insertions(+)
>  create mode 100644 drivers/clk/bcm/clk-bcm2711-dvp.c
>
> diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig
> index 8c83977a7dc4..784f12c72365 100644
> --- a/drivers/clk/bcm/Kconfig
> +++ b/drivers/clk/bcm/Kconfig
> @@ -1,4 +1,15 @@
>  # SPDX-License-Identifier: GPL-2.0-only
> +
> +config CLK_BCM2711_DVP
> +	tristate "Broadcom BCM2711 DVP support"
> +	depends on ARCH_BCM2835 ||COMPILE_TEST
> +	depends on COMMON_CLK
> +	default ARCH_BCM2835
> +	select RESET_SIMPLE
> +	help
> +	  Enable common clock framework support for the Broadcom BCM2711
> +	  DVP Controller.
> +
>  config CLK_BCM2835
>  	bool "Broadcom BCM2835 clock support"
>  	depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
> diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
> index 0070ddf6cdd2..edb66b44cb27 100644
> --- a/drivers/clk/bcm/Makefile
> +++ b/drivers/clk/bcm/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_CLK_BCM_KONA)	+= clk-kona-setup.o
>  obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm281xx.o
>  obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm21664.o
>  obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
> +obj-$(CONFIG_CLK_BCM2711_DVP)	+= clk-bcm2711-dvp.o
>  obj-$(CONFIG_CLK_BCM2835)	+= clk-bcm2835.o
>  obj-$(CONFIG_CLK_BCM2835)	+= clk-bcm2835-aux.o
>  obj-$(CONFIG_CLK_RASPBERRYPI)	+= clk-raspberrypi.o
> diff --git a/drivers/clk/bcm/clk-bcm2711-dvp.c b/drivers/clk/bcm/clk-bcm2711-dvp.c
> new file mode 100644
> index 000000000000..84dbc886e303
> --- /dev/null
> +++ b/drivers/clk/bcm/clk-bcm2711-dvp.c
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2020 Cerno
> +
> +#include <linux/clk-provider.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset-controller.h>
> +#include <linux/reset/reset-simple.h>
> +
> +#define DVP_HT_RPI_SW_INIT	0x04
> +#define DVP_HT_RPI_MISC_CONFIG	0x08

sorry for not noticing this before. Are these defines specific to the
Raspberry Pi, because of RPI?

Otherwise i like to see this RPI part removed.

Regards
Stefan