Re: [PATCH 2/2] firmware: arm_scmi: Add qcom hvc/shmem transport

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 18/07/2023 20:25, Nikunj Kela wrote:
>>> +
>>> +	scmi_info = devm_kzalloc(dev, sizeof(*scmi_info), GFP_KERNEL);
>>> +	if (!scmi_info)
>>> +		return -ENOMEM;
>>> +
>>> +	np = of_parse_phandle(cdev->of_node, "shmem", 0);
>>> +	if (!of_device_is_compatible(np, "arm,scmi-shmem"))
>> You leak here reference.
> Wouldn't the devm_* API take care of that implicitly? It is same in 
> smc.c as well.

Thanks for bringing my attention to this. I sent a fix for smc.c. Fix
your patch as well, please.

>>> +		return -ENXIO;
>>> +
>>> +	ret = of_address_to_resource(np, 0, &res);
>>> +	of_node_put(np);
>>> +	if (ret) {
>>> +		dev_err(cdev, "failed to get SCMI Tx shared memory\n");
>>> +		return ret;
>>> +	}
>>> +
>>> +	size = resource_size(&res);
>>> +
>>> +	/* let's map 2 additional ulong since
>>> +	 * func-id & capability-id are kept after shmem.
>>> +	 *     +-------+
>>> +	 *     |       |
>>> +	 *     | shmem |
>>> +	 *     |       |
>>> +	 *     |       |
>>> +	 *     +-------+ <-- size
>>> +	 *     | funcId|
>>> +	 *     +-------+ <-- size + sizeof(ulong)
>>> +	 *     | capId |
>>> +	 *     +-------+ <-- size + 2*sizeof(ulong)
>>> +	 */
>>> +
>>> +	scmi_info->shmem = devm_ioremap(dev, res.start,
>>> +					size + 2 * sizeof(unsigned long));
>>> +	if (!scmi_info->shmem) {
>>> +		dev_err(dev, "failed to ioremap SCMI Tx shared memory\n");
>>> +		return -EADDRNOTAVAIL;
>>> +	}
>>> +
>>> +	func_id = readl((void *)(scmi_info->shmem) + size);
>>> +
>>> +#ifdef CONFIG_ARM64
>>> +	cap_id = readq((void *)(scmi_info->shmem) + size +
>>> +		       sizeof(unsigned long));
>>> +#else
>>> +	cap_id = readl((void *)(scmi_info->shmem) + size +
>>> +		       sizeof(unsigned long));
>>> +#endif
>>> +
>>> +	/*
>>> +	 * If there is an interrupt named "a2p", then the service and
>>> +	 * completion of a message is signaled by an interrupt rather than by
>>> +	 * the return of the hvc call.
>>> +	 */
>>> +	irq = of_irq_get_byname(cdev->of_node, "a2p");
>>> +	if (irq > 0) {
>>> +		ret = devm_request_irq(dev, irq, qcom_hvc_msg_done_isr,
>>> +				       IRQF_NO_SUSPEND,
>>> +				       dev_name(dev), scmi_info);
>>> +		if (ret) {
>>> +			dev_err(dev, "failed to setup SCMI completion irq\n");
>> return dev_err_probe, unless this is not called in probe... but then
>> using devm-interface raises questions.
> This is copied as is from existing smc.c

I understand and I hope you understand the code you copied. If there is
a bug in existing code, please do not copy it to new code (like leaking
OF node reference).

Best regards,
Krzysztof