[PATCH v2 0/7] Add TUXEDO Elite 14 Gen1 (X1E78100)

[PATCH v2 0/7] Add TUXEDO Elite 14 Gen1 (X1E78100)

[Georg Gottleuber]

Initial support for TUXEDO Elite 14 Gen1 laptop. It is based on Qualcomm
Snapdragon X Elite SoC (X1E78100).

Changes in v2:
- Rebase to v6.18-rc4/master
- Add support for accelerated video decoding
- Add support for audio (speakers, microphones, headset)
- Add support for Bluetooth
- Add support for camera
- Add support for fingerprint reader
- Add support for HDMI-A port
- Add support for QSEECOM
- Add support for USB Type-A
- Add support for USB-C DP altmode
- Add ASL Xiamen Technology Co. Ltd. vendor prefix
- Add TUXEDO vendor prefix
- Add cover letter
- Removal of pointless comments
- Coding style fixes
- Spell check

The device tree uses the dtschema from Linaro qcom-laptops [1].
ALSA UCM and Audioreach topology patches are available at [2] and [3].
The fingerprint reader requires USB IDs to be patched into libfprint.
WiFi requires a firmware patch [4].

[1]: https://gitlab.com/Linaro/arm64-laptops/linux/-/commit/3d106a8ac261f81e48e4ee2a31b7484d863e0a4a
[2]: https://github.com/Srinivas-Kandagatla/alsa-ucm-conf/tree/x1e80100-tuxedo
[3]: https://github.com/Srinivas-Kandagatla/audioreach-topology/tree/tuxedo-fixes
[4]: https://lore.kernel.org/linux-wireless/59ed6306-28f8-478e-90fe-4a1b73ae3051@tuxedocomputers.com/

Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>

Ettore Chimenti (4):
  dt-bindings: vendor-prefixes: Add ASL Xiamen Technology
  dt-bindings: display: bridge: simple: document the ASL CS5263
    DP-to-HDMI bridge
  drm/bridge: simple: add ASL CS5263 DP-to-HDMI bridge
  firmware: qcom: scm: Allow QSEECOM on Tuxedo Elite 14 Gen1

Georg Gottleuber (3):
  dt-bindings: vendor-prefixes: Add prefix for TUXEDO Computers GmbH
  dt-bindings: arm: qcom: Add TUXEDO Computers device
  arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

 .../devicetree/bindings/arm/qcom.yaml         |    1 +
 .../display/bridge/simple-bridge.yaml         |    1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |    4 +
 arch/arm64/boot/dts/qcom/Makefile             |    2 +
 .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c              |    1 +
 drivers/gpu/drm/bridge/simple-bridge.c        |    5 +
 7 files changed, 1500 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts

-- 
2.43.0

[PATCH v2 1/7] dt-bindings: vendor-prefixes: Add ASL Xiamen Technology

[Georg Gottleuber]

From: Ettore Chimenti <ettore.chimenti@linaro.org>

ASL Xiamen Technology Co. Ltd. is a Chinese high-speed interface and
display system chip design company. Adding it to the vendor prefixes.

Link: https://www.asl-tek.com/

Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index f1d1882009ba..278cb879781f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -176,6 +176,8 @@ patternProperties:
     description: All Sensors Corporation
   "^asix,.*":
     description: ASIX Electronics Corporation
+  "^asl,.*":
+    description: ASL Xiamen Technology Co., Ltd.
   "^aspeed,.*":
     description: ASPEED Technology Inc.
   "^asrock,.*":
-- 
2.43.0

Re: [PATCH v2 1/7] dt-bindings: vendor-prefixes: Add ASL Xiamen Technology

[Krzysztof Kozlowski]

On Wed, Nov 05, 2025 at 04:41:01PM +0100, Georg Gottleuber wrote:
> From: Ettore Chimenti <ettore.chimenti@linaro.org>
> 
> ASL Xiamen Technology Co. Ltd. is a Chinese high-speed interface and
> display system chip design company. Adding it to the vendor prefixes.
> 
> Link: https://www.asl-tek.com/
> 
> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> index f1d1882009ba..278cb879781f 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> @@ -176,6 +176,8 @@ patternProperties:
>      description: All Sensors Corporation
>    "^asix,.*":
>      description: ASIX Electronics Corporation
> +  "^asl,.*":

So the prefix is asl-tek, like its domain.

Best regards,
Krzysztof

Re: [PATCH v2 1/7] dt-bindings: vendor-prefixes: Add ASL Xiamen Technology

[Ettore Chimenti]

On Thu, 6 Nov 2025 at 09:05, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>
> On Wed, Nov 05, 2025 at 04:41:01PM +0100, Georg Gottleuber wrote:
> > From: Ettore Chimenti <ettore.chimenti@linaro.org>
> >
> > ASL Xiamen Technology Co. Ltd. is a Chinese high-speed interface and
> > display system chip design company. Adding it to the vendor prefixes.
> >
> > Link: https://www.asl-tek.com/
> >
> > Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
> > ---
> >  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
> >  1 file changed, 2 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> > index f1d1882009ba..278cb879781f 100644
> > --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> > +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> > @@ -176,6 +176,8 @@ patternProperties:
> >      description: All Sensors Corporation
> >    "^asix,.*":
> >      description: ASIX Electronics Corporation
> > +  "^asl,.*":
>
> So the prefix is asl-tek, like its domain.

Ack. Fixing in v3.

Best Regards,
Ettore

>
> Best regards,
> Krzysztof
>

Re: [PATCH v2 1/7] dt-bindings: vendor-prefixes: Add ASL Xiamen Technology

[Georg Gottleuber]

Am 06.11.25 um 09:05 schrieb Krzysztof Kozlowski:
> On Wed, Nov 05, 2025 at 04:41:01PM +0100, Georg Gottleuber wrote:
>> From: Ettore Chimenti <ettore.chimenti@linaro.org>
>>
>> ASL Xiamen Technology Co. Ltd. is a Chinese high-speed interface and
>> display system chip design company. Adding it to the vendor prefixes.
>>
>> Link: https://www.asl-tek.com/
>>
>> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
>> ---
>>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>>  1 file changed, 2 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
>> index f1d1882009ba..278cb879781f 100644
>> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
>> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
>> @@ -176,6 +176,8 @@ patternProperties:
>>      description: All Sensors Corporation
>>    "^asix,.*":
>>      description: ASIX Electronics Corporation
>> +  "^asl,.*":
> 
> So the prefix is asl-tek, like its domain.

OK, I will include this in v3.
> Best regards,
> Krzysztof
> 
> 

Re: [PATCH v2 1/7] dt-bindings: vendor-prefixes: Add ASL Xiamen Technology

[Krzysztof Kozlowski]

On Wed, Nov 05, 2025 at 04:41:01PM +0100, Georg Gottleuber wrote:
> From: Ettore Chimenti <ettore.chimenti@linaro.org>
> 
> ASL Xiamen Technology Co. Ltd. is a Chinese high-speed interface and
> display system chip design company. Adding it to the vendor prefixes.
> 
> Link: https://www.asl-tek.com/
> 
> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>

Also, incomplete DCO.

Please read submittng patches.

Best regards,
Krzysztof

Re: [PATCH v2 1/7] dt-bindings: vendor-prefixes: Add ASL Xiamen Technology

[Georg Gottleuber]

Am 06.11.25 um 09:07 schrieb Krzysztof Kozlowski:
> On Wed, Nov 05, 2025 at 04:41:01PM +0100, Georg Gottleuber wrote:
>> From: Ettore Chimenti <ettore.chimenti@linaro.org>
>>
>> ASL Xiamen Technology Co. Ltd. is a Chinese high-speed interface and
>> display system chip design company. Adding it to the vendor prefixes.
>>
>> Link: https://www.asl-tek.com/
>>
>> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
> 
> Also, incomplete DCO.

Sorry, I forgot to add my signed-off line to all patches from Ettore.

> Please read submittng patches.
> 
> Best regards,
> Krzysztof
> 

[PATCH v2 2/7] dt-bindings: display: bridge: simple: document the ASL CS5263 DP-to-HDMI bridge

[Georg Gottleuber]

From: Ettore Chimenti <ettore.chimenti@linaro.org>

The ASL CS5263 is a high-performance DP1.4 to HDMI2.0b converter,
designed to connect a DP1.4 source to an HDMI2.0b sink. The CS5263AN
integrates a DP1.4 compliant receiver, and a HDMI2.0b compliant
transmitter.

Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
---
 .../devicetree/bindings/display/bridge/simple-bridge.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml b/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml
index 9ef587d46506..20844f809a87 100644
--- a/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml
@@ -27,6 +27,7 @@ properties:
           - const: adi,adv7123
       - enum:
           - adi,adv7123
+          - asl,cs5263
           - dumb-vga-dac
           - radxa,ra620
           - realtek,rtd2171
-- 
2.43.0

[PATCH v2 3/7] drm/bridge: simple: add ASL CS5263 DP-to-HDMI bridge

[Georg Gottleuber]

From: Ettore Chimenti <ettore.chimenti@linaro.org>

Add support for the transparent ASL CS5263 DP-to-HDMI bridge.

Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
---
 drivers/gpu/drm/bridge/simple-bridge.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/gpu/drm/bridge/simple-bridge.c b/drivers/gpu/drm/bridge/simple-bridge.c
index e4d0bc2200f8..cff7cf3d7a33 100644
--- a/drivers/gpu/drm/bridge/simple-bridge.c
+++ b/drivers/gpu/drm/bridge/simple-bridge.c
@@ -261,6 +261,11 @@ static const struct of_device_id simple_bridge_match[] = {
 			.timings = &default_bridge_timings,
 			.connector_type = DRM_MODE_CONNECTOR_VGA,
 		},
+	}, {
+		.compatible = "asl,cs5263",
+		.data = &(const struct simple_bridge_info) {
+			.connector_type = DRM_MODE_CONNECTOR_HDMIA,
+		},
 	}, {
 		.compatible = "radxa,ra620",
 		.data = &(const struct simple_bridge_info) {
-- 
2.43.0

[PATCH v2 4/7] dt-bindings: vendor-prefixes: Add prefix for TUXEDO Computers GmbH

[Georg Gottleuber]

TUXEDO Computers GmbH is a german supplier for computers.

Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 278cb879781f..a841fe12c9e5 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1677,6 +1677,8 @@ patternProperties:
     description: Theobroma Systems Design und Consulting GmbH
   "^turing,.*":
     description: Turing Machines, Inc.
+  "^tuxedo,.*":
+    description: TUXEDO Computers GmbH
   "^tyan,.*":
     description: Tyan Computer Corporation
   "^tyhx,.*":
-- 
2.43.0

Re: [PATCH v2 4/7] dt-bindings: vendor-prefixes: Add prefix for TUXEDO Computers GmbH

[Krzysztof Kozlowski]

On Wed, Nov 05, 2025 at 04:41:04PM +0100, Georg Gottleuber wrote:
> TUXEDO Computers GmbH is a german supplier for computers.
> 
> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

<form letter>
This is an automated instruction, just in case, because many review
tags are being ignored. If you know the process, just skip it entirely
(please do not feel offended by me posting it here - no bad intentions
intended, no patronizing, I just want to avoid wasted efforts). If you
do not know the process, here is a short explanation:

Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions of patchset, under or above your Signed-off-by tag, unless
patch changed significantly (e.g. new properties added to the DT
bindings). Tag is "received", when provided in a message replied to you
on the mailing list. Tools like b4 can help here ('b4 trailers -u ...').
However, there's no need to repost patches *only* to add the tags. The
upstream maintainer will do that for tags received on the version they
apply.

https://elixir.bootlin.com/linux/v6.15/source/Documentation/process/submitting-patches.rst#L591
</form letter>

Best regards,
Krzysztof

[PATCH v2 5/7] dt-bindings: arm: qcom: Add TUXEDO Computers device

[Georg Gottleuber]

Document the X1E80100-based TUXEDO laptop

Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 18b5ed044f9f..6e5aa9d6e1a8 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1073,6 +1073,7 @@ properties:
               - microsoft,romulus15
               - qcom,x1e80100-crd
               - qcom,x1e80100-qcp
+              - tuxedo,elite14gen1
           - const: qcom,x1e80100
 
       - items:
-- 
2.43.0

Re: [PATCH v2 5/7] dt-bindings: arm: qcom: Add TUXEDO Computers device

[Krzysztof Kozlowski]

On Wed, Nov 05, 2025 at 04:41:05PM +0100, Georg Gottleuber wrote:
> Document the X1E80100-based TUXEDO laptop

Which one? Please use full product names and full sentences ending with
full stop.

Best regards,
Krzysztof

Re: [PATCH v2 5/7] dt-bindings: arm: qcom: Add TUXEDO Computers device

[Georg Gottleuber]

Am 06.11.25 um 09:06 schrieb Krzysztof Kozlowski:
> On Wed, Nov 05, 2025 at 04:41:05PM +0100, Georg Gottleuber wrote:
>> Document the X1E80100-based TUXEDO laptop
> 
> Which one? Please use full product names and full sentences ending with
> full stop.

TUXEDO Elite 14 Gen1, will add this in v3.

> Best regards,
> Krzysztof
> 

Re: [PATCH v2 5/7] dt-bindings: arm: qcom: Add TUXEDO Computers device

[Krzysztof Kozlowski]

On 05/11/2025 16:41, Georg Gottleuber wrote:
> Document the X1E80100-based TUXEDO laptop
> 
> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
> index 18b5ed044f9f..6e5aa9d6e1a8 100644
> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
> @@ -1073,6 +1073,7 @@ properties:
>                - microsoft,romulus15
>                - qcom,x1e80100-crd
>                - qcom,x1e80100-qcp
> +              - tuxedo,elite14gen1
>            - const: qcom,x1e80100

Cover letter says X1E78100, commit msg and bindings say X1E80100.

Something is for sure not saying right. Decide which one.

Best regards,
Krzysztof

Re: [PATCH v2 5/7] dt-bindings: arm: qcom: Add TUXEDO Computers device

[Georg Gottleuber]

Am 06.11.25 um 09:32 schrieb Krzysztof Kozlowski:
> On 05/11/2025 16:41, Georg Gottleuber wrote:
>> Document the X1E80100-based TUXEDO laptop
>>
>> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
>> ---
>>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>>  1 file changed, 1 insertion(+)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
>> index 18b5ed044f9f..6e5aa9d6e1a8 100644
>> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
>> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
>> @@ -1073,6 +1073,7 @@ properties:
>>                - microsoft,romulus15
>>                - qcom,x1e80100-crd
>>                - qcom,x1e80100-qcp
>> +              - tuxedo,elite14gen1
>>            - const: qcom,x1e80100
> 
> Cover letter says X1E78100, commit msg and bindings say X1E80100.
> 
> Something is for sure not saying right. Decide which one.

Oh, true. Thank you. It is a X1E78100. I got confused because the device
tree is also called 'x1e80100-...'.

> Best regards,
> Krzysztof

[PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Georg Gottleuber]

Initial support for TUXEDO Elite 14 Gen1 based on Qualcomm Snapdragon X
Elite SoC (X1E78100).

Working:
* Touchpad
* Keyboard
* eDP (no brightness control yet)
* NVMe
* USB Type-C port
* USB-C DP altmode
* HDMI-A port
* WiFi (WiFi 7 untested)
* Bluetooth
* GPU
* Video decoding
* USB Type-A
* Audio, speakers, microphones
	- 4x speakers.
	- 4x dmic
	- headset
* Camera
* Fingerprint reader

Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |    2 +
 .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
 2 files changed, 1488 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 296688f7cb26..598bf4c6e84a 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -350,3 +350,5 @@ x1p42100-hp-omnibook-x14-el2-dtbs := x1p42100-hp-omnibook-x14.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-hp-omnibook-x14.dtb x1p42100-hp-omnibook-x14-el2.dtb
 x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
+x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
new file mode 100644
index 000000000000..0bfe5931434e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
@@ -0,0 +1,1486 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2025 TUXEDO Computers GmbH
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1e80100.dtsi"
+#include "x1e80100-pmics.dtsi"
+
+/ {
+	model = "TUXEDO Elite 14 Gen1";
+	compatible = "tuxedo,elite14gen1", "qcom,x1e80100";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-0 = <&wcd_default>;
+		pinctrl-names = "default";
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+		};
+	};
+
+	hdmi-bridge {
+		compatible = "asl,cs5263";
+
+		pinctrl-0 = <&hdmi_hpd_default>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_dp_in: endpoint {
+					remote-endpoint = <&usb_1_ss2_qmpphy_out_dp>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				hdmi_bridge_tmds_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_bridge_tmds_out>;
+			};
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss0_ss_out>;
+					};
+				};
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	/*
+	 * TODO: These two regulators are actually part of the removable M.2
+	 * card and not the mainboard. Need to describe this differently.
+	 * Functionally it works correctly, because all we need to do is to
+	 * turn on the actual 3.3V supply above.
+	 */
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E80100-TUXEDO-Elite-14";
+		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
+				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
+				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS1",
+				"VA DMIC1", "MIC BIAS1",
+				"VA DMIC0", "VA MIC BIAS1",
+				"VA DMIC1", "VA MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&left_woofer>, <&left_tweeter>,
+					    <&swr0 0>, <&lpass_wsamacro 0>,
+					    <&right_woofer>, <&right_tweeter>,
+					    <&swr3 0>, <&lpass_wsa2macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <920000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p9: ldo1 {
+			regulator-name = "vreg_l1j_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
+	};
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+
+		reset-gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb5_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb5_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+
+		reset-gpios = <&tlmm 111 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK3>;
+
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&iris {
+	status = "okay";
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	spkr_23_sd_n_active: spkr-23-sd-n-active-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2 {
+	status = "okay";
+};
+
+&mdss_dp2_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	pinctrl-0 = <&edp0_hpd_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp3_out: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+
+	usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pm8550ve_9_gpios {
+	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_5_gpios {
+	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/adsp.mbn",
+			"qcom/x1e80100/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/cdsp.mbn",
+			"qcom/x1e80100/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Woofer */
+	left_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Left Tweeter */
+	left_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&swr3 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Right Woofer */
+	right_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Tweeter */
+	right_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <28 4>, /* Unused */
+			       <44 4>, /* SPI (TPM) */
+			       <238 1>; /* UFS Reset */
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio124";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio111";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb5_reset_n: eusb5-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	hdmi_hpd_default: hdmi-hpd-default-state {
+		pins = "gpio126";
+		function = "usb2_dp";
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-disable;
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&retimer_ss0_ss_in>;
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+/* Right side USB-A (eUSB 3) */
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+/* Left side USB-A (eUSB 6) */
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+/* Right side USB-A (USB-SS 3) */
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p9>;
+
+	status = "okay";
+};
+
+/* Left side USB-A (USB-SS 4) */
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss2_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	/delete-property/ mode-switch;
+	/delete-property/ orientation-switch;
+
+	status = "okay";
+
+	ports {
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/delete-node/ endpoint;
+
+			usb_1_ss2_qmpphy_out_dp: endpoint@0 {
+				reg = <0>;
+
+				data-lanes = <3 2 1 0>;
+				remote-endpoint = <&hdmi_bridge_dp_in>;
+			};
+
+			/* No USB3 lanes connected */
+		};
+	};
+};
+
+/* Camera */
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb5_repeater>;
+
+	status = "okay";
+};
-- 
2.43.0

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Maud Spierings]

Hello Georg,
Great to see another version of this land!

> Initial support for TUXEDO Elite 14 Gen1 based on Qualcomm Snapdragon X
> Elite SoC (X1E78100).
> 
> Working:
> * Touchpad
> * Keyboard
> * eDP (no brightness control yet)
> * NVMe
> * USB Type-C port
> * USB-C DP altmode
> * HDMI-A port
> * WiFi (WiFi 7 untested)
> * Bluetooth
> * GPU
> * Video decoding
> * USB Type-A
> * Audio, speakers, microphones
> 	- 4x speakers.
> 	- 4x dmic
> 	- headset
> * Camera
> * Fingerprint reader
> 
> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
> Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |    2 +
>  .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
>  2 files changed, 1488 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 296688f7cb26..598bf4c6e84a 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -350,3 +350,5 @@ x1p42100-hp-omnibook-x14-el2-dtbs := x1p42100-hp-omnibook-x14.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-hp-omnibook-x14.dtb x1p42100-hp-omnibook-x14-el2.dtb
>  x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
> +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
> +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> new file mode 100644
> index 000000000000..0bfe5931434e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> @@ -0,0 +1,1486 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
> + * Copyright (c) 2025 TUXEDO Computers GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "x1e80100.dtsi"
> +#include "x1e80100-pmics.dtsi"
> +
> +/ {
> +	model = "TUXEDO Elite 14 Gen1";
> +	compatible = "tuxedo,elite14gen1", "qcom,x1e80100";
> +
> +	aliases {
> +		serial0 = &uart21;
> +		serial1 = &uart14;
> +	};
> +
> +	wcd938x: audio-codec {
> +		compatible = "qcom,wcd9385-codec";
> +
> +		pinctrl-0 = <&wcd_default>;
> +		pinctrl-names = "default";
> +
> +		qcom,micbias1-microvolt = <1800000>;
> +		qcom,micbias2-microvolt = <1800000>;
> +		qcom,micbias3-microvolt = <1800000>;
> +		qcom,micbias4-microvolt = <1800000>;
> +		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
> +		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
> +		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
> +		qcom,rx-device = <&wcd_rx>;
> +		qcom,tx-device = <&wcd_tx>;
> +
> +		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
> +
> +		vdd-buck-supply = <&vreg_l15b_1p8>;
> +		vdd-rxtx-supply = <&vreg_l15b_1p8>;
> +		vdd-io-supply = <&vreg_l15b_1p8>;
> +		vdd-mic-bias-supply = <&vreg_bob1>;
> +
> +		#sound-dai-cells = <1>;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-0 = <&hall_int_n_default>;
> +		pinctrl-names = "default";
> +
> +		switch-lid {
> +			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
> +			linux,input-type = <EV_SW>;
> +			linux,code = <SW_LID>;
> +			wakeup-source;
> +		};
> +	};
> +
> +	hdmi-bridge {
> +		compatible = "asl,cs5263";
> +
> +		pinctrl-0 = <&hdmi_hpd_default>;
> +		pinctrl-names = "default";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				hdmi_bridge_dp_in: endpoint {
> +					remote-endpoint = <&usb_1_ss2_qmpphy_out_dp>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +
> +				hdmi_bridge_tmds_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +		};
> +	};
> +
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&hdmi_bridge_tmds_out>;
> +			};
> +		};
> +	};
> +
> +	pmic-glink {
> +		compatible = "qcom,x1e80100-pmic-glink",
> +			     "qcom,sm8550-pmic-glink",
> +			     "qcom,pmic-glink";
> +		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		connector@0 {
> +			compatible = "usb-c-connector";
> +			reg = <0>;
> +			power-role = "dual";
> +			data-role = "dual";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					pmic_glink_ss0_hs_in: endpoint {
> +						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					pmic_glink_ss0_ss_in: endpoint {
> +						remote-endpoint = <&retimer_ss0_ss_out>;
> +					};
> +				};
> +				port@2 {
> +					reg = <2>;
> +
> +					pmic_glink_ss0_con_sbu_in: endpoint {
> +						remote-endpoint = <&retimer_ss0_con_sbu_out>;
> +					};
> +				};
> +			};
> +		};
> +	};

Have you seen the new charge limit properties? Might be a nice thing to 
check out for a next version, see [1].

Link: 
https://lore.kernel.org/all/20250919-qcom_battmgr_update_new-v6-1-ed5c38867614@oss.qualcomm.com/ 
[1]

Kind regards,
Maud

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Krzysztof Kozlowski]

On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
> 
> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
> Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>

Wrong order of tags. Ettore is not sending this.

> ---
>  arch/arm64/boot/dts/qcom/Makefile             |    2 +
>  .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
>  2 files changed, 1488 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 296688f7cb26..598bf4c6e84a 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -350,3 +350,5 @@ x1p42100-hp-omnibook-x14-el2-dtbs := x1p42100-hp-omnibook-x14.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-hp-omnibook-x14.dtb x1p42100-hp-omnibook-x14-el2.dtb
>  x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
> +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
> +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb

Messed ordering. Please do not add to the end of lists. This applies
almost EVERYWHERE, for every sort of change because it only introduces
unnecessary conflicts when applying multiple patchsets.


> +	/*
> +	 * TODO: These two regulators are actually part of the removable M.2
> +	 * card and not the mainboard. Need to describe this differently.
> +	 * Functionally it works correctly, because all we need to do is to
> +	 * turn on the actual 3.3V supply above.
> +	 */
> +	vreg_wcn_0p95: regulator-wcn-0p95 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_WCN_0P95";
> +		regulator-min-microvolt = <950000>;
> +		regulator-max-microvolt = <950000>;
> +
> +		vin-supply = <&vreg_wcn_3p3>;
> +	};
> +
> +	vreg_wcn_1p9: regulator-wcn-1p9 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_WCN_1P9";
> +		regulator-min-microvolt = <1900000>;
> +		regulator-max-microvolt = <1900000>;
> +
> +		vin-supply = <&vreg_wcn_3p3>;
> +	};
> +
> +	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {

w > r, please keep things ordered. See also DTS coding style.

> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_RTMR0_1P15";
> +		regulator-min-microvolt = <1150000>;
> +		regulator-max-microvolt = <1150000>;
> +
> +		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
> +		pinctrl-names = "default";
> +
> +		regulator-boot-on;
> +	};
> +
> +	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_RTMR0_1P8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +
> +		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&usb0_1p8_reg_en>;
> +		pinctrl-names = "default";
> +
> +		regulator-boot-on;
> +	};
> +
> +	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_RTMR0_3P3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&usb0_3p3_reg_en>;
> +		pinctrl-names = "default";
> +
> +		regulator-boot-on;
> +	};
> +
> +	sound {
> +		compatible = "qcom,x1e80100-sndcard";
> +		model = "X1E80100-TUXEDO-Elite-14";
> +		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
> +				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
> +				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
> +				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
> +				"IN1_HPHL", "HPHL_OUT",
> +				"IN2_HPHR", "HPHR_OUT",
> +				"AMIC2", "MIC BIAS2",
> +				"VA DMIC0", "MIC BIAS1",
> +				"VA DMIC1", "MIC BIAS1",
> +				"VA DMIC0", "VA MIC BIAS1",
> +				"VA DMIC1", "VA MIC BIAS1",
> +				"TX SWR_INPUT1", "ADC2_OUTPUT";
> +

No USB ports for DisplayPort/HDMI audio? I think I saw HDMI connector.


Best regards,
Krzysztof

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Georg Gottleuber]

Am 06.11.25 um 09:13 schrieb Krzysztof Kozlowski:
> On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
>>
>> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
>> Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
>> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
> 
> Wrong order of tags. Ettore is not sending this.

Ack.

>> ---
>>  arch/arm64/boot/dts/qcom/Makefile             |    2 +
>>  .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
>>  2 files changed, 1488 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 296688f7cb26..598bf4c6e84a 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -350,3 +350,5 @@ x1p42100-hp-omnibook-x14-el2-dtbs := x1p42100-hp-omnibook-x14.dtb x1-el2.dtbo
>>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-hp-omnibook-x14.dtb x1p42100-hp-omnibook-x14-el2.dtb
>>  x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
>>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
>> +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
>> +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
> 
> Messed ordering. Please do not add to the end of lists. This applies
> almost EVERYWHERE, for every sort of change because it only introduces
> unnecessary conflicts when applying multiple patchsets.

Ack.>
>> +	/*
>> +	 * TODO: These two regulators are actually part of the removable M.2
>> +	 * card and not the mainboard. Need to describe this differently.
>> +	 * Functionally it works correctly, because all we need to do is to
>> +	 * turn on the actual 3.3V supply above.
>> +	 */
>> +	vreg_wcn_0p95: regulator-wcn-0p95 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "VREG_WCN_0P95";
>> +		regulator-min-microvolt = <950000>;
>> +		regulator-max-microvolt = <950000>;
>> +
>> +		vin-supply = <&vreg_wcn_3p3>;
>> +	};
>> +
>> +	vreg_wcn_1p9: regulator-wcn-1p9 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "VREG_WCN_1P9";
>> +		regulator-min-microvolt = <1900000>;
>> +		regulator-max-microvolt = <1900000>;
>> +
>> +		vin-supply = <&vreg_wcn_3p3>;
>> +	};
>> +
>> +	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
> 
> w > r, please keep things ordered. See also DTS coding style.

Ack.

>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "VREG_RTMR0_1P15";
>> +		regulator-min-microvolt = <1150000>;
>> +		regulator-max-microvolt = <1150000>;
>> +
>> +		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +
>> +		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
>> +		pinctrl-names = "default";
>> +
>> +		regulator-boot-on;
>> +	};
>> +
>> +	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "VREG_RTMR0_1P8";
>> +		regulator-min-microvolt = <1800000>;
>> +		regulator-max-microvolt = <1800000>;
>> +
>> +		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +
>> +		pinctrl-0 = <&usb0_1p8_reg_en>;
>> +		pinctrl-names = "default";
>> +
>> +		regulator-boot-on;
>> +	};
>> +
>> +	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "VREG_RTMR0_3P3";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +
>> +		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +
>> +		pinctrl-0 = <&usb0_3p3_reg_en>;
>> +		pinctrl-names = "default";
>> +
>> +		regulator-boot-on;
>> +	};
>> +
>> +	sound {
>> +		compatible = "qcom,x1e80100-sndcard";
>> +		model = "X1E80100-TUXEDO-Elite-14";
>> +		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
>> +				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
>> +				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
>> +				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
>> +				"IN1_HPHL", "HPHL_OUT",
>> +				"IN2_HPHR", "HPHR_OUT",
>> +				"AMIC2", "MIC BIAS2",
>> +				"VA DMIC0", "MIC BIAS1",
>> +				"VA DMIC1", "MIC BIAS1",
>> +				"VA DMIC0", "VA MIC BIAS1",
>> +				"VA DMIC1", "VA MIC BIAS1",
>> +				"TX SWR_INPUT1", "ADC2_OUTPUT";
>> +
> 
> No USB ports for DisplayPort/HDMI audio? I think I saw HDMI connector.

We are going to add that to v3.

Regards,
Georg

> 
> Best regards,
> Krzysztof
> 

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Konrad Dybcio]

On 11/5/25 4:41 PM, Georg Gottleuber wrote:
> Initial support for TUXEDO Elite 14 Gen1 based on Qualcomm Snapdragon X
> Elite SoC (X1E78100).

[...]


> +		wcd-playback-dai-link {
> +			link-name = "WCD Playback";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> +			};
> +
> +			codec {

'co'dec < 'cp'u

Konrad

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Stephan Gerhold]

On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
> Initial support for TUXEDO Elite 14 Gen1 based on Qualcomm Snapdragon X
> Elite SoC (X1E78100).
> 
> Working:
> * Touchpad
> * Keyboard
> * eDP (no brightness control yet)
> * NVMe
> * USB Type-C port
> * USB-C DP altmode
> * HDMI-A port
> * WiFi (WiFi 7 untested)
> * Bluetooth
> * GPU
> * Video decoding
> * USB Type-A
> * Audio, speakers, microphones
> 	- 4x speakers.
> 	- 4x dmic
> 	- headset
> * Camera
> * Fingerprint reader
> 
> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
> Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |    2 +
>  .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
>  2 files changed, 1488 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 296688f7cb26..598bf4c6e84a 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -350,3 +350,5 @@ x1p42100-hp-omnibook-x14-el2-dtbs := x1p42100-hp-omnibook-x14.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-hp-omnibook-x14.dtb x1p42100-hp-omnibook-x14-el2.dtb
>  x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
> +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
> +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb

Please also add x1e80100-tuxedo-elite-14-gen1-el2.dtb here (similar to
the other lines), so that the EL2/KVM-specific DTB is automatically
built and included in the installed DTBs.

> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> new file mode 100644
> index 000000000000..0bfe5931434e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
> @@ -0,0 +1,1486 @@
> [...]
> +	vreg_edp_3p3: regulator-edp-3p3 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_EDP_3P3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&tlmm 54 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&edp_reg_en>;
> +		pinctrl-names = "default";
> +
> +		regulator-always-on;

Does this need to be always on? It should be possible to enable/disable
this supply together with the panel (and it is already set as
power-supply for the panel).

> +		regulator-boot-on;
> +	};
> +
> [...]
> +	sound {
> +		compatible = "qcom,x1e80100-sndcard";
> +		model = "X1E80100-TUXEDO-Elite-14";
> +		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
> +				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
> +				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
> +				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
> +				"IN1_HPHL", "HPHL_OUT",
> +				"IN2_HPHR", "HPHR_OUT",
> +				"AMIC2", "MIC BIAS2",
> +				"VA DMIC0", "MIC BIAS1",
> +				"VA DMIC1", "MIC BIAS1",
> +				"VA DMIC0", "VA MIC BIAS1",
> +				"VA DMIC1", "VA MIC BIAS1",

Please drop the two "VA MIC BIAS" lines, see
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b49e37de8e70bc433b526a9f4382f72b7ac6492e

> +				"TX SWR_INPUT1", "ADC2_OUTPUT";
> +
> +		wcd-playback-dai-link {
> +			link-name = "WCD Playback";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> +			};
> +
> +			codec {
> +				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
> +			};
> +
> +			platform {
> +				sound-dai = <&q6apm>;
> +			};
> +		};
> +
> +		wcd-capture-dai-link {
> +			link-name = "WCD Capture";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
> +			};
> +
> +			codec {
> +				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
> +			};
> +
> +			platform {
> +				sound-dai = <&q6apm>;
> +			};
> +		};
> +
> +		wsa-dai-link {
> +			link-name = "WSA Playback";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
> +			};
> +
> +			codec {
> +				sound-dai = <&left_woofer>, <&left_tweeter>,
> +					    <&swr0 0>, <&lpass_wsamacro 0>,
> +					    <&right_woofer>, <&right_tweeter>,
> +					    <&swr3 0>, <&lpass_wsa2macro 0>;
> +			};
> +
> +			platform {
> +				sound-dai = <&q6apm>;
> +			};
> +		};
> +
> +		va-dai-link {
> +			link-name = "VA Capture";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
> +			};
> +
> +			codec {
> +				sound-dai = <&lpass_vamacro 0>;
> +			};
> +
> +			platform {
> +				sound-dai = <&q6apm>;
> +			};
> +		};
> +	};
> [...]
> +&remoteproc_adsp {
> +	firmware-name = "qcom/x1e80100/adsp.mbn",
> +			"qcom/x1e80100/adsp_dtb.mbn";

We need a custom ADSP firmware for the TUXEDO, so this needs to be a
device-specific path (so that you can upload the correct firmware to
linux-firmware). e.g. "qcom/x1e80100/TUXEDO/adsp.mbn"

> +
> +	status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> +	firmware-name = "qcom/x1e80100/cdsp.mbn",
> +			"qcom/x1e80100/cdsp_dtb.mbn";

If you expect that production versions of this device will have the
(firmware) secure boot enabled, this path should also be
device-specific. If retail versions will allow loading arbitrary
firmware this can stay as-is. 

Same for all other "firmware-name"s.

> +
> +	status = "okay";
> +};
> +
> +&smb2360_0 {
> +	status = "okay";
> +};
> +
> +&smb2360_0_eusb2_repeater {
> +	vdd18-supply = <&vreg_l3d_1p8>;
> +	vdd3-supply = <&vreg_l2b_3p0>;
> +};
> +
> +&smb2360_1 {
> +	status = "okay";
> +};

You have just a single USB-C port, so I would expect that there is also
only a single SMB2360 instance (for charging). Perhaps you can just drop
this node?

Thanks,
Stephan

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Bjorn Andersson]

On Mon, Nov 10, 2025 at 02:41:15PM +0100, Stephan Gerhold wrote:
> On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
[..]
> > +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
> > +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
> 
> Please also add x1e80100-tuxedo-elite-14-gen1-el2.dtb here (similar to
> the other lines), so that the EL2/KVM-specific DTB is automatically
> built and included in the installed DTBs.
> 

Please confirm that this works before adding it.

Regards,
Bjorn

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Stephan Gerhold]

On Mon, Nov 10, 2025 at 10:11:12PM -0600, Bjorn Andersson wrote:
> On Mon, Nov 10, 2025 at 02:41:15PM +0100, Stephan Gerhold wrote:
> > On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
> > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> [..]
> > > +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
> > > +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
> > 
> > Please also add x1e80100-tuxedo-elite-14-gen1-el2.dtb here (similar to
> > the other lines), so that the EL2/KVM-specific DTB is automatically
> > built and included in the installed DTBs.
> > 
> 
> Please confirm that this works before adding it.
> 

Yes, I tested it on the TUXEDO laptop a few weeks ago and it works fine.

In general, I don't think we need to ask everyone submitting new X1E DTs
to test the -el2.dtb separately - the hardware/firmware situation is
similar enough on all the laptops that chances are very high that it
will just work. There are not much device-specific aspects involved.

Thanks,
Stephan

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Georg Gottleuber]

Am 11.11.25 um 10:54 schrieb Stephan Gerhold:
> On Mon, Nov 10, 2025 at 10:11:12PM -0600, Bjorn Andersson wrote:
>> On Mon, Nov 10, 2025 at 02:41:15PM +0100, Stephan Gerhold wrote:
>>> On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
>>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> [..]
>>>> +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
>>>> +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
>>>
>>> Please also add x1e80100-tuxedo-elite-14-gen1-el2.dtb here (similar to
>>> the other lines), so that the EL2/KVM-specific DTB is automatically
>>> built and included in the installed DTBs.
>>>
>>
>> Please confirm that this works before adding it.
>>
> 
> Yes, I tested it on the TUXEDO laptop a few weeks ago and it works fine.
> 
> In general, I don't think we need to ask everyone submitting new X1E DTs
> to test the -el2.dtb separately - the hardware/firmware situation is
> similar enough on all the laptops that chances are very high that it
> will just work. There are not much device-specific aspects involved.

Thanks for testing. Will add this in v3.

> Thanks,
> Stephan

Re: [PATCH v2 6/7] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Georg Gottleuber]

Am 10.11.25 um 14:41 schrieb Stephan Gerhold:
> On Wed, Nov 05, 2025 at 04:41:06PM +0100, Georg Gottleuber wrote:
>> Initial support for TUXEDO Elite 14 Gen1 based on Qualcomm Snapdragon X
>> Elite SoC (X1E78100).
>>
>> Working:
>> * Touchpad
>> * Keyboard
>> * eDP (no brightness control yet)
>> * NVMe
>> * USB Type-C port
>> * USB-C DP altmode
>> * HDMI-A port
>> * WiFi (WiFi 7 untested)
>> * Bluetooth
>> * GPU
>> * Video decoding
>> * USB Type-A
>> * Audio, speakers, microphones
>> 	- 4x speakers.
>> 	- 4x dmic
>> 	- headset
>> * Camera
>> * Fingerprint reader
>>
>> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
>> Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
>> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
>> ---
>>  arch/arm64/boot/dts/qcom/Makefile             |    2 +
>>  .../qcom/x1e80100-tuxedo-elite-14-gen1.dts    | 1486 +++++++++++++++++
>>  2 files changed, 1488 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 296688f7cb26..598bf4c6e84a 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -350,3 +350,5 @@ x1p42100-hp-omnibook-x14-el2-dtbs := x1p42100-hp-omnibook-x14.dtb x1-el2.dtbo
>>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-hp-omnibook-x14.dtb x1p42100-hp-omnibook-x14-el2.dtb
>>  x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
>>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
>> +x1e80100-tuxedo-elite-14-gen1-el2-dtbs	:=  x1e80100-tuxedo-elite-14-gen1.dtb x1-el2.dtbo
>> +dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-tuxedo-elite-14-gen1.dtb
> 
> Please also add x1e80100-tuxedo-elite-14-gen1-el2.dtb here (similar to
> the other lines), so that the EL2/KVM-specific DTB is automatically
> built and included in the installed DTBs.
> 
>> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
>> new file mode 100644
>> index 000000000000..0bfe5931434e
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/x1e80100-tuxedo-elite-14-gen1.dts
>> @@ -0,0 +1,1486 @@
>> [...]
>> +	vreg_edp_3p3: regulator-edp-3p3 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "VREG_EDP_3P3";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +
>> +		gpio = <&tlmm 54 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +
>> +		pinctrl-0 = <&edp_reg_en>;
>> +		pinctrl-names = "default";
>> +
>> +		regulator-always-on;
> 
> Does this need to be always on? It should be possible to enable/disable
> this supply together with the panel (and it is already set as
> power-supply for the panel).

Nice catch. I agree with you.

>> +		regulator-boot-on;
>> +	};
>> +
>> [...]
>> +	sound {
>> +		compatible = "qcom,x1e80100-sndcard";
>> +		model = "X1E80100-TUXEDO-Elite-14";
>> +		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
>> +				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
>> +				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
>> +				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
>> +				"IN1_HPHL", "HPHL_OUT",
>> +				"IN2_HPHR", "HPHR_OUT",
>> +				"AMIC2", "MIC BIAS2",
>> +				"VA DMIC0", "MIC BIAS1",
>> +				"VA DMIC1", "MIC BIAS1",
>> +				"VA DMIC0", "VA MIC BIAS1",
>> +				"VA DMIC1", "VA MIC BIAS1",
> 
> Please drop the two "VA MIC BIAS" lines, see
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b49e37de8e70bc433b526a9f4382f72b7ac6492e

Ack.

>> +				"TX SWR_INPUT1", "ADC2_OUTPUT";
>> +
>> +		wcd-playback-dai-link {
>> +			link-name = "WCD Playback";
>> +
>> +			cpu {
>> +				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
>> +			};
>> +
>> +			codec {
>> +				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
>> +			};
>> +
>> +			platform {
>> +				sound-dai = <&q6apm>;
>> +			};
>> +		};
>> +
>> +		wcd-capture-dai-link {
>> +			link-name = "WCD Capture";
>> +
>> +			cpu {
>> +				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
>> +			};
>> +
>> +			codec {
>> +				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
>> +			};
>> +
>> +			platform {
>> +				sound-dai = <&q6apm>;
>> +			};
>> +		};
>> +
>> +		wsa-dai-link {
>> +			link-name = "WSA Playback";
>> +
>> +			cpu {
>> +				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
>> +			};
>> +
>> +			codec {
>> +				sound-dai = <&left_woofer>, <&left_tweeter>,
>> +					    <&swr0 0>, <&lpass_wsamacro 0>,
>> +					    <&right_woofer>, <&right_tweeter>,
>> +					    <&swr3 0>, <&lpass_wsa2macro 0>;
>> +			};
>> +
>> +			platform {
>> +				sound-dai = <&q6apm>;
>> +			};
>> +		};
>> +
>> +		va-dai-link {
>> +			link-name = "VA Capture";
>> +
>> +			cpu {
>> +				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
>> +			};
>> +
>> +			codec {
>> +				sound-dai = <&lpass_vamacro 0>;
>> +			};
>> +
>> +			platform {
>> +				sound-dai = <&q6apm>;
>> +			};
>> +		};
>> +	};
>> [...]
>> +&remoteproc_adsp {
>> +	firmware-name = "qcom/x1e80100/adsp.mbn",
>> +			"qcom/x1e80100/adsp_dtb.mbn";
> 
> We need a custom ADSP firmware for the TUXEDO, so this needs to be a
> device-specific path (so that you can upload the correct firmware to
> linux-firmware). e.g. "qcom/x1e80100/TUXEDO/adsp.mbn"

Ack.

>> +
>> +	status = "okay";
>> +};
>> +
>> +&remoteproc_cdsp {
>> +	firmware-name = "qcom/x1e80100/cdsp.mbn",
>> +			"qcom/x1e80100/cdsp_dtb.mbn";
> 
> If you expect that production versions of this device will have the
> (firmware) secure boot enabled, this path should also be
> device-specific. If retail versions will allow loading arbitrary
> firmware this can stay as-is. 
> 
> Same for all other "firmware-name"s.

Ack.

>> +
>> +	status = "okay";
>> +};
>> +
>> +&smb2360_0 {
>> +	status = "okay";
>> +};
>> +
>> +&smb2360_0_eusb2_repeater {
>> +	vdd18-supply = <&vreg_l3d_1p8>;
>> +	vdd3-supply = <&vreg_l2b_3p0>;
>> +};
>> +
>> +&smb2360_1 {
>> +	status = "okay";
>> +};
> 
> You have just a single USB-C port, so I would expect that there is also
> only a single SMB2360 instance (for charging). Perhaps you can just drop
> this node?

Tested without this. Seems OK. Ack.

Thanks,
Georg

[PATCH v2 7/7] firmware: qcom: scm: Allow QSEECOM on Tuxedo Elite 14 Gen1

[Georg Gottleuber]

From: Ettore Chimenti <ettore.chimenti@linaro.org>

This is needed to access EFI variables from Linux.

Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
---
 drivers/firmware/qcom/qcom_scm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index e777b7cb9b12..05cf8150fa5e 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -2015,6 +2015,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "qcom,x1e80100-crd" },
 	{ .compatible = "qcom,x1e80100-qcp" },
 	{ .compatible = "qcom,x1p42100-crd" },
+	{ .compatible = "tuxedo,elite14gen1" },
 	{ }
 };
 
-- 
2.43.0

Re: [PATCH v2 7/7] firmware: qcom: scm: Allow QSEECOM on Tuxedo Elite 14 Gen1

[Krzysztof Kozlowski]

On Wed, Nov 05, 2025 at 04:41:07PM +0100, Georg Gottleuber wrote:
> From: Ettore Chimenti <ettore.chimenti@linaro.org>
> 
> This is needed to access EFI variables from Linux.
> 
> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>

Also incomplete DCO.

Best regards,
Krzysztof

Re: [PATCH v2 0/7] Add TUXEDO Elite 14 Gen1 (X1E78100)

[Krzysztof Kozlowski]

On 05/11/2025 16:41, Georg Gottleuber wrote:
> Initial support for TUXEDO Elite 14 Gen1 laptop. It is based on Qualcomm
> Snapdragon X Elite SoC (X1E78100).
> 
> Changes in v2:
> - Rebase to v6.18-rc4/master
> - Add support for accelerated video decoding
> - Add support for audio (speakers, microphones, headset)
> - Add support for Bluetooth
> - Add support for camera
> - Add support for fingerprint reader
> - Add support for HDMI-A port
> - Add support for QSEECOM
> - Add support for USB Type-A
> - Add support for USB-C DP altmode
> - Add ASL Xiamen Technology Co. Ltd. vendor prefix
> - Add TUXEDO vendor prefix
> - Add cover letter
> - Removal of pointless comments
> - Coding style fixes
> - Spell check
> 
> The device tree uses the dtschema from Linaro qcom-laptops [1].

No, it cannot. You must work on mainline.

Specifically, you must use mainline dtschema and I do not understand why
you choose it from some 3rd party repo. See writing-schema how to
install main dtschema package.



Best regards,
Krzysztof

Re: [PATCH v2 0/7] Add TUXEDO Elite 14 Gen1 (X1E78100)

[Georg Gottleuber]

Am 06.11.25 um 09:15 schrieb Krzysztof Kozlowski:
> On 05/11/2025 16:41, Georg Gottleuber wrote:
>> Initial support for TUXEDO Elite 14 Gen1 laptop. It is based on Qualcomm
>> Snapdragon X Elite SoC (X1E78100).
>>
>> Changes in v2:
>> - Rebase to v6.18-rc4/master
>> - Add support for accelerated video decoding
>> - Add support for audio (speakers, microphones, headset)
>> - Add support for Bluetooth
>> - Add support for camera
>> - Add support for fingerprint reader
>> - Add support for HDMI-A port
>> - Add support for QSEECOM
>> - Add support for USB Type-A
>> - Add support for USB-C DP altmode
>> - Add ASL Xiamen Technology Co. Ltd. vendor prefix
>> - Add TUXEDO vendor prefix
>> - Add cover letter
>> - Removal of pointless comments
>> - Coding style fixes
>> - Spell check
>>
>> The device tree uses the dtschema from Linaro qcom-laptops [1].
> 
> No, it cannot. You must work on mainline.
> 
> Specifically, you must use mainline dtschema and I do not understand why
> you choose it from some 3rd party repo. See writing-schema how to
> install main dtschema package.

I am building and testing with mainline dtschema, but checking this dts
with 'make CHECK_DTBS=y qcom/x1e80100-tuxedo-elite-14-gen1.dtb' has
revealed that one property was unevaluated (output: 'data-lanes' was
unexpected [see line 1461]).

This data-lane property is described in the following commit
https://gitlab.com/Linaro/arm64-laptops/linux/-/commit/3d106a8ac261f81e48e4ee2a31b7484d863e0a4a

Due to the warning from the check tool, I just wanted to point out this
commit.

Regards,
Georg


> 
> 
> Best regards,
> Krzysztof

Re: [PATCH v2 0/7] Add TUXEDO Elite 14 Gen1 (X1E78100)

[Georg Gottleuber]

Am 06.11.25 um 13:56 schrieb Georg Gottleuber:
> 
> 
> Am 06.11.25 um 09:15 schrieb Krzysztof Kozlowski:
>> On 05/11/2025 16:41, Georg Gottleuber wrote:
>>> Initial support for TUXEDO Elite 14 Gen1 laptop. It is based on Qualcomm
>>> Snapdragon X Elite SoC (X1E78100).
>>>
>>> Changes in v2:
>>> - Rebase to v6.18-rc4/master
>>> - Add support for accelerated video decoding
>>> - Add support for audio (speakers, microphones, headset)
>>> - Add support for Bluetooth
>>> - Add support for camera
>>> - Add support for fingerprint reader
>>> - Add support for HDMI-A port
>>> - Add support for QSEECOM
>>> - Add support for USB Type-A
>>> - Add support for USB-C DP altmode
>>> - Add ASL Xiamen Technology Co. Ltd. vendor prefix
>>> - Add TUXEDO vendor prefix
>>> - Add cover letter
>>> - Removal of pointless comments
>>> - Coding style fixes
>>> - Spell check
>>>
>>> The device tree uses the dtschema from Linaro qcom-laptops [1].
>>
>> No, it cannot. You must work on mainline.
>>
>> Specifically, you must use mainline dtschema and I do not understand why
>> you choose it from some 3rd party repo. See writing-schema how to
>> install main dtschema package.
> 
> I am building and testing with mainline dtschema, but checking this dts
> with 'make CHECK_DTBS=y qcom/x1e80100-tuxedo-elite-14-gen1.dtb' has
> revealed that one property was unevaluated (output: 'data-lanes' was
> unexpected [see line 1461]).
> 
> This data-lane property is described in the following commit
> https://gitlab.com/Linaro/arm64-laptops/linux/-/commit/3d106a8ac261f81e48e4ee2a31b7484d863e0a4a
> 
> Due to the warning from the check tool, I just wanted to point out this
> commit.

Sorry for not getting that right in my first reply. This commit from
Linaro was also posted to the lkml:

https://lore.kernel.org/all/20251006-topic-x1e80100-hdmi-v5-1-c006311d59d7@linaro.org/

I will include this requirement in the cover letter.
Thanks for the review.

Regards,
Georg